Determinação eletroanalítica de corante reativo presente como contaminante em proteínas purificadas por cromatografia de afinidade

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desenvolvimento e avaliação de eletrodos de difusão gasosa (EDG) para geração de H2O2 in situ e sua aplicação na degradação do corante reativo azul 19

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Adsorção do corante reativo azul 19 em solução aquosa por lama vermelha tratada quimicamente com peró:xido de hidrogênio

Adsorption of Reactive Blue 19 dye onto activated red mud was investigated. Red mud was treated with hydrogen peroxide (LVQ) and heated at both 400 °C (LVQ400) and 500 °C (LVQ500). These samples were characterized by pH, specific surface area, point of zero charge and mineralogical composition. Adsorption was found to be significantly dependent on solution pH, with acidic conditions proving to be the most favorable. The adsorption followed pseudo-second-order kinetics. The Langmuir isotherm was the most appropriate to describe the phenomenon of dye removal using LVQ, LVQ400 and LVQ500, with maximum adsorption capacity of 384.62, 357.14 and 454.54 mg g-1, respectively.

Estudo da interação biosortiva entre o corante reativo procion blue MXG e as linhagens CCB 004, CCB 010 e CCB 650 de Pleurotus ostreatus paramorfogênico

Pós-graduação em Ciências Biológicas (Microbiologia Aplicada) - IBRC

Estudo da adsorção do corante reativo blue 19 por lama vermelha ativada por tratamento químico e térmico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

DESENVOLVIMENTO E AVALIAÇÃO DE ELETRODOS DE DIFUSÃO GASOSA (EDG) PARA GERAÇÃO DE H2O2 IN SITU E SUA APLICAÇÃO NA DEGRADAÇÃO DO CORANTE REATIVO AZUL 19

DEVELOPMENT AND EVALUATION OF GAS DIFFUSION ELECTRODES (GDE) FOR GENERATION OF H2O2 IN SITU AND THEIR APPLICATION IN THE DEGRADATION OF REACTIVE BLUE 19 DYE. This work reports the development of GDE for electrogeneration of H2O2 and their application in the degradation process of Reactive Blue 19 dye. GDE produced by carbon black with 20% polytetrafluoroethylene generated up to 500 mg L-1 of H2O2 through the electrolysis of acidic medium at -0.8 V vs Ag/AgCl. Reactive Blue 19 dye was degraded most efficiently with H2O2 electrogenerated in the presence of Fe(II) ions, leading to removal of 95% of the original color and 39% of TOC at -0.8 V vs Ag/AgCl.

Desenvolvimento e avaliação de eletrodos de difusão gasosa (EDG) para geração de H2O2 in situ e sua aplicação na degradação do corante reativo azul 19

This work reports the development of GDE for electrogeneration of H2O2 and their application in the degradation process of Reactive Blue 19 dye. GDE produced by carbon black with 20% polytetrafluoroethylene generated up to 500 mg L-1 of H2O2 through the electrolysis of acidic medium at -0.8 V vs Ag/AgCl. Reactive Blue 19 dye was degraded most efficiently with H2O2 electrogenerated in the presence of Fe(II) ions, leading to removal of 95% of the original color and 39% of TOC at -0.8 V vs Ag/AgCl.

Caracterização da lama vermelha e sua aplicabilidade na adsorção do corante têxtil Reativo Azul 19

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da hidrólise alcalina da quitina e elaboração de filmes de quitosana para aplicação na adsorção do corante têxtil reativo preto 5

Nesta pesquisa, diferentes amostras de quitosana foram produzidas por diferentes condições de hidrólise alcalina da quitina. A partir das amostras de quitosana foram produzidos filmes,sendo estes aplicados na adsorção do corante têxtil reativo preto 5 e os resultados foram comparados com os dos seus respectivos pós. Os valores das massas molares da quitosana aumentaram em função do aumento do diâmetro da quitina e diminuíram com o aumento da relação de solução NaOH:quitina, da concentração de NaOH e tempo de reação, e ficaram na faixa de 100 a 200 kDa. Um comportamento inverso foi observado para o grau de desacetilação da quitosana, e seus valores variaram de 65 a 95%. Quanto aos filmes biopoliméricos elaborados, os que apresentaram melhores valores quanto as suas propriedades mecânicas e de permeabilidade ao vapor de água foram os filmes produzidos com quitosana de mais elevada massa molar e menor grau de desacetilação. A fim de avaliar o comportamento dos filmes em processos de adsorção, estes foram aplicados na remoção do corante reativo preto 5 (RB5) em diferentes condições de pH (4, 6 e 8). Após, foram escolhidos quatro filmes de quitosana (FQ), com diferentes graus de desacetilação e massas molares, que foram comparados com as quitosanas na forma de pó (PQ) no estudo de adsorção. Este foi realizado sob diversas condições experimentais (pH, temperatura e taxa de agitação) através das isotermas de equilíbrio, da termodinâmica e da cinética. Análises de interação e ciclos de adsorção-dessorção também foram realizados. Verificou-se que PQ e FQ com grau de desacetilação de 95% e massa molar de 100 kDa foram os adsorvente mais adequados, apresentando mais de 99% de remoção do corante RB5 em pH 4,0. Para ambos, PQ e FQ, o modelo de Langmuir foi o mais adequado para representar os dados de equilíbrio. As capacidades máximas de adsorção foram 654,3 e 589,5 mg g-1 para PQ e FQ, respectivamente, obtidos a 298 K. O processo de adsorção foi espontâneo, favorável e exotérmico. A adsorção de RB5 para PQ e FQ seguiu o modelo cinético de Elovich,e ocorreram interações eletrostáticas do PQ-RB5 e do FQ-RB5. Os filmes de quitosana foram reutilizados três vezes, enquanto que a quitosana em pó não pode ser reutilizada.

Análise voltamétrica do corante têxtil do tipo antraquinona empregando eletrodos de carbono impresso

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Utilização de microemulsão na remoção da cor de efluentes têxteis contendo corantes dispersos

Polyester fibers are the most used fibers in the world and disperse dyes are used for dyeing these fibers. After dyeing, the colorful dyebath is discharged into effluent streams, which needs a special treatment for color removal. Surfactants interaction with dyes has been evaluated in several studies, including the textile area, specifically in the separation of dyes from textile wastewater. In this work a cationic surfactant was used in a microemulsion system for the extraction of anionic dyes (disperses dyes) from textile wastewater. These microemulsion system was composed by dodecylamonium chloride (surfactant), kerosene oil (organic phase), isoamyl alcohol (cosurfactant) and the wastewater (aqueous phase). The wastewater that results after the dyeing process is acid (pH 5). It was observed that changing the pH value to above 12.8 the extraction could be made, resulting in an aqueous phase with low color level. The Scheffé net experimental design was used for the extraction process optimization, and the obtained results were evaluated using the program "Statistica 7.0". The optimal microemulsion system was composed by 59.8wt.% of wastewater, 30.1wt.% of kerosene, 3.37wt.% of surfactant and 6.73wt.% of cosurfactant, providing extraction upper than 96%. A mix of reactive dyebath (50%) and disperse dyebath (50%) was used as aqueous phase and it presented extraction upper than 98%. The water phase after extraction process can be reused in a new dyeing, being obtained satisfactory results, according to the limits established by textile industry for a good dyeing. Tests were accomplished seeking to study the influence of salt addition and temperature. An experimental design was used for this purpose, which showed that the extraction doesn't depend on those factors. In this way, the removal of color from textile wastewater by microemulsion is a viable technique (that does not depend of external factors such as salinity and temperature), being obtained good extraction results even with in wastewater mixtures

Estudo do comportamento eletroquímico de alguns agentes antifúngicos utilizando polarografia de pulso diferencial e voltametria de redissolução catódica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Remoção de corantes utilizando tensoativos: extração por ponto de nuvem e floculação iônica

The textile sector is one of the main contributors to the generation of industrial wastewaters due to the use of large volumes of water, which has a high organic load content. In these, it is observed to the presence of dyes, surfactants, starch, alcohols, acetic acid and other constituents, from the various processing steps of the textiles. Hence, the treatment of textile wastewater becomes fundamental before releasing it into water bodies, where they can cause disastrous physical-chemical changes for the environment. Surfactants are substances widely used in separation processes and their use for treating textile wastewaters was evaluated in this research by applying the cloud point extraction and the ionic flocculation. In the cloud point extraction was used as surfactant nonylphenol with 9.5 ethoxylation degree to remove reactive dye. The process evaluation was performed in terms of temperature, surfactant and dye concentrations. The dye removal reached 91%. The ionic flocculation occurs due to the presence of calcium, which reacts with anionic surfactant to form insoluble surfactants capable of attracting the organic matter by adsorption. In this work the ionic flocculation using base soap was applied to the treatment of synthetic wastewater containing dyes belonging to three classes: direct, reactive, and disperse. It was evaluated by the influence of the following parameters: surfactant and electrolyte concentrations, stirring speed, equilibrium time, temperature, and pH. The flocculation of the surfactant was carried out in two ways: forming the floc in the effluent itself and forming the floc before mixing it to the effluent. Removal of reactive and direct dye, when the floc is formed into textile effluent was 97% and 87%, respectively. In the case where the floc is formed prior to adding it to the effluent, the removal to direct and disperse dye reached 92% and 87%, respectively. These results show the efficience of the evaluated processes for dye removal from textile wastewaters.

Adsorção do corante amarelo reativo BF-4G 200% por argila esmectita

This study aimed to evaluate the potential use of smectite clays for color removal of textile effluents. The experiments were performed by testing exploratory/planning method factorial and fractional factorial where the factors and levels are predetermined. The smectite clays were used originating from gypsum hub of the region Araripe-PE, and the dye used was Reactive Yellow BF-4G 200%. The smectite clay was collected and transported to the Laboratory of Soil Physics of UFRPE, where it held its preparation through air drying, lump breaking and classification in sieve to then submit it to the adsorption process. Upon completion of 22 complete factorial design it was concluded that the values of (96, 96,5 and 95,8%) corresponding to the percentage of of removal for "in-kind", chemically and thermally activated, respectively and adsorbed amounts of (4,80, 4,61 and 4,74 mg/g) for three clays. Showed that the activation processes used did not increase the adsorption capacity of smectite clay. The kinetic data were best fitted to the Freundlich isotherm, with an exponential distribution of active sites and that shows above the Langmuir equation for adsorption of cations and anions by clays. The kinetic model that best adapted to the results was the pseudosecond order model. In the factorial design study 24-1, at concentrations up to 500 mg/L obtains high percentage of color removal (92,37, 90,92 and 93,40%) and adsorbed amount (230,94, 227,31 and 233,50 mg/g) for three clays. The kinetic data fitted well to Langmuir and Freundlich isotherms. The kinetic model that best adapted to the results was the pseudosecond order model

Aplicação de Neurospora crassa para avaliação da biosorção e biodegradação de corantes ácido, xanteno, diretos e reativo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)