Investigating the of Water treatment residuals on Phosphorus mobility derived from biosolid application to Willow coppice

Short rotation willow coppice (SRWC) treatment of biosolids is limited by the oversupply of biosolid derived phosphorus; this can lead to eventual losses of phosphorus to water. Water treatment residuals (WTR), a by-product of potable water treatment, have been identified as a viable soil amendment for mitigation of phosphorus loss. WTR exploit the capacity of internally held aluminium oxide-hydroxide complexes to immobilise labile phosphorus. However indiscriminate additions to plots can result in inadequate control or excessive immobilization of soluble P, leading to crop deficiencies. Four commercially grown common willow (Salix) genotypes (Terra Nova, Endeavour, Resolution and Tora) were grown in soil amended with WTR at five different application rates (0, 10, 25, 50 and 100 tonne ha-1 air-dry basis) in a glasshouse pot experiment. The effects of application rates on plant yields, tissue P concentrations, P uptake and soil labile P availability were measured. Results indicate labile P was reduced with increasing WTR application rates, without any negative agronomic impacts.

Drivers of increased soil respiration in a poplar coppice exposed to elevated CO2

Background and Aims. The response of soil respiration (SR) to elevated CO2 is driven by a number of processes and feedbacks. This work aims to i) detect the effect of elevated CO2 on soil respiration during the second rotation of a short rotation forest, at two levels of N availability; and ii) identify the main drivers behind any changes in soil respiration. Methods. A poplar plantation (POP-EUROFACE) was grown for two rotations of three years under elevated CO2 maintained by a FACE (Free Air CO2 Enrichment) technique. Root biomass, litter production and soil respiration were followed for two consecutive years after coppice. Results. In the plantation, the stimulation of fine root and litter production under elevated CO2 observed at the beginning of the rotation declined over time. Soil respiration (SR) was continuously stimulated by elevated CO2, with a much larger enhancement during the growing (up to 111 %) than in the dormant season (40 %). The SR increase at first appeared to be due to the increase in fine root biomass, but at the end of the 2nd rotation was supported by litter decomposition and the availability of labile C. Soil respiration increase under elevated CO2 was not affected by N availability. Conclusions. The stimulation of SR by elevated CO2 was sustained by the decomposition of above and belowground litter and by the greater availability of easily decomposable substrates into the soil. C losses through SR were greater in the last year of the plantation due to a lack of effect of elevated CO2 on C allocation to roots, reducing the potential for C accumulation.

Survey of influence of biomass mineral matter in thermochemical conversion of short rotation willow coppice

Short rotation willow coppice (SRC) has been investigated for the influence of K, Ca, Mg, Fe and P on its pyrolysis and combustion behaviours. These metals are the typical components that appear in biomass. The willow sample was pretreated to remove salts and metals by hydrochloric acid, and this demineralised sample was impregnated with each individual metal at the same mol g biomass (2.4 × 10 mol g demineralised willow). Characterisation was performed using thermogravimetric analysis (TGA), and differential thermal analysis (DTA) for combustion. In pyrolysis, volatile fingerprints were measured by means of pyrolysis-gas chromatography-mass spectrometry (PY-GC-MS). The yields and distribution of pyrolysis products have been influenced by the presence of the catalysts. Most notably, both potassium and phosphorous strongly catalysed the pyrolysis, modifying both the yield and distribution of reaction products. Temperature programmed combustion TGA indicates that combustion of biomass char is catalysed by all the metals, while phosphorus strongly inhibits the char combustion. In this case, combustion rates follow the order for volatile release/combustion: P>K>Fe>Raw>HCl>Mg>Ca, and for char combustion K>Fe>raw>Ca-Mg>HCl>P. The samples impregnated with phosphorus and potassium were also studied for combustion under flame conditions, and the same trend was observed, i.e. both potassium and phosphorus catalyse the volatile release/combustion, while, in char combustion, potassium is a catalyst and phosphorus a strong inhibitor, i.e. K impregnated>(faster than) raw>demineralised»P impregnated.

Potassium catalysis in the pyrolysis behaviour of short rotation willow coppice

Short rotation willow coppice (SRC) and a synthetic biomass, a mixture of the basic biomass components (cellulose, hemicellulose and lignin), have been investigated for the influence of potassium on their pyrolysis behaviours. The willow sample was pre-treated to remove salts and metals by hydrochloric acid, and this demineralised sample was impregnated with potassium. The same type of pre-treatment was applied to components of the synthetic biomass. Characterisation was performed using thermogravimetric analysis with measurement of products by means of Fourier transform infrared spectroscopy (TGA-FTIR) and pyrolysis-gas chromatography-mass spectrometry (PY-GC-MS). A comparison of product distributions and kinetics are reported. While the general features of decomposition of SRC are described well by an additive behaviour of the individual components, there are some differences in the magnitude of the influence of potassium, and on the products produced. For both SRC and the synthetic biomass, TGA traces indicate catalytic promotion of both of the two-stages of biomass decomposition, and potassium can lower the average apparent first-order activation energy for pyrolysis by up to 50 kJ/mol. For both SRC and synthetic biomass the yields and distribution of pyrolysis products have been influenced by the presence of the catalyst. Potassium catalysed pyrolysis increases the char yields markedly and this is more pronounced for synthetic biomass than SRC. Gas evolution profiles during pyrolysis show the same general features for both SRC and synthetic biomass. Relative methane yields increase during the char formation stage of pyrolysis of the potassium doped samples. The evolution profiles of acetic acid and formaldehyde change, and these products are seen in lower relative amounts for both the demineralised samples. A greater variation in pyrolysis products is observed from the treated SRC samples compared to the different synthetic biomass samples. Furthermore, substituted phenols from lignin pyrolysis are more dominant in the pyrolysis profiles of the synthetic biomass than of the SRC, implying that the extracted lignins used in the synthetic biomass yield a greater fraction of monomeric type species than the lignocellulosic cell wall material of SRC. For both types of samples, PY-GS-MS analyses show that potassium has a significant influence on cellulose decomposition markers, not just on the formation of levoglucosan, but also other species from the non-catalysed mechanism, such as 3,4-dihydroxy-3-cyclobutene-1,2-dione. © 2007 Elsevier Ltd. All rights reserved.

Evaluation of the ECOSSE model for simulating soil organic carbon under Miscanthus and short rotation coppice-willow crops in Britain

Acknowledgements This work contributes to the ELUM (Ecosystem Land Use Modelling & Soil Carbon GHG Flux Trial) project, which was commissioned and funded by the Energy Technologies Institute (ETI). We acknowledge the E-OBS data set from the EU-FP6 project ENSEMBLES (http://ensembles-eu.metoffice.com) and the data providers in the ECA&D project (http://www.ecad.eu).

The environmental and economic sustainability of potential bioethanol from willow in the UK.

Life cycle assessment has been used to investigate the environmental and economic sustainability of a potential operation in the UK in which bioethanol is produced from the hydrolysis and subsequent fermentation of coppice willow. If the willow were grown on idle arable land in the UK, or, indeed, in Eastern Europe and imported as wood chips into the UK, it was found that savings of greenhouse gas emissions of 70-90%, when compared to fossil-derived gasoline on an energy basis, would be possible. The process would be energetically self-sufficient, as the co-products, e.g. lignin and unfermented sugars, could be used to produce the process heat and electricity, with surplus electricity being exported to the National Grid. Despite the environmental benefits, the economic viability is doubtful at present. However, the cost of production could be reduced significantly if the willow were altered by breeding to improve its suitability for hydrolysis and fermentation.

The machinist landscape:Land Art Generator Initiative (Competition)

THE MACHINIST LANDSCAPE: AN ENTROPIC GRID OF VARIANCE
‘By drawing a diagram, a ground plan of a house, a street plan to the location of a site, or a topographic map, one draws a “logical two dimensional picture”. A “logical picture” differs from a natural or realistic picture in that it rarely looks like the thing it stands for.’
A Provisional Theory of Non-Sites, Robert Smithson (1968)

Between design and ground there are variances, deviations and gaps. These exist as physical interstices between what is conceptualised and what is realised; and they reveal moments in the design process that resist the reconciliation of people and their environment (McHarg 1963). The Machinist Landscape interrogates the significance of these variances through the contrasting processes of coppice and photovoltaic energy. It builds on the potential of these gaps, and in doing so proposes that these spaces of variance can reveal the complexity of relationships between consumption and remediation, design and nature.
Fresh Kills Park, and in particular the draft master plan (2006), offers a framework to explore this artificial construct. Central to the Machinist Landscape is the analysis of the landfill gas collection system, planned on a notional 200ft grid. Variations are revealed between this diagrammatic grid measure and that which has been constructed on the site. These variances between the abstract and the real offer the Machinist Landscape a powerful space of enquiry. Are these gaps a result of unexpected conditions below ground, topographic nuances or natural phenomena? Does this space of difference, between what is planned and what is constructed, have the potential to redefine the dynamic processes and relations with the land?
The Machinist Landscape is structured through this space of variance with an ‘entropic grid’, the under-storey of which hosts a carefully managed system of short-rotation coppice (SRC). The coppice, a medieval practice related to energy, product, and space, operates on theoretical and programmatic levels. It is planted along a structure of linear bunds, stabilized through coppice pole retaining structures and enriched with nutrients from coppice produced bio-char. Above the coppice is built an upper-storey of photovoltaic (PV); its structures fabricated from the coppiced timber and the PV produced with graphene from coppice charcoal processes.

Energy balance of SRC willow used for managing farmyard washings - how does it compare to a conventional wastewater treatment works?

The water and wastewater industry in the UK accounts for around 3% of total energy use and just over 1% of total UK greenhouse gas emissions. Targets for greenhouse gas emissions reduction and higher renewable energy penetration, coupled with rising energy costs, growing demand for wastewater services and tightening EU water quality requirements, have led to an increased interest in alternative wastewater treatment methods. The use of short rotation coppice (SRC) willow for the treatment of wastewater effluent is one such alternative, which brings with it the dual benefits of wastewater treatment and production of biomass for energy. In order to assess the effectiveness of SRC willow, it is important to analyse the overall energy balance in terms of energy input versus energy output. This paper carries out an energy life cycle analysis of a specific SRC willow plantation in Northern Ireland to which farmyard washings (dirty water) are applied. The system boundaries include the establishment, maintenance, and harvesting of the plantation, along with the transport and drying of the wood for biomass combustion. The analysis shows that the overall energy balance is positive, and that the direct and indirect energy demands are 12% and 8% of gross energy production respectively. The energy demands of the plantation are compared with the energy required to treat an equivalent nutrient load in a conventional wastewater treatment plant. While a conventional plant consumes 2.6 MJ/m3 , the irrigation system consumes 1.6 MJ/m3 and the net energy production of the scenario is 48 MJ/m3 .

Logistics management and costs of biomass fuel supply

Discusses part of a project conducted by the authors into the logistics planning and management and costs of supplying biomass fuels to biomass-fired power stations in the UK. Defines biomass fuels and the reasons for the growth in interest in their use for electricity generation. The activities and parties involved in the biomass fuel supply chain are discussed together with the management of the chain in order to achieve smooth and consistent flow of biomass fuel to power stations. Explains the approach used to modelling the delivered costs of biomass fuels for four types of biomass fuel included in the project: forest fuel, short rotation coppice, straw and miscanthus. Comments are given on the environmental impacts of the fuel supply chains. The results indicate that straw supply systems are capable of producing the lowest delivered costs of the four fuels studied. Short rotation coppice and miscanthus, two new energy crops, are likely to have the highest delivered costs at present. This is due to the cost of growing these fuels and the financial incentives required by farmers to persuade them to grow these crops. Logistics costs (i.e. transport, storage and handling) are shown to represent a significant proportion of total delivered cost in biomass supply. Careful supply chain planning and logistics management will be of central importance to the success of the biomass industry.

Évaluation du potentiel de séquestration de carbone dans le sol de cultures intensives sur courtes rotations de saules dans le sud du Québec

Dans la dernière décennie, plusieurs hectares de terre agricole ont été convertis à la culture intensive sur courtes rotations (CICR) de saules dans le sud du Québec (Canada). Peu d’études ont été réalisées afin de déterminer comment se comporte la dynamique du carbone organique (Corg) dans le sol suivant cette conversion. Nous avons donc comparé la quantité du Corg et de deux pools labiles de carbone (carbone extractible à l’eau chaude et les sucres aminés) entre des CICR en phase initiale d’établissement (1-2 ans) et des parcelles appariées représentant le système de culture qui prévalait avant la transformation en culture de saules (culture fourragère) et d’autres cultures d’intérêt. La même chose a été faite pour une CICR en exploitation (depuis 9 ans) à un autre site. La quantité de Corg du sol n’était pas différente entre les CICR et les parcelles sous culture fourragère. Une plus haute concentration de sucres aminés dans le Corg total des CICR en établissement, par rapport aux autres parcelles sur le même site, permet de soupçonner que les perturbations liées à l’établissement ne mènent pas à une minéralisation accrue du Corg à court terme. La proportion de sucres aminés fongiques, qui diminue théoriquement lors de perturbations, était aussi plus élevée sous la plus jeune culture. Sous la CICR de neuf ans, le Corg était redistribué dans le profil vertical et les pools labiles étaient de plus petite taille (à une profondeur de 20-40 cm) comparativement à une parcelle témoin. La conversion d’une culture fourragère en plantation de saules en CICR n’a pas mené à la formation d’un puits de carbone. L’étude laisse entrevoir qu’un tel puits pourrait être créé si la conversion se faisait à partir d’un aménagement impliquant la culture en rotation de plantes annuelles et des labours.

Séquestration du carbone atmosphérique dans la biomasse racinaire de plantations de saules

Le cycle du carbone (C) est, depuis la révolution industrielle, déstabilisé par l’introduction dans l’atmosphère de C autrefois fossilisé. Certaines mesures de mitigation prometteuses impliquent la séquestration accrue du CO2 atmosphérique dans les sols via le développement du réseau racinaire des arbres. Ce projet de recherche visait à : 1) quantifier la biomasse racinaire ligneuse produite annuellement par unité de surface par le Salix miyabeana cultivé en régie intensive à courtes rotations, 2) doser la concentration en C et en N des racines de saule en fonction de leur profondeur et de leur diamètre et 3) déterminer l’influence des propriétés pédoclimatiques du milieu sur la séquestration du carbone organique (Corg) par les racines. Pour y arriver, six souches de saules ont été excavées à partir de huit sites (n=48) et neuf carottes de recolonisation ont été implantées à cinq sites (n=45) pour évaluer la productivité racinaire fine. Les échantillons séchés ont été pesés pour quantifier la biomasse racinaire produite, et ont été analysés pour le C et le N. La productivité en biomasse racinaire ligneuse du saule en plantation pour tout le réseau d'échantillonnage varie de 0,7 – 1,8 Mg/ha/an. La proportion de C dans la biomasse racinaire s’étend de 31,3% à 50,4% et sa variance dans les tissus est expliquée par le diamètre racinaire et par les conditions environnementales des sites de provenance. Les conditions climatiques constituent la principale influence sur la production de biomasse racinaire. La variance de la biomasse racinaire est significativement contrôlée (p :0,004) par la quantité de précipitation de l’été et de l’année qui contrôlent ensemble 83,4 % du r2 ajusté. La précipitation de l’été est inversement liée à la productivité racinaire puisque les protéines expansines des racines sont stimulées par les carences hydriques du sol. La production de racines fines des plantations (1,2 à 2,4 Mg/ha/an) est, elle, plus fortement contrôlée par les conditions pédologiques du site qui expliquent 36,5% de la variance de productivité des racines fines contre 37,5% de la variance expliquée par les facteurs pédoclimatiques. Le P et le N du sol ont des rôles prépondérants sur la production de racines fines. Une disponibilité en P accrue dans le sol stimule la biomasse racinaire fine alors qu’une quantité supérieure de N dans le sol limite la croissance racinaire tout en favorisant la croissance des parties aériennes de la plante. Ce projet a permis d’améliorer notre compréhension des conditions pédologiques et climatiques qui engendrent, au Québec méridional, une productivité et une séquestration en Corg accrue dans le réseau racinaire du saule.

Effets de facteurs pédoclimatiques sur la composition et l’anatomie du bois de cinq cultivars de saule destinés aux biocarburants

En 2011, cinq (5) cultivars de saules ont été sélectionnés pour leur rendement en biomasse. Ils ont été plantés sur quatre sites de la province du Québec et ont été maintenus selon le protocole de la culture intensive sur courtes rotations (CICR) afin de déterminer leur potentiel pour la bioénergie dans des environnements contrastés. La composition et l’anatomie du bois de ces cultivars ont été caractérisées et comparés en fonction des conditions environnementales caractéristiques de chaque site. La hauteur et le diamètre à la base des plantes diffèrent selon les sites. Ainsi, les cultivars répondent de façon spécifique aux conditions pédoclimatiques dans lesquelles ils sont cultivés. L’effet de l’environnement n’a pas été mis en évidence sur la teneur en lignine des cultivars. Cependant, un effet génotypique a pu être constaté soulignant l’importance de la sélectivité des cultivars. La densité du bois a étonnamment conservé la même hiérarchie génotypique entre les sites. À l’opposé, l’anatomie du bois présente des différences notamment au niveau des caractéristiques des fibres et des vaisseaux. Une forte teneur en polyphénols ainsi que des fibres moins larges et des vaisseaux plus nombreux ont été observés sur le site dont le bois est le plus dense supposant l’effet probable d’un stress abiotique. De plus, deux fois plus de fibres gélatineuses, fibres riches en cellulose, ont été identifiées sur ce site montrant un intérêt pour la production de bioéthanol.

Bio-energy retains its mitigation potential under elevated CO2

Background If biofuels are to be a viable substitute for fossil fuels, it is essential that they retain their potential to mitigate climate change under future atmospheric conditions. Elevated atmospheric CO2 concentration [CO2] stimulates plant biomass production; however, the beneficial effects of increased production may be offset by higher energy costs in crop management. Methodology/Main findings We maintained full size poplar short rotation coppice (SRC) systems under both current ambient and future elevated [CO2] (550 ppm) and estimated their net energy and greenhouse gas balance. We show that a poplar SRC system is energy efficient and produces more energy than required for coppice management. Even more, elevated [CO2] will increase the net energy production and greenhouse gas balance of a SRC system with 18%. Managing the trees in shorter rotation cycles (i.e. 2 year cycles instead of 3 year cycles) will further enhance the benefits from elevated [CO2] on both the net energy and greenhouse gas balance. Conclusions/significance Adapting coppice management to the future atmospheric [CO2] is necessary to fully benefit from the climate mitigation potential of bio-energy systems. Further, a future increase in potential biomass production due to elevated [CO2] outweighs the increased production costs resulting in a northward extension of the area where SRC is greenhouse gas neutral. Currently, the main part of the European terrestrial carbon sink is found in forest biomass and attributed to harvesting less than the annual growth in wood. Because SRC is intensively managed, with a higher turnover in wood production than conventional forest, northward expansion of SRC is likely to erode the European terrestrial carbon sink.

Stomatal conductance and not stomatal density determines the long-term reduction in leaf transpiration of poplar in elevated CO2

Using a free-air CO2 enrichment (FACE) experiment, poplar trees (Populus · euramericana clone I214) were exposed to either ambient or elevated [CO2] from planting, for a 5-year period during canopy development, closure, coppice and re-growth. In each year, measurements were taken of stomatal density (SD, number mm2) and stomatal index (SI, the proportion of epidermal cells forming stomata). In year 5, measurements were also taken of leaf stomatal conductance (gs, lmol m2 s1), photosynthetic CO2 fixation (A, mmol m2 s1), instantaneous water-use efficiency (A/E) and the ratio of intercellular to atmospheric CO2 (Ci:Ca). Elevated [CO2] caused reductions in SI in the first year, and in SD in the first 2 years, when the canopy was largely open. In following years, when the canopy had closed, elevated [CO2] had no detectable effects on stomatal numbers or index. In contrast, even after 5 years of exposure to elevated [CO2], gs was reduced, A/E was stimulated, and Ci:Ca was reduced relative to ambient [CO2]. These outcomes from the long-term realistic field conditions of this forest FACE experiment suggest that stomatal numbers (SD and SI) had no role in determining the improved instantaneous leaf-level efficiency of water use under elevated [CO2]. We propose that altered cuticular development during canopy closure may partially explain the changing response of stomata to elevated [CO2], although the mechanism for this remains obscure.

Prediction of moisture, calorific value, ash and carbon content of two dedicated bioenergy crops using near-infrared spectroscopy

The potential of near infrared spectroscopy in conjunction with partial least squares regression to predict Miscanthus xgiganteus and short rotation coppice willow quality indices was examined. Moisture, calorific value, ash and carbon content were predicted with a root mean square error of cross validation of 0.90% (R2 = 0.99), 0.13 MJ/kg (R2 = 0.99), 0.42% (R2 = 0.58), and 0.57% (R2 = 0.88), respectively. The moisture and calorific value prediction models had excellent accuracy while the carbon and ash models were fair and poor, respectively. The results indicate that near infrared spectroscopy has the potential to predict quality indices of dedicated energy crops, however the models must be further validated on a wider range of samples prior to implementation. The utilization of such models would assist in the optimal use of the feedstock based on its biomass properties.