The influence ofvariable amplitude loading on the fatigue strength of rhs corners

Rectangular hollow section (RHS) members are components widely used in engineering applications because of their good-looking, good properties in engineering areas and inexpensive cost comparing to members with other sections. The increasing use of RHS in load bearing structures makes it necessary to analyze the fatigue behavior of the RHS members. In this thesis, concentration will be given to the fatigue behavior of the RHS members under variable amplitude pure torsional loading. For the RHS members, failure will normally occur in the corner region if the welded regions are under full penetration. This is because of the complicated stress components' distributions at the RHScorners, where all of three fracture mechanics modes will happen. Mode I is mainly caused by the residual stresses that caused by the manufacturing process. Modes II and III are caused by the applied torsional loading. Stress based Findleymodel is also used to analyze the stress components. Constant amplitude fatigue tests have been done as well as variable amplitude fatigue tests. The specimens under variable amplitude loading gave longer fatigue lives than those under constant amplitude loading. Results from tests show an S-N curvewith slope around 5.

Fatigue crack growth of Al 7475 T761 under constant and variable amplitude loading

Experimental programs in constant and variable amplitude loading were performed to obtain a x N curves and to study retardation in fatigue crack growth due to overloads. The main aim of this research program was to analyse the effect of overload ratio and number of overload peaks. The effect of underloads, before and after the overload blocks was also studied. The generalised equation of Paris-Erdogan type was used for modelling of obtained data on crack propagation under constant amplitude load.

Avaliação do comportamento em fadiga de juntas estruturais de ligas de Al2024T3 coladas com adesivo epóxi

Ligas de alumínio são extensamente usadas em partes aeronáuticas devido às boas propriedades mecânicas e baixa densidade. Estas partes devem ser unidas para formar conjuntos maiores. Uma junta estrutural é definida como um segmento de estrutura que provê um meio de transferir carga de um elemento estrutural para outro. A maioria das juntas aeronáuticas é mecanicamente fixada com múltiplos prendedores (parafusos ou rebites). Estas juntas apresentam uma alta concentração de tensões ao redor do prendedor, porque a transferência de carga entre elementos da junta acontece em uma fração da área disponível. Por outro lado, as cargas aplicadas em juntas adesivas são distribuídas sobre toda a área colada e reduz os pontos de concentração de tensão. Juntas são a fonte mais comum de falhas estruturais em aeronaves e quase todos os reparos envolvem juntas. Portanto, é importante entender todos os aspectos de projeto e análise de juntas. O objetivo deste trabalho é comparar estaticamente juntas estruturais de ligas de Al2024-T3 em três condições: juntas mecanicamente rebitadas, juntas coladas e uma configuração híbrida rebitada e colada. Foi usada a norma NASM 1312-4 para confecção dos corpos-de-prova. Além disso, foram conduzidos testes de fadiga, sob amplitude de carregamento constante e razão de tensão igual a 0,1 para avaliar a eficiência dos elementos estruturais durante sua vida em serviço. Os resultados mostraram que a configuração híbrida apresenta maior resistência estática e uma vida em fadiga superior à configuração colada.

Modeling the growth of LT and TL-oriented fatigue cracks in longitudinally and transversely pre-strained Al 2524-T3 alloy

The aluminum alloy 2524 (Al-Cu-Mg) was developed during the 90s mainly to be employed in aircraft fuselage panels, replacing the standard Al 2024. In the present analysis the fatigue crack growth (FCG) behavior of 2524-T3 was investigated, regarding the influence of three parameters: load ratio, pre strain and crack plane orientation of the material. The pre strain of aluminum alloys is usually performed in order to obtain a more homogeneous precipitates distribution, accompanied by an increase in the yield strength. In this work, it was evaluated the resistance of Al 2524-T3 sheet samples to the fatigue crack growth, having L-T and T-L crack orientations. FCG tests were performed under constant amplitude loading at three distinct positive load ratios. The three material conditions were tested: as received(AR), pre strained longitudinally (SL) and transversally (ST) in relation to rolling direction. In order to describe FCG behavior, two-parameter kinetic equations were compared: a Paris-type potential model and a new exponential equation introduced in a previous work conducted by our research group. It was observed that the exponential model, which takes into account the deviations from linearity presented by da/dN versus AK data, describes more adequately the FCG behavior of Al 224-T3 in relation to load ratio, pre strain effects and crack plane orientation. © 2011 Published by Elsevier Ltd.

Constant and variable amplitude fatigue strength of high strength steel welds treated with ultrasonic impact treatment

Hitsattujen rakenteiden väsymiskestävyyttä pystytään parantamaan jälkikäsittelymenetelmillä, joistayksi, ultraäänikäsittely muokkaa hitsin geometriaa ja aiheuttaa puristusjäännösjännitystilan. Tässä tutkimuksessa verrataan kokeellisesti kuormaa kantamattoman hitsatun ja ui -käsitellyn rivan väsymislujuutta toisiinsa. Tutkimusohjelmaan kuuluu kahta teräslajia ja sekä vakio - että vaihtuva - amplitudista kuormitusta. Ultraäänikäsittelyllä saavutetaan väsymiskestoiän parantuminen vakio - ja vaihtuva - amplitudisella kuormituksella. Perusaineen lujuudella ei ole merkittää vaikutusta väsymislujuuteen kun liitos on hitsatussa tilassa. Tällöin väsymiskestävyyden määrää hitsin rajaviivan jännityskeskittymä. Ultraäänikäsitellyn hitsatunliitoksen väsymiskestävyys on suurempi korkeamman lujuuden omaavilla teräksillä. Tästä syystä korkealujuuksisten terästen käyttö ultraäänikäsiteltynä väsyttävästi kuormitetuissa kevytrakenteissa on perusteltua.

Jännityssuhteen vaikutus ultralujan teräksen hitsausliitoksen väsymislujuuteen

Aiempien ultralujia teräksiä koskevien tutkimusten jatkoksi tässä diplomityössä keskityttiin jännityssuhteen varioinnin tuomien ilmiöiden esille tuomiseen koesauvojen väsytyskoestuk-sessa. Pohjana diplomityölle ovat mm. Timo Björkin tutkimustulokset ULTRASTEEL-hankkeesta sekä Tuomas Skrikon kandidaatintyöhönsä koostamat väsytyskoetulokset. Testattujen 12 koesauvan väsytyskoetulosten perusteella jännityssuhteen kasvattaminen alen-taa hitsattujen ultralujien teräsrakenteiden FAT-luokitusta. FAT-luokkien ja jännityssuhteen välillä on havaittu säännönmukaisuutta ja huomattavaa FAT-luokituksen lasku on jännitys-suhteen 0.35 jälkeen. Jälkikäsiteltyjen koesauvojen FAT-luokat ovat jälkikäsittelemättömiä parempia. Myös käsit-telemättömillä sauvoilla päästään mekanisoidussa MAG-hitsauksessa keskimääräisen kone-pajalaadun FAT = 100 MPa yläpuolelle.

Evaluation of WC-10Ni thermal spraying coating by HVOF on the fatigue and corrosion AISI 4340 steel

Shot peening is a surface process widely used to improve the fatigue strength of materials, through compressive residual stresses induced in their surface layers. Considering mechanical components for high responsible applications, wear and corrosion control is currently accomplished by the use of coated materials.In the case of chrome plating or hard anodizing, lower fatigue strength in comparison to uncoated parts are associated to high residual tensile stresses and microcracks density. Under constant or variable amplitude loading microcracks will propagate and cross the interface coating substrate without impediment.The aim of the present study is to analyze the influence of WC-10Ni coating applied by HVOF process on the axial fatigue strength of AISI 4340 steel. The shot peening effect on the fatigue performance of coated AISI 4340 steel was also evaluated. The fractured fatigue specimens were investigated using a scanning electron microscope in order to obtain information about the crack initiation points. (C) 2010 Published by Elsevier Ltd.

Effects of electroplated zinc-nickel alloy coatings on the fatigue strength of AISI 4340 high strength steel

It is well known that fatigue behaviour is an important parameter to be considered in mechanical components subjected to constant and variable amplitude loadings. In combination with corrosion phenomenon, fatigue effects were responsible for proximally 64% of fails that occur in metallic parts of aeronautical accidents in the last 30 years. Recovered substrates have been extensively used in the aerospace field. Cadmium electroplating has been widely applied to promote protective coatings in aeronautical components, resulting in excellent corrosion protection combined with a good performance in cyclic loading. Ecological considerations allied to the increasing demands for corrosion resistance, resulted in the search for possible alternatives. Zinc-nickel alloys received considerable interest recently, since these coatings showed some advantages such as a good resistance to white and red rust, high plating rates and acceptation in the market. In this study the effects of zinc-nickel coatings electroplated on AISI 4340 high strength steel were analysed on rotating bending and axial fatigue strength, corrosion and adhesion resistance. Compressive residual stress field was measured by a X-ray tensometry prior to fatigue tests. Optical microscopy images showed coating thicknesses, adhesion and the existence of an uniform coverage of nearly all substrates. The fractured fatigue specimens were investigated using a scanning electron microscope. Three different zinc-nickel coating thicknesses were tested and comparison with rotating bending fatigue data from specimens cadmium electroplated and heat treated at 190°C for 3, 8 and 24 hours to avoid the diffusion of hydrogen in the substrate, was performed. Experimental results showed effect of coatings on the AISI 4340 steel behaviour when submitted to fatigue testing and the existence of coating thickness influence on the fatigue strength.

Fatigue apparatus for geometrically complex non-standardized specimens

Standard Test Methods (e.g. ASTM, DIN) for materials characterization in general, and for fatigue in particular, do not contemplate specimens with complex geometries, as well as the combination of axial and in-plane bending loads in their methodologies. The present study refers to some patents and the new configuration or configurations of specimens (non-standardized by the status quo of test methods) and a device developed to induce axial and bending combined forces resultants from axial loads applied by any one test equipment (dynamic or monotonic) which possesses such limitation, towards obtaining more realistic results on the fatigue behavior, or even basic mechanical properties, from geometrically complex structures. Motivated by a specific and geometrically complex aeronautic structure (motor-cradle), non-standardized welded tubular specimens made from AISI 4130 steel were fatigue-tested at room temperature, by using a constant amplitude sinusoidal load of 20 Hz frequency, load ratio R = 0.1 with and without the above referred auxiliary fatigue apparatus. The results showed the fatigue apparatus was efficient for introducing higher stress concentration factor at the welded specimen joints, consequently reducing the fatigue strength when compared to other conditions. From the obtained results it is possible to infer that with small modifications the proposed apparatus will be capable to test a great variety of specimen configurations such as: squared tubes and plates with welded or melted junctions, as well as other materials such as aluminum, titanium, composites, polymeric, plastics, etc. © 2009 Bentham Science Publishers Ltd.

Estudo da propagação de trinca por fadiga sob carregamento de amplitude variável

For engineering projects that require high reliability levels, is often not enough know only physical and chemical material properties. It’s necessary understand the failure mode of these materials in operation to ensure security level in the project and establish more stringent criteria in the analysis of structural integrity. Due to this need, aircraft industry has been using aluminum alloys in their designs and projects. “Currently more than 70% of aircraft structures are built of high strength aluminum alloys among which stand out 7075-T6 and 2024-T3 alloys, which are considered basics for being used in the new alloys development.” (PASTOUKHOV & VOORWALD, 1995). Some years ago ALCOA develops Al 2524 alloy that has emerged as refinement of Al 2024 (Al, Cu. Mg) alloy, with purpose of improve fracture toughness and fatigue resistance on structural components. The present research addresses testing of fatigue crack propagation under variable amplitude loading for Al 2024 alloy, observing the interaction effects from application of overhead blocks and plastic zone at the crack tip and makes an analysis of fracture surface images

Estudo do efeito de pausas introduzidas em testes de fadiga de amplitude variável.

É muito importante para a indústria fornecer produtos competitivos e que exerçam corretamente as suas funções perante o cliente. Uma das ferramentas existentes para atingir estes objetivos é a realização de testes de fadiga e durabilidade cada vez mais refinados e em espaço mais curto de tempo. Uma das maneiras de se executar testes de fadiga mais precisos é utilizando parâmetros que sejam fiéis à solicitação que o produto sofre durante o seu uso. Com esse intuito surgiram os testes de fadiga sob amplitude variável. Juntamente com eles surgem as particularidades deste tipo de solicitação, que é de natureza complexa. Algumas particularidades são a dependência do resultado na história de carregamento (também chamada de \"interação de cargas\") e a variação abrupta do nível de carga durante o tempo de aplicação. Fenômenos estes chamados de sobrecarga ou subcarga (overload e underload), que aqui serão agrupados, muitas vezes de forma simplista, de perturbações no espectro de fadiga. A finalidade principal deste trabalho é descrever a influência das perturbações ocorridas nas solicitações nos testes de fadiga em regime de amplitude variável, mais precisamente em testes de bancada, em que se busca a reprodução de situações de trabalho reais de um componente. Apesar de esse assunto ser alvo de diversas investigações recentes, nenhum trabalho tem como foco a influência das paradas (completa remoção de carga) realizadas durante um teste de fadiga acelerado. Essas paradas são extremamente comuns na prática laboratorial, seja por manutenção do equipamento, inspeção da amostra ou necessidade de operação. O objeto alvo de estudo nesta pesquisa é um suporte metálico de buzina, utilizado em automóveis de passeio. Apesar de sua concepção simples, tal componente é responsável por exercer funções importantes e é sujeito a uma interessante gama de solicitações. Como resultado observou-se que a aplicação das paradas durante os testes de fadiga simulados no componente automotivo, provoca variações em sua vida útil total. E o tempo de parada também exerce influência nesta variação observada. Essas paradas não se encaixam perfeitamente nas classificações de perturbações no espectro registradas na literatura. Por esse motivo o trabalho se propõe ainda a sintetizar e uniformizar a terminologia para as variações abruptas de tensão aplicadas no tempo (as sobrecargas e as subcargas), tendo em vista que ocorre a falta de consenso entre os termos utilizados atualmente na literatura e seus respectivos conceitos.

Sviluppo e applicazione di nuovi criteri per la verifica a fatica multiassiale di componenti strutturali in leghe di acciaio e alluminio

La presente Tesi ha per oggetto lo sviluppo e la validazione di nuovi criteri per la verifica a fatica multiassiale di componenti strutturali metallici . In particolare, i nuovi criteri formulati risultano applicabili a componenti metallici, soggetti ad un’ampia gamma di configurazioni di carico: carichi multiassiali variabili nel tempo, in modo ciclico e random, per alto e basso/medio numero di cicli di carico. Tali criteri costituiscono un utile strumento nell’ambito della valutazione della resistenza/vita a fatica di elementi strutturali metallici, essendo di semplice implementazione, e richiedendo tempi di calcolo piuttosto modesti. Nel primo Capitolo vengono presentate le problematiche relative alla fatica multiassiale, introducendo alcuni aspetti teorici utili a descrivere il meccanismo di danneggiamento a fatica (propagazione della fessura e frattura finale) di componenti strutturali metallici soggetti a carichi variabili nel tempo. Vengono poi presentati i diversi approcci disponibili in letteratura per la verifica a fatica multiassiale di tali componenti, con particolare attenzione all'approccio del piano critico. Infine, vengono definite le grandezze ingegneristiche correlate al piano critico, utilizzate nella progettazione a fatica in presenza di carichi multiassiali ciclici per alto e basso/medio numero di cicli di carico. Il secondo Capitolo è dedicato allo sviluppo di un nuovo criterio per la valutazione della resistenza a fatica di elementi strutturali metallici soggetti a carichi multiassiali ciclici e alto numero di cicli. Il criterio risulta basato sull'approccio del piano critico ed è formulato in termini di tensioni. Lo sviluppo del criterio viene affrontato intervenendo in modo significativo su una precedente formulazione proposta da Carpinteri e collaboratori nel 2011. In particolare, il primo intervento riguarda la determinazione della giacitura del piano critico: nuove espressioni dell'angolo che lega la giacitura del piano critico a quella del piano di frattura vengono implementate nell'algoritmo del criterio. Il secondo intervento è relativo alla definizione dell'ampiezza della tensione tangenziale e un nuovo metodo, noto come Prismatic Hull (PH) method (di Araújo e collaboratori), viene implementato nell'algoritmo. L'affidabilità del criterio viene poi verificata impiegando numerosi dati di prove sperimentali disponibili in letteratura. Nel terzo Capitolo viene proposto un criterio di nuova formulazione per la valutazione della vita a fatica di elementi strutturali metallici soggetti a carichi multiassiali ciclici e basso/medio numero di cicli. Il criterio risulta basato sull'approccio del piano critico, ed è formulato in termini di deformazioni. In particolare, la formulazione proposta trae spunto, come impostazione generale, dal criterio di fatica multiassiale in regime di alto numero di cicli discusso nel secondo Capitolo. Poiché in presenza di deformazioni plastiche significative (come quelle caratterizzanti la fatica per basso/medio numero di cicli di carico) è necessario conoscere il valore del coefficiente efficace di Poisson del materiale, vengono impiegate tre differenti strategie. In particolare, tale coefficiente viene calcolato sia per via analitica, che per via numerica, che impiegando un valore costante frequentemente adottato in letteratura. Successivamente, per validarne l'affidabilità vengono impiegati numerosi dati di prove sperimentali disponibili in letteratura; i risultati numerici sono ottenuti al variare del valore del coefficiente efficace di Poisson. Inoltre, al fine di considerare i significativi gradienti tensionali che si verificano in presenza di discontinuità geometriche, come gli intagli, il criterio viene anche esteso al caso dei componenti strutturali intagliati. Il criterio, riformulato implementando il concetto del volume di controllo proposto da Lazzarin e collaboratori, viene utilizzato per stimare la vita a fatica di provini con un severo intaglio a V, realizzati in lega di titanio grado 5. Il quarto Capitolo è rivolto allo sviluppo di un nuovo criterio per la valutazione del danno a fatica di elementi strutturali metallici soggetti a carichi multiassiali random e alto numero di cicli. Il criterio risulta basato sull'approccio del piano critico ed è formulato nel dominio della frequenza. Lo sviluppo del criterio viene affrontato intervenendo in modo significativo su una precedente formulazione proposta da Carpinteri e collaboratori nel 2014. In particolare, l’intervento riguarda la determinazione della giacitura del piano critico, e nuove espressioni dell'angolo che lega la giacitura del piano critico con quella del piano di frattura vengono implementate nell'algoritmo del criterio. Infine, l’affidabilità del criterio viene verificata impiegando numerosi dati di prove sperimentali disponibili in letteratura.

Optical correlation by use of partial phase-only modulation with VGA liquid-crystal displays

The development of liquid-crystal panels for use in commercial equipment has been aimed at improving the pixel resolution and the display efficiency. These improvements have led to a reduction in the thickness of such devices, among other outcomes, that involves a loss in phase modulation. We propose a modification of the classical phase-only filter to permit displays in VGA liquid-crystal panels with a constant amplitude modulation and less than a 2¿(PI) phase modulation. The method was tested experimentally in an optical setup.

A Continuous Span Aluminum Girder Concrete Deck Bridge - Part 2 of 2: Fatigue Tests of Aluminum Girders, Final Report, 1997

In 1957, the Iowa State Highway Commission, with financial assistance from the aluminum industry, constructed a 220-ft (67-m) long, four-span continuous, aluminum girder bridge to carry traffic on Clive Road (86th Street) over Interstate 80 near Des Moines, Iowa. The bridge had four, welded I-shape girders that were fabricated in pairs with welded diaphragms between an exterior and an interior girder. The interior diaphragms between the girder pairs were bolted to girder brackets. A composite, reinforced concrete deck served as the roadway surface. The bridge, which had performed successfully for about 35 years of service, was removed in the fall of 1993 to make way for an interchange at the same location. Prior to the bridge demolition, load tests were conducted to monitor girder and diaphragm bending strains and deflections in the northern end span. Fatigue testing of the aluminum girders that were removed from the end spans were conducted by applying constant-amplitude, cyclic loads. These tests established the fatigue strength of an existing, welded, flange-splice detail and added, welded, flange-cover plates and horizontal web plate attachment details. This part, Part 2, of the final report focuses on the fatigue tests of the aluminum girder sections that were removed from the bridge and on the analysis of the experimental data to establish the fatigue strength of full-size specimens. Seventeen fatigue fractures that were classified as Category E weld details developed in the seven girder test specimens. Linear regression analyses of the fatigue test results established both nominal and experimental stress-range versus load cycle relationships (SN curves) for the fatigue strength of fillet-welded connections. The nominal strength SN curve obtained by this research essentially matched the SN curve for Category E aluminum weldments given in the AASHTO LRFD specifications. All of the Category E fatigue fractures that developed in the girder test specimens satisfied the allowable SN relationship specified by the fatigue provisions of the Aluminum Association. The lower-bound strength line that was set at two standard deviations below the least squares regression line through the fatigue fracture data points related well with the Aluminum Association SN curve. The results from the experimental tests of this research have provided additional information regarding behavioral characteristics of full-size, aluminum members and have confirmed that aluminum has the strength properties needed for highway bridge girders.

Väsymismitoitusperusteiden ja kuormitusten määrittäminen hitsatuille sekoitinakseleille

Työssä selvitettiin vastusvenymäliuskamittausten avulla sekoitinakselin kuormitukset sekä perehdyttiin väsymisilmiöön ja hitsattujen rakenteiden väsymismitoitukseen. Kuormitusten mittauksessa rekisteröitiin akselin kriittisen kohdan taivutus- ja vääntövenymät. Mittaustulosten avulla tutkittiin kuormituksia ja kuormitusten luonnetta sekä johdettiin väsymismitoitusperusteet sekoitinakseleille. Väsymismitoitus perustuu kahteen eri menetelmään. Vakioamplitudiseen väsymisrajaan perustuvassa menetelmässä vaihtuva-amplitudisella jännityksellä suurinkin jännitysheilahdus jää väsymisrajan alle. Kokonaisväsymisvaurioon perustuvassa mitoituksessa puolestaan sallitaan vakioamplitudisen väsymisrajan ylitys. Kestoikä on käytetty loppuun, kun väsymisvaurio saavuttaa väsymiskestävyyden arvon. Menetelmän valinta riippuu käytettävästä sekoitinelintyypistä ja käytön aikana ilmenevistä väsymisen kannalta vaarallisista tilanteista.