Uma proposta de intervenção com professores e os efeitos no repertório comportamental e desempenho acadêmico de seus alunos

Pós-graduação em Psicologia do Desenvolvimento e Aprendizagem - FC

PHOTOELASTIC ANALISYS OF A HUMAN VERTEBRA MODEL WITH PEDICULAR SCREW

Introduction: The vertebrae fixation system using pedicular screws is one of the most efficient methods to treat vertebral spine pathologies. When the screw is submitted to pullout strength, it causes internal tension near the medullar canal and this situation can be analyzed by using the photoelasticity technique. Objective: Were analyzed those internal tensions near the medullar canal of photoelastic vertebra models using different sizes of screws of the vertebral fixation system submitted to pullout strength. Methods: A lumbar vertebral model made of photoelastic material with three different USS1-type pedicular screw sizes (5, 6, and 7 mm) was used. The internal tensions around the screw were tested in 12 predetermined points by a plain transmission polaroscope. Results: The areas of greater tension concentration were between the medullar canal and the curves of the transverse process. Comparing the maximum average pulling tension, statistical differences were observed between screws 5 and 7, and 6 and 7. On the other hand, for screws 5 and 6, there were no significant differences. Conclusion: The study evidenced that the internal tensions are greater in irregular areas, next to the medullar canal, showing that this is a critical region.

THE PHOTOELASTIC ANALISYS OF VERTEBRAL FIXATION SYSTEM SCREWS

Introduction: The photoelasticity is used for assessing the tensions/deformations involved in photoelastic materials when submitted to a given load by the observation of optical effects. The screw performance and mechanical functions are directly associated to the quality of the screws fixation in the vertebrae. Photoelasticity is an important tool to perform comparative studies of this nature. Objective: The aim of this study was to compare, by using photoelasticity, internal stresses produced by the screw with an external diameter of 6 mm, when submitted to two different pullout strengths. Materials and Methods: For this, four photoelastic models were produced. The simulation was conducted by using two pullout strengths: 0.75 and 1.50 kgf. The maximum shear stresses were calculated on 19 points around the screws, using the Tardy compensation method. Results:The values of maximum shear stress were higher with the load of 1.50 kgf. Conclusion: Thus, the screw will be more susceptible to pullout when heavier loads are applied. According to our analysis, we also found that the site with the highest maximum shear stress was found to be at the peak of creast, particularly near the tips of the screws, regardless of the load employed.

Conduct after Epley`s maneuver in elderly with posterior canal BPPV in the posterior canal

Benign Paroxysmal Positional Vertigo is the most common peripheral vestibular disorder, especially in the elderly and presents as the predominant etiology in this population of the degeneration of the utricular macula. Aim: To compare the effectiveness of the approaches after Epley maneuver. Study Design: longitudinal cohort. Materials and Methods: The study included 53 volunteers with Benign Paroxysmal Positional Vertigo of the posterior semicircular canal, divided into Group 1, who underwent Epley maneuver associated with the use of neck collar and post-maneuver instructions, Group 2 underwent the Epley maneuver without the use cervical collar and/or post-maneuver restrictions, and Group 3 underwent the Epley maneuver associated with the use of a mini vibrator, without the use of neck collar and/or post-maneuver restrictions. Results: In the three groups, the number of Epley maneuvers ranged from one to three. We employed the Brazilian Dizziness Handicap Inventory - pre- and post-treatment and observed a statistically significant difference on most scores pre- and post-treatment for both groups. Conclusion: Regardless of the post Epley maneuver treatment selected for the treatment of Benign Paroxysmal Positional Vertigo, it was effective when comparing the Brazilian Dizziness Handicap Inventory pre- and post-treatment.

Credibility and staff conduct make or break bank customer service quality

Service quality is assessed by customers along the dimensions of staff conduct, credibility, communication, and access to teller services. Credibility and staff conduct emerge as the highest loading first-order factors. This highlights the significance of rectifying mistakes while keeping customers informed, and employing branch staff that are responsive and civilized in their conduct. Discovery of a valid second-order factor, namely, overall customer service quality, underscores the importance of providing quality service across all its dimensions. For example, if the bank fails to rectify mistakes and keep customers informed but excels in all other dimensions, its overall customer service quality can still be rated poorly.

Effects of paternal drinking, conduct disorder and childhood home environment on the development of alcohol use disorders in a Thai population

Aims To identify influences on the development of alcohol use disorders in a Thai population, particularly parental drinking and childhood environment. Design Case-control study. Setting A university hospital, a regional hospital and a community hospital in southern Thailand. Participants Ninety-one alcohol-dependents and 177 hazardous/harmful drinkers were recruited as cases and 144 non-or infrequent drinkers as controls. Measurements Data on parental drinking, family demographic characteristics, family activities, parental disciplinary practice, early religious life and conduct disorder were obtained using a structured interview questionnaire. The main outcome measure was the subject's classification as alcohol-dependent, hazardous/harmful drinker or non-/infrequent drinker. Findings A significant relationship was found between having a drinking father and the occurrence of hazardous/harmful drinking or alcohol dependence in the subjects. Childhood factors (conduct disorder and having been a temple boy, relative probability ratios, RPRs and 95% CI: 6.39, 2.81-14.55 and 2.21, 1.19-4.08, respectively) also significantly predicted alcohol dependence, while perceived poverty and ethnic alienation was reported less frequently by hazardous/harmful drinkers and alcohol-dependents (RPRS and 95% CIs = 0.34, 0.19-0.62 and 0.59, 0.38-0.93, respectively) than the controls. The relative probability ratio for the effect of the father's infrequent drinking on the son's alcohol dependence was 2.92 (95% CI = 1.42-6.02) and for the father's heavy or dependent drinking 2.84 (95% CI=1.31-6.15). Conclusions Being exposed to a light-drinking, father increases the risk of a son's alcohol use disorders exhibited either as hazardous-harmful or dependent drinking. However, exposure to a heavy- or dependent-drinking father is associated more uniquely with an increased risk of his son being alcohol-dependent. The extent to which this is seen in other cultures is worthy of exploration.

Aboriginal and Torres Strait Islander health research and the conduct of longitudinal studies: issues for debate

The National Health and Medical Research Council, Research Agenda Working Group (RAWG), and the literature on Indigenous health have identified the need to fill gaps in descriptive data on Aboriginal and Torres Strait Islander health and noted both the lack of research with urban populations and the need for longitudinal studies. This paper presents some of the broad ethical and methodological challenges associated with longitudinal research in Indigenous health and focuses particularly on national studies and studies in urban areas. Our goal is to advance debate in the public health arena about the application of ethical guidelines and the conduct of longitudinal studies in Aboriginal and Torres Strait Islander communities. We encourage others to offer their experiences in this field.

Surface plasmon resonance as a tool in the functional analisys of an immunodominant site in foot-and-mouth disease virus

A fast and direct surface plasmon resonance (SPR) method for the kinetic analysis of the interactions between peptide antigens and immobilised monoclonal antibodies (mAb) has been established. Protocols have been developed to overcome the problems posed by the small size of the analytes (< 1600 Da). The interactions were well described by a simple 1:1 bimolecular interaction and the rate constants were self-consistent and reproducible. The key features for the accuracy of the kinetic constants measured were high buffer flow rates, medium antibody surface densities and high peptide concentrations. The method was applied to an extensive analysis of over 40 peptide analogues towards two distinct anti-FMDV antibodies, providing data in total agreement with previous competition ELISA experiments. Eleven linear 15-residue synthetic peptides, reproducing all possible combinations of the four replacements found in foot-and-mouth disease virus (FMDV) field isolate C-S30, were evaluated. The direct kinetic SPR analysis of the interactions between these peptides and three anti-site A mAbs suggested additivity in all combinations of the four relevant mutations, which was confirmed by parallel ELISA analysis. The four-point mutant peptide (A15S30) reproducing site A from the C-S30 strain was the least antigenic of the set, in disagreement with previously reported studies with the virus isolate. Increasing peptide size from 15 to 21 residues did not significantly improve antigenicity. Overnight incubation of A15S30 with mAb 4C4 in solution showed a marked increase in peptide antigenicity not observed for other peptide analogues, suggesting that conformational rearrangement could lead to a stable peptide-antibody complex. In fact, peptide cyclization clearly improved antigenicity, confirming an antigenic reversion in a multiply substituted peptide. Solution NMR studies of both linear and cyclic versions of the antigenic loop of FMDV C-S30 showed that structural features previously correlated with antigenicity were more pronounced in the cyclic peptide. Twenty-six synthetic peptides, corresponding to all possible combinations of five single-point antigenicity-enhancing replacements in the GH loop of FMDV C-S8c1, were also studied. SPR kinetic screening of these peptides was not possible due to problems mainly related to the high mAb affinities displayed by these synthetic antigens. Solution affinity SPR analysis was employed and affinities displayed were generally comparable to or even higher than those corresponding to the C-S8c1 reference peptide A15. The NMR characterisation of one of these multiple mutants in solution showed that it had a conformational behaviour quite similar to that of the native sequence A15 and the X-ray diffraction crystallographic analysis of the peptide ? mAb 4C4 complex showed paratope ? epitope interactions identical to all FMDV peptide ? mAb complexes studied so far. Key residues for these interactions are those directly involved in epitope ? paratope contacts (141Arg, 143Asp, 146His) as well as residues able to stabilise a particular peptide global folding. A quasi-cyclic conformation is held up by a hydrophobic cavity defined by residues 138, 144 and 147 and by other key intrapeptide hydrogen bonds, delineating an open turn at positions 141, 142 and 143 (corresponding to the Arg-Gly-Asp motif).

Aplicação do Método SFA (Safety Function Analisys) a um. Posto de Transformação de Energia Eléctrica da Renova

Riscos Industriais e Emergentes, 2009 pp. 827-844

Industrial networks: are they a new and alternative way to conduct business or just a logical consequence of a globalising economy?

Based on a report for the seminar Industrial Networks, at Goethe Universität Frankfurt am Main Dozent: Prof. Dr. Blättel-Mink, Prof. Dr. António Moniz SS 2011

Using mobile technology to conduct epidemiological investigations

INTRODUCTION : The aim of this study was to report the experience of an epidemiological field survey for which data were collected and analyzed using tablets. METHODS : The devices used Epi Info 7 (Android version), which has been modeled a database with variables of the traditional form. RESULTS : Twenty-one households were randomly selected in the study area; 75 residents were registered and completed household interviews with socioeconomic and environmental risk variables. CONCLUSIONS : This new technology is a valuable tool for collecting and analyzing data from the field, with advantageous benefits to epidemiological surveys.

Hypertensive diabetic patients: guidelines for conduct and their difficulties

OBJECTIVE: To assess the effect of blood pressure (BP) control and other cardiovascular risk factors in patients with diabetes mellitus in a referral service for the treatment of hypertension. METHODS: A retrospective study where diabetic patients (at least 2 fasting glucose levels above 126 mg/dL, use of hypoglycemic agents or insulin, or both of these) were included. They were evaluated at the first appointment (M1) and at the last appointment (M2), regarding blood pressure, body mass index (BMI), use of hypertensive drugs, glycemia, total cholesterol (TC), creatinine, and potassium. RESULTS: Of 1,032 patients studied, 146 patients with a mean age of 61.6 years had diabetes, and 27 were men (18.5%). Mean follow-up was 5.5 years. BP values were 161.6 x 99.9 mmHg in M1 and 146.3 x 89.5 mmHg in M2. In M1, 10.4% of the patients did not use medications, 50.6% used just 1 drug, 30.8% used 2 drugs, and 8.2% used 3 or more drugs. In M2, these values were 10.9%, 39%, 39.7%, and 10.4%, respectively. Diuretics were the most commonly used medication, whereas angiotensin-converting enzyme inhibitors (ACE inhibitors) were those drugs which presented greater increase when comparing M1 to M2 (24.6% and 41.7%, respectively). Only 17,1% reached the recommended goal (BP<130x85 mmhg). The other cardiovascular risk factors did not change significantly. CONCLUSION: Our data reinforce the necessity of a more aggressive approach in the treatment of these patients, despite the social and economic difficulties in adhering to treatment.

Rol de las metaloproteasas y caspasas en la conducta biológica del carcinoma basocelular. Role of the metalloproteinases and caspasa Biology in the conduct of basal cell carcinoma.

El carcinoma basocelular (CBC) representa el tumor maligno más frecuente de la piel en personas de raza blanca. Incide en mayores de 50 años de edad e infiltra los tejidos, pero rara vez ocasiona metástasis. En trabajos anteriores, observamos imágenes de cuerpos apoptóticos con MOAR (microscopía óptica de alta resolución), en pieles portadoras de CBC. Todas las células eucariotas poseen una maquinaria enzimática que interviene en la apoptosis. Estas enzimas son las proteincinasas pertenecientes a la familia de las caspasas. Se sintetizan como procaspasas, las cuales una vez activadas, actúan sobre otra caspasa en una reacción secuencial en cadena. Se reconoce que la apoptosis juega un rol importante en el balance y mantenimiento de los tejidos. Hipótesis: -Investigar si la expresión de metaloproteasas y caspasas en las células del CBC promueven y contribuyen a la progresión y extensión tumoral. Objetivos:-Profundizar el conocimiento de la conducta biológica del CBC, en referencia a la relación de los patrones de crecimiento macro y microscópicos del tumor, enfatizando en la expresión de metaloproteasas (colagenasa-3 y streptomelisina), CD-31, Ki-67, oncoproteína bcl-2 y caspasas, mediante la implementación de técnicas de inmunohistoquímica. -Analizar a nivel morfológico la presencia de cuerpos apoptóticos por medio de MOAR y determinar si influyen en la conducta biológica del tumor. Materiales y Métodos: Se realizará un estudio retrospectivo y prospectivo de pacientes asistidos en el Servicio de Dermatología del Hospital Nacional de Clínicas, desde el año 2000. Se utilizarán tomas incisionales de piel, que se fijarán en formol neutro al 10 por ciento y luego serán procesadas e incluidas en parafina y coloreadas con H-E (hematoxilina-eosina). Especimenes seleccionados, se utilizarán para técnicas de MOAR e inmunocitoquímica. El material para MOAR, se fijará en Karnovsky enfriado a pH 7,2 y se incluirá en resinas epóxicas, seccionados con un ultramicrótomo Porter BluMT1 (1micra) y coloreados con P.A.S. azul de toluidina, fuscina básica y metenamina-plata. La aplicación de las técnicas inmunohistoquímicas, se utilizaran sobre cortes desparafinados con xilol, que permitirán investigar en forma retrospectiva y prospectiva la matriz extracelular (MEC) y los elementos neoplásicos. Los anticuerpos monoclonales a utilizar serán: Colageno tipo IV clone CIV 22 M0785 monoclonal antibody (DAKO), CD44 clone E29 M0613 monoclonal antibody (DAKO), Oncoproteina bcl-2 clone 124 M0887 monoclonal antibody (DAKO), CD31: clone 35 BH11 MO631 monoclonal antibody (DAKO) K-167 clone PC10 M0879 monoclonal antibody.(DAKO) bclx y Caspasa 8. Metodología Estadística Los resultados serán evaluados mediante: a) Varianza Anova; para datos con distribución gausiana como media, SD. b) Krusal Walles; para rasgos de distribución no gausiana. c) Chi2 para determinar la diferencia significativa para proporciones. Resultados esperados: Del análisis histomorfológico cualitativo y cuantitativo de biopsias de piel con CBC, aportar determinaciones que clarifiquen la conducta biológica de este tumor.- Importancia del Proyecto: El CBC es una entidad que está aumentando su incidencia en forma exponencial, debido sobre todo a pautas sociales. No sólo ocasiona trastornos en los pacientes, sino que también, representa gastos en el sistema de salud. Asimismo, significa un desafío para la investigación. Esto permite explorar aspectos de la biología molecular, a partir de una entidad que posee características únicas.