Colisões periféricas de íons pesados

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Supressão de J/[psi] em processos próton-núcleo e núcleo-núcleo devido aos efeitos de alta densidade

A supressão da produção do méson J/Ψ em colisões de íons pesados tem sido apontada como um sinal da formação de um estado desconfinado da matéria - o Plasma de Quarks e Glúons. Este sinal, por em, não e inequívoco e muitos modelos, que não assumem a formação do plasma, podem descrever igualmente bem os resultados da colaboração NA50, no CERN, que apontou uma supressão anômala, não explicada pela absorção nuclear, nas colisões mais centrais entre íons de chumbo. De modo geral, estes modelos, considerando ou não a formação do plasma, procuram explicar os resultados experimentais através de mecanismos que causam a supressão no estado final da colisão, isto e, mecanismos que agem sobre as partículas produzidas na colisão. Por outro lado, para núcleos pesados e em processos envolvendo altas energias, as distribuições partônicas nucleares são alteradas em relação as distribuições para nucleons livres. Estas alterações ocorrem devido ao fato das dimensões do nucleon serem um limite geométrico para o crescimento das distribuições - seu vínculo de unitariedade - pois o meio nuclear, em altas energias, apresenta uma alta densidade partônica. A existência deste vínculo de unitariedade requer modificações das distribuições partônicas, o que deve ser considerado nos cálculos das seções de choque nucleares. Tais modificações afetam a produção de hádrons no estado final, diminuindo sua taxa de produção. Nesse trabalho, investigamos a inclusão dos efeitos de alta densidade nas distribuições partônicas para o tratamento da supressão de J/Ψ em colisões envolvendo alvos nucleares. Estes efeitos são decorrentes do aumento da distribuição de glúions na região de pequeno x (altas energias). A evolução DGLAP, que considera apenas a emissão de pártons, prevê um crescimento ilimitado da distribuição de glúons nesta região, quebrando assim o vínculo da unitariedade. Por isso, o mecanismo de recombinação partônica passa a contribuir para restaurar a unitariedade. Estes efeitos de recombinação, basicamente, são tratados como os efeitos de alta densidade referidos nesse trabalho, alterando as distribuições partônicas nucleares. Utilizamos processos próton-núcleo para estimar a magnitude destes efeitos, uma vez que estes processos não apresentam um meio nuclear tão denso quanto o proporcionado por colisões núcleo-núcleo. Esta premissa torna os processos próton-núcleo testes mais confiaveis para a investigação dos efeitos de alta densidade. Analisamos em especial a razão entre as taxas de produção do méson J/Ψ e do par de léptons, via processo Drell- Yan, uma vez que este observável e utilizado para apontar a supressão na produção de J/Ψ . Estendemos esta análise para processos núcleo-núcleo, onde novos mecanismos de supressão, entre eles a formação do Plasma de Quarks e Glúons são esperados. Os resultados aqui apresentados mostram que a inclusão dos efeitos de alta densidade introduz uma supressão adicional na produção de J/Ψ , que se torna mais significativa com o aumento da energia do processo. Nossa conclusão e, portanto, que estes efeitos devem ser incorporados na análise deste sinal em experimentos realizados em RHIC e LHC.

Dinâmica das transições quiral e de desconfinamento da cromodinâmica quântica com o modelo Polyakov-Nambu-Jona-Lasinio

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeitos de alta densidade em processos Drell-Yan de altas energias

Um dos problemas teóricos mais importantes da Física de Partículas de Altas Energias é a investigação de efeitos de alta densidade na Cromodinâmica Quântica (QCD), que é a teoria que descreve as interações fortes. Tais efeitos são importantes pois determinam os observáveis em colisõesde altas energias. Em processos hadrônicos de energia suficientemente alta, espera-se a formação de sistemas densos o suficiente para que efeitos não lineares de QCD passem a ser significativos na descrição e na unitarização da seção de choque. Na descrição de processos de espalhamento de altas energias, evidências experimentais indicam que os hádrons são constituídos por partículas puntuais, as quais chamamos de pártons. Os pártons carregam uma fração x do momentum total do hádron, e são de dois tipos, quarks e glúons. Na interação entre as partículas ocorre a troca de momentum, definida como Q2. A descrição perturbativa padrão para a evolução dinâmica das distribuições de quarks q(x, Q2) e glúons g(x, Q2), pode ser dada pelas equações de evolução DGLAP, e tem obtido sucesso na descrição dos resultados experimentais para as presentes energias. Na evolução DGLAP, são considerados apenas processos de emissão, como a emissão de um glúon por um quark, o decaimento de um glúon em um par de quarks ou em um par de glúons Estes processos de emissão tendem a aumentar a densidade de pártons na região de pequeno momentum, levando a um crescimento ilimitado das distribuições partônicas para x -+ O. Assim, é esperado que o crescimento da densidade de pártons leve a interação e recombinação destas partículas, dando origem a termos não lineares nas equações de evolução. O resultado seria um processo de saturação das distribuições de pártons na região de alta energia e pequena fração de momentum. Os efeitos que dão origem à redução do crescimento das distribuições de quarks e glúons em relação a evolução linear são chamados genericamente de efeitos de sombreamento. Um dos aspectos fenomenológicosinteressantes a ser investigado no regime cinemático abordado acima é o processo Drell-Yan de alta energia, o qual consiste em processos de espalhamento pp, pA e AA com a produção de pares de léptons. Com o advento dos novos aceleradores, novos resultados experimentais estarão disponíveis na literatura relacionados com este processo. Em nosso trabalho investigamos os efeitos das correções de unitariedade em processos pp, bem como os efeitos devido a presença do meio nuclear em colisõespA e AA, nas distribuições de quarks e glúons, para a descrição da seção de choque diferencial para o processo Drell-Yan em colisõespp, pA e AA, para energias existentes nos novos aceleradores RHIC (Relativistic Heavy Ion Collider) e LHC (Large Ion Collider). Os efeitos de alta densidade são baseados no formalismo de Glauber-Mueller. Os resultados aqui apresentados mostram que os efeitos de alta densidade nas distribuições partônicas são importantes para altas energias, pois a descrição da seção de choque para o processo Drell-Yan, quando os efeitos de alta densidade são considerados, apresenta significativas diferenças da descrição onde não considera-se tais efeitos.

Drag force in a strongly coupled anisotropic plasma

We calculate the drag force experienced by an in finitely massive quark propagating at constant velocity through an anisotropic, strongly coupled N = 4 plasma by means of its gravity dual. We find that the gluon cloud trailing behind the quark is generally misaligned with the quark velocity, and that the latter is also misaligned with the force. The drag coefficient mu can be larger or smaller than the corresponding isotropic value depending on the velocity and the direction of motion. In the ultra-relativistic limit we find that generically mu proportional to p. We discuss the conditions under which this behaviour may extend to more general situations.

Jet quenching in a strongly coupled anisotropic plasma

The jet quenching parameter of an anisotropic plasma depends on the relative orientation between the anisotropic direction, the direction of motion of the parton, and the direction along which the momentum broadening is measured. We calculate the jet quenching parameter of an anisotropic, strongly coupled N = 4 plasma by means of its gravity dual. We present the results for arbitrary orientations and arbitrary values of the anisotropy. The anisotropic value can be larger or smaller than the isotropic one, and this depends on whether the comparison is made at equal temperatures or at equal entropy densities. We compare our results to analogous calculations for the real-world quark-gluon plasma and find agreement in some cases and disagreement in others.

Measurement of electrons from heavy-flavour hadron decays in p-Pb collisions at $\\sqrt{s_{NN}} = 5.02$ TeV using TPC and EMCal detectors with ALICE at LHC

Heavy-ion collisions are a powerful tool to study hot and dense QCD matter, the so-called Quark Gluon Plasma (QGP). Since heavy quarks (charm and beauty) are dominantly produced in the early stages of the collision, they experience the complete evolution of the system. Measurements of electrons from heavy-flavour hadron decay is one possible way to study the interaction of these particles with the QGP. With ALICE at LHC, electrons can be identified with high efficiency and purity. A strong suppression of heavy-flavour decay electrons has been observed at high $p_{m T}$ in Pb-Pb collisions at 2.76 TeV. Measurements in p-Pb collisions are crucial to understand cold nuclear matter effects on heavy-flavour production in heavy-ion collisions. The spectrum of electrons from the decays of hadrons containing charm and beauty was measured in p-Pb collisions at $\\sqrt = 5.02$ TeV. The heavy flavour decay electrons were measured by using the Time Projection Chamber (TPC) and the Electromagnetic Calorimeter (EMCal) detectors from ALICE in the transverse-momentum range $2 < p_ < 20$ GeV/c. The measurements were done in two different data set: minimum bias collisions and data using the EMCal trigger. The non-heavy flavour electron background was removed using an invariant mass method. The results are compatible with one ($R_ \\approx$ 1) and the cold nuclear matter effects in p-Pb collisions are small for the electrons from heavy-flavour hadron decays.

Field and laboratory performance evaluation of a field-blended rubber asphalt.

ALICE is one of four major experiments of particle accelerator LHC installed in the European laboratory CERN. The management committee of the LHC accelerator has just approved a program update for this experiment. Among the upgrades planned for the coming years of the ALICE experiment is to improve the resolution and tracking efficiency maintaining the excellent particles identification ability, and to increase the read-out event rate to 100 KHz. In order to achieve this, it is necessary to update the Time Projection Chamber detector (TPC) and Muon tracking (MCH) detector modifying the read-out electronics, which is not suitable for this migration. To overcome this limitation the design, fabrication and experimental test of new ASIC named SAMPA has been proposed . This ASIC will support both positive and negative polarities, with 32 channels per chip and continuous data readout with smaller power consumption than the previous versions. This work aims to design, fabrication and experimental test of a readout front-end in 130nm CMOS technology with configurable polarity (positive/negative), peaking time and sensitivity. The new SAMPA ASIC can be used in both chambers (TPC and MCH). The proposed front-end is composed of a Charge Sensitive Amplifier (CSA) and a Semi-Gaussian shaper. In order to obtain an ASIC integrating 32 channels per chip, the design of the proposed front-end requires small area and low power consumption, but at the same time requires low noise. In this sense, a new Noise and PSRR (Power Supply Rejection Ratio) improvement technique for the CSA design without power and area impact is proposed in this work. The analysis and equations of the proposed circuit are presented which were verified by electrical simulations and experimental test of a produced chip with 5 channels of the designed front-end. The measured equivalent noise charge was <550e for 30mV/fC of sensitivity at a input capacitance of 18.5pF. The total core area of the front-end was 2300?m × 150?m, and the measured total power consumption was 9.1mW per channel.

Noise and PSRR improvement technique for TPC readout front-end in CMOS. technology.

ALICE is one of four major experiments of particle accelerator LHC installed in the European laboratory CERN. The management committee of the LHC accelerator has just approved a program update for this experiment. Among the upgrades planned for the coming years of the ALICE experiment is to improve the resolution and tracking efficiency maintaining the excellent particles identification ability, and to increase the read-out event rate to 100 KHz. In order to achieve this, it is necessary to update the Time Projection Chamber detector (TPC) and Muon tracking (MCH) detector modifying the read-out electronics, which is not suitable for this migration. To overcome this limitation the design, fabrication and experimental test of new ASIC named SAMPA has been proposed . This ASIC will support both positive and negative polarities, with 32 channels per chip and continuous data readout with smaller power consumption than the previous versions. This work aims to design, fabrication and experimental test of a readout front-end in 130nm CMOS technology with configurable polarity (positive/negative), peaking time and sensitivity. The new SAMPA ASIC can be used in both chambers (TPC and MCH). The proposed front-end is composed of a Charge Sensitive Amplifier (CSA) and a Semi-Gaussian shaper. In order to obtain an ASIC integrating 32 channels per chip, the design of the proposed front-end requires small area and low power consumption, but at the same time requires low noise. In this sense, a new Noise and PSRR (Power Supply Rejection Ratio) improvement technique for the CSA design without power and area impact is proposed in this work. The analysis and equations of the proposed circuit are presented which were verified by electrical simulations and experimental test of a produced chip with 5 channels of the designed front-end. The measured equivalent noise charge was <550e for 30mV/fC of sensitivity at a input capacitance of 18.5pF. The total core area of the front-end was 2300?m × 150?m, and the measured total power consumption was 9.1mW per channel.

Remoção de metais pesados em efluentes sintéticos utilizando vermiculita como adsorvente

Heavy metals are used in many industrial processestheirs discard can harm fel effects to the environment, becoming a serious problem. Many methods used for wastewater treatment have been reported in the literature, but many of them have high cost and low efficiency. The adsorption process has been used as effective for the metal remoal ions. This paper presents studies to evaluate the adsorption capacity of vermiculite as adsorbent for the heavy metals removal in a synthetic solution. The mineral vermiculite was characterized by differents techniques: specific surface area analysis by BET method, X-ray diffraction, raiosX fluorescence, spectroscopy in the infraredd region of, laser particle size analysis and specific gravity. The physical characteristics of the material presented was appropriate for the study of adsorption. The adsorption experiments weredriveal finite bath metod in synthetic solutions of copper, nickel, cadmium, lead and zinc. The results showed that the vermiculite has a high potential for adsorption, removing about 100% of ions and with removal capacity values about 85 ppm of metal in solution, 8.09 mg / g for cadmium, 8.39 mg/g for copper, 8.40 mg/g for lead, 8.26 mg/g for zinc and 8.38 mg/g of nickel. The experimental data fit in the Langmuir and Freundlich models. The kinetic datas showed a good correlation with the pseudo-second order model. It was conducteas a competition study among the metals using vermiculiti a adsorbent. Results showed that the presence of various metals in solution does not influence their removal at low concentrations, removing approximat wasely 100 % of all metals present in solutions

Estudo de adsorvente obtido de terras diatomáceas para remoção de metais pesados em águas produzidas: processamento, caracterização e dinâmica em leito fixo

The acceleration of industrial growth in recent decades on all continents aroused the interest of the companies to counter the impacts produced on the environment, spurred primarily by major disasters in the petroleum industry. In this context, the water produced is responsible for the largest volume of effluent from the production and extraction of oil and natural gas. This effluent has in its composition some critical components such as inorganic salts, heavy metals (Fe, Cu, Zn, Pb, Cd, ), presence of oil and chemicals added in the various production processes. In response to impact, have been triggered by research alternative adsorbent materials for water treatment and water produced, in order to removing oils and acids and heavy metals. Many surveys of diatomaceous earth (diatomite) in Brazil involve studies on the physico-chemical, mineral deposits, extraction, processing and applications. The official estimated Jazi are around 2.5 million tonnes, the main located in the states of Bahia (44%) and Rio Grande do Norte (37,4%). Moreover, these two states appear as large offshore producers, earning a prominent role in research of adsorbents such as diatomite for treatment of water produced. Its main applications are as an agent of filtration, adsorption of oils and greases, industrial load and thermal insulator. The objective of this work was the processing and characterization of diatomite diatomaceous earth obtained from the municipality of Macaíba-RN (known locally as tabatinga) as a low cost regenerative adsorbent for removal of heavy metals in the application of water produced treatment. In this work we adopted a methodology for batch processing, practiced by small businesses located in producing regions of Brazil. The characterization was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and specific surface area (BET). Research conducted showed that the improvement process used was effective for small volume production of diatomite concentrated. The diatomite obtained was treated by calcination at temperature of 900 oC for 2 hours, with and without fluxing Na2CO3 (4%), according to optimal results in the literature. Column adsorption experiments were conducted to percolation of the in nature, calcined and calcined fluxing diatomites. Effluent was used as a saline solution containing ions of Cu, Zn, Na, Ca and Mg simulating the composition of produced waters in the state of Rio Grande do Norte, Brazil. The breakthrough curves for simultaneous removal of copper ions and zinc as a result, 84.3% for calcined diatomite and diatomite with 97.3 % for fluxing. The calcined fluxing diatomite was more efficient permeability through the bed and removal of copper and zinc ions. The fresh diatomite had trouble with the permeability through the bed under the conditions tested, compared with the other obtained diatomite. The results are presented as promising for application in the petroleum industry

Remoção de metais pesados em efluentes sintéticos utilizando vermiculita como adsorvente

Heavy metals are used in many industrial processestheirs discard can harm fel effects to the environment, becoming a serious problem. Many methods used for wastewater treatment have been reported in the literature, but many of them have high cost and low efficiency. The adsorption process has been used as effective for the metal remoal ions. This paper presents studies to evaluate the adsorption capacity of vermiculite as adsorbent for the heavy metals removal in a synthetic solution. The mineral vermiculite was characterized by differents techniques: specific surface area analysis by BET method, X-ray diffraction, raiosX fluorescence, spectroscopy in the infraredd region of, laser particle size analysis and specific gravity. The physical characteristics of the material presented was appropriate for the study of adsorption. The adsorption experiments weredriveal finite bath metod in synthetic solutions of copper, nickel, cadmium, lead and zinc. The results showed that the vermiculite has a high potential for adsorption, removing about 100% of ions and with removal capacity values about 85 ppm of metal in solution, 8.09 mg / g for cadmium, 8.39 mg/g for copper, 8.40 mg/g for lead, 8.26 mg/g for zinc and 8.38 mg/g of nickel. The experimental data fit in the Langmuir and Freundlich models. The kinetic datas showed a good correlation with the pseudo-second order model. It was conducteas a competition study among the metals using vermiculiti a adsorbent. Results showed that the presence of various metals in solution does not influence their removal at low concentrations, removing approximat wasely 100 % of all metals present in solutions

Estudo de adsorvente obtido de terras diatomáceas para remoção de metais pesados em águas produzidas: processamento, caracterização e dinâmica em leito fixo

The acceleration of industrial growth in recent decades on all continents aroused the interest of the companies to counter the impacts produced on the environment, spurred primarily by major disasters in the petroleum industry. In this context, the water produced is responsible for the largest volume of effluent from the production and extraction of oil and natural gas. This effluent has in its composition some critical components such as inorganic salts, heavy metals (Fe, Cu, Zn, Pb, Cd, ), presence of oil and chemicals added in the various production processes. In response to impact, have been triggered by research alternative adsorbent materials for water treatment and water produced, in order to removing oils and acids and heavy metals. Many surveys of diatomaceous earth (diatomite) in Brazil involve studies on the physico-chemical, mineral deposits, extraction, processing and applications. The official estimated Jazi are around 2.5 million tonnes, the main located in the states of Bahia (44%) and Rio Grande do Norte (37,4%). Moreover, these two states appear as large offshore producers, earning a prominent role in research of adsorbents such as diatomite for treatment of water produced. Its main applications are as an agent of filtration, adsorption of oils and greases, industrial load and thermal insulator. The objective of this work was the processing and characterization of diatomite diatomaceous earth obtained from the municipality of Macaíba-RN (known locally as tabatinga) as a low cost regenerative adsorbent for removal of heavy metals in the application of water produced treatment. In this work we adopted a methodology for batch processing, practiced by small businesses located in producing regions of Brazil. The characterization was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and specific surface area (BET). Research conducted showed that the improvement process used was effective for small volume production of diatomite concentrated. The diatomite obtained was treated by calcination at temperature of 900 oC for 2 hours, with and without fluxing Na2CO3 (4%), according to optimal results in the literature. Column adsorption experiments were conducted to percolation of the in nature, calcined and calcined fluxing diatomites. Effluent was used as a saline solution containing ions of Cu, Zn, Na, Ca and Mg simulating the composition of produced waters in the state of Rio Grande do Norte, Brazil. The breakthrough curves for simultaneous removal of copper ions and zinc as a result, 84.3% for calcined diatomite and diatomite with 97.3 % for fluxing. The calcined fluxing diatomite was more efficient permeability through the bed and removal of copper and zinc ions. The fresh diatomite had trouble with the permeability through the bed under the conditions tested, compared with the other obtained diatomite. The results are presented as promising for application in the petroleum industry