A straightforward method to obtain the cohesive laws of bonded joints under mode I loading

A simple procedure to measure the cohesive laws of bonded joints under mode I loading using the double cantilever beam test is proposed. The method only requires recording the applied load–displacement data and measuring the crack opening displacement at its tip in the course of the experimental test. The strain energy release rate is obtained by a procedure involving the Timoshenko beam theory, the specimen’s compliance and the crack equivalent concept. Following the proposed approach the influence of the fracture process zone is taken into account which is fundamental for an accurate estimation of the failure process details. The cohesive law is obtained by differentiation of the strain energy release rate as a function of the crack opening displacement. The model was validated numerically considering three representative cohesive laws. Numerical simulations using finite element analysis including cohesive zone modeling were performed. The good agreement between the inputted and resulting laws for all the cases considered validates the model. An experimental confirmation was also performed by comparing the numerical and experimental load–displacement curves. The numerical load–displacement curves were obtained by adjusting typical cohesive laws to the ones measured experimentally following the proposed approach and using finite element analysis including cohesive zone modeling. Once again, good agreement was obtained in the comparisons thus demonstrating the good performance of the proposed methodology.

Modelling adhesive joints with cohesive zone models: effect of the cohesive law shape of the adhesive layer

Adhesively-bonded joints are extensively used in several fields of engineering. Cohesive Zone Models (CZM) have been used for the strength prediction of adhesive joints, as an add-in to Finite Element (FE) analyses that allows simulation of damage growth, by consideration of energetic principles. A useful feature of CZM is that different shapes can be developed for the cohesive laws, depending on the nature of the material or interface to be simulated, allowing an accurate strength prediction. This work studies the influence of the CZM shape (triangular, exponential or trapezoidal) used to model a thin adhesive layer in single-lap adhesive joints, for an estimation of its influence on the strength prediction under different material conditions. By performing this study, guidelines are provided on the possibility to use a CZM shape that may not be the most suited for a particular adhesive, but that may be more straightforward to use/implement and have less convergence problems (e.g. triangular shaped CZM), thus attaining the solution faster. The overall results showed that joints bonded with ductile adhesives are highly influenced by the CZM shape, and that the trapezoidal shape fits best the experimental data. Moreover, the smaller is the overlap length (LO), the greater is the influence of the CZM shape. On the other hand, the influence of the CZM shape can be neglected when using brittle adhesives, without compromising too much the accuracy of the strength predictions.

Numerical evaluation of three-dimensional scarf repairs in carbon-epoxy structures

The widespread employment of carbon-epoxy laminates in high responsibility and severely loaded applications introduces an issue regarding their handling after damage. Repair of these structures should be evaluated, instead of their disposal, for cost saving and ecological purposes. Under this perspective, the availability of efficient repair methods is essential to restore the strength of the structure. The development and validation of accurate predictive tools for the repairs behaviour are also extremely important, allowing the reduction of costs and time associated to extensive test programmes. Comparing with strap repairs, scarf repairs have the advantages of a higher efficiency and the absence of aerodynamic disturbance. This work reports on a numerical study of the tensile behaviour of three-dimensional scarf repairs in carbon-epoxy structures, using a ductile adhesive (Araldite® 2015). The finite elements analysis was performed in ABAQUS® and Cohesive Zone Modelling was used for the simulation of damage onset and growth in the adhesive layer. Trapezoidal cohesive laws in each pure mode were used to account for the ductility of the specific adhesive mentioned. A parametric study was performed on the repair width and scarf angle. The use of over-laminating plies covering the repaired region at the outer or both repair surfaces was also tested as an attempt to increase the repairs efficiency. The obtained results allowed the proposal of design principles for repairing composite structures.

Single-lap joints of similar and dissimilar adherends bonded with an acrylic adhesive

In this study, the tensile strength of single-lap joints (SLJs) between similar and dissimilar adherends bonded with an acrylic adhesive was evaluated experimentally and numerically. The adherend materials included polyethylene (PE), polypropylene (PP), carbon-epoxy (CFRP), and glass-polyester (GFRP) composites. The following adherend combinations were tested: PE/PE, PE/PP, PE/CFRP, PE/GFRP, PP/PP, CFRP/CFRP, and GFRP/GFRP. One of the objectives of this work was to assess the influence of the adherends stiffness on the strength of the joints since it significantly affects the peel stresses magnitude in the adhesive layer. The experimental results were also used to validate a new mixed-mode cohesive damage model developed to simulate the adhesive layer. Thus, the experimental results were compared with numerical simulations performed in ABAQUS®, including a developed mixed-mode (I+II) cohesive damage model, based on the indirect use of fracture mechanics and implemented within interface finite elements. The cohesive laws present a trapezoidal shape with an increasing stress plateau, to reproduce the behaviour of the ductile adhesive used. A good agreement was found between the experimental and numerical results.

Estudo da resistência e mecanismos de dano em juntas adesivas entre materiais compósitos com defeitos de adesão

A necessidade de utilizar métodos de ligação entre componentes de forma mais rápida, eficaz e com melhores resultados tem causado a crescente utilização das juntas adesivas, em detrimento dos métodos tradicionais de ligação. A utilização das juntas adesivas tem vindo a aumentar em diversas aplicações industriais por estas apresentarem vantagens, das quais se destacam a redução de peso, redução de concentrações de tensões e facilidade de fabrico. No entanto, uma das limitações das juntas adesivas é a dificuldade em prever a resistência da junta após fabrico e durante a sua vida útil devido à presença de defeitos no adesivo. Os defeitos são normalmente gerados pela preparação inadequada das juntas ou degradação do adesivo devido ao ambiente (por exemplo, humidade), reduzindo a qualidade da ligação e influenciando a resistência da junta. Neste trabalho é apresentado um estudo experimental e numérico de juntas de sobreposição simples (JSS) com a inclusão de defeitos centrados na camada de adesivo para comprimentos de sobreposição (LO) diferentes. Os adesivos utilizados foram o Araldite® AV138, apresentado como sendo frágil, e o adesivo Sikaforce® 7752, intitulado como adesivo dúctil. A parte experimental consistiu no ensaio à tração das diferentes JSS permitindo a obtenção das curvas força-deslocamento (P-δ). A análise numérica por modelos de dano coesivo (MDC) foi realizada para analisar as tensões de arrancamento ((σy) e as tensões de corte (τxy) na camada adesiva, para estudar a variável de dano do MDC durante o processo de rotura e para avaliar a capacidade dos MDC na previsão da resistência da junta. Constatou-se um efeito significativo dos defeitos de diferentes dimensões na resistência das juntas, que também depende do tipo de adesivo utilizado e do valor de LO. Os modelos numéricos permitiram a descrição detalhada do comportamento das juntas e previsão de resistência, embora para o adesivo dúctil a utilização de uma lei coesiva triangular tenha provocado alguma discrepância relativamente aos resultados experimentais.

Estudo numérico da adequação de diferentes tipos de leis coesivas na previsão da resistência de juntas adesivas por Modelos de Dano Coesivo

O uso de ligações adesivas aumentou significativamente nos últimos anos e é hoje em dia uma técnica de ligação dominante na indústria aeronáutica e automóvel. As ligações adesivas visam substituir os métodos tradicionais de fixação mecânicos na união de estruturas. A melhoria ao longo dos anos de vários modelos de previsão de dano, nomeadamente através do Método de Elementos Finitos (MEF), tem ajudado ao desenvolvimento desta técnica de ligação. Os Modelos de Dano coesivo (MDC), usados em conjunto com MEF, são uma ferramenta viável para a previsão de resistência de juntas adesivas. Os MDC combinam critérios da resistência dos materiais para a iniciação do dano e conceitos da mecânica da fratura para a propagação da fenda. Existem diversas formas de leis coesivas possíveis de aplicar em simulações por MDC, em função do comportamento expectável dos materiais que estão a ser simulados. Neste trabalho, estudou-se numericamente o efeito de diversas formas de leis coesivas na previsão no comportamento de juntas adesivas, nomeadamente nas curvas forçadeslocamento (P-) de ensaios Double-Cantilever Beam para caracterização à tração e ensaios End-Notched Flexure para caraterização ao corte. Também se estudou a influência dos parâmetros coesivos à tração e corte nas curvas P- dos referidos ensaios. Para o Araldite®AV138 à tração e ao corte, a lei triangular é a que melhor prevê o comportamento do adesivo. Para a previsão da resistência de ambos os adesivos Araldite® 2015 e SikaForce® 7752, a lei trapezoidal é a que melhor se adequa, confirmando assim que esta lei é a que melhor caracteriza o comportamento de dano de adesivos tipicamente dúcteis. O estudo dos parâmetros revelou influência distinta na previsão do comportamento das juntas, embora com bastantes semelhanças entre os diferentes tipos de adesivos.

Modelação de juntas adesivas por modelos de dano coesivo utilizando o método direto

A utilização de adesivos hoje em dia encontra-se de tal forma disseminada que é transversal a diversos setores do mercado, como a indústria aeroespacial, aeronáutica, automóvel e do desporto. De facto, o uso de ligações adesivas em estruturas mecânicas tem vindo a crescer, na medida em que estes têm substituído os métodos de ligação convencionais, tais como brasagem, rebitagem, ligações aparafusadas e soldadura. No geral, as ligações adesivas apresentam diversas vantagens, desde a diminuição do peso, redução da concentração de tensões, facilidade de fabrico, bom comportamento a solicitações cíclicas e capacidade de unir materiais dissimilares. O crescente interesse da indústria nas ligações adesivas tem por base o aumento da confiabilidade nos métodos de previsão de resistência de estruturas adesivas. Neste contexto surgem os Modelos de Dano Coesivo, que permitem simular o crescimento do dano em estruturas, após introdução das leis coesivas previamente estimadas nos modelos numéricos. Uma das fases mais importantes neste método de previsão é a estimativa das leis coesivas em tração e corte, pelo que se torna de grande relevância a existência e validação de métodos precisos para a obtenção destas leis. Este trabalho visa a validação de leis coesivas em tração e corte, estimadas pela aplicação do método direto, na previsão da resistência de juntas com geometria de solicitação mista. Neste âmbito, ensaiaram-se JSS e JSD com diferentes comprimentos de sobreposição e com adesivos de diferente ductilidade. Foram considerados os adesivos Araldite® AV138, de elevada resistência e baixa ductilidade, o Araldite® 2015, de moderada ductilidade e resistência intermédia, e o SikaForce® 7752, de baixa resistência e elevada ductilidade. As leis coesivas em modo puro serviram de base para a criação de leis simplificadas triangulares, trapezoidais e linearesexponenciais, que foram testadas para cada um dos adesivos. A validação das mesmas consumou-se por comparação das previsões numéricas com os resultados experimentais. Procedeu-se também a uma análise de tensões de arrancamento e de corte no adesivo, de modo a compreender a influência das tensões na resistência das juntas. A utilização do método direto permitiu obter previsões de resistência bastante precisas, indicando as formas de leis coesivas mais adequadas para cada conjunto adesivo/geometria de junta. Para além disso, para as condições geométricas e materiais consideradas, este estudo permitiu concluir que não se cometem erros significativos na escolha de uma lei menos adequada.

Validação numérica de leis coesivas triangulares para previsão de resistência de juntas adesivas em tração e corte puros

As ligações adesivas surgiram pela necessidade de se encontrar formas de unir componentes, por vezes de materiais distintos, através de técnicas mais vantajosas. Atualmente, qualquer estrutura deve ser resistente, robusta e leve, o que amplificou o interesse industrial e investigação nas ligações adesivas, principalmente na melhoria das propriedades de resistência e fratura de materiais. Desta forma, nos últimos anos, a utilização de juntas adesivas em aplicações industriais tem aumentando gradualmente, substituindo alguns métodos de ligação tradicionais, por apresentarem vantagens, tais como redução de concentração de tensões, reduzido peso e facilidade de processamento/fabrico. Em qualquer área da indústria, a aplicação em larga escala de uma determinada técnica de ligação supõe que estão disponíveis ferramentas confiáveis para o projeto e previsão da rotura. Neste âmbito, os Modelos de Dano Coesivo (MDC) são uma ferramenta fundamental, apesar de ser necessário estimar as leis coesivas do adesivo à tração e corte para entrada nos modelos numéricos. Nesta dissertação o trabalho experimental consistiu no tratamento de dados com vista à obtenção de GIc e GIIc, com a devida comparação de diferentes métodos de redução, bem como potencialidades e limitações dos mesmos. É realizada uma comparação dos três adesivos: Araldite® AV138, Araldite® 2015 e SikaForce® 7752. Neste trabalho estudou-se também numericamente a adequação de leis coesivas triangulares na previsão no comportamento de juntas adesivas, nomeadamente nas curvas forçadeslocamento (P-) de ensaios Double-Cantilever Beam para caracterização à tração e ensaios End-Notched Flexure para caraterização ao corte. Os ensaios foram simulados numericamente pelo software ABAQUS®, recorrendo ao Método de Elementos Finitos (MEF) e um MDC triangular, com o intuito de estimar a lei coesiva de cada um dos adesivos. Para os adesivos Araldite®AV138 e Araldite®2015, à tração e ao corte, a lei triangular previu o comportamento do adesivo com alguma razoabilidade. Para a previsão da resistência do adesivo SikaForce® 7752, a lei triangular não se ajustou convenientemente nem à tração nem ao corte. Considera-se que, para este adesivo, uma lei trapezoidal é a que melhor se adequa, devido à ductilidade do mesmo.

Monte Carlo simulation of complex cohesive fracture in random heterogeneous quasi-brittle materials

A numerical method is developed to simulate complex two-dimensional crack propagation in quasi-brittle materials considering random heterogeneous fracture properties. Potential cracks are represented by pre-inserted cohesive elements with tension and shear softening constitutive laws modelled by spatially varying Weibull random fields. Monte Carlo simulations of a concrete specimen under uni-axial tension were carried out with extensive investigation of the effects of important numerical algorithms and material properties on numerical efficiency and stability, crack propagation processes and load-carrying capacities. It was found that the homogeneous model led to incorrect crack patterns and load–displacement curves with strong mesh-dependence, whereas the heterogeneous model predicted realistic, complicated fracture processes and load-carrying capacity of little mesh-dependence. Increasing the variance of the tensile strength random fields with increased heterogeneity led to reduction in the mean peak load and increase in the standard deviation. The developed method provides a simple but effective tool for assessment of structural reliability and calculation of characteristic material strength for structural design.

Privacy invasive geo-mashups : privacy 2.0 and the limits of first generation information privacy laws

Online technological advances are pioneering the wider distribution of geospatial information for general mapping purposes. The use of popular web-based applications, such as Google Maps, is ensuring that mapping based applications are becoming commonplace amongst Internet users which has facilitated the rapid growth of geo-mashups. These user generated creations enable Internet users to aggregate and publish information over specific geographical points. This article identifies privacy invasive geo-mashups that involve the unauthorized use of personal information, the inadvertent disclosure of personal information and invasion of privacy issues. Building on Zittrain’s Privacy 2.0, the author contends that first generation information privacy laws, founded on the notions of fair information practices or information privacy principles, may have a limited impact regarding the resolution of privacy problems arising from privacy invasive geo-mashups. Principally because geo-mashups have different patterns of personal information provision, collection, storage and use that reflect fundamental changes in the Web 2.0 environment. The author concludes by recommending embedded technical and social solutions to minimize the risks arising from privacy invasive geo-mashups that could lead to the establishment of guidelines for the general protection of privacy in geo-mashups.

Regulating Multi-National Corporations Through State-Based Laws : Problems with Enforcing Human Rights Under The Alien Tort Statute

Under the Alien Tort Statute United States of America (“America”) Federal Courts have the jurisdiction to hear claims for civil wrongs, committed against non-American citizens, which were perpetrated outside America’s national borders. The operation of this law has confronted American Federal Courts with difficulties on how to manage conflicts between American executive foreign policy and judicial interpretations of international law. Courts began to pass judgment over conduct which was approved by foreign governments. Then in 2005 the American Supreme Court wound back the scope of the Alien Tort Statute. This article will review the problems with the expansion of the Alien Tort Statute and the reasons for its subsequent narrowing.

Driving and licensing experiences of learner drivers in two Australian states prior to major changes in the licensing laws

The learner licence is an important component of the graduated driver licensing system. This research describes the driving and licensing experiences of learner drivers in Queensland and New South Wales licensed prior to the changes made to the system in mid-2007. The sample consisted of 392 participants who completed a telephone interview just after they obtained their provisional licence. The results suggest that learner drivers in the two states had many similar experiences when they were obtaining a learner licence. However, once a learner licence was obtained, there were differences in the amount of practice, the supervisor learners practised with, the type of vehicle they used and the amount of unlicensed driving. This paper provides important baseline descriptive data that can be used to measure the impact of the changes that were introduced to the learner licence phase in mid-2007 in both of these states.

National consumer credit laws, financial exclusion and interest rate caps : The case for diversity within a centralised framework

Australia is going through a major reform of consumer credit regulation, with the implementation of a proposal to transfer regulatory responsibility from the State and Territory Governments to the Commonwealth Government. While the broad policy approach is supported, the reform process has missed a significant opportunity to engage directly with issues of financial exclusion and with the potential role of regulation to reduce financial exclusion. The imposition of an interest rate cap can limit the impact of financial exclusion. However, the future of the existing interest rate caps is uncertain, given the diversity of approaches, and the heated debate that surrounds this issue. In the absence of support for regulatory initiatives to increase the availability of low cost, small loans, permitting regulatory diversity on this issue of interest rate caps, within an otherwise centralised regulatory framework., can minimise the impact of financial exclusion on consumers.

"There's no way in hell I would pull up" : Deterrent and other effects of vehicle impoundment laws for hooning

Traffic law enforcement is based on deterrence principles, whereby drivers control their behaviour in order to avoid an undesirable sanction. For “hooning”-related driving behaviours in Queensland, the driver’s vehicle can be impounded for 48 hours, 3 months, or permanently depending on the number of previous hooning offences. It is assumed that the threat of losing something of value, their vehicle, will discourage drivers from hooning. While official data shows that the rate of repeat offending is low, an in-depth understanding of the deterrent effects of these laws should involve qualitative research with targeted drivers. A sample of 22 drivers who reported engaging in hooning behaviours participated in focus group discussions about the vehicle impoundment laws as applied to hooning offences in Queensland. The findings suggested that deterrence theory alone cannot fully explain hooning behaviour, as participants reported hooning frequently, and intended to continue doing so, despite reporting that it is likely that they will be caught, and perceiving the vehicle impoundment laws to be extremely severe. The punishment avoidance aspect of deterrence theory appears important, as well as factors over and above legal issues, particularly social influences. A concerning finding was drivers’ willingness to flee from police in order to avoid losing their vehicle permanently for a third offence, despite acknowledging risks to their own safety and that of others. This paper discusses the study findings in terms of the implications for future research directions, enforcement practices and policy development for hooning and other traffic offences for which vehicle impoundment is applied.

Developments in Australian laws requiring the reporting of suspected child sexual abuse

Thousands of Australian children are sexually abused every year, and the effects can be severe and long lasting. Not only is child sexual abuse a public health problem, but the acts inflicted are criminal offences. Child sexual abuse usually occurs in private, typically involving relationships featuring a massive imbalance in power and an abuse of that power. Those who inflict child sexual abuse seek to keep it secret, whether by threats or more subtle persuasion. As a method of responding to this phenomenon and in an effort to uncover cases of sexual abuse that otherwise would not come to light, governments in Australian States and Territories have enacted legislation requiring designated persons to report suspected child sexual abuse. With Western Australia’s new legislation having commenced on 1 January 2009, every Australian State and Territory government has now passed these laws, so that there is now, for the first time, an almost harmonious legislative approach across Australia to the reporting of child sexual abuse. Yet there remain differences in the State and Territory laws regarding who has to make reports, which cases of sexual abuse are required to be reported, and whether suspected future abuse must be reported. These differences indicate that further refinement of the laws is required