A study on chemical constituents and sugars extraction from spent coffee grounds

Spent coffee grounds (SCG) the residual materials obtained during the processing of raw coffee powder to prepare instant coffee are the main coffee Industry residues In the present work this material was chemically characterized and subsequently submitted to a dilute acid hydrolysis aiming to recover the hemicellulose sugars Reactions were performed according to experimental designs to verify the effects of the variables H(2)SO(4) concentration liquid-to-solid ratio temperature and reaction time on the efficiency of hydrolysis SCG was found to be rich in sugars (45 3% w/w) among of which hemicellulose (constituted by mannose galactose and arabinose) and cellulose (glucose homopolymer) correspond to 367% (w/w) and 8 6% (w/w) respectively Optimal conditions for hemicellulose sugars extraction consisted in using 100 mg acid/g dry matter 10g liquid/g solid at 163 degrees C for 45 min Under these conditions hydrolysis efficiencies of 100% 774% and 895% may be achieved for galactan mannan and arabinan respectively corresponding to a hemicellulose hydrolysis efficiency of 874% (C) 2010 Elsevier Ltd All rights reserved

Spent coffee grounds for biodiesel production and other applications

This work evaluates the possibility of using spent coffee grounds (SCG) for biodiesel production and other applications. An experimental study was conducted with different solvents showing that lipid content up to 6 wt% can be obtained from SCG. Results also show that besides biodiesel production, SCG can be used as fertilizer as it is rich in nitrogen, and as solid fuel with higher heating value (HHV) equivalent to some agriculture and wood residues. The extracted lipids were characterized for their properties of acid value, density at 15 °C, viscosity at 40 °C, iodine number, and HHV, which are negatively influenced by water content and solvents used in lipid extraction. Results suggest that for lipids with high free fatty acids (FFA), the best procedure for conversion to biodiesel would be a two-step process of acid esterification followed by alkaline transesterification, instead of a sole step of direct transesterification with acid catalyst. Biodiesel was characterized for its properties of iodine number, acid value, and ester content. Although these quality parameters were not within the limits of NP EN 14214:2009 standard, SCG lipids can be used for biodiesel, blended with higher-quality vegetable oils before transesterification, or the biodiesel produced from SCG can be blended with higher-quality biodiesel or even with fossil diesel, in order to meet the standard requirements.

Effects of caffeine and used coffee grounds on biological features of Aedes aegypti (Diptera, Culicidae) and their possible use in alternative control

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Espresso coffee residues: a valuable source of unextracted compounds

Espresso spent coffee grounds were chemically characterized to predict their potential, as a source of bioactive compounds, by comparison with the ones from the soluble coffee industry. Sampling included a total of 50 samples from 14 trademarks, collected in several coffee shops and prepared with distinct coffee machines. A high compositional variability was verified, particularly with regard to such water-soluble components as caffeine, total chlorogenic acids (CGA), and minerals, supported by strong positive correlations with total soluble solids retained. This is a direct consequence of the reduced extraction efficiency during espresso coffee preparation, leaving a significant pool of bioactivity retained in the extracted grounds. Besides the lipid (12.5%) and nitrogen (2.3%) contents, similar to those of industrial coffee residues, the CGA content (478.9 mg/100 g), for its antioxidant capacity, and its caffeine content (452.6 mg/100 g), due to its extensive use in the food and pharmaceutical industries, justify the selective assembly of this residue for subsequent use.

Improvement of vegetables elemental quality by espresso coffee residues

Spent coffee grounds (SCG) are usually disposed as common garbage, without specific reuse strategies implemented so far. Due to its recognised richness in bioactive compounds, the effect of SCG on lettuce’s macro- and micro-elements was assessed to define its effectiveness for agro industrial reuse. A greenhouse pot experiment was conducted with different amounts of fresh and composted spent coffee, and potassium, magnesium, phosphorous, calcium, sodium, iron, manganese, zinc and copper were analysed. A progressive decrease on all lettuce mineral elements was verified with the increase of fresh spent coffee, except for potassium. In opposition, an increment of lettuce’s essential macro-elements was verified when low amounts of composted spent coffee were applied (5%, v/v), increasing potassium content by 40%, manganese by 30%, magnesium by 20%, and sodium by 10%, of nutritional relevance This practical approach offers an alternative reuse for this by-product, extendable to other crops, providing value-added vegetable products.

Revalorization of spent coffee residues by a direct agronomic approach

Spent coffee grounds (SCG) represent a high-volume food waste worldwide, and several reuse approaches have been attempted. Herein, a greenhouse field experiment was carried out by cultivating Batavia lettuce with 5%, 10%, 15%, 20% and 30% (v/v) espresso SCG directly composted in the soil. Healthy vegetables were obtained for all treatments, without yield loss for up to 10% SCG. A progressive increment of green color intensity with increasing SCG content was observed, corroborated by the increase of their photosynthetic pigments (chlorophylls and carotenoids). Furthermore, total ascorbic acid and tocopherols showed statistical significant increases (p < 0.001) between control and all tested groups. Marked variations of nutritionally relevant minerals, particularly potassium, phosphorous and sodium were also revealed at higher percentage treatments (20% and 30%). This approach constitutes a clean, direct, simple and cost-effective measure to produce value-added vegetables, while reducing food waste disposal.

From coffee industry waste materials to skin-friendly products with improved skin fat levels

Spent coffee grounds (SCG), which are the residue obtained from the treatment of coffee with hot water or steam, can be used for industrial applications, due to the high content in lipids. The cosmetic products might be a suitable application for these types of residues because the barrier properties of the stratum corneum (SC) are largely dependent on the intactness of the lipid lamellae that surrounds the corneocytes. The purpose of this work was to assess the feasibility of using the lipid fraction of SCG extracted with supercritical carbon dioxide in the development of new cosmetic formulations with improved skin lipids (sebum) and hydration. The use of spent coffee lipid extract in cosmetic industry seems to be a suitable approach to recycle the wastes from coffee industry. Emulsion containing 10% of the lipid fraction of SCG (SpentCofOil cream) presented promising characteristics in the improvement of sebum skin levels with a good acceptance by consumers when compared to an emulsion containing 10% w/w of green coffee oil (GreenCofOil cream) and a placebo without coffee oil (NoCofOil cream). Practical applications: In this work, the authors develop and characterize a cream containing 10% of the lipid fraction of SCG extracted with supercritical carbon dioxide with improved skin lipids (sebum) and hydration. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Sugars metabolism and ethanol production by different yeast strains from coffee industry wastes hydrolysates

Significant amounts of wastes are generated by the coffee industry, among of which, coffee silverskin (CS) and spent coffee grounds (SCG) are the most abundantly generated during the beans roasting and instant coffee preparation, respectively. This study evaluated the sugars metabolism and production of ethanol by three different yeast strains (Saccharomyces cerevisiae, Pichia stipitis and Kluyveromyces fragilis) when cultivated in sugar rich hydrolysates produced by acid hydrolysis of CS and SCG. S. cerevisiae provided the best ethanol production from SCG hydrolysate (11.7 g/l, 50.2% efficiency). On the other hand, insignificant (<= 1.0 g/l) ethanol production was obtained from CS hydrolysate, for all the evaluated yeast strains, probably due to the low sugars concentration present in this medium (approx. 22 g/l). It was concluded that it is possible to reuse SCG as raw material for ethanol production, which is of great interest for the production of this biofuel, as well as to add value to this agro-industrial waste. CS hydrolysate, in the way that is produced, was not a suitable fermentation medium for ethanol production; however, the hydrolysate concentration for the sugars content increase previous the use as fermentation medium could be an alternative to overcome this problem. (C) 2011 Elsevier Ltd. All rights reserved.

Synthesis of biodiesel from wastes of food industry via direct transesterification with methanol/carbon dioxide mixtures

Dissertation presented at Faculdade de Ciências e Tecnologia from Universidade Nova de Lisboa to obtain the degree of Master in Chemical and Biochemical Engineering

Continuous catalyst free production of biodiesel from agro industrial waste with green solvents

Dissertação para obtenção do Grau de Mestre em Engenharia Química e Bioquímica

Valorização da Borra de Café: Otimização da Produção de Biodiesel por Catálise Enzimática

O decréscimo das reservas de petróleo e as consequências ambientais resultantes do recurso a combustíveis fósseis nos motores a diesel têm levado à procura de combustíveis alternativos. Esta pesquisa alicerçada nas fontes de energia renovável tornou-se essencial, face à crescente procura de energia e ao limitado fornecimento de combustíveis fósseis . Resíduos de óleo de cozinha, gordura animal, entre outros resíduos de origem biológica, tais como a borra de café, são exemplos de matérias-primas para a produção de biodiesel. A sua valorização tem interesse quer pela perspetiva ambiental, quer pela económica, pois aumenta não só a flexibilidade e diversificação das matérias-primas, mas também contribui para uma estabilidade de custos e alteração nas políticas agrícolas e de uso do solo. É neste contexto que se enquadra o biodiesel e a borra de café, pretendendo-se aqui efetuar o estudo da produção, à escala laboratorial, de biodiesel a partir da borra de café, por transesterificação enzimática, visando a procura das melhores condições reacionais. Iniciando-se com a caracterização da borra de café, foram avaliados antes e após a extração do óleo da borra de café, diversos parâmetros, de entre os quais se destacam: o teor de humidade (16,97% e 6,79%), teor de cinzas (1,91 e 1,57%), teor de azoto (1,71 e 2,30%), teor de proteínas (10,7 e 14,4%), teor de carbono (70,2 e 71,7%), teor de celulose bruta (14,77 e 18,48%), teor de lenhina (31,03% e 30,97%) e poder calorifico superior (19,5 MJ/kg e 19,9 MJ/kg). Sumariamente, constatou-se que os valores da maioria dos parâmetros não difere substancialmente dos valores encontrados na literatura, tendo sido evidenciado o potencial da utilização desta biomassa, como fonte calorifica para queima e geração de energia. Sendo a caracterização do óleo extraído da borra de café um dos objetivos antecedentes à produção do biodiesel, pretendeu-se avaliar os diferentes parâmetros mais significativos. No que diz respeito à caracterização do óleo extraído, distingue-se a sua viscosidade cinemática (38,04 mm2/s), densidade 0,9032 g/cm3, poder calorífico de 37,9 kcal/kg, índice de iodo igual a 63,0 gI2/ 100 g óleo, o teor de água do óleo foi de 0,15 %, o índice de acidez igual a 44,8 mg KOH/g óleo, ponto de inflamação superior a 120 ºC e teor em ácidos gordos de 82,8%. Inicialmente foram efetuados ensaios preliminares, a fim de selecionar a lipase (Lipase RMIM, TL 100L e CALB L) e álcool (metanol ou etanol puros) mais adequados à produção de biodiesel, pelo que o rendimento de 83,5% foi obtido através da transesterificação mediada pela lipase RMIM, utilizando como álcool o etanol. Sendo outro dos objetivos a otimização do processo de transesterificação enzimática, através de um desenho composto central a três variáveis (razão molar etanol: óleo, concentração de enzima e temperatura), recorrendo ao software JMP 8.0, determinou-se como melhores condições, uma razão molar etanol: óleo 5:1, adição de 4,5% (m/m) de enzima e uma temperatura de 45 ºC, que conduziram a um rendimento experimental equivalente a 96,7 % e teor de ésteres 87,6%. Nestas condições, o rendimento teórico foi de 99,98%. Procurou-se ainda estudar o efeito da adição de água ao etanol, isto é, o efeito da variação da concentração do etanol pela adição de água, para teores de etanol de 92%, 85% e 75%. Verificou-se que até 92% decorreu um aumento da transesterificação (97,2%) para um teor de ésteres de (92,2%), pelo que para teores superiores de água adicionada (75% e 85%) ocorreu um decréscimo no teor final em ésteres (77,2% e 89,9%) e no rendimento da reação (84,3% e 91,9%). Isto indica a ocorrência da reação de hidrólise em maior extensão, que leva ao desvio do equilíbrio no sentido contrário à reação de formação dos produtos, isto é, dos ésteres. Finalmente, relativamente aos custos associados ao processo de produção de biodiesel, foram estimados para o conjunto de 27 ensaios realizados neste trabalho, e que corresponderam a 767,4 g de biodiesel produzido, sendo o custo dos reagentes superior ao custo energético, de 156,16 € e 126,02 €, respetivamente. Naturalmente que não esperamos que, a nível industrial os custos sejam desta ordem de grandeza, tanto mais que há economia de escala e que as enzimas utilizadas no processo deveriam ser reutilizadas diversas vezes.

Production of chitin-glucan complex by Pichia pastoris

Dissertation for the Degree of Master in Biotechnology

Accidents caused by Bothrops and Bothropoides in the State of Paraiba: epidemiological and clinical aspects

INTRODUCTION: Bothrops and Bothropoides snakes cause 70% of the ophidic accidents in Brazil. The species that cause ophidic accidents in State of Paraíba are Bothropoides erythromelas, Bothrops leucurus and Bothropoides neuwiedi. METHODS: This is a prospective and transverse study, following a quantitative approach of accidents involving Bothrops and Bothropoides admitted to the Toxicological Assistance and Information Centers of Campina Grande and João Pessoa (Ceatox-CG and Ceatox-JP), aimed at identifying the epidemiological and clinical profile of such accidents. All of the patients admitted had medical diagnoses and were monitored at Ceatox-CG or Ceatox-JP. RESULTS: The genera Bothrops and Bothropoides caused 91.7% of the ophidic accidents reported. Snake bites were frequent in men (75.1%), rural workers (65.1%), literate individuals (69%) between 11 and 20 years-old (21.7%), and toes the most common area attacked (52.7%). Most (86.6%) patients were admitted within 6 hours after the accident/bite, with a predominance of mild cases (64.6%). The annual occurrence in Paraíba was 5.5 accidents/100,000 inhabitants and lethality was 0.2%. CONCLUSIONS: Positive changes in the profiles of these accidents were verified, such as the non-application of inadequate solutions, including the use of tourniquet, coffee grounds, garlic, suction and/or cutting the bitten area. Moreover, the Itinerant Laboratory project, linked to Paraíba State University in partnership with Ceatox-CG, has contributed positively, providing several cities of the state with information regarding the prevention of accidents involving venomous animals. The local press has also contributed, reporting the educational work developed by the centers.

Valorization of agroindustrial waste

The main objective of this work is the valorization of residues from agro-industry giving them an added value. The valorization was performed by using a "green" and sustainable solvent - supercritical fluid, in this case carbon dioxide. Two residues and one biomass were used to produce two different final products, thereby emphasizing the versatility of the waste recovery - spent coffee grounds and microalgae Chlorella protothecoides to produce biodiesel, and tomato pomace to extract carotenoids. In the first part of this work it was demonstrated the possibility to obtain a conversion of coffee spent grounds oil into biodiesel, through an enzymatic transesterification reaction, of 98.01% with the following operating conditions: molar ratio oil:methanol 1:24, residence time 0.8 min, pressure 25 MPa, temperature 313,15K. In this first phase, it was also used the microalgae Chlorella protothecoides, a biomass, to produce biodiesel and favorable results were obtained with this green process compared with a traditional process - basic catalysis / acid. In the second part of this work, by an extraction with supercritical CO2 it was obtained 3.38% oil from tomato pomace under the following conditions: pressure 35.1 MPa, temperature 313,15K. It was found that this oil contains various carotenoids: β-carotene, lutein and lycopene. The latter is present in larger amount.

Production of polyhydroxyalkanoates from oil-containing substrates

Different oil-containing substrates, namely, used cooking oil (UCO), fatty acids-byproduct from biodiesel production (FAB) and olive oil deodorizer distillate (OODD) were tested as inexpensive carbon sources for the production of polyhydroxyalkanoates (PHA) using twelve bacterial strains, in batch experiments. The OODD and FAB were exploited for the first time as alternative substrates for PHA production. Among the tested bacterial strains, Cupriavidus necator and Pseudomonas resinovorans exhibited the most promising results, producing poly-3-hydroxybutyrate, P(3HB), form UCO and OODD and mcl-PHA mainly composed of 3-hydroxyoctanoate (3HO) and 3-hydroxydecanoate (3HD) monomers from OODD, respectively. Afterwards, these bacterial strains were cultivated in bioreactor. C. necator were cultivated in bioreactor using UCO as carbon source. Different feeding strategies were tested for the bioreactor cultivation of C. necator, namely, batch, exponential feeding and DO-stat mode. The highest overall PHA productivity (12.6±0.78 g L-1 day-1) was obtained using DO-stat mode. Apparently, the different feeding regimes had no impact on polymer thermal properties. However, differences in polymer‟s molecular mass distribution were observed. C. necator was also tested in batch and fed-batch modes using a different type of oil-containing substrate, extracted from spent coffee grounds (SCG) by super critical carbon dioxide (sc-CO2). Under fed-batch mode (DO-stat), the overall PHA productivity were 4.7 g L-1 day-1 with a storage yield of 0.77 g g-1. Results showed that SCG can be a bioresource for production of PHA with interesting properties. Furthermore, P. resinovorans was cultivated using OODD as substrate in bioreactor under fed-batch mode (pulse feeding regime). The polymer was highly amorphous, as shown by its low crystallinity of 6±0.2%, with low melting and glass transition temperatures of 36±1.2 and -16±0.8 ºC, respectively. Due to its sticky behavior at room temperature, adhesiveness and mechanical properties were also studied. Its shear bond strength for wood (67±9.4 kPa) and glass (65±7.3 kPa) suggests it may be used for the development of biobased glues. Bioreactor operation and monitoring with oil-containing substrates is very challenging, since this substrate is water immiscible. Thus, near-infrared spectroscopy (NIR) was implemented for online monitoring of the C. necator cultivation with UCO, using a transflectance probe. Partial least squares (PLS) regression was applied to relate NIR spectra with biomass, UCO and PHA concentrations in the broth. The NIR predictions were compared with values obtained by offline reference methods. Prediction errors to these parameters were 1.18 g L-1, 2.37 g L-1 and 1.58 g L-1 for biomass, UCO and PHA, respectively, which indicates the suitability of the NIR spectroscopy method for online monitoring and as a method to assist bioreactor control. UCO and OODD are low cost substrates with potential to be used in PHA batch and fed-batch production. The use of NIR in this bioprocess also opened an opportunity for optimization and control of PHA production process.