A Study of the Physical and Engineering Behaviour of Cochin Marine Clays

With the increase in population, housing and construction of various facilities have been a problem with urbanization. Having exhausted all the trouble free hand, man is nowon the lookout for techniques to improve areas which were originally considered uninhabitable. Thus this study is based on the nature and engineering behavior of soft clays covering long stretches of coastal line and methods to improve their geotechnical properties .The main aim of the present investigation is to study in detail the physical and engineering behavior of the marine clays of Cochin. While it is well known that the marine clays have been posing numerous problems to foundation engineers all along, the relevant literature reveals that no systematic and comprehensive study has been attempted to date. The: knowledge gained through the study is suitably used to improve these properties with appropriate additives.

A Study Of The Strength And Compressibility Characteristics Of Cochin Marine Clays

With the advent of urbanisation and consequent search for more and more habitable land, it was imperative that the large tracts of marine clays, considered inhabitable earlier, had to be reclaimed and developed. These marine clays, wellknown for its high compressibility and poor shear strength, posed numerous problems to the builders and Cochin was no exception. It is only less than a decade since active research work was initiated on marine clays in general and Cochin marine clays in particular. Eventhough some systematic studies are available on compressibility characteristics, attempts to study the shear strength aspects and development of techniques to improve it have been very limited. This work is an investigation on the consolidation and shear strength characteristics of Cochin marine clays including methods to improve the same

A study on the parameters affecting the compressibility characteristics of Cochin marine clays

There are numerous parameters affecting the compressibility characteristics of soft clays. A few of them such as load increment ratio, type of drainage and thickness of sample were taken up for detailed investigation. However, the main thrust in the present investigations was to develop an insight into the benefits of preloading technique, envolve procedures and establish design charts for preparation of a precompression programme which will substantially reduce the consolidation settlements of the extremely soft deposits of Cochin marine clays.

A study on mitigating the effect of sulphates in lime stabilised Cochin marine clays

Soft clays known for their high compressibility, low stiffness and low shear strength are always associated with large settlement. In place soil treatment using calcium-based stabilizers like lime and cement is a feasible solution to readdress strength deficiencies and problematic shrink/swell behaviour of unstable subgrade soils. Out of these, lime has been proved unambiguously as the most effective and economical stabilising agent for marine clays. Lime stabilisation creates long-term chemical changes in unstable clay soils to create strong, but flexible, permanent structural layers in foundations and other pavement systems. Even though calcium-based stabilizers can improve engineering properties of soft clays, problems can arise when they are used in soils rich in sulphates. It is possible for marine clays to be enriched with sulphates, either by nature or due to the discharge of nearby industrial wastes containing sulphates. The presence of sulphates is reported to adversely affect the cation exchange and pozzolanic reactions of cement and lime treated soil systems. The anions of sulphates may combine with the available calcium and alumina, and form insoluble ettringite in the soil system. Literature on sulphate attack in lime treated marine clays reports that formation of ettringite in lime-sodium sulphate-clay system is capable of adversely affecting the engineering behavior of marine clays. Only very few studies have been conducted on soft marine clays found along the coastal belt of Kerala and that too, is limited to Cochin marine clays. The studies conducted also have the limitation that the strength behaviour of lime stabilised clay was investigated only for one year. Practically no data pertaining to long term adverse effects likely to be brought about by sulphates on the strength and compressibility characteristics of Cochin marine clays is available. The overriding goal of this investigation was thus to examine the effectiveness of lime stabilisation in Cochin marine clays under varying sulphate contents. The study aims to reveal the changes brought about by varying sulphate contents on both physical and engineering properties of these clays stabilised by lime and the results for various curing periods up to two years is presented in this thesis. Quite often the load causing an unacceptable settlement may be less than the load required to cause shear failure and therefore attempt has been made in this research to highlight sulphate induced changes in both the compressibility and strength characteristics of lime treated Cochin marine clays. The study also aimed at comparing the available IS methods for sulphate quantification and has attempted to determine the threshold level of sulphate likely make these clays vulnerable by lime stabilisation. Clays used in this study were obtained from two different sites in Kochi and contained sulphate in two different concentrations viz., 0.5% and 0.1%. Two different lime percentages were tried out, 3% and 6%. Sulphate content was varied from 1% to 4% by addition of reagent grade sodium sulphate. The long term influence of naturally present sulphate is also investigated. X-ray diffraction studies and SEM studies have been undertaken to understand how the soil-lime reactions are affected in the presence of sodium sulphate. Natural sulphate content of 0.1% did not seem to have influenced normal soil lime reactions but 0.5% sulphate could induce significant changes adversely in both compressibility and strength behaviour of lime treated clays after long duration. Compressibility is seen to increase drastically with increasing sulphate content suggesting formation of ettringite on curing for longer periods. Increase in compression index and decrease in bond strength with curing period underlined the adverse effects induced in lime treated marine clays by the presence of sulphates. Presence of sulphate in concentrations ranging from 0.5 % to 4% is capable of adversely affecting the strength of lime treated marine clays. Considerable decrease is observed with increasing concentrations of sulphate. Ettringite formation due to domination of sodium ions in the system was confirmed in mineralogical studies made. Barium chloride and barium hydroxide is capable of bringing about beneficial changes both in compressibility and strength characteristics of lime treated Cochin marine clays in the presence of varying concentrations of sulphate and is strongly influenced by curing time. Clay containing sodium sulphate has increased strength values when either of barium compounds was used with lime ascompared with specimens treated with lime only. Barium hydroxide is observed to remarkably increase the strength as compared to barium chloride,when used in conjunction with lime to counteract the effect of sulphate.

Studies on the Development and Control of Desiccation cracks in compacted clay liner soils

The present study aimed at critically looking at the current practice of the installation of compacted clay liner using bentonite enhanced sand (BES). The application of bentonite is currently the most accepted practice for lining purposes. The ideal bentonite sand combination, which satisfies the liner requirements is 20% bentonite and 80% sand, was selected as one of the liner materials for the investigation of development of desiccation cracks. Locally available sundried marine clay and its combination with bentonite were also included in the study. The desiccation tests on liner materials were conducted for wet/dry cycles to simulate the seasonal variations. Digital image processing techniques were used to measure the crack intensity factor (CIF), a useful and effective parameter for quantification of desiccation cracking. The repeatability of the tests could be well established, as the variation in CIF values of identical samples had a very narrow range of 0 to 2%. The studies on the development of desiccation cracks showed that the CIF of bentonite enhanced sand mixture (BES) was 18.09%, 39.75% and 21.22% for the first, second and third cycles respectively, while it was only 9.83%, 7.52% and 4.58% respectively for sun dried marine clay (SMC). Thus the locally available, alternate liner material suggested, viz SMC, is far superior to BES, when subjected to alternate wet/dry cycles. Further, the improvement of these liner materials when amended with randomly distributed fibre reinforcements was also investigated. Three types of fibres ,namely nylon fibre, polypropylene monofilament and polypropylene fibre mesh were used for the study of fibre amended BES and SMC.The influence of these amendments on the properties of the above liner materials is also studied. The results showed that there is definite improvement in the properties of the liner materials when it is reinforced with discrete random fibres. The study also proved that the desiccation cracks could be controlled with the help of fibre reinforcement.

(Table 1) Stable carbon isotope ratios of methane and carbon dioxide from ODP Leg 169S holes

Sites 1033 and 1034 of ODP Leg 169S in Saanich Inlet have an unusual diagenetic system, that has the appearance of being depth reversed, i.e. a bacterial methane accumulation zone underlain by a sulphate reduction zone. During the late Pleistocene grey, undifferentiated, glacio-marine clays were deposited with low Corg contents (<0.4 wt.%), and interstitial fluids replete in SO4 (ca. 27 mM), devoid of CH4 and low in nutrients. This indicates oxic conditions are present, reflecting the open exchange of waters with Haro Strait during the Pleistocene before the Saanich Peninsula emerged. In the earliest Holocene (ca. 11,000 years BP) the inlet was formed, severely restricting water circulation, and leading to the presence of anoxic bottom waters. The sediments are laminated and show a dramatic rise to high Corg, Norg and Stot contents (up to 2.5, 0.4, 1.4 wt.%, respectively) over a period of ca. 1000 years. The nutrient concentrations are especially high (TA, NH4, PO4 up to 115 meq/l, 20 mM and 400 µM, respectively), SO4 is exhausted and CH4 is prolific. Stable carbon isotope ratio measurements of CH4 and co-existing CO2 indicate that methanogenesis is via carbonate reduction (delta13C-CH4 ca. -60 to - 70 per mil, delta13C-CO2 ca. +10 per mil). At the sulphate-methane interfaces, both at the near-surface and at 50 mbsf (Site 1033) and 80 mbsf (Site 1034) methane consumption by sulphate reducing bacteria is intensive.

Phosphatases from Bacteria Isolated from the Arabian Sea and Cochin Estuary

This study aims to reveal the ability of bacteria isolated from Cochin estuary and the Arabian Sea to produce phosphatases, important characters of the enzymes, its ability to utilize organophosphorus compounds as source of phosphate and also their role in degradation of organophosphorus pesticides. It deals with isolation, identification and screening of bacteria for phosphatase production, and it describes the effect of cultural conditions on growth and phosphatase production. The effect of various factors like pH, NaCl concentration, temperature of incubation, carbon source, period of incubation etc. on growth and phosphatase production by the two selected species were studied to establish suitable environment for phosphatase production by these bacteria. In this study regulation of phosphatase synthesis, characteristics of acid and alkaline phosphatases are discussed.

Ecological and Biochemical Studies On Cyanobacteria of Cochin Estuary and Their Application as Source of Antioxidants

The main objectives of the present investigation were to evaluate the qualitative and quantitative distribution of natural cyanobacterial population and their ecobiological properties along the Cochin estuary and their application in aquaculture systems as a nutritional supplement due to their nutrient-rich biochemical composition and antioxidant potential. This thesis presents a detailed account of the distribution of cyanobacteria in Cochin estuary, an assessment of physico-chemical parameters and the nutrients of the study site, an evaluation of the effect of physico-chemical parameters on cyanobacterial distribution and abundance, isolation, identification and culturing of cyanobacteria, the biochemical composition an productivity of cyanobacteria, and an evaluation of the potential of the selected cyanobacteria as antioxidants against ethanol induced lipid peroxidation. The pH, salinity and nutritional requirements were optimized for low-cost production of the selected cyanobacterial strains. The present study provides an insight into the distribution, abundance, diversity and ecology of cyanobacteria of Cochin estuary. From the results, it is evident that the ecological conditions of Cochin estuary support a rich cyanobacterial growth.

STUDIES ON TAXONOMY, DISTRIBUTION, ECOLOGY AND REPRODUCTIVE POTENTIAL OF ROTIFERS FROM SELECTED CENTRES IN COCHIN BACKWATER SYSTEM, KERALA

The studies were conducted in nine stations with varying ecological characteristics along Cochin backwaters and adjoining canals. Many workers opined that the distribution of rotifers is cosmopolitan. The significance of rotifers as first food for early larvae was indicated by Fujita. Aquaculture is a fast growing field in fisheries sector and it is gaining more importance as the fish landings and supply are getting irregular. A consistent supply of fish/shellfish can only be achieved through aquaculture. The success of any culture activity depends on the timely production of seeds of finfishes/shellfishes. The availability of wild seed is seasonal and erratic. So, a dependable source of seed of fishes and shellfishes is possible only through large scale production in hatchery. A successful seed production activity depends on the availability of a variety of suitable live feed organisms in sufficient quantities at the proper time for use in the larval stages. As the live feeds promote high growth rates, easy digestion, assimilation and the quality of not contaminating the culture water when compared to other artificial feeds, make the culture of live feed organisms the principal means of providing food for the larvae of finfishes and shellfishes. Rotifers are considered to be an excellent and indispensable food for larvae of many finfishes and crustaceans. It (1960) was the first to culture Brachionus plicatilis for feeding marine fish larvae, and now it is being extensively used as live feed in hatcheries all over the world. They are a group of microscopic organisms coming under the Phylum Rotifera which comprises of about 2000 species. Their slow swimming habits, ability to tolerate a wide range of salinities, parthenogenetic mode of reproduction and ability to get enriched easily, make rotifers an ideal live feed organism. The major factors such as temperature, salinity and food that influence the reproductive potential and thereby the population size of rotifer, Salinity is one of the most important aspect influencing the reproductive rate of rotifers. The feed type and feed concentration play a vital role in influencing the reproductive rate of rotifers. For culture of rotifers, the commonly used micro algae belong to Chlorella, Nannochloropsis, Isochrysis and Tetraselmis. While some studies have suggested that, algal diet has little effect on reproductive rates in 1979 while using the rotifer, Brachionus plicatilis as feed for the larvae of red sea bream, Pagrus major. It is generally accepted that rotifers play a pivotal role in the successful rearing of marine fish larvae.

L-Glutaminase production by an immobilized marine Pseudomonas sp. BTMS -51

The present study is about the Pseudomonas sp. BTMS-51 isolated from the marine sediments of Cochin Coast. In the present study, it is concluded that marine bacteria are ideal candidates for immobilization using either Ca-alginate entrapment or physical adsorption on to synthetic inert supports and the process of immobilization does not negatively influence them. Thus, Ca-alginate entrapment of the bacteria was found to be well suited for reuse of the biomass and extended operational stability during continuous operation. Adherence of the bacterium to inertsupports was observed to be strong and it imparted minimal stress on the immobilized bacterium and allowed detachment and relocation on the supports which enabled the formation of a dynamic equilibrium maintaining a stable cell loading. This is particularly desirable in the industry for extended operational stability and maintenance of consistently higher outputs. Marine Pseudomonas sp. BTMS-51 is ideal for industrial production of extra cellular L-glutaminase and immobilization on to synthetic inert support such as polyurethane foam could be an efficient technique, employing packed bed reactor for continuous production of the enzyme. Temperature and glutamine concentration had significant effects on enzyme production by cells immobilized on polyurethane foam (PUF).

Surface Active Substances in the Cochin Estuarine System

This study focuses on the fractionation and quantification of chlorophenols, the most important and potential pollutant in this category, the distribution and seasonal dynamics of MBAS, phenols and clorophenols and development of a model to describe the chemical reactivity of the estuary are utilizing the dynamics of boron. The CES is highly influenced by various anthropogenic activities like discharge of agricultural, industrial and urban wastes operation of shipyard, oil and other transporting activities, fishing, dredging etc. Seasonal values of MBAS showed high values in the surface water during monsoon compared to premonsoon and postmonsoon. In the Cochin estuary o-chlorophenol and p-chlorophenol showed low values in the surface water compared to bottom water in the northern part of the estuary and higher values in the surface water in the southern part

L-glutaminase production by marine fungi

This study presents the L-Glutaminase Production by Marine Fungi. Enzymes are involved in all aspects of biochemical conversion from the simple enzyme or fermentation conversion to the complex techniques in genetic engineering. Enzyme industry is one among the major industries of the world and there exists a great market for enzymes in general. Food industry is recognized as the largest consumer for commercial enzymes (Lon sane and Ramakrishna, 1989). In industry, enzymes are frequently used for process improvement, for instance to enable the utilization of new types of raw materials or for improving the physical properties of a material so that it can be more easily processed. They are the focal point of biotechnological processe. The marine biosphere is one of the richest of the earth's innumerable habitats, yet is one of the least well characterized. The marine biosphere covers more than two third of the world's surface, our knowledge of marine microorganisms, in particular fungi, is still very limited (Molitoris and Schumann, 1986). The results obtained in the present study the following conclusions are drawn. Beauveria bassiana isolated form marine sediment has immense potential as an Industrial organism for production of L-glutaminase as an extracellular enzyme employing either submerged fermentnation or solid state fermentation

Alkaline protease production by marine fungus engyodontium BTMFS 10

The thesis entitled “Alkaline Protease Production by Marine Fungus Engyodontium BTMFS 10”.Proteases are the single class of enzymes, which occupy a pivotal position with respect to their application in both physiological and commercial filed. Protease in the industrial market is expected to increase further in the coming year. The current trend is to use microbial enzymes since they provide a greater diversity of catalytic activities and can be produced more economically. Main objective of theses studies are the optimization of various physicochemical factors in the solid state fermentation for the production of alkaline protease enzyme, characterization of the enzyme, evaluation of the enzyme for various industrial application. The result obtained the during the course of theses study indicate the scope for the utilization of this study Marine Fungus E. Album for extra cellular protease production employing solid state fermentation