Clegg hammer measures and human external landing forces : is there a relationship?

Ground hardness is deemed an important consideration for player safety for sports played on natural turf surfaces. Currently, a ground hardness measure is being determined using a Clegg hammer, with the suitability for play dependent on an acceptable reading. This study aimed to examine whether a relationship between Clegg hammer readings and ground reaction forces (GRF’s) generated by a human during a drop landing exist. Fifteen male community level Australian football players were recruited for the study. Participants performed a single leg drop landing on the right leg from a 45cm box onto the force plate to record GRF’s. Ten trials were conducted for three conditions: no shock pad, thin shock pad (15mm) and thick shock pad (50mm) under a synthetic turf sample. Four consecutive Clegg hammer readings were recorded following each set of ten trials. Variables of interest were maximum vertical GRF (Max vGRF), maximum rate of loading (Max RoL) and Clegg hammer (CH) readings. Pearson’s Correlation Coefficient was conducted to examine the relationship between variables and conditions. Slight to fair relationships were found between the Max vGRF and any of the four CH drops (0.181 ≤r≥ 0.189; p ≤ 0.01). This finding was similar to the relationship with Max RoL (0.209 ≤r≥ 0.217; p ≤ 0.01). When analysed for the specific shock pad condition, the relationships remained poor (r <0.1; p ≥ 0.29), with the exception of the Max RoL and the CH readings on the thick shock pad (0.1 ≤r≥ 0.2; p ≥ 0.03). The results of this study show that the ground reaction forces experienced by a human on different levels of surface hardness are significantly different to the forces on impact of the Clegg hammer. Consequently, the Clegg hammer may not be the most appropriate device for relating surface hardness to player safety, thus it is possible that the Clegg hammer alone is insufficient in globally determining ground safety.

Best management practices for sustainable and safe playing surface of Australian Football League sports fields

In 2002, AFL Queensland and the Brisbane Lions Football Club approached the Department of Primary Industries and Fisheries (Queensland) for advice on improving their Premier League sports fields. They were concerned about player safety and dissatisfaction with playing surfaces, particularly uneven turf cover and variable under-foot conditions. They wanted to get the best from new investments in ground maintenance equipment and irrigation infrastructure. Their sports fields were representative of community-standard, multi-use venues throughout Australia; generally ‘natural’ soil fields, with low maintenance budgets, managed by volunteers. Improvements such as reconstruction, drainage, or regular re-turfing are generally not affordable. Our project aimed to: (a) Review current world practice and performance benchmarks; (b) Demonstrate best-practice management for community-standard fields; (c) Adapt relevant methods for surface performance testing; (d) Assess current soils, and investigate useful amendments; (e) Improve irrigation system performance; and (e) Build industry capacity and encourage patterns for ongoing learning. Most global sports field research focuses on elite, sand-based fields. We adjusted elite standards for surface performance (hardness, traction, soil moisture, evenness, sward cover/height) and maintenance programs, to suit community-standard fields with lesser input resources. In regularly auditing ground conditions across 12 AFLQ fields in SE QLD, we discovered surface hardness (measured by Clegg Hammer) was the No. 1 factor affecting player safety and surface performance. Other important indices were turf coverage and surface compaction (measured by penetrometer). AFLQ now runs regularly audits affiliated fields, and closes grounds with hardness readings greater than 190 Gmax. Aerating every two months was the primary mechanical practice improving surface condition and reducing hardness levels to < 110 Gmax on the renovated project fields. With irrigation installation, these fields now record surface conditions comparable to elite fields. These improvements encouraged many other sporting organisations to seek advice / assistance from the project team. AFLQ have since substantially invested in an expanded ground improvement program, to cater for this substantially increased demand. In auditing irrigation systems across project fields, we identified low maintenance (with < 65% of sprinklers operating optimally) as a major problem. Retrofitting better nozzles and adjusting sprinklers improved irrigation distribution uniformity to 75-80%. Research showed that reducing irrigation frequency to weekly, and preparedness to withhold irrigation longer after rain, reduced irrigation requirement by 30-50%, compared to industry benchmarks of 5-6 ML/ha/annum. Project team consultation with regulatory authorities enhanced irrigation efficiency under imposed regional water restrictions. Laboratory studies showed incorporated biosolids / composts, or topdressed crumb rubber, improved compaction resistance of soils. Field evaluations confirmed compost incorporation significantly reduced surface hardness of high wear areas in dry conditions, whilst crumb rubber assisted turf persistence into early winter. Neither amendment was a panacea for poor agronomic practices. Under the auspices of the project Trade Mark Sureplay®, we published > 80 articles, and held > 100 extension activities involving > 2,000 participants. Sureplay® has developed a multi-level curator training structure and resource materials, subject to commercial implementation. The partnerships with industry bodies (particularly AFLQ), frequent extension activities, and engagement with government/regulatory sectors have been very successful, and are encouraged for any future work. Specific aspects of sports field management for further research include: (a) Understanding of factors affecting turf wear resistance and recovery, to improve turf persistence under wear; (b) Simple tests for pinpointing areas of fields with high hardness risk; and (c) Evaluation of new irrigation infrastructure, ‘water-saving’ devices, and irrigation protocols, in improving water use and turf cover outcomes.

EVALUATION OF INTELLIGENT COMPACTION CONTROL IN THE M-189 RECONSTRUCTION PROJECT AT IRON RIVER, MICHIGAN

This research evaluated an Intelligent Compaction (IC) unit on the M-189 highway reconstruction project at Iron River, Michigan. The results from the IC unit were compared to several traditional compaction measurement devices including Nuclear Density Gauge (NDG), Geogauge, Light Weight Deflectometer (LWD), Dynamic Cone Penetrometer (DCP), and Modified Clegg Hammer (MCH). The research collected point measurements data on a test section in which 30 test locations on the final Class II sand base layer and the 22A gravel layer. These point measurements were compared with the IC measurements (ICMVs) on a point-to-point basis through a linear regression analysis. Poor correlations were obtained among different measurements points using simple regression analysis. When comparing the ICMV to the compaction measurements points. Factors attributing to the weak correlation include soil heterogeneity, variation in IC roller operation parameters, in-place moisture content, the narrow range of the compaction devices measurement ranges and support conditions of the support layers. After incorporating some of the affecting factors into a multiple regression analysis, the strength of correlation significantly improved, especially on the stiffer gravel layer. Measurements were also studied from an overall distribution perspective in terms of average, measurement range, standard deviation, and coefficient of variance. Based on data analysis, on-site project observation and literature review, conclusions were made on how IC performed in regards to compaction control on the M-189 reconstruction project.

Non-contact ACL injuries : association with clegg soil impact test values for sports fields, soil moisture and prevailing weather

Introduction: There is a recognised relationship between dry weather conditions and increased risk of anterior cruciate ligament (ACL) injury. Previous studies have identified 28 day evaporation as an important weather-based predictor of non-contact ACL injuries in professional Australian Football League matches. The mechanism of non-contact injury to the ACL is believed to increased traction and impact forces between footwear and playing surface. Ground hardness and the amount and quality of grass are factors that would most likely influence this and are inturn, related to the soil moisture content and prevailing weather conditions. This paper explores the relationship between soil moisture content, preceding weather conditions and the Clegg Soil Impact Test (CSIT) which is an internationally recognised standard measure of ground hardness for sports fields. Methodology: The 2.25 kg Clegg Soil Impact Test and a pair of 12 cm soil moisture probes were used to measure ground hardness and percentage moisture content. Five football fields were surveyed at 13 prescribed sites just before seven football matches from October 2008 to January 2009 (an FC Women’s WLeague team). Weather conditions recorded at the nearest weather station were obtained from the Bureau of Meteorology website and total rainfall less evaporation was calculated for 7 and 28 days prior to each match. All non-contact injuries occurring during match play and their location on the field were recorded. Results/conclusions: Ground hardness varied between CSIT 5 and 17 (x10G) (8 is considered a good value for sports fields). Variations within fields were typically greatest in the centre and goal areas. Soil moisture ranged from 3 to 40% with some fields requiring twice the moisture content of others to maintain similar CSIT values. There was a non-linear, negative relationship for ground hardness versus moisture content and a linear relationship with weather (R2, of 0.30 and 0.34, respectively). Three non-contact ACL injuries occurred during the season. Two of these were associated with hard and variable ground conditions.

A right of resale? Indigenous art under the hammer

This week, Sotheby's sold the late Clifford Possum Tjapaltjarri's painting, Warlugulong. The auction-house's spokesman, Tim Klingender, was enthusiastic about the high price commanded by the art work: "The painting was a really great painting and it deserved to make a really fantastic price, and it made that price."

Experimental investigation of die wear in small-batch hammer-forging under unlubricated conditions

Wear of dies is a serious problem in the forging industry. The materials used for the dies are generally expensive steel alloys and the dies require costly heat treatment and surface finishing operations. Degeneration of the die profile implies rejection of forged components and necessitates resinking or replacement of the die. Measures which reduce wear of the die can therefore aid in the reduction of production costs. The work reported here is the first phase of a study of the causes of die wear in forging production where the batch size is small and the machine employed is a light hammer. This is a problem characteristic of the medium and small scale area of the forging industry where the cost of dies is a significant proportion of the total capital investment. For the same energy input and under unlubricated conditions, die wear has been found to be sensitive to forging temperature; in cold forging the yield strength of the die material is the prime factor governing the degeneration of the die profile, whilst in hot forging the wear resistance of the die material is the main factor which determines the rate of die wear. At an intermediate temperature, such as that characteristic of warm forging, the die wear is found to be less than that in both cold and hot forging. This preliminary study therefore points to the fact that the forging temperature must be taken into account in the selection of die material. Further, the forging industry must take serious note of the warm forging process, as it not only provides good surface finish, as claimed by many authors, but also has an inherent tendency to minimize die wear.

When all you have is a hammer ...: RCTs and hegemony in science

People diagnosed with autism spectrum disorder (ASD) deserve the same respect as any other person and should be free to benefit from scientific research that can help them achieve skills which enable them to reach their full potential. Over the past 40 years Applied Behaviour Analysis (ABA) has utilised inductive, natural science methods to investigate techniques for the analysis and augmentation of socially significant behaviours. Unfortunately, many individuals with ASD in the UK cannot avail of these techniques because of an obdurate reliance on randomised controlled trials (RCTs) as the single most respectable measure of effectiveness of interventions. In this paper we focus on how the debate about RCTs is played out in the ‘autism wars’.

Distribution of potential suitable hammers and transport of hammer tools and nuts by wild capuchin monkeys

Selection and transport of objects to use as tools at a distant site are considered to reflect planning. Ancestral humans transported tools and tool-making materials as well as food items. Wild chimpanzees also transport selected hammer tools and nuts to anvil sites. To date, we had no other examples of selection and transport of stone tools among wild nonhuman primates. Wild bearded capuchins (Cebus libidinosus) in Boa Vista (Piaui, Brazil) routinely crack open palm nuts and other physically well-protected foods on level surfaces (anvils) using stones (hammers) as percussive tools. Here we present indirect evidence, obtained by a transect census, that stones suitable for use as hammers are rare (study 1) and behavioral evidence of hammer transport by twelve capuchins (study 2). To crack palm nuts, adults transported heavier and harder stones than to crack other less resistant food items. These findings show that wild capuchin monkeys selectively transport stones of appropriate size and hardness to use as hammers, thus exhibiting, like chimpanzees and humans, planning in tool-use activities.

The relationship between pre-sale price estimates and the hammer price for Australian paintings sold at auction

Realized price for paintings auctioned can systematically differ from prior estimates. We need to understand why experts get it wrong. This paper uses an econometric approach to investigate how pre-sales price estimates are formed and the impact that they have in determining auction prices for Australian paintings.

Avaliação da aplicabilidade do modelo de maturidade de Michael Hammer para gestão de processos em tecnologia da informação

O termo gestão de processos vem ganhando relevância como forma de gestão dentre as principais organizações em todo o mundo. entretanto o assunto ainda é recente no Brasil. O aumento de demandas relacionadas a este tema gerou inúmeras tecnologias de suporte a sua gestão. o que leva as empresas à necessidade de compreenderem melhor o tema. Michael Hammer propôs um modelo de maturidade em gestão de processos. que além de proporcionar subsídios aos executivos para tomadas de decisão. permite que os envolvidos tenham uma melhor compreensão do nível de maturidade de sua organização. Este trabalho teve como objetivo estudar a viabilidade da aplicação do modelo de maturidade de Michael Hammer. usando como caso prático a área de Tecnologia da Informação de uma grande empresa brasileira. As informações para análise foram compostas por questionários e entrevistas. revisão documental e observação direta. Os resultados obtidos confirmam a importância da compreensão do nível de maturidade da organização para início ou melhoria da gestão de processos. Apesar do estudo confirmar a aplicabilidade do modelo. existem ressalvas importantes a serem consideradas por qualquer área ou organização de TI que queira medir o nível de maturidade em gestão de processos através do modelo proposto.