Thermal analysis of the chip formation in austenitic stainless steel

The most important property of austenitic stainless steels is corrosion resistance. In these steels, the transition between paramagnetic and ferromagnetic conditions occurs at low temperatures. Therefore, the use of austenitic stainless steels in conditions in which ferromagnetism absence is important can be considered. On the other hand, the formation of strain-induced martensite is detected when austenitic stainless steels are deformed as well as machined. The strain-induced martensite formed especially in the machining process is not uniform through the chip and its formation can also be related to the Md temperature. Therefore, both the temperature distribution and the gradient during the cutting and chip formation are important to identify regions in which martensite formation is propitiated. The main objective here is evaluate the strain-induced martensite formation throughout machining by observing microstructural features and comparing these to thermal results obtained through finite element method analysis. Results show that thermal analysis can give support to the martensite identified in the microstructural analysis.

Machining Unidirectional Composites using Single-Point Tools : Analysis of Cutting Forces, Chip Formation and Surface Integrity

Peer reviewed

Cutting of Frozen Wood

The objective of this master's thesis was to develop a system for measuring the cutting forces of frozen wood. In northern parts of the world cuttingof frozen wood is one of the major problem. During winter and early spring the temperature inside the wood cells will fall below Zero degrees that strongly influences on the properties of the wood. These variations of properties will effects on the blade nomenclature while cutting the frozen wood. However the end results will cause uneven cutting forces. Cutting forces, Chip formation, wearing of the blade and the quality of the machined surface are difficult task. In this project we are attempting to find the variation of cutting forces and properties of frozen wood at four different temperatures (-20 , -10, 0 and + 10 degrees). The linear planning machine was used for measuring the cuttingforces. The cutting was done parallel to the long axis of wood due to the nature of pine wood and the structure of the plane. A considerable amount of work andtime was used for collecting and processing the numerical information from the sensors of the measuring system. There were some alterations suggested to the construction of the plane and the sensor system.

Lastunmuodostus jäätyneen ja sulan puun pyörösahauksessa

Tämän tutkimuksen tavoitteena oli selvittää eri parametrien vaikutusta lastunmuodostukseen pyörösahattaessa jäätynyttä ja sulaa puuta. Tutkimuksessa vertailtiin erityisesti jäätyneen ja sulan puun eroja sahauksen kannalta. Lisäksi tutkittiin puruvuodon esiintymistä pyörösahauksessa. Tutkimuksen empiirisessä osassa tutkittiineri parametrien vaikutusta sahauksen maksimitehoon, lastujen kokojakaumaan sekälastunmuodostukseen. Lastunmuodostusta kuvattiin videokameralla erittäin nopealla suljinajalla ja syntyneitä videokuvia arvioitiin silmämääräisesti. Mittaustenperusteella havaittiin, että jäätyneen ja sulan puun eroavaisuudet pyörösahauksessa ovat melko pienet. Lisäksi saatiin määritettyä muiden käytettyjen muuttujien vaikutukset puun pyörösahauksessa. Tutkimuksessa havaittiin myös, että puun sisäisillä ominaisuuksilla on erittäin suuri vaikutus sahausprosessiin.

Järjestelmä puun työstövoimien mittaamiseksi

Diplomityössä oli tavoitteena kehittää järjestelmää puun leikkuuvoimien mittaamiseksi. Puun leikkuuvoima, lastun muodostus, terien kuluminen ja työstöjälki ovat tekijöitä, jotka kiinnostavat puun työstön kanssa tekemisissä olevia tahoja. Luonnonmateriaalina puu on erittäin epähomogeenista, mikä vaikeuttaa luotettavien ja tarkkojen mittaustulosten saavuttamista. Mittauksia vaikeuttavia tekijöitä ovat muun muassa puun tiheysvaihtelut, poikkeamat syysuunnassa sekä oksat. Leikkuuvoimien mittaamisessa käytettiin lineaarihöylää. Höylän rakenteesta ja toimintaperiaatteesta sekä puumateriaalin luonteesta johtuen höyläykset tehtiin ainoastaan puun pituussuunnassa. Huomattavan osan työstä muodosti anturoinnilta tulevan mittaustiedon taltiointiin ja muokkaamiseen liittyvät kysymykset. Mittausjärjestelmän testaamisen ja tehtyjen koemittausten perusteella päädyttiin ehdottamaan muutamia muutoksia sekä itse höylään että mittausanturointiin.

M-käsittelyn vaikutus lastuamalla valmistettavan tuotteen valmistuskustannuksiin

Paremmin lastuttavia M-käsiteltyjä teräksiä on käytetty yrityksissä jo yli 20 vuoden ajan. Ominaisuuksiensa ansiosta M-teräksillä on pystytty pienentämään koneistuskustannuksia ja parantamaan kilpailukykyä. Viime vuosien aikana lastuavat terät ja työstökoneet ovat kuitenkin kehittyneet ja ero M-terästen ja tavanomaisten terästen välillä on voinut kaventua. Tämän diplomityön tavoitteena oli tutkia, saavutetaanko M-teräksen käytöllä taloudellisia etuja nykyaikaisissa konepajaolosuhteissa. Tutkimuksessa vertailtiin M-käsitellyn ja tavanomaisen 42CrMo4 – teräksen koneistusta. Valmistuskokeissa tarkasteltiin terien kulumista, lastun muotoa ja pinnanlaatua. Koekappaleena toimi olakkeellinen kuusiomutteri M64 kierteellä. Tuotteita valmistettiin yli 500 kappaletta ja materiaalia poistettiin noin 2000 kg. Koetulosten perusteella tuotteille laskettiin koneistuskustannukset kuvitteellisessa yrityksessä. Ero materiaalien välillä oli suurin työvaiheissa, joissa lastuaminen oli jatkuvaa. Sisä- ja ulkosorvauksessa M-käsiteltyä terästä lastunneiden terien kestoikä oli noin kaksinkertainen ja kierteen sorvauksessa noin nelinkertainen tavalliseen teräkseen verrattuna. Hakkaavassa työstössä terien kestoikä oli molemmilla materiaaleilla sama. Työssä suoritettujen kokeiden ja kustannuslaskelmien perusteella, käyttämällä M-käsiteltyä terästä voidaan pienentää valmistuskustannuksia. Materiaalien välinen ero korostuu, kun hakkaavaa työstöä on vähän, sarjat ovat suuria ja tuotanto on miehittämätöntä.

On the numerical simulation of machining processes

Numerical simulation of machining processes can be traced back to the early seventies when finite element models for continuous chip formation were proposed. The advent of fast computers and development of new techniques to model large plastic deformations have favoured machining simulation. Relevant aspects of finite element simulation of machining processes are discussed in this paper, such as solution methods, material models, thermo-mechanical coupling, friction models, chip separation and breakage strategies and meshing/re-meshing strategies.

Modelling Cutting States in Rough Turning of 34CrNiMo6 Steel

Rough turning is an important form of manufacturing cylinder-symmetric parts. Thus far, increasing the level of automation in rough turning has included process monitoring methods or adaptive turning control methods that aim to keep the process conditions constant. However, in order to improve process safety, quality and efficiency, an adaptive turning control should be transformed into an intelligent machining system optimizing cutting values to match process conditions or to actively seek to improve process conditions. In this study, primary and secondary chatter and chip formation are studied to understand how to measure the effect of these phenomena to the process conditions and how to avoid undesired cutting conditions. The concept of cutting state is used to address the combination of these phenomena and the current use of the power capacity of the lathe. The measures to the phenomena are not developed based on physical measures, but instead, the severity of the measures is modelled against expert opinion. Based on the concept of cutting state, an expert system style fuzzy control system capable of optimizing the cutting process was created. Important aspects of the system include the capability to adapt to several cutting phenomena appearing at once, even if the said phenomena would potentially require conflicting control action.

Effects of Milling on Surface Integrity of Low-Carbon Steel

This work measured the effect of milling parameters on the surface integrity of low-carbon alloy steel. The Variance Analysis showed that only depth of cut did not influence on the workpiece roughness and the Pearson's Coefficient indicated that cutting speed was more influent than tool feed. All cutting parameters introduced tensile residual stress in workpiece surface. The chip formation mechanism depended specially on cutting speed and influenced on the roughness and residual stress of workpiece.

Effects of milling condition on the surface integrity of hot forged steel

This paper presents a study on the influence of milling condition on workpiece surface integrity focusing on hardness and roughness. The experimental work was carried out on a CNC machining center considering roughing and finishing operations. A 25 mm diameter endmill with two cemented carbide inserts coated with TiN layer were used for end milling operation. Low carbon alloyed steel Cr-Mo forged at 1200 degrees C was used as workpiece on the tests. Two kinds of workpiece conditions were considered, i.e. cur cooled after hot forging and normalized at 950 degrees C for 2 h. The results showed that finishing operation was able to significantly decrease the roughness by at least 46% without changing the hardness. on the other hand, roughing operation caused an increase in hardness statistically significant by about 6%. The machined surface presented deformed regions within feed marks, which directly affected the roughness. Surface finish behavior seems to correlate to the chip ratio given the decrease of 25% for roughing condition, which damaged the chip formation. The material removal rate for finishing operation 41% greater than roughing condition demonstrated to be favorable to the heat dissipation and minimized the effect on material hardness.

Influence of the tool edge geometry on specific cutting energy at high-speed cutting

This paper presents specific cutting energy measurements as a function of the cutting speed and tool cutting edge geometry. The experimental work was carried out on a vertical CNC machining center with 7,500 rpm spindle rotation and 7.5 kW power. Hardened steels ASTM H13 (50 HRC) were machined at conventional cutting speed and high-speed cutting (HSC). TiN coated carbides with seven different geometries of chip breaker were applied on dry tests. A special milling tool holder with only one cutting edge was developed and the machining forces needed to calculate the specific cutting energy were recorded using a piezoelectric 4-component dynamometer. Workpiece roughness and chip formation process were also evaluated. The results showed that the specific cutting energy decreased 15.5% when cutting speed was increased up to 700%. An increase of 1 °in tool chip breaker chamfer angle lead to a reduction in the specific cutting energy about 13.7% and 28.6% when machining at HSC and conventional cutting speed respectively. Furthermore the workpiece roughness values evaluated in all test conditions were very low, closer to those of typical grinding operations (∼0.20 μm). Probable adiabatic shear occurred on chip segmentation at HSC Copyright © 2007 by ABCM.

Analysis on turning Ti-6Al-4V with different cooling methods

The aim of this paper is to optimize the machining of Ti-6Al-4V alloy, by studying the chip formation, roughness and tool wear for different cooling conditions. The results were compared between cooling methods, minimal quantity of fluid (MQF) and flooding, and also without fluid for the tool H13A. The turning of Ti-6Al-4V has shown good results on roughness (0, 8μm) and tool life, which was 11% lower with MQF than with the flooding method. The tool wear causes variation of the shear angle, which promotes strength hardening of the chip. As a result, the machined surface could be damaged. The use of the cutting fluid helps to save the cutting edge and could reduce the strength hardening. Nevertheless, it could also facilitate the formation of built-up edge. The nucleation of alpha lamellar colonies can occur due to a combination of deformation rates and temperature, mainly when the flooding is used, but it's not conclusive. The lamellar colonies were also found with the MQF in some regions, however, this structure did not show hardness variation compared to equiaxial. For all this reasons, the machining parameters might be carefully chosen.

A valiação da integridade superficial e usinabilidade de engrenagens forjadas utilizando fresamento com alta velocidade de corte

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo dos mecanismos governantes do efeito de escala na microusinagem

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito do fresamento com alta velocidade de corte na usinabilidade de aços ferríticos com grãos ultrafinos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)