Alkaline treatment of the cellulose fiber affecting membrane column behaviour for high-performance immunoaffinity chromatography

The original cellulose fibers and those treated by alkaline solution were both used to prepare the acrylic membranes. The two kinds of membranes were packed into the columns for high-performance immunoaffinity chromatography by the immobilization of protein A on them. It was observed that the alkaline treatment of the cellulose fiber decreased the pressure resistance of the membrane to the mobile phases and greatly increased the accessible volume to the proteins, but affected the adsorption capacity of human IgG on the protein A membrane columns less. There is little difference between those two kinds of membranes on the adsorption capacities of HIgG, which means that the alkaline treatment of the cellulose fiber only significantly changes the void volume inter-membrane, and the porosity and surface area of membrane less. Alkaline treatment of the cellulose fiber reduced the membrane-column efficiency significantly. Some typical examples for the immunoaffinity analysis of IgG from human and dog plasma on the protein A membrane columns are illustrated. Copyright (C) 2000 John Wiley & Sons, Ltd.

Chitosan, sisal cellulose, and biocomposite chitosan/sisal cellulose films prepared from thiourea/NaOH aqueous solution

Environmentally friendly biocomposites were successfully prepared by dissolving chitosan and cellulose in a NaOH/thiourea solvent with subsequent heating and film casting. Under the considered conditions, NaOH/thiourea led to chain depolymerization of both biopolymers without a dramatic loss of film forming capacities. Compatibility of both biopolymers in the biocomposite was firstly assessed through scanning electron microscopy, revealing an intermediate organization between cellulose fiber network and smoothness of pure chitosan. DSC analyses led to exothermic peaks close to 285 and 315 degrees C for the biocomposite, compared to the exothermic peaks of chitosan (275 degrees C) and cellulose (265 and 305 degrees C), suggesting interactions between chitosan and cellulose. Contact angle analyses pointed out the deformation that can occur at the surface due to the high affinity of the;e materials with water. T(2) NMR relaxometry behavior of biocomposites appeared to be dominated by chitosan. Other properties of films, as crystallinity, water sorption isotherms, among others, are also discussed. (C) 2010 Published by Elsevier Ltd.

NOVEL CELLULOSE/NbOPO4 center dot nH(2)O HYBRID MATERIAL FROM SUGARCANE BAGASSE

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Novel cellulose/NbOPO 4.nH 2O hybrid material from sugarcane bagasse

In recent years studies concerning the applications of lignocellulosic/ inorganic couples have resulted in the development of an interesting class of functional materials. In this work a cellulose/NbOPO 4.nH 2O hybrid using cellulose from surgacane bagasse was prepared and characterized in order to test for adsorption applications. The preparation process was conducted by carrying out metallic niobium dilution in hydrofluoric acid in the presence of nitric acid, then adding boric acid to form the complex and, finally, the cellulose sugar cane bagasse was added. Concentrated phosphoric acid was also inserted to precipitate hydrous niobium phosphate particles in the cellulose fiber. This material was characterized by X-ray diffractometry (XRD), thermogravimetry (TG/DTG), and scanning electronic microscopy (SEM) connected to an energy dispersive spectrophotometer (EDS). Results by SEM/EDS show that NbOPO 4.nH 2O was present in structure of the cellulose. During the preparation of the material, using boric acid it was observed that the formation of precipitate occurred in a shorter time than the material prepared without boric acid.

Dietary fiber as fat substitute in emulsified and cooked meat model system

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Stone Weathering in the Monastic Building Complex on Mountain of St Aaron in Petra, Jordan.

Since 1997 the Finnish Jabal Haroun Project (FJHP) has studied the ruins of the monastery and pilgrimage complex (Gr. oikos) of Aaron located on a plateau of the Mountain of Prophet Aaron, Jabal an-Nabi Harûn, ca. 5 km to the south-west of the UNESCO World Heritage site of Petra in Jordan. The state of conservation and the damaging processes affecting the stone structures of the site are studied in this M.A. thesis. The chapel was chosen as an example, as it represents the phasing and building materials of the entire site. The aim of this work is to act as a preliminary study with regards to the planning of long-term conservation at the site. The research is empirical in nature. The condition of the stones in the chapel walls was mapped using the Illustrated Glossary on Stone Deterioration, by the ICOMOS International Scientific Committee for Stone. This glossary combines several standards and systems of damage mapping used in the field. Climatic conditions (temperature and RH %) were monitored for one year (9/2005-8/2006) using a HOBO Microstation datalogger. The measurements were compared with contemporary measurements from the nearest weather station in Wadi Musa. Salts in the stones were studied by taking samples from the stone surfaces by scraping and with the “Paper Pulp”-method; with a poultice of wet cellulose fiber (Arbocel BC1000) and analyzing what main types of salts were to be found in the samples. The climatic conditions on the mountain were expected to be rapidly changing and to differ clearly from conditions in the neighboring areas. The rapid changes were confirmed, but the values did not differ as much as expected from those nearby: the 12 months monitored had average temperatures and were somewhat drier than average. Earlier research in the area has shown that the geological properties of the stone material influence its deterioration. The damage mapping showed clearly, that salts are also a major reason for stone weathering. The salt samples contained several salt combinations, whose behavior in the extremely unstable climatic conditions is difficult to predict. Detailed mapping and regular monitoring of especially the structures, that are going remain exposed, is recommended in this work.

Nanoscale studies of materials using x-ray synchrotron radiation and mesoscopic modelling

X-ray synchrotron radiation was used to study the nanostructure of cellulose in Norway spruce stem wood and powders of cobalt nanoparticles in cellulose support. Furthermore, the growth of metallic clusters was modelled and simulated in the mesoscopic size scale. Norway spruce was characterized with x-ray microanalysis at beamline ID18F of the European Synchrotron Radiation Facility in Grenoble. The average dimensions and the orientation of cellulose crystallites was determined using x-ray microdiffraction. In addition, the nutrient element content was determined using x-ray fluorescence spectroscopy. Diffraction patterns and fluorescence spectra were simultaneously acquired. Cobalt nanoparticles in cellulose support were characterized with x-ray absorption spectroscopy at beamline X1 of the Deutsches Elektronen-Synchrotron in Hamburg, complemented by home lab experiments including x-ray diffraction, electron microscopy and measurement of magnetic properties with a vibrating sample magnetometer. Extended x-ray absorption fine structure spectroscopy (EXAFS) and x-ray diffraction were used to solve the atomic arrangement of the cobalt nanoparticles. Scanning- and transmission electron microscopy were used to image the surfaces of the cellulose fibrils, where the growth of nanoparticles takes place. The EXAFS experiment was complemented by computational coordination number calculations on ideal spherical nanocrystals. The growth process of metallic nanoclusters on cellulose matrix is assumed to be rather complicated, affected not only by the properties of the clusters themselves, but essentially depending on the cluster-fiber interfaces as well as the morphology of the fiber surfaces. The final favored average size for nanoclusters, if such exists, is most probably a consequence of these two competing tendencies towards size selection, one governed by pore sizes, the other by the cluster properties. In this thesis, a mesoscopic model for the growth of metallic nanoclusters on porous cellulose fiber (or inorganic) surfaces is developed. The first step in modelling was to evaluate the special case of how the growth proceeds on flat or wedged surfaces.

Composição química do capim-elefante cv. Roxo cortado em diferentes alturas

O objetivo deste trabalho foi verificar o efeito dos cortes efetuados a 0, 15, 30 e 45 cm sobre a composição química do capim-elefante (Pennisetum purpureum, Schum.) cv. Roxo, em épocas seca e chuvosa. As amostras foram obtidas de uma área útil de 8,4 m² de cada parcela. Após o corte de uniformização, efetuaram-se dois cortes no período seco, em intervalos de 90 dias, e três no período chuvoso, em intervalos de 60 dias. de cada parcela foi tomada uma amostra de 3 a 5 perfilhos, desidratada em estufa e triturada para analises laboratoriais. Foram avaliados os percentuais de matéria seca (MS), proteína bruta (PB), fibra em detergente neutro (FDN), fibra em detergente ácido (FDA), celulose (CEL), hemicelulose (HCEL), lignina (LIG) e cinzas. As alturas de corte não influenciaram a composição química da forrageira, nem houve interação com as épocas. Com exceção de hemicelulose e cinzas, os cortes na época seca mostraram resultados superiores à chuvosa. As médias nas duas épocas foram 19,70 e 17,44% para MS; 7,74 e 7,25% para PB; 76,41 e 71,13% para FDN; 42,75 e 41,02% para FDA; 31,44 e 30,43% para CEL; 30,66 e 30,28% para HCEL; 9,25 e 7,83% para LIG; e 1,97 e 3,38% para cinzas, nos períodos seco e chuvoso, respectivamente.

Bacterial nanocellulose for medical implants

Bacterial cellulose (BC) has established to be a remarkably versatile biomaterial and can be used in wide variety of applied scientific endeavours, especially for medical devices. In fact, biomedical devices recently have gained a significant amount of attention because of an increased interest in tissue-engineered products for both wound care and the regeneration of damaged or diseased organs. Due to its unique nanostructure and properties, microbial cellulose is a natural candidate for numerous medical and tissue-engineered applications. Hydrophilic bacterial cellulose fibers of an average diameter of 50 nm are produced by the bacterium Acetobacter xylinum, using a fermentation process. The microbial cellulose fiber has a high degree of crystallinity. Using direct nanomechanical measurement, determined that these fibers are very strong and when used in combination with other biocompatible materials, produce nanocomposites particularly suitable for use in human and veterinary medicine. Moreover, the nanostructure and morphological similarities with collagen make BC attractive for cell immobilization and cell support. The architecture of BC materials can be engineered over length scales ranging from nano to macro by controlling the biofabrication process. The chapter describes the fundamentals, purification and morphological investigation of bacterial cellulose. This chapter deals with the modification of microbial cellulose and how to increase the compatibility between cellulosic surfaces and a variety of plastic materials. Furthermore, provides deep knowledge of fascinating current and future applications of bacterial cellulose and their nanocomposites especially in the medical field, materials with properties closely mimic that of biological organs and tissues were described. © Springer-Verlag Berlin Heidelberg 2013.

Estudo do comportamento coloidal de suspensão de fibra de celulose, carbonato de cálcio, amido catiônico: variação da força iônica e do pH

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito das farinhas de jatobá-do-cerrado (Hymenaea stigonocarpa Mart.) in natura e extrusada no metabolismo lipídico e parâmetros fermentativos em hamsters e resposta glicêmica em humanos após a extrusão

Introdução: A polpa farinácea do jatobá-do-cerrado (Hymenaea stigonocarpa Mart.) apresenta alto teor de fibra alimentar, em média 60 g/100 g, que são importantes para a redução do risco e controle de doenças crônicas não transmissíveis (DCNT). A extrusão termoplástica neutraliza aromas intensos, proporciona a formação de amido resistente, aumenta a fibra alimentar solúvel e melhora a textura do produto final. Objetivo: Estudar o efeito das farinhas de jatobá-do-cerrado in natura (FIN) e extrusada (FE) no metabolismo lipídico e parâmetros fermentativos em hamsters, bem como verificar a resposta glicêmica em humanos após a extrusão. Métodos: Processo de extrusão: velocidade de 200 rpm; matriz com 4 mm de diâmetro; taxa de compressão 3:1; alimentação constante de 70 gramas/minuto; temperatura de 150 °C; proporção farinha de jatobá-do-cerrado e amido de milho: 70:30 por cento e umidade a 25 por cento . Foi realizado um experimento animal com hamsters durante 21 dias, em que se analisou alguns parâmetros do metabolismo lipídico e colônico (fermentativos) dos animais, divididos em quatro grupos experimentais, se diferenciando pela dieta. As dietas controle (GC), in natura (GFI) e extrusada (GFE) eram hipercolesterolemizantes (13,5 por cento de gordura de coco e 0,1 por cento de colesterol) e a dieta referência (GR) com óleo de soja como fonte lipídica, não. Todas as dietas apresentavam 15 por cento de fibra alimentar, sendo que as dietas GR e GC tinham como fonte de fibra a celulose, e as dietas GFI e GFE tiveram as próprias fibras como fonte. A resposta glicêmica em humanos foi verificada por meio do ensaio do índice glicêmico e carga glicêmica da FE, com dez voluntários saudáveis que consumiram 25 gramas de carboidratos disponíveis do alimento teste (farinha extrusada) ou do pão branco como alimento controle. Resultados: Não foi observada diferença significativa entre o peso final, ingestão diária média e total, ganho de peso e CEA entre os animais dos quatro grupos. A concentração de triglicerídeos foi menor em 41 por cento e 38 por cento nos animais que receberam as dietas GFI e GFE, em relação aqueles que receberam a dieta GC, assim como também para o colesterol total (55 por cento e 47 por cento ), LDL-c (70 por cento e 53 por cento ) e não-HDL-c (63 por cento e 49 por cento ) séricos, lipídeos totais hepáticos (39 por cento e 45 por cento ) e o peso dos fígados dos animais também foi menor (21 por cento em ambos os grupos). Não houve diferença no colesterol hepático e excretado nas fezes dos animais dos quatro grupos. Os animais do GFE excretaram 57 por cento mais ácidos biliares nas fezes que os animais do GC. Com relação aos parâmetros fermentativos, observou-se maior excreção de fibras (1,24 ± 0,08 e 1,52 ± 0,09 gramas) nos animais dos grupos GR e GC respectivamente, em relação aos do GFI e GFE (0,50 e 0,48 gramas), porém o escore fecal (3,50 ± 0,19 e 3,38 ± 0,18) e o grau de fermentação (54 e 52 por cento ) foi maior nos animais dos grupos GFI e GFE. Houve uma maior produção de AGCC no ceco dos animais dos grupos GFI e GFE (80 e 57,5 µmol/g de ceco respectivamente) e maior diminuição do pH no conteúdo cecal nos animais do grupo GFI (7,49 ± 0,10), em relação ao GC (8,06 ± 0,13). Os ácidos acético e propiônico, estiveram presentes em maior quantidade no ceco dos animais dos grupos GFI (58,5 e 6,1 µmol/g de ceco) e GFE (42,5 e 6,6 µmol/g de ceco) e os animais do GFI produziram mais ácido butírico (15 µmol/g de ceco), em relação aos demais grupos. Quanto à resposta glicêmica da farinha pós extrusão, não houve diferença entre a área de resposta glicêmica da farinha extrusada e do pão branco, o índice glicêmico da farinha extrusada (glicose como controle) foi classificado como moderado, e a carga glicêmica (na porção de 30 gramas), baixa. Conclusão: As FIN e FE favoreceram a redução do colesterol total, LDL-c, não-HDL-c e dos triglicerídeos séricos, além da diminuição do acúmulo de lipídeos hepáticos. Foi observado também aumento expressivo na formação de AGCC e no grau de fermentação. A FE proporcionou um aumento na excreção de ácidos biliares nas fezes e apresentou índice glicêmico moderado e baixa carga glicêmica.

MICROSCALE DIELECTRIC ANTI-REFLECTION COATINGS FOR PHOTOVOLTAICS

In order to power our planet for the next century, clean energy technologies need to be developed and deployed. Photovoltaic solar cells, which convert sunlight into electricity, are a clear option; however, they currently supply 0.1% of the US electricity due to the relatively high cost per Watt of generation. Thus, our goal is to create more power from a photovoltaic device, while simultaneously reducing its price. To accomplish this goal, we are creating new high efficiency anti-reflection coatings that allow more of the incident sunlight to be converted to electricity, using simple and inexpensive coating techniques that enable reduced manufacturing costs. Traditional anti-reflection coatings (consisting of thin layers of non-absorbing materials) rely on the destructive interference of the reflected light, causing more light to enter the device and subsequently get absorbed. While these coatings are used on nearly all commercial cells, they are wavelength dependent and are deposited using expensive processes that require elevated temperatures, which increase production cost and can be detrimental to some temperature sensitive solar cell materials. We are developing two new classes of anti-reflection coatings (ARCs) based on textured dielectric materials: (i) a transparent, flexible paper technology that relies on optical scattering and reduced refractive index contrast between the air and semiconductor and (ii) silicon dioxide (SiO2) nanosphere arrays that rely on collective optical resonances. Both techniques improve solar cell absorption and ultimately yield high efficiency, low cost devices. For the transparent paper-based ARCs, we have recently shown that they improve solar cell efficiencies for all angles of incident illumination reducing the need for costly tracking of the sun’s position. For a GaAs solar cell, we achieved a 24% improvement in the power conversion efficiency using this simple coating. Because the transparent paper is made from an earth abundant material (wood pulp) using an easy, inexpensive and scalable process, this type of ARC is an excellent candidate for future solar technologies. The coatings based on arrays of dielectric nanospheres also show excellent potential for inexpensive, high efficiency solar cells. The fabrication process is based on a Meyer rod rolling technique, which can be performed at room-temperature and applied to mass production, yielding a scalable and inexpensive manufacturing process. The deposited monolayer of SiO2 nanospheres, having a diameter of 500 nm on a bare Si wafer, leads to a significant increase in light absorption and a higher expected current density based on initial simulations, on the order of 15-20%. With application on a Si solar cell containing a traditional anti-reflection coating (Si3N4 thin-film), an additional increase in the spectral current density is observed, 5% beyond what a typical commercial device would achieve. Due to the coupling between the spheres originated from Whispering Gallery Modes (WGMs) inside each nanosphere, the incident light is strongly coupled into the high-index absorbing material, leading to increased light absorption. Furthermore, the SiO2 nanospheres scatter and diffract light in such a way that both the optical and electrical properties of the device have little dependence on incident angle, eliminating the need for solar tracking. Because the layer can be made with an easy, inexpensive, and scalable process, this anti-reflection coating is also an excellent candidate for replacing conventional technologies relying on complicated and expensive processes.

Cellulose acetate polymer film modified microstructured polymer optical fiber towards a nitrite optical probe

A novel microstructured polymer optical fiber (MPOF) probe for nitrites (NO(2)(-)) detection was made by forming rhodamine 6G (Rh 6G)-doped cellulose acetate (CA) on the side wall of array holes in a MPOF It was found that the MPOF probe only have a response to nitrites in a certain concentration of sulfuric acid solution The calibration graph of fluorescence intensity versus nitrites concentration was linear in the range of 2.0 x 10(-4) g/ml-5.0 x 10(-3) g/ml. The method possesses case of chemical modification, low cost design, and potential for direct integration with existing instrumentation, and has been applied to the determination of nitrites in real samples with satisfactory results. (C) 2010 Elsevier B.V. All rights reserved