Obtenção e caracterização físico-química de blendas poliméricas, baseadas em POE e PMMA, dopadas com dióxido de titânio

The study of polymer blends has been an alternative method in the search field of new materials for obtaining materials with improved properties. In this work blends of poly(methyl methacrylate) (PMMA) and poly(ethylene oxide) (PEO) doped with titanium dioxide (TiO2) were studied. The PEO is a polymer semicrystalline structure varying between, 70 and 84% crystallinity, while the PMMA exhibits behavior amorphous in their structure. The use of TiO2 is related to corrosion-resistant of titanium as well as good heat transfer and other characteristics. The study of these polymer blends doped TiO2 gives the properties junction organic (polymer) and inorganic (oxide) which leads to modification of the properties of the resultant material. The blends were doped TiO2 (POE/PMMA/TiO2) in different proportions of the PMMA with the PEO and TiO2 fixed. The ratios were: 90/10/0,1; 85/15/0, 1; 80/20/0,1, 75/25/0,1 and 70/30/0,1. The resulting material was obtained in powder form and being characterized by Fourier Transformed Infrared (FTIR) Spectroscopy, Scanning Electron Microscopy (SEM), X-Ray Diffraction (XRD), Thermogravimetric Analysis (TGA) and Electrochemical Impedance Spectroscopy (EIS). The infrared spectra (IR) for the blends in different ratios showed a band at 1744 cm-1, characteristic of the C=O stretching, which increases in intensity with increasing PMMA composition, while in the spectrum of pure PEO this band is absent. This may suggest that the interaction is occurring between the polymers. In the micrographs of the blends also observed change in their surfaces with variation of the composition of PMMA, contributing to the change of the electrical properties of the material. The EIS data showed that the material exhibited conductivity of the order of 10-6 S.cm-1. The blend in the ratio B2(85/15/0, 1) showed better conductivity, σ = 1.56 x 10-6 S.cm-1. It was observed that the diffusion coefficient for the blends, B5(70/30/0, 1) was the largest, 1.07 x 10-6 m2.s-1. The XRD data showing that, with the variation in the composition of the PMMA blend crystallinity of the material is decreased reaching a minimum B3(80/20/0,1), and then increases again. Thermal analysis suggests that blends made from the material obtained can be applied at room temperature

Desenvolvimento de biomateriais a partir de blendas poliméricas a base de amido

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Degradação de blendas poliméricas por microrganismos de solo e de chorume

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Blendas de polietileno de ultra alto peso molar (PEUAPM) com polietileno linear de média densidade (PELMD) para rotomoldagem

Neste trabalho foi feito um estudo das propriedades reológicas, mecânicas e térmicas de blendas poliméricas contendo 1 e 10% em massa de polietileno de ultra alto peso molar (PEUAPM) e polietileno linear de média densidade (PELMD). As blendas foram obtidas por mistura em extrusora de rosca simples e em extrusora de rosca dupla, para fins de comparação. Na extrusão em rosca dupla foi acrescentado um terceiro componente - óleo mineral, cera ou polietileno de muito baixo peso Molar (PEMBPM) - a fim de promover uma melhor interação entre o PELMD e PEUAPM. As amostras obtidas por moldagem por injeção, rotomoldagem e moldagem por compressão foram submetidas a testes reológicos, térmicos e mecânicos. Foi analisada a influência do tipo de processamento e da composição das blendas sobre morfologia e as propriedades finais destas. A reometria rotacional indicou um gradual aumento da viscosidade das blendas com o aumento da quantidade de PEUAPM adicionado. Análises de microscopia eletrônica de varredura (MEV), microscopia ótica e calorimetria diferencial de varredura (DSC) indicaram uma separação de fases nas blendas, mesmo quando o terceiro componente foi adicionado. Entretanto, as blendas que contém agente de acoplamento apresentaram diferenças na morfologia final, como observado através das análises de microscopia ótica durante a cristalização do sistema polimérico e nas análises de MEV nas amostras moldadas por injeção Para todas as blendas moldadas por injeção, a resistência ao impacto foi menor do que a encontrada para o PELMD puro. Por outro lado, nas amostras rotomoldadas não houve diferença significativa nas propriedades das blendas quando comparadas ao PELMD puro. As amostras extrusadas em rosca dupla, contendo óleo mineral ou cera e, posteriormente, moldadas por compressão apresentaram resistência ao impacto similares aos valores encontrados para o PELMD puro, sem significativas mudanças na processabilidade. Considerando as demais análises de propriedades mecânicas, não foi observada influência do terceiro componente.

Estudo das propriedades térmicas e mecânicas de blendas de PVDF/PANI

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Obtenção e caracterização de filmes de PHB e de blendas de PHB com borracha natural

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Foto e biodegradação de PEBD, PHB e suas blendas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Propriedades dielétricas e térmicas das blendas de poliestireno com ácido oléico e poliestireno com betacaroteno

As propriedades térmicas, dielétricas e ópticas de óleos vegetais vêm sendo estudadas pelo Grupo de Física de Materiais da Amazônia (GFMA) desde 1996 no Departamento de Física da UFPA. Recentemente uma interação com o laboratório de físico-química de polímeros do instituto de química da UnB possibilitou o estudo desses óleos e seus constituintes na forma de blendas poliméricas. Neste trabalho procuramos dar nossa contribuição a este estudo e investigamos propriedades térmicas e dielétricas das blendas de poliestireno (PS) com ácido oléico (AO) e betacaroteno (BC) em função da temperatura, foram realizadas medidas da constante dielétrica e da difusividade térmica utilizando-se capacitores planos de placas paralelas e a técnica fotopiroelétrica, respectivamente. Foi calculado o momento de dipolo associado à blenda PS/AO utilizando os modelos teóricos de Debye, Onsager e Kirkwood para ajuste linear dos dados experimentais. Os resultados encontrados mostram que a transição de fase do AO se mantêm e que ela encontra-se deslocado para temperaturas mais elevadas.

Estudo termoanalítico de blendas de poli(tereftalato de etileno) e poli(3-hidroxibutirato)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo morfológico da blenda polimérica poli(metacrilato de metila)/poli(tereftalato de etileno) reciclado (PMMA/PET)

Among the options for plastics modification more convenient, both from a technical-scientific and economic, is the development of polymer blends by processing in the molten state. This work was divide into two stages, with the aim to study the phase morphology of binary blend PMMA / PET blend and this compatibilized by the addition of the poly(methyl methacrylate-co-glycidyl methacrylate-co-ethyl acrylate) copolymer (MMA-GMA-EA). In the first stage is analyzed the morphology of the blend at a preliminary stage where we used the bottle-grade PET in a Haake torque rheometer and the effect of compatibilizer in this blend was evaluated. In the second stage the blend was processed using the recycled PET in a single screw extruder and subsequently injection molding in the shape of specimens for mechanical tests. In both stages we used a transmission electron microscopy (TEM) to observe the morphologies of the samples and an image analyzer to characterize them. In the second stage, as well as analysis by TEM, tensile test, scanning electron microscopy (SEM) and atomic force microscopy (AFM) was performed to correlate the morphology with the mechanical properties. The samples used in morphological analyzes were sliced by cryo-ultramicrotomy technique for the analysis by TEM and the analysis by SEM and AFM, we used the flat face of the block after cut cryogenic. It was found that the size of the dispersed phase decreased with the addition of MMA-GMA-EA in blends prepared in a Haake. In the tensile test, the values of maximum tensile strength and modulus of elasticity is maintained in a range between the value of pure PMMA the pure PET, while the elongation at break was influenced by the composition by weight of the PMMA mixture. The coupling agent corroborated the results presented in the blend PMMA / PETrec / MMA-GMA-EA (80/15/5 %w/w), obtained by TEM, AFM and SEM. It was concluded that the techniques used had a good morphologic correlation, and can be confirmed for final analysis of the morphological characteristics of the blends PMMA / PET

Influência de tratamentos térmicos no comportamento mecânico da blenda poli(metacrilato de metila) / poli(tereftalato de etileno) reciclado

Studies indicate that a variation in the degree of crystallinity of the components of a polymer blend influences the mechanical properties. This variation can be obtained by subjecting the blend to heat treatments that lead to changes in the spherulitic structure. The aim of this work is to analyze the influence of different heat treatments on the variation of the degree of crystallinity and to establish a relationship between this variation and the mechanical behavior of poly(methyl methacrylate)/poly(ethylene terephthalate) recycled (PMMA / PETrec) with and without the use of compatibilizer agent poly(methyl methacrylate-al-glycidyl methacrylate-al-ethyl acrylate) (MMAGMA- EA). All compositions were subjected to two heat treatments. T1 heat treatment the samples were treated at 130 ° C for 30 minutes and cooled in air. In T2, the samples were treated at 230 ° C for 5 minutes and cooled to approximately -10 ° C. The variation of the degree of crystallinity was determined by the proportional relationship between crystallinity and density, with the density measured by pycnometry. The mechanical behavior was verified by tensile tests with and without the presence of notches and pre-cracks, and by method of fracture toughness in plane strain (KIC). We used the scanning electron microscopy (SEM) to analyze the fracture surface of the samples. The compositions subjected to heat treatment T1, in general, showed an increase in the degree of crystallinity in tensile strength and a tendency to decrease in toughness, while compositions undergoing treatment T2 showed that the opposite behavior. Therefore, this work showed that heat treatment can give a polymer blend further diversity of its properties, this being caused by changes in the crystal structure

Micropartículas de poli (ácido láctico)/ poloxámero obtids por spray drying para liberação modificada de metotrexatro

New drug delivery systems have been used to increase chemotherapy efficacy due the possible drug resistance of cancer cells. Poly (lactic acid) (PLA) microparticles are able to reduce toxicity and prolong methotrexate (MTX) release. In addition, the use of PLA/poloxamer polymer blends can improve drug release due to changes in the interaction of particles with biological surfaces. The aim of this study was developing spray dried biodegradable MTX-loaded microparticles and evaluate PLA interactions with different kinds of Pluronic® (PLUF127 and PLUF68) in order to modulate drug release. The variables included different drug:polymer (1:10, 1:4.5, 1:3) and polymer:copolymer ratios (25:75, 50:50, 75:25). The precision and accuracy of spray drying method was confirmed assessing drug loading into particles (75.0- 101.3%). The MTX/PLA microparticles showed spherical shape with an apparently smooth surface, which was dependent on the PLU ratio used into blends particles. XRD and thermal analysis demonstrated that the drug was homogeneously dispersed into polymer matrix, whereas the miscibility among components was dependent on the used polymer:copolymer ratio. No new drug- polymer bond was identified by FTIR analysis. The in vitro performance of MTX-loaded PLA microparticles demonstrated an extended-release profile fitted using Korsmeyer- Peppas kinetic model. The PLU accelerated drug release rate possible due PLU leached in the matrix. Nevertheless, drug release studies carried out in cell culture demonstrated the ability of PLU modulating drug release from blend microparticles. This effect was confirmed by cytotoxicity observed according to the amount of drug released as a function of time. Thus, studied PLU was able to improve the performance of spray dried MTX-loaded PLA microparticles, which can be successfully used as carries for modulated drug delivery with potential in vivo application

Nanocompósitos com atividade antioxidante de amido de milho/isolado proteico de soro de leite/ óleo essencial de alecrim obtidos por extrusão termoplástica

In order to improve the quality and safety of food, the active packaging emerges as a new technology based on the release of composites beneficial to food products. Thus, biodegradable films incorporated with active substances have the function of acting as a barrier to external elements, protecting the product and increasing its shelf life. They are formulated from proteins, polysaccharides, lipids or from the combination of these compounds. However, there is a need to improve the performance properties of these packages. Nanotechnologies, then, emerges with the study of many nanoparticles as additives to modify the performance of biodegradable polymers. With this, we aimed at developing and active antioxidant film of corn starch blenders and whey protein isolate with rosemary essential oil or microcapsules of rosemary essential oil reinforced with sodium montmorillonite (MMTNa + ) nanoparticles by extrusion. The films were developed and characterized in a first stage for the selection of the best polymeric blender using the following analyses: water vapor permeability (WVP), machanical properties; optical, thermogravimetry (TG), differential scanning calorimetry (DSC), x-ray diffraction (XRD) and scanning electron microscopy (SEM). In the second stage, montmorillonite clay nanoparticles and rosemary essential oil were added as reinforcement to evaluate its antioxidant effect. In a third stage, we studied the addition of microcapsules of rosemary essential oil (MR) as a form of protecting the active agent and its antioxidant potential in the films. The results indicate that the development of p olymeric blender with 30% of corn starch substitution is the most indicated for future work. The addition of rosemary essential oil or microcapsule of rosemary essential oil allowed for the obtaining of nanocomposites with antioxidant potential for application in food packages.

Estudo morfológico da blenda polimérica poli(metacrilato de metila)/poli(tereftalato de etileno) reciclado (PMMA/PET)

Among the options for plastics modification more convenient, both from a technical-scientific and economic, is the development of polymer blends by processing in the molten state. This work was divide into two stages, with the aim to study the phase morphology of binary blend PMMA / PET blend and this compatibilized by the addition of the poly(methyl methacrylate-co-glycidyl methacrylate-co-ethyl acrylate) copolymer (MMA-GMA-EA). In the first stage is analyzed the morphology of the blend at a preliminary stage where we used the bottle-grade PET in a Haake torque rheometer and the effect of compatibilizer in this blend was evaluated. In the second stage the blend was processed using the recycled PET in a single screw extruder and subsequently injection molding in the shape of specimens for mechanical tests. In both stages we used a transmission electron microscopy (TEM) to observe the morphologies of the samples and an image analyzer to characterize them. In the second stage, as well as analysis by TEM, tensile test, scanning electron microscopy (SEM) and atomic force microscopy (AFM) was performed to correlate the morphology with the mechanical properties. The samples used in morphological analyzes were sliced by cryo-ultramicrotomy technique for the analysis by TEM and the analysis by SEM and AFM, we used the flat face of the block after cut cryogenic. It was found that the size of the dispersed phase decreased with the addition of MMA-GMA-EA in blends prepared in a Haake. In the tensile test, the values of maximum tensile strength and modulus of elasticity is maintained in a range between the value of pure PMMA the pure PET, while the elongation at break was influenced by the composition by weight of the PMMA mixture. The coupling agent corroborated the results presented in the blend PMMA / PETrec / MMA-GMA-EA (80/15/5 %w/w), obtained by TEM, AFM and SEM. It was concluded that the techniques used had a good morphologic correlation, and can be confirmed for final analysis of the morphological characteristics of the blends PMMA / PET

Influência de tratamentos térmicos no comportamento mecânico da blenda poli(metacrilato de metila) / poli(tereftalato de etileno) reciclado

Studies indicate that a variation in the degree of crystallinity of the components of a polymer blend influences the mechanical properties. This variation can be obtained by subjecting the blend to heat treatments that lead to changes in the spherulitic structure. The aim of this work is to analyze the influence of different heat treatments on the variation of the degree of crystallinity and to establish a relationship between this variation and the mechanical behavior of poly(methyl methacrylate)/poly(ethylene terephthalate) recycled (PMMA / PETrec) with and without the use of compatibilizer agent poly(methyl methacrylate-al-glycidyl methacrylate-al-ethyl acrylate) (MMAGMA- EA). All compositions were subjected to two heat treatments. T1 heat treatment the samples were treated at 130 ° C for 30 minutes and cooled in air. In T2, the samples were treated at 230 ° C for 5 minutes and cooled to approximately -10 ° C. The variation of the degree of crystallinity was determined by the proportional relationship between crystallinity and density, with the density measured by pycnometry. The mechanical behavior was verified by tensile tests with and without the presence of notches and pre-cracks, and by method of fracture toughness in plane strain (KIC). We used the scanning electron microscopy (SEM) to analyze the fracture surface of the samples. The compositions subjected to heat treatment T1, in general, showed an increase in the degree of crystallinity in tensile strength and a tendency to decrease in toughness, while compositions undergoing treatment T2 showed that the opposite behavior. Therefore, this work showed that heat treatment can give a polymer blend further diversity of its properties, this being caused by changes in the crystal structure