On the Bauschinger effect in dual phase steel at high levels of strain

The effect of volume fraction and hardness of martensite on the Bauschinger effect in Dual Phase (DP) steel was investigated for strain levels close to those observed in automotive stamping. Five different grades of DP steel were produced by controlled heat treatment allowing the examination of the Bauschinger effect for three different volume fractions of martensite and three levels of martensite hardness. Compression-tension and shear reversal tests were performed to examine the Bauschinger effect at high levels of forming strain. Good correlation between the shear reversal and the compression-tension test was observed suggesting that for DP steel, shear stress strain data, converted to equivalent stress-strain, may be applied directly to characterize kinematic hardening behavior for numerical simulations. Permanent softening was observed following strain reversal and increased with martensite volume fraction and pre-strain level. While the Bauschinger ratio saturates at 3% pre-strain, the Bauschinger strain increases linearly with forming strain without showing saturation. This suggests that to model material behavior accurately in forming processes involving complex loading paths and high levels of strain, test data generated at high strain is required.

Effect of Microstructural Interfaces on the Mechanical Response of Crystalline Metallic Materials

Advances in nano-scale mechanical testing have brought about progress in the understanding of physical phenomena in materials and a measure of control in the fabrication of novel materials. In contrast to bulk materials that display size-invariant mechanical properties, sub-micron metallic samples show a critical dependence on sample size. The strength of nano-scale single crystalline metals is well-described by a power-law function, σαD^-n, where D is a critical sample size and n is a experimentally-fit positive exponent. This relationship is attributed to source-driven plasticity and demonstrates a strengthening as the decreasing sample size begins to limit the size and number of dislocation sources. A full understanding of this size-dependence is complicated by the presence of microstructural features such as interfaces that can compete with the dominant dislocation-based deformation mechanisms. In this thesis, the effects of microstructural features such as grain boundaries and anisotropic crystallinity on nano-scale metals are investigated through uniaxial compression testing. We find that nano-sized Cu covered by a hard coating displays a Bauschinger effect and the emergence of this behavior can be explained through a simple dislocation-based analytic model. Al nano-pillars containing a single vertically-oriented coincident site lattice grain boundary are found to show similar deformation to single-crystalline nano-pillars with slip traces passing through the grain boundary. With increasing tilt angle of the grain boundary from the pillar axis, we observe a transition from dislocation-dominated deformation to grain boundary sliding. Crystallites are observed to shear along the grain boundary and molecular dynamics simulations reveal a mechanism of atomic migration that accommodates boundary sliding. We conclude with an analysis of the effects of inherent crystal anisotropy and alloying on the mechanical behavior of the Mg alloy, AZ31. Through comparison to pure Mg, we show that the size effect dominates the strength of samples below 10 μm, that differences in the size effect between hexagonal slip systems is due to the inherent crystal anisotropy, suggesting that the fundamental mechanism of the size effect in these slip systems is the same.

On the definition of an kinematic hardening effect graph for sheet metal forming process simulations

The objective of this work is to develop a kinematic hardening effect graph (KHEG) which can be used to evaluate the effect of kinematic hardening on the model accuracy of numerical sheet metal forming simulations and this without the need of complex material characterisation. The virtual manufacturing process design and optimisation depends on the accuracy of the constitutive models used to represent material behaviour. Under reverse strain paths the Bauschinger effect phenomenon is modelled using kinematic hardening models. However, due to the complexity of the experimental testing required to characterise this phenomenon in this work the KHEG is presented as an indicator to evaluate the potential benefit of carrying out these tests. The tool is validated with the classic three point bending process and the U-channel width drawbead process. In the same way, the capability of the KHEG to identify effects in forming processes that do not include forming strain reversals is identified.

Estudo do efeito Bauschinger em tubos de aço API 5l x70 aplicados no transporte de petróleo e gás

Despite the growing concern in seeking more sustainable energy sources, oil demand is likely to grow in coming years. To keep up with this growth, the oil industry has increasingly invested in innovation and efficiency. Knowing that, new technologies have been developed to explore deeper waters, without giving up the best practices in worldwide operational safety. The use of rigid pipelines in deepwater offshore facilities is increasing quickly and because of this, the ways of storing and launching pipe have been studied and perfected. In this paper the Bauschinger effect on API 5L X70 steel was analyzed proving that there was a reduction in yield strength when an effort was applied in a previous direction, then an effort was then applied in the opposite direction. To observe this phenomenon, the tensile test was conducted to determine the mechanical properties of the base metal, such as yield stress, tensile strength, elasticity and maximum tensile, so then compare it with the results obtained in the Bauschinger Effect Test. The analysis results showed that the steel had high resistance, with good plastic deformation capacity without failing, well-defined yield point, showing itself appropriate for the operation of oil and gas pipes

Estudo do efeito Bauschinger em tubos de aço API 5l x70 aplicados no transporte de petróleo e gás

Despite the growing concern in seeking more sustainable energy sources, oil demand is likely to grow in coming years. To keep up with this growth, the oil industry has increasingly invested in innovation and efficiency. Knowing that, new technologies have been developed to explore deeper waters, without giving up the best practices in worldwide operational safety. The use of rigid pipelines in deepwater offshore facilities is increasing quickly and because of this, the ways of storing and launching pipe have been studied and perfected. In this paper the Bauschinger effect on API 5L X70 steel was analyzed proving that there was a reduction in yield strength when an effort was applied in a previous direction, then an effort was then applied in the opposite direction. To observe this phenomenon, the tensile test was conducted to determine the mechanical properties of the base metal, such as yield stress, tensile strength, elasticity and maximum tensile, so then compare it with the results obtained in the Bauschinger Effect Test. The analysis results showed that the steel had high resistance, with good plastic deformation capacity without failing, well-defined yield point, showing itself appropriate for the operation of oil and gas pipes

A meso elastoplastic constitutive model for polycrystalline metals based on equivalent slip systems with latent hardening

A meso material model for polycrystalline metals is proposed, in which the tiny slip systems distributing randomly between crystal slices in micro-grains or on grain boundaries are replaced by macro equivalent slip systems determined by the work-conjugate principle. The elastoplastic constitutive equation of this model is formulated for the active hardening, latent hardening and Bauschinger effect to predict macro elastoplastic stress-strain responses of polycrystalline metals under complex loading conditions. The influence of the material property parameters on size and shape of the subsequent yield surfaces is numerically investigated to demonstrate the fundamental features of the proposed material model. The derived constitutive equation is proved accurate and efficient in numerical analysis. Compared with the self-consistent theories with crystal grains as their basic components, the present theory is much simpler in mathematical treatment.

Tensile response of passivated films with climb-assisted dislocation glide

The tensile response of single crystal films passivated on two sides is analysed using climb enabled discrete dislocation plasticity. Plastic deformation is modelled through the motion of edge dislocations in an elastic solid with a lattice resistance to dislocation motion, dislocation nucleation, dislocation interaction with obstacles and dislocation annihilation incorporated through a set of constitutive rules. The dislocation motion in the films is by glide-only or by climb-assisted glide whereas in the surface passivation layers dislocation motion occurs by glide-only and penalized by a friction stress. For realistic values of the friction stress, the size dependence of the flow strength of the oxidised films was mainly a geometrical effect resulting from the fact that the ratio of the oxide layer thickness to film thickness increases with decreasing film thickness. However, if the passivation layer was modelled as impenetrable, i.e. an infinite friction stress, the plastic hardening rate of the films increases with decreasing film thickness even for geometrically self-similar specimens. This size dependence is an intrinsic material size effect that occurs because the dislocation pile-up lengths become on the order of the film thickness. Counter-intuitively, the films have a higher flow strength when dislocation motion is driven by climb-assisted glide compared to the case when dislocation motion is glide-only. This occurs because dislocation climb breaks up the dislocation pile-ups that aid dislocations to penetrate the passivation layers. The results also show that the Bauschinger effect in passivated thin films is stronger when dislocation motion is climb-assisted compared to films wherein dislocation motion is by glide-only. © 2012 Elsevier Ltd.

A non-associated plasticity model with anisotropic and nonlinear kinematic hardening for simulation of sheet metal forming

A material model for more thorough analysis of plastic deformation of sheet materials is presented in this paper. This model considers the following aspects of plastic deformation behavior of sheet materials: (1) the anisotropy in yield stresses and in work hardening by using Hill's 1948 quadratic yield function and non-constant stress ratios which leads to different flow stress hardening in different directions, (2) the anisotropy in plastic strains by using a quadratic plastic potential function and non-associated flow rule, also based on Hill's 1948 model and r-values, and (3) the cyclic hardening phenomena such as the Bauschinger effect, permanent softening and transient behavior for reverse loading by using a coupled nonlinear kinematic hardening model. Plasticity fundamentals of the model were derived in a general framework and the model calibration procedure was presented for the plasticity formulations. Also, a generic numerical stress integration procedure was developed based on backward-Euler method, so-called multi-stage return mapping algorithm. The model was implemented in the framework of the finite element method to evaluate the simulation results of sheet metal forming processes. Different aspects of the model were verified for two sheet metals, namely DP600 steel and AA6022 aluminum alloy. Results show that the new model is able to accurately predict the sheet material behavior for both anisotropic hardening and cyclic hardening conditions. The drawing of channel sections and the subsequent springback were also simulated with this model for different drawbead configurations. Simulation results show that the current non-associated anisotropic hardening model is able to accurately predict the sidewall curl in the drawn channel sections.

Constitutive modelling of high strength titanium alloy Ti-6Al-4 V for sheet forming applications at room temperature

To enable the design and optimisation of forming processes at room temperature the material behaviour of Ti-6Al-4 V needs to be accurately represented in numerical analysis and this requires an advanced material model. In particular, an accurate representation of the shape and size of the yield locus as well as its evolution during forming is important. In this study a rigorous set of experiments on the quasi-static deformation behaviour of a Ti-6Al-4 V alloy sheet sample at room temperature was conducted for various loading conditions and a constitutive material model developed. To quantify the anisotropy and asymmetry properties, tensile and compression tests were carried out for different specimen orientations. To examine the Bauschinger effect and the transient hardening behaviour in - plane tensile - compression and compression - tensile tests were performed. Balanced biaxial and plane strain tension tests were conducted to construct and validate the yield surface of the Ti-6Al-4 V alloy sheet sample at room temperature. A recently proposed anisotropic elastic-plastic constitutive material model, so-called HAH, was employed to describe the behaviour, in particular for load reversals. The HAH yield surface is composed of a stable component, which includes plastic anisotropy and is distorted by a fluctuating component. The key of the formulation is the use of a suitable yield function that reproduces the experimental observations well for the stable component. Meanwhile, the rapid evolution of the material structure must be captured at the macro - scale level by the fluctuating component embedded in the HAH model. Compared to conventional hardening equations, the proposed model leads to higher accuracy in predicting the Bauschinger effect and the transient hardening behaviour for the Ti-6Al-4 V sheet sample tested at room temperature.