Manipulation of the Hydration Levels in Minerals of Sodium Cadmium Bisulfate toward the Design of Functional Materials

Several variants of hydrated sodium cadmium bisulfate, Na(2)Cd(2)(SO(4))(3) center dot 3H(2)O, Na(2)Cd(SO(4))(2) center dot 2H(2)O, and Na(2)Cd(SO(4))(2) center dot 4H(2)O have been synthesized, and their thermal properties followed by phase transitions have been invesigated. The formation of these phases depends on the stochiometry and the time taken for crystallization from water. Na(2)Cd(2)(SO(4))(3)center dot 3H(2)O, which crystallizes in the trigonal system, space group P3c, is grown from the aqueous solution in about four weeks. The krohnkite type mineral Na(2)Cd(SO(4))(2) center dot 2H(2)O and the mineral astrakhanite, also known as blodite, Na(2)Cd (SO(4))(2)center dot 4H(2)O, crystallize concomittantly in about 24 weeks. Both these minerals belong to the monoclinic system(space group P2(1)/c). Na(2)Cd(2)(SO(4))(3)center dot 3H(2)O loses water completely when heated to 250 degrees C and transforms to a dehydrated phase (cubic system, space group I (4) over bar 3d) whose structure has been established using ab initio powder diffration techniques. Na(2)Cd(SO(4))(2)center dot 2H(2)O transforms to alpha-Na(2)Cd(SO(4))(2) (space group C2/c) on heating to 150 degrees C which is a known high ionic conductor and remains intact over prolonged periods of exposure to moisture (over six months). However, when alpha-Na(2)Cd(SO(4))(2) is heated to 570 degrees C followed by sudden quenching in liquid nitrogen beta-Na(2)Cd(SO(4))(2) (P2(1)/c) is formed. beta-Na(2)Cd(SO(4))(2) takes up water from the atmosphere and gets converted completely to the krohnkite type mineral in about four weeks. Further, beta-Na(2)Cd(SO(4))(2) has a conductivity behavior comparable to the a-form up to 280 degrees C, the temperature required for the transformation of the beta- to alpha-form. These experiments demonstrate the possibility of utilizing the abundantly available mineral sources as precursors to design materials with special properties.

Hydration of the Bisulfate Ion: Atmospheric Implications

Using molecular dynamics configurational sampling combined with ab initio energy calculations, we determined the low energy isomers of the bisulfate hydrates. We calculated the CCSD(T) complete basis set (CBS) binding electronic and Gibbs free energies for 53 low energy isomers of HSO4–(H2O)n=1–6 and derived the thermodynamics of adding waters sequentially to the bisulfate ion and its hydrates. Comparing the HSO4–/H2O system to the neutral H2SO4/H2O cluster, water binds more strongly to the anion than it does to the neutral molecules. The difference in the binding thermodynamics of HSO4–/H2O and H2SO4/H2O systems decreases with increasing number of waters. The thermodynamics for the formation of HSO4–(H2O)n=1–5 is favorable at 298.15 K, and that of HSO4–(H2O)n=1–6 is favorable for T < 273.15 K. The HSO4– ion is almost always hydrated at temperatures and relative humidity values encountered in the troposphere. Because the bisulfate ion binds more strongly to sulfuric acid than it does to water, it is expected to play a role in ion-induced nucleation by forming a strong complex with sulfuric acid and water, thus facilitating the formation of a critical nucleus.

Diaryl dihydropyrazole-3-carboxamides with significant in vivo antiobesity activity related to CB1 receptor antagonism: Synthesis, biological evaluation, and molecular modeling in the homology model

A number of analogues of diaryl dihydropyrazole-3-carboxamides have been synthesized. Their activities were evaluated for appetite suppression and body weight reduction in animal models. Depending on the chemical modification of the selected dihydropyrazole scaffold, the lead compoundsthe bisulfate salt of (±)-5-(4-chlorophenyl)-1-(2,4-dichlorophenyl)-4,5-dihydro-1H-pyrazole-3-carboxylic acid morpholin-4-ylamide 26 and the bisulfate salt of (−)-5-(4-chlorophenyl)-1-(2,4-dichlorophenyl)-4,5-dihydro-1H-pyrazole-3-carboxylic acid morpholin-4-ylamide 30showed significant body weight reduction in vivo, which is attributed to their CB1 antagonistic activity and exhibited a favorable pharmacokinetic profile. The molecular modeling studies also showed interactions of two isomers of (±)-5-(4-chlorophenyl)-1-(2,4-dichlorophenyl)-4,5-dihydro-1H-pyrazole-3-carboxylic acid morpholin-4-ylamide 9 with CB1 receptor in the homology model similar to those of N-piperidino-5-(4-chlorophenyl)-1-(2,4-dichlorophenyl)-4-methyl-3-pyrazole-carboxamide (rimonabant) 1 and 4S-(−)-3-(4-chlorophenyl)-N-methyl-N‘-[(4-chlorophenyl)-sulfonyl]-4-phenyl-4,5-dihydro-1H-pyrazole-1-carboxamidine (SLV-319) 2.

Kinetic study of formic acid oxidation on carbon supported Pd electrocatalyst

The oxidation of formic acid at the Pd/C catalyst electrode is a completely irreversible kinetic process with the reaction order of 1.0. The oxidation rate of formic acid is increased with increasing the concentration of formic acid and is decreased with increasing H+ concentration. The apparent negative reaction order with respect to H+ is about -0.18 or -0.04 in H2SO4 or HClO4 solution respectively, because bisulfate anions would inhibit formic acid oxidation at some extent. The kinetic parameters, charge transfer coefficient and the diffusion coefficient of formic acid were obtained under the quasi steady-state conditions.

Research on various factors influencing the moisture absorption property of sodium polyacrylate

Sodium polyacrylate was synthesized with acrylic acid as the monomer, and sodium bisulfate and ammonium persulfate as the initiator, by means of aqueous solution polymerization. The factors influencing the properties of moisture absorption, such as monomer concentration, dosage of initiator, and reaction temperature were systematically investigated. The experimental results indicate that the moisture-absorbing property of this polymer was better than other traditional material, such as silica gel, and molecular sieve. The best reaction condition and formula are based on the orthogonal experiment design. The optimum moisture absorbency of sodium polyacrylate reaches 1.01 g/g. The mathematical correlation of this polymer with various factors and moisture absorbency is obtained based on the multiple regression analysis. The moisture content intuitive analysis table shows that neutralization degree has the most significant influence on moisture absorbency, followed by monomer concentration and reaction temperature, while other factors have less influence.

The effects of the specific adsorption of anion on the reactivity of the Ru(0001) surface towards CO adsorption and oxidation: in situ FTIRS studies

The dynamics of adsorption and oxidation of CO on Ru(0001) electrode in sulfuric acid solution have been studied using in situ FTIR spectroscopy under potential control and at open circuit, the latter at 20 and 55 degrees C. The in situ IR data show clearly that the bisulfate anion adsorbs on the Ru(0001) surface over the potential range from -200 mV to 350 mV (vs. Ag/AgCl) at 20 degrees C in the absence and presence of adsorbed CO; however, increasing the temperature to 55 degrees C and/ or increasing the concentration of dissolved O-2 reduces the bisulfate adsorption. The formation of surface (hydro-) oxide at higher potentials replaces the bisulfate adsorbates. Both linear (COL) and three-fold hollow bonded CO (COH) adsorbates were produced following CO adsorption at Ru(0001) in H2SO4, as was observed in our previous studies in HClO4. However, the amount of adsorbed CO observed in H2SO4 was ca. 10% less than that in HClO4; in addition, the COL and COH frequencies were higher in H2SO4, and the onset potential for COads oxidation 25 mV lower. These new results are interpreted in terms of a model in which the adsorbed bisulfate weakens the CO adlayer, allowing the active Ru oxide layer to form at lower potentials. Significantly different results were observed at open circuit in H2SO4 compared both to the data under potential control and to our earlier data in HClO4, and these observations were rationalized in terms of the adsorbed HSO4- anions (pre-adsorbed at -200 mV) inhibiting the oxidation of the surface at open circuit (after stepping from the initial potential of -200 mV), as the latter was no longer driven by the imposed electrochemical potential but via chemical oxidation by trace dissolved O-2. Results from experiments at open circuit at 55 degrees C and using oxygen-saturated H2SO4 supported this model. The difference in Ru surface chemistry between imposed electrochemical control and chemical control has potential implications with respect to fuel cell electrocatalysis.

In situ FTIR spectroscopic studies of the oxidation of CO adsorbates on Ru(0 0 0 1) electrodes under open circuit conditions

This paper reports the first observation, using in situ FTIR spectroscopy, of the oxidation of CO adsorbates on the Ru(0001) electrode to CO under open circuit (oc) conditions in both perchloric acid and sulphuric acid solution at 20 and 55 °C. While the significant oc oxidation of the adsorbed CO on the Ru(0001) electrode was observed in perchloric acid solution, much less oc oxidation took place in sulfuric acid solution due to the specific adsorption of bisulfate at the Ru surface which inhibits the surface oxidation and reduces the reactivity of the surface towards the oxidation of CO . The oc oxidation of the CO depends strongly on the oxygen concentration in the solution and the temperature. The data so obtained are compared to those observed at the gas|solid interface, as well as to those obtained from the electro-oxidation of CO , and possible new catalytic oxidation reaction mechanisms are discussed. In addition, it is shown that the C-O frequency of the adsorbed CO may be used as an effective probe of the open circuit potential. © 2003 Elsevier B.V. All rights reserved.

High Viscosity of Imidazolium Ionic Liquids with the Hydrogen Sulfate Anion: A Raman Spectroscopy Study

Ionic liquids based on 1-alkyl-3-methylimidazolium cations and the hydrogen sulfate (or bisulfate) anion, HSO4-, are much more viscous than ionic liquids with alkyl sulfates, RSO4-. The structural origin of the high viscosity of HSO4- ionic liquids is unraveled from detailed comparison of the anion Raman bands in 1-ethyl-3-methylimidazolium hydrogen sulfate and 1-butyl-3-methylimidazolium hydrogen sulfate with available data for simple HSO(4)(-) salts in crystalline phase, molten phase, and aqueous solution. Two Raman bands at 1046 and 1010 cm(-1) have been assigned as symmetric stretching modes nu(s)(S = O) of HSO4-, the latter being characteristic of chains of hydrogen-bonded anions. The intensity of this component increases in the supercooled liquid phase. For comparison purposes, Raman spectra of 1-ethyl-3-methylimidazolium ethyl sulfate and 1-butyl-3-methylimidazolium methyl sulfate have been also obtained. There is no indication of difference in the strength of hydrogen bond interactions of imidazolium cations with HSO4- or RSO4- anions. Raman spectra at high pressures, up to 2.6 GPa, are also discussed. Raman spectroscopy provides evidence that hydrogen-bonded anions resulting in anion-anion interaction is the reason for the high viscosity of imidazolium ionic liquids with HSO4-. If the ionic liquid is exposed to moisture, these structures are disrupted upon absorption of water from the atmosphere.

Einsatz eines Aerosolmassenspektrometers während der CYPHEX-Kampagne und zur Methodenentwicklung einer Echtzeitquantifizierung gasförmiger Amine

Atmosphärische Aerosole haben einen starken Einfluss auf das Klima, der bisher nur grundlegend verstanden ist und weiterer Forschung bedarf. Das atmosphärische Verhalten der Aerosolpartikel hängt maßgeblich von ihrer Größe und chemischen Zusammensetzung ab. Durch Reflexion, Absorption und Streuung des Sonnenlichtes verändern sie den Strahlungshaushalt der Erde direkt und durch ihre Einflussnahme auf die Wolkenbildung indirekt. Besonders gealterte, stark oxidierte organische Aerosole mit großem Sauerstoff-zu-Kohlenstoff-Verhältnis wirken als effektive Wolkenkondensationskeime. Neben primären Aerosolpartikeln, die direkt partikelförmig in die Atmosphäre gelangen, spielen sekundäre Aerosolpartikel eine große Rolle, die aus Vorläufergasen in der Atmosphäre entstehen. Aktuelle Forschungsergebnisse legen nahe, dass kurzkettige aliphatische Amine bei Nukleationsprozessen beteiligt sind und somit die Partikelneubildung vielerorts mitsteuern. Um die Rolle von Aminen in der Atmosphäre besser erforschen und industrielle Emissionen kontrollieren zu können, bedarf es einer zuverlässigen Methode zur Echtzeitquantifizierung gasförmiger Amine mit hoher Zeitauflösung und niedriger Nachweisgrenze.rnDas hochauflösende Flugzeit-Aerosolmassenspektrometer (HR-ToF-AMS) bietet die Möglichkeit, atmosphärische Partikel in Echtzeit zu analysieren. Dabei werden Größe, Menge und grundlegende chemische Zusammensetzung erfasst. Anorganische Aerosolbestandteile können eindeutig zugeordnet werden. Es ist jedoch kaum möglich, einzelne organische Verbindungen in den komplizierten Massenspektren atmosphärischer Aerosole zu identifizieren und quantifizieren.rnIn dieser Arbeit wird atmosphärisches Aerosol untersucht, das im Westen Zyperns während der CYPHEX-Kampagne mit einem HR-ToF-AMS gemessen wurde. An diesem Standort ist vor allem stark gealtertes Aerosol vorzufinden, das aus Zentral- und Westeuropa stammt. Lokale Einflüsse spielen fast keine Rolle. Es wurde eine durchschnittliche Massenkonzentration von 10,98 μg/m3 gefunden, zusammengesetzt aus 57 % Sulfat, 30 % organischen Bestandteilen, 12 % Ammonium, < 1 % Nitrat und < 1 % Chlorid, bezogen auf das Gewicht. Der Median des vakuum-aerodynamischen Durchmessers betrug 446,25 nm. Es wurde sehr acides Aerosol gefunden, dessen anorganische Bestandteile weitgehend der Zusammensetzung von Ammoniumhydrogensulfat entsprachen. Tag-Nacht-Schwankungen in der Zusammensetzung wurden beobachtet. Die Sulfatkonzentration und die Acidität zeigten tagsüber Maxima und nachts Minima. Konzentrationsschwankungen an Nitrat und Chlorid zeigten einen weniger ausgeprägten Rhythmus, Maxima fallen aber immer mit Minima der Sulfatkonzentration, Aerosolacidität und Umgebungstemperatur zusammen. Organische Aerosolbestandteile entsprachen stark gealtertem, schwerflüchtigem oxidiertem organischem Aerosol. Es wurde eine interne Mischung der Partikel beobachtet, die ebenfalls meist bei alten Aerosolen auftritt.rnUm mit dem HR-ToF-AMS auch einzelne organische Verbindungen identifizieren und quantifizieren zu können, wurde eine Methode entwickelt, mit der man Amine der Gasphase selektiv in künstlich erzeugte Phosphorsäurepartikel aufnimmt und so für die HR-ToF-AMS-Messung zugänglich macht. Dadurch kombiniert man die Vorteile der Online-Messung des HR-ToF-AMS mit den Vorteilen klassischer Offline-Probenahmen. So können in Echtzeit sehr einfache Massenspektren gemessen werden, in denen störende Komponenten abgetrennt sind, während die Analyten eindeutig identifiziert werden können. Systeme dieser Art wurden GTRAP-AMS (Gaseous compound TRapping in Artificially-generated Particles – Aerosol Mass Spectrometry) genannt. Kalibrierungen für (Mono)Methylamin, Dimethylamin, Trimethylamin, Diethylamin und Triethylamin ergaben Nachweisgrenzen im ppt-Bereich bei einer Zeitauflösung von 3 min. Kammerexperimente zur Aminemission von Pflanzen zeigten eine gute Übereinstimmung des neu entwickelten Systems mit einer Gasdiffusionsabscheider-Offline-Probenahme und anschließender ionenchromatographischer Analyse. Beide Methoden zeigten Reaktionen der Pflanzen auf eine Veränderung der Lichtverhältnisse, während erhöhte Ozonkonzentrationen die Aminemission nicht veränderten. Die GTRAP-AMS-Methode eignet sich bereits für die Messung von Umgebungsluftkonzentrationen an einigen Orten, für die meisten Orte reicht die Nachweisgrenze allerdings noch nicht aus. Die Technik könnte bereits zur Echtzeitkontrolle industrieller Abgasemissionen eingesetzt werden.

Computational Study of the Hydration of Sulfuric Acid Dimers: Implications for Acid Dissociation and Aerosol Formation

We have investigated the thermodynamics of sulfuric acid dimer hydration using ab initio quantum mechanical methods. For (H2SO4)2(H2O)n where n = 0−6, we employed high-level ab initio calculations to locate the most stable minima for each cluster size. The results presented herein yield a detailed understanding of the first deprotonation of sulfuric acid as a function of temperature for a system consisting of two sulfuric acid molecules and up to six waters. At 0 K, a cluster of two sulfuric acid molecules and one water remains undissociated. Addition of a second water begins the deprotonation of the first sulfuric acid leading to the di-ionic species (the bisulfate anion HSO4−, the hydronium cation H3O+, an undissociated sulfuric acid molecule, and a water). Upon the addition of a third water molecule, the second sulfuric acid molecule begins to dissociate. For the (H2SO4)2(H2O)3 cluster, the di-ionic cluster is a few kcal mol−1 more stable than the neutral cluster, which is just slightly more stable than the tetra-ionic cluster (two bisulfate anions, two hydronium cations, and one water). With four water molecules, the tetra-ionic cluster, (HSO4−)2(H3O+)2(H2O)2, becomes as favorable as the di-ionic cluster H2SO4(HSO4−)(H3O+)(H2O)3 at 0 K. Increasing the temperature favors the undissociated clusters, and at room temperature we predict that the di-ionic species is slightly more favorable than the neutral cluster once three waters have been added to the cluster. The tetra-ionic species competes with the di-ionic species once five waters have been added to the cluster. The thermodynamics of stepwise hydration of sulfuric acid dimer is similar to that of the monomer; it is favorable up to n = 4−5 at 298 K. A much more thermodynamically favorable pathway forming sulfuric acid dimer hydrates is through the combination of sulfuric acid monomer hydrates, but the low concentration of sulfuric acid relative to water vapor at ambient conditions limits that process.