Micropillar and macropillar compression responses of magnesium single crystals oriented for single slip or extension twinning

Uniaxial compression experiments were conducted on two magnesium (Mg) single crystals whose crystallographic orientations facilitate the deformation either by basal slip or by extension twinning. Specimen size effects were examined by conducting experiments on mu m- and mm-sized samples. A marked specimen size effect was noticed, with micropillars exhibiting significantly higher flow stress than bulk samples. Further, it is observed that the twin nucleation stress exerts strong size dependence, with micropillars requiring substantially higher stress than the bulk samples. The flow curves obtained on the bulk samples are smooth whereas those obtained from micropillars exhibit intermittent and precipitous stress drops. Electron backscattered diffraction and microstructural analyses of the deformed samples reveal that the plastic deformation in basal slip oriented crystals occurs only by slip while twin oriented crystals deform by both slip and twinning modes. The twin oriented crystals exhibit a higher strain hardening during plastic deformation when compared to the single slip oriented crystals. The strain hardening rate, theta, of twin oriented crystals is considerably greater in micropillars compared to the bulk single crystals, suggesting the prevalence of different work hardening mechanisms at these different sample sizes. (C) 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Slip during tension testing of Mg-3A1-1Zn sheet

The activation of slip and twinning deformation modes in Mg-3Al-1Zn alloy was investigated by means of both in-situ and ex-situ methods at ambient temperature using electron back scattering diffraction (EBSD). The results confirm the importance of non-basal slip and c-axis compression double twinning. During tensile deformation of rolled sheet, 63% of the observed slip traces were ascribed to prismatic slip, 33% to basal slip and 4% to <c+a> slip. Prismatic slip was frequently observed in grain interiors. The density of twinning was quantified in samples tested along transverse, extrusion and rolling directions at failure. The values in the range of 0.02-0.18 twins per square micron were found depending on sample orientation. The results show the effect of twinning on failure.

Time and spatial resolution of slip and twinning in a grain embedded within a magnesium polycrystal

Plastic yielding in magnesium alloys frequently involves the initiation of both slip and twinning events. A proper understanding of the phenomenon at the grain level requires knowledge of how these two mechanisms progress and interact over both time and space and what the local resolved stresses are. To date, simultaneous collection of such information has not been achievable. To address this shortfall, we have developed a modified Laue based in situ micro X-ray diffraction technique with an unprecedented combination of time and spatial resolution. A ten-fold reduction in data collection times is realized by the refinement of rapid polychromatic Laue "single-shot" mapping. From single Laue patterns, we extract grain depth information, detect onset of yielding and achieve 2 × 10-4 lattice strain resolution. The technique is employed to examine yielding and twinning in a magnesium grain embedded ∼200 μm below the sample surface. We examine 13 time steps and reveal the following behaviour: initial onset of basal slip, subsequent onset of twinning, development of further accommodation slip and evolution of twin shape and size; along with the corresponding values of local resolved shear stresses. © 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Distinguishing between slip and twinning events during nanoindentation of magnesium alloy AZ31

Nanoindentation was performed in selected grain orientations close to [. 112-0] and [. 101-0] in magnesium alloy Mg-3Al-1Zn. The atomic force microscopy (AFM) and electron backscatter diffraction (EBSD) were used to examine the nanoindentation imprint. Two critical events, yielding and pop-in were observed in the depth-load curves. Slip trace analysis suggests that basal slip is responsible for yielding. The following pop-in events at higher loads are associated with the appearance {. 101-2} twins on the surface. The critical resolved shear stress (CRSS) was estimated to be in the range of 220-400. MPa for the initiation of basal slip.

Investigation of precipitate hardening of slip and twinning in Mg5%Zn by micropillar compression

A Mg-5%Zn alloy has been aged to form c-axis rod precipitates which are known to increase strength. Micropillar compression tests were carried out in the precipitate-free and aged samples to investigate the effects of these precipitates on twinning and slip in magnesium alloys. Basal slip, pyramidal slip and {101¯2} twinning were selectively activated by compressing micropillars in the [112¯3], [0 0 0 1] and [112¯0] orientations, respectively. It has been found that precipitation causes moderate hardening of the basal slip system, and also significantly increases the work hardening rate. The compression of [112¯0] initiated twinning, but the present experiments were dominated by twin nucleation, rather than growth. It was found that the effect of precipitation on twin nucleation was negligible. Precipitation had little effect on specimens compressed in the c-axis.

In-situ X-ray diffraction studies of slip and twinning in the presence of precipitates in AZ91 alloy

The effect of basal plate precipitates on the hardening of basal slip and {101¯2} twinning modes was investigated for a non-aged and aged AZ91 alloy in the twin dominated strain paths. Exploiting in-situ synchrotron and laboratory based X-ray diffraction methodologies, we quantified the critical resolved shear stress (CRSS) for basal slip and twinning modes. The twin volume fraction changes were quantified from the intensity changes with applied load. We observed that the twin volume fraction changes with plastic strain is sensitive to the initial texture, while the relative hardening of different deformation modes are considered as a secondary effect. We also found that the twin interior stresses were significantly smaller and consistent with the high twin back stresses in the presence of precipitates. We propose, based on a simple analytical equation, that the leading edge of the propagating twin have a Burgers vector equivalent to 100 twinning dislocations and when the propagating twin is blocked by a precipitate, relatively high resolved stress is required for bowing the twin dislocation and hence the propagation of the twin occurs by the dissociation of the leading edge of the twinning dislocation.

Grain boundary strengthening in strongly textured magnesium produced by hot rolling

The grain size dependence of the yield stress in hot rolled 99.87 pct magnesium sheets and rods was measured in the temperature range 77 K to 420 K. Hot rolling produced strong basal textures and, for a given grain size, the hot rolled material has a higher strength than extruded material. The yield strength-grain size relation in the above temperature range follows the Hall-Petch equation, and the temperature dependencies of the Hall-Petch constants σ0 and k are in support of the theory of Armstrong for hcp metals that the intercept σ0 is related to the critical resolved shear stress (CRSS) for basal slip (easy slip) and the slope k is related to the CRSS for prismatic slip (difficult slip) occurring near the grain boundaries. In the hot rolled magnesium, σ0 is larger and k is smaller than in extruded material, observations which are shown to result from strong unfavorable basal and favorable 1010 textures, respectively. Texture affects the Hall-Petch constants through its effect on the orientation factors relating them to the CRSS for the individual slip systems controlling them.

Microtribology and Friction-Induced Material Transfer in Layered MoS2 Nanoparticles Sprayed on a Steel Surface

Frictional performance of molybdenum disulfide (MoS2) particles sprayed on a substrate is investigated in a ball-on-disc tribometer. The ability of large (similar to 2 mu m) and small (similar to 50 nm) particles to generate low-friction transfer film is investigated with a view to elucidate the requirement for film formation. Particle migration, particle stability in the contact region, oxidation potential, and particle adhesion to the substrate are explored within a span of operating parametersp; normal load, and sliding velocity. It is found that the larger particles are able to migrate to the contact to raise a homogeneous but nonuniform low-friction transfer film that flows plastically to yield large contact areas, which aid in wear protection. Within the present load and speed range, the inability of small particles to stay in the contact region and undergo basal slip militates against the formation of a low-friction transfer film.

Room-temperature equal channel angular extrusion of pure magnesium

In this paper, we demonstrate a way to impart severe plastic deformation to magnesium at room temperature to produce ultrafine grain size of similar to 250 nm through equal channel angular extrusion (ECAE). The strategy to deform magnesium at lower temperature or to achieve such grain sizes has been proposed as: (i) to obtain a suitable initial orientation with high Schmid factor for basal slip and low Schmid factor for pyramidal/prismatic slip; (ii) to take advantage of low stacking fault energy of basal and high stacking fault energies of prismatic/pyramidal planes in order to relatively work-harden the basal plane with respect to the pyramidal/prismatic plane; and (iii) to lower the temperature of deformation in steps, leading to continual refinement of grains, resulting in finer grain size. The experimental as well as simulated texture of ECAE-processed samples indicate that the deformation mechanism leading to ultrafine grain size is slip-dominated. The recrystallization mechanism during ECAE has been found to be orientation-dependent. (C) 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Orientation dependence of the indentation impression morphology in a Mg alloy

The formation of anomalous indentations, with two opposite faces describing a pin-cushion effect and the other two faces normal, in long elongated grains of an extruded Mg-2Al-1Zn alloy is reported. Subsurface microstructural observations combined with Schmid factor calculations suggest that extension twinning accompanied by basal slip are the reasons for these. Johnson's expanding cavity model is invoked for further substantiation. (C) 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.