Array of subarrays using adaptive element patterns

This paper explores the use of subarrays as array elements. Benefits of such a concept include improved gain in any direction without significantly increasing the overall size of the array and enhanced pattern control. The architecture for an array of subarrays will be discussed via a systems approach. Individual system designs are explored in further details and proof of principle is illustrated through a manufactured examples.

Diseño de un array de antenas en tecnología microstrip

[ES]Este trabajo de fin de grado trata sobre el diseño de un array de antenas en tecnología microstrip para ser utilizado en la banda de 5 GHz del estándar de tecnologías inalámbricas IEEE 802.11a. Se buscará aplicar la teoría de arrays para conseguir la mayor ganancia posible, pero al mismo tiempo tratando de obtener un gran ancho de banda para que la antena sea óptima dentro de la mayor parte posible de la banda especificada. El proyecto partirá de un único parche microstrip para posteriormente ir evolucionando el diseño hasta llegar a un array de 2x2 elementos. Al primer diseño se le irán añadiendo progresivamente todos los componentes necesarios (red de adaptación, desfasadores, mayor número de parches, etc.) para poder ir estudiando las simulaciones a la vez que el diseño progresa. Todos los diseños se realizarán con el software ADS (Advanced Design System) de la compañía Agilent Technologies. Finalmente se fabricará el array diseñado y se medirá para contrastarlo con las simulaciones.

Operation of a high frequency piezoelectric ultrasound array with an application specific integrated circuit

Integration of a piezoelectric high frequency ultrasound (HFUS) array with a microfabricated application specific integrated circuit (ASIC) performing a range of functions has several advantages for ultrasound imaging. The number of signal cables between the array/electronics and the data acquisition / imaging system can be reduced, cutting costs and increasing functionality. Electrical impedance matching is also simplified and the same approach can reduce overall system dimensions for applications such as endoscopic ultrasound. The work reported in this paper demonstrates early ASIC operation with a piezocomposite HFUS array operating at approximately 30 MHz. The array was tested in three different modes. Clear signals were seen in catch-mode, with an external transducer as a source of ultrasound, and in pitch-mode with the external transducer as a receiver. Pitch-catch mode was also tested successfully, using sequential excitation on three array elements, and viable signals were detected. However, these were relatively small and affected by interference from mixed-signal sources in the ASIC. Nevertheless, the functionality and compatibility of the two main components of an integrated HFUS - ASIC device have been demonstrated and the means of further optimization are evident.

Detect and pointing algorithm's performance for a planar smart antenna array: a review

An adaptive antenna array combines the signal of each element, using some constraints to produce the radiation pattern of the antenna, while maximizing the performance of the system. Direction of arrival (DOA) algorithms are applied to determine the directions of impinging signals, whereas beamforming techniques are employed to determine the appropriate weights for the array elements, to create the desired pattern. In this paper, a detailed analysis of both categories of algorithms is made, when a planar antenna array is used. Several simulation results show that it is possible to point an antenna array in a desired direction based on the DOA estimation and on the beamforming algorithms. A comparison of the performance in terms of runtime and accuracy of the used algorithms is made. These characteristics are dependent on the SNR of the incoming signal.

Investigations on Ultrasonic Transducer Array Systems for NDE of Underwater Pipelines

The main objective of carrying out this investigation is to develop suitable transducer array systems so that underwater pipeline inspection could be carried out in a much better way, a focused beam and electronic steering can reduce inspection time as well. Better results are obtained by optimizing the array parameters. The spacing between the elements is assumed to be half the wavelength so that the interelement interaction is minimum. For NDT applications these arrays are operated at MHz range. The wavelengths become very small in these frequency ranges. Then the size of the array elements becomes very small, requiring hybrid construction techniques for their fabrication. Transducer elements have been fabricated using PVDF as the active, mild steel as the backing and conducting silver preparation as the bonding materials. The transducer is operated in the (3,3) mode. The construction of a high frequency array is comparatively complicated. The interelement spacing between the transducer elements becomes considerably small when high frequencies are considered. It becomes very difficult to construct the transducer manually. The electrode connections to the elements can produce significant loading effect. The array has to be fabricated using hybrid construction techniques. The active materials has to be deposited on a proper substrate and etching techniques are required to fabricate the array. The annular ring, annular cylindrical or other similar structural forms of arrays may also find applications in the near future in treatments were curved contours of the human body are affected.

Precise analysis of array usage in scientific programs

The automatic transformation of sequential programs for efficient execution on parallel computers involves a number of analyses and restructurings of the input. Some of these analyses are based on computing array sections, a compact description of a range of array elements. Array sections describe the set of array elements that are either read or written by program statements. These sections can be compactly represented using shape descriptors such as regular sections, simple sections, or generalized convex regions. However, binary operations such as Union performed on these representations do not satisfy a straightforward closure property, e.g., if the operands to Union are convex, the result may be nonconvex. Approximations are resorted to in order to satisfy this closure property. These approximations introduce imprecision in the analyses and, furthermore, the imprecisions resulting from successive operations have a cumulative effect. Delayed merging is a technique suggested and used in some of the existing analyses to minimize the effects of approximation. However, this technique does not guarantee an exact solution in a general setting. This article presents a generalized technique to precisely compute Union which can overcome these imprecisions.

A 20-channel receive-only mouse array coil for a 3 T clinical MRI system

A 20-channel phased-array coil for MRI of mice has been designed, constructed, and validated with bench measurements and high-resolution accelerated imaging. The technical challenges of designing a small, high density array have been overcome using individual small-diameter coil elements arranged on a cylinder in a hexagonal overlapping design with adjacent low impedance preamplifiers to further decouple the array elements. Signal-to-noise ratio (SNR) and noise amplification in accelerated imaging were simulated and quantitatively evaluated in phantoms and in vivo mouse images. Comparison between the 20-channel mouse array and a length-matched quadrature driven small animal birdcage coil showed an SNR increase at the periphery and in the center of the phantom of 3- and 1.3-fold, respectively. Comparison with a shorter but SNR-optimized birdcage coil (aspect ratio 1:1 and only half mouse coverage) showed an SNR gain of twofold at the edge of the phantom and similar SNR in the center. G-factor measurements indicate that the coil is well suited to acquire highly accelerated images.

On the design and measurement of a novel non-orthogonal multi-beam network for triangular arrays of three radiating elements

An innovative dissipative multi-beam network for triangular arrays of three radiating elements is proposed. This novel network provides three orthogonal beams in θ0 elevation angle and a fourth one in the broadside steering direction. The network is composed of 90º hybrid couplers and fixed phase shifters. In this paper, a relation between network components, radiating element distance and beam steering directions will be shown. Application of the proposed dissipative network to the triangular cells of three radiating elements that integrate the intelligent antenna GEODA will be exhibited. This system works at 1.7 GHz, it has a 60º single radiating element beamwidth and a distance between array elements of 0.57 λ. Both beam patterns, theoretical and simulated, obtained with the network will be depicted. Moreover, the whole system, dissipative network built with GEODA cell array, has been measured in the anechoic chamber of the Radiation Group of Technical University of Madrid, demonstrating expected performance.

Study of a new 4×3 beam forming network for triangular arrays of three radiating elements

An innovative dissipative multi-beam network for triangular arrays of three radiating elements is proposed. This novel network provides three orthogonal beams in θ0 elevation angle and a fourth one in the broadside steering direction. The network is composed of 90º hybrid couplers and fixed phase shifters. In this paper, a relation between network components, radiating element distance and beam steering directions will be shown. Application of the proposed dissipative network to the triangular cells of three radiating elements that integrate the intelligent antenna GEODA will be exhibited. This system works at 1.7 GHz, it has a 60º single radiating element beamwidth and a distance between array elements of 0.57λ. Both beam patterns, theoretical and simulated, obtained with the network will be depicted. Moreover, the whole system, dissipative network built with GEODA cell array, has been measured in the anechoic chamber of the Radiation Group of Technical University of Madrid, demonstrating expected performance

Investigations into a wideband spatial beamformer employing a rectangular array of planar monopoles

This paper presents a rectangular array antenna with a suitable signal-processing algorithm that is able to steer the beam in azimuth over a wide frequency band. In the previous approach, which was reported in the literature, an inverse discrete Fourier transform technique was proposed for obtaining the signal weighting coefficients. This approach was demonstrated for large arrays in which the physical parameters of the antenna elements were not considered. In this paper, a modified signal-weighting algorithm that works for arbitrary-size arrays is described. Its validity is demonstrated in examples of moderate-size arrays with real antenna elements. It is shown that in some cases, the original beam-forming algorithm fails, while the new algorithm is able to form the desired radiation pattern over a wide frequency band. The performance of the new algorithm is assessed for two cases when the mutual coupling between array elements is both neglected and taken into account.

A wideband array antenna with beam-steering capability using real valued weights

This article presents an array antenna with beam-steering capability in azimuth over a wide frequency band using real-valued weighting coefficients that can be realized in practice by amplifiers or attenuators. The described beamforming scheme relies on a 2D (instead of 1D) array structure in order to make sure that there are enough degrees of freedom to realize a given radiation pattern in both the angular and frequency domains. In the presented approach, weights are determined using an inverse discrete Fourier transform (IDFT) technique by neglecting the mutual coupling between array elements. Because of the presence of mutual coupling, the actual array produces a radiation pattern with increased side-lobe levels. In order to counter this effect, the design aims to realize the initial radiation pattern with a lower side-lobe level. This strategy is demonstrated in the design example of 4 X 4 element array. (C) 2005 Wiley Periodicals. Inc.

Wideband beam and steering using a rectangular array of planar monopoles

This article presents the design of a wideband rectangular array of planar monopoles, which is able to steer its beam and nulls over a wide frequency band using real-valued weights. These weights can be realized in practice by amplifiers or attenuators leading to a low cost development of a wideband array antenna with beam and null steering capability. The weights are determined by applying an inverse discrete Fourier transform to an assumed radiation pattern. This wideband beam and null forming concept is verified by full electromagnetic simulations which take into account mutual coupling effects between the array elements.

Applications of Microwave Antenna Array for Wireless Power Transmission and Radar Imaging in Complex Environment

Thesis (Ph.D.)--University of Washington, 2016-08

Closed-form design equations for decoupling networks of small arrays

Small element spacing in compact arrays results in strong mutual coupling between the array elements. A decoupling network consisting of reactive cross-coupling elements can alleviate problems associated with the coupling. Closed-form design equations for the decoupling networks of symmetrical arrays with two or three elements are presented.