Análise de propriedades térmicas e mecânicas de compósitos de argamassa e resíduo de borracha

Although already to exist alternative technique and economically viable for destination of used tires, quantitative data on properties of constructive elements that use the rubber waste as aggregate still are restricted. In the present work, the waste proceeding from industry of retreading as material for manufacture of composite destined to the production of constructive elements was considered. Mechanical and thermal properties of mortar had been analyzed Portland cement with addition of waste without treatment, in the ratios of 10%, 20% and 30% in mass in relation to the mass of the cement, substituting the aggregate in the trace in mortar 1:5 mass cement and sand. The size of the used residue varied between 0,30mm and 4,8mm (passing in the bolter 4,8mm and being restrained in the one of 0,30mm), being it in the formats fibers and granular. The influences of the size and the percentage of residue added to the mortar (in substitution to the aggregate) in the thermal and mechanical properties had been considered. Assays of body-of-test in thestates had been become fullfilled cool (consistency index) and hardened (absorption of water for capillarity, strength the compression, traction and strength flexural). The work is centralized in the problem of the relation thermal performance /strength mechanics of used constructive systems in regions of low latitudes (Been of the Piauí), characterized for raised indices of solar radiation.

Análise de propriedades térmicas e mecânicas de compósitos de argamassa e resíduo de borracha

Although already to exist alternative technique and economically viable for destination of used tires, quantitative data on properties of constructive elements that use the rubber waste as aggregate still are restricted. In the present work, the waste proceeding from industry of retreading as material for manufacture of composite destined to the production of constructive elements was considered. Mechanical and thermal properties of mortar had been analyzed Portland cement with addition of waste without treatment, in the ratios of 10%, 20% and 30% in mass in relation to the mass of the cement, substituting the aggregate in the trace in mortar 1:5 mass cement and sand. The size of the used residue varied between 0,30mm and 4,8mm (passing in the bolter 4,8mm and being restrained in the one of 0,30mm), being it in the formats fibers and granular. The influences of the size and the percentage of residue added to the mortar (in substitution to the aggregate) in the thermal and mechanical properties had been considered. Assays of body-of-test in thestates had been become fullfilled cool (consistency index) and hardened (absorption of water for capillarity, strength the compression, traction and strength flexural). The work is centralized in the problem of the relation thermal performance /strength mechanics of used constructive systems in regions of low latitudes (Been of the Piauí), characterized for raised indices of solar radiation.

A influência das condições de cura nas propriedades das argamassas de cal para revestimentos antigos

Dissertação elaborada no Laboratório Nacional de Engenharia Civil (LNEC) para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Edificações no âmbito do protocolo de cooperação entre o ISEL e o LNEC

Incorporação de resíduos cerâmicos vidrados em argamassas bastardas: estudo de propriedades físicas e mecânicas

Dissertação de Natureza Científica para obtenção do grau de Mestre em Engenharia Civil Perfil de Edificações

Durabilidade da argamassa mista de revestimento interno contendo dregs-grits em substituição à areia

This paper concerns about the durability of new material in construction. It is noteworthy the fact that increases increasingly searching for alternative materials that do not depend only of natural resources and at the same time be an alternative for reuse of industrial waste. Since the construction materials have a long life and a high cost of civil works and maintenance, it is crucial to estimate the behavior of a new product. Thus , this work discuss the durability of mixed mortar lining , made with waste from the process Kraft pulp production , known as dregs and grits , in partial replacement of sand. Tests were conducted to simulate conditions as adverse environments of constant heat and fire, with the aim of analyzing the behavior of mortar mixed matched the behavior of standard mortar

Síntese, aplicação e avaliação do efeito do teor de fósforo da celulose fosfatada em argamassa de alvenaria com aditivo comercial a base de hidroxi-etil-metil celulose (HEMC)

Generally, cellulose ethers improves mortar properties such as water retention, workability and setting time, along with adherence to the substrate. However, a major disadvantage of the addition of cellulose ethers in mortars is the delay in hydration of the cement. In this paper a cellulose phosphate (Cp) was synthesized water soluble and has been evaluated the effect of their incorporation into mortar based on Portland cement. Cellulose phosphate obtained was characterized by spectrophotometry Fourier transform infrared (FTIR), X-ray diffraction (XRD), elemental analysis and scanning electron microscopy (SEM). Mortar compositions were formulated with varying phosphorus content in cellulose and cellulose phosphate concentrations, when used in partial or total replacement of the commercial additive based hydroxyethyl methyl cellulose (HEMC). The mortars formulated with additives were prepared and characterized by: testing in the fresh state (consistency index, water retention, bulk density and air content incorporated) and in the hardened state (absorption by capillarity, density, flexural and compression strength). In mixtures the proportion of sand:cement of 1:5 (v / v) and factor a / c = 1.31 and water were held constant. Overall, the results showed that the celluloses phosphates employed in mortars added acted significantly when partially substituting the commercial additive. With regard to consistency index, water retention and bulk density in the fresh state and absorption by capillarity and bulk density apparent in the hardened state, showed no appreciable differences as compared to the commercial additive. The incorporated air content in the fresh state reduced markedly, but did not affect other properties. The mortars with cellulose phosphate, partially replacing the commercial additive showed an improvement of the properties of flexural strength and compressive strength

Desenvolvimento de argamassa para restauração utilizando resíduo do polimento do porcelanato

The coatings mortars are essential elements of building structures because they execute an important role in protecting walls and are particularly exposed to aggressive action responsible for its degradation over time. The importance of wall coverings has been the subject of discussion and analysis in the conservation and rehabilitation of old buildings. Are sometimes removed and replaced with inappropriate solutions of constructive point of view or architecture. The most commonly used coatings on walls of old buildings is based on traditional hydraulic lime mortars. The present study aims at the formulation of new lime- based mortars and aerial fine aggregate, in order to contribute to a better field of conservation and restoration mortar coating of old buildings. Residue was used for polishing porcelain as fine aggregate, replacing the aggregate (sand), in percentages 05-30% by mass. We conducted a thorough evaluation of the mortar properties in fresh and hardened state by comparing the performance of the same with a reference mortar. The residue used was characterized as the density, bulk density, and particle size laser, scanning electron microscopy, X-ray diffraction and X-ray fluorescence. Formulations were produced 7, 6 with residue and one commonly used formulation, which served as a reference. In the formulations of lime mortars air (hydrated lime powder CH-I) has been adopted a stroke volume (1:3) with constant binder, was varied and the water / binder and aggregate and waste. For evaluation of mortars fresh, proceeded to consistency analysis, specific gravity, water retention and air content embedded. In the hardened state assays were performed in specific gravity, water retention, modulus of elasticity, tensile strength in bending, compressive strength, water absorption by capillary action, adhesion, tensile strength, resistance to shrinkage and salts by of crystallization trials with resources chloride solution, nitrate and sulfate all sodium in prismatic at 90 days of age, in addition to the micro structural analysis of mortars. Based on the results we can see that the mortar formulated with 10% content of waste and the reference free retraction feature more stable closer to neutrality. The composition of 10% was obtained better performance against the action of the salt crystallization. The mortar with 15% residue obtained better density, lower air content embedded and high capacity for water retention developing good workability. The replacement of 20% of waste generates a satisfactory utilization of resistance to compression, flexion and traction grip the base. And, finally, it can be seen that the mortar with 10, 15 and 20% residual show, in principle, good suitability as coatings, thus enabling a final result consistent with durability, workability and aesthetics developing therefore a material with better performance to repair or replace existing mortars in old buildings

Análise de Argamassas Com Substituição Parcial do Cimento Portland Por Cinza Residual de Lenha de Algaroba

With the increase in cement consumption, it has quickly become one of the inputs most consumed by mankind over the last century. This has caused an increase in CO2 emissions, as cement production releases large quantities of this gas into the atmosphere. Adding this fact to the growing consciousness of environmental preservation, it has led to a search for alternatives to cement to complement its derivatives, in the form of waste materials like the ashes. This research aimed to analyze the properties of mortars in fresh and hardened state with partial replacement of Portland cement by residual algaroba wood ash (CRLA) potteries produced by the state of Rio Grande do Norte. The CRLA was collected and sieved, where part of it was ground and characterized in comparison with that just sifted, being characterized according to its chemical composition, grain size, fineness, density, bulk density and index of pozzolanic activity. It was found that the wood ash does not act as pozzolan, and grinding it has not changed its characteristics compared to those just sifted, not justifying its use. Two traces were adopted for this research: 1:3 (cement: fine sand) and 1:2:8 (cement: hydrated lime: medium sand); both in volume, using as materials the CRLA just sifted, CP II F-32 Portland cement, CH-I hydrated lime, river sand and water from the local utility. For each trace were adopted six percentages of partial replacement of cement for wood ash: 0% (control) 5%, 7%, 10%, 12% and 15%. In the fresh state, the mortars were tested towards their consistency index and mass density. In the hardened state, they were tested towards their tensile strength in bending, compressive strength and tensile adhesion strength, and its mass density in the hardened state. The mortar was also analyzed by scanning electron microscopy and X-ray diffraction. Furthermore, it was classified according to NBR 13281 (2005). The results showed that up to a content of 5% substitution and for both traces, the residual algaroba wood ash can replace Portland cement without compromising the mortars microstructure and its fresh and hardened state

Utilização do pó de pedra basáltica em substituição à areia natural do concreto

Pós-graduação em Engenharia Civil - FEIS

Influência do teor de cinza volante na reologia de argamassa de assentamento: fabricado com reciclagem de resíduos

As argamassas podem ser consideradas como um conjunto de partículas sólidas em suspensão (agregado miúdo), aglomerantes e água (pasta de cimento). Sendo assim, seu comportamento reológico durante a cura pode ser influenciado por fatores como a granulometria, composição e teor de água incorporado. Este trabalho estudou as características reológicas de seis composições de argamassas, em função do teor de cinza volante, como material de atividade pozolânica, em substituição parcial do cimento. A argamassa estudada utilizou como base agregado o resíduo da construção civil (RCC), devidamente caracterizado por difratometria e fluorescência de raios-X. Formularam-se composições de argamassas para os ensaios reológicos com adição de resíduo de construção civil (RCC) nas proporções de 95, 90, 85, 80, 75 e 70%; cinzas volantes (CV) 0, 5, 10, 15, 20 e 25% e 5% de Cimento Portland Comum (CP II- E 32), sendo que em cada amostra foi incorporado 35% de água. Utilizou-se o viscosímetro modelo VT 550, com sensor tipo cilindros coaxiais SV₁ – Haake a temperatura de 28ºC. Para avaliar o tempo de cura do material programou-se uma taxa de cisalhamento constante 53,4 s^-1 em 1h e 45min, sendo avaliado o torque em intervalos de 15min. Para a elaboração das curvas de fluxo e curvas de histerese, utilizou-se a taxa de cisalhamento entre 0 e 600 s^-1 no intervalo de tempo de 120s. Os resultados mostraram que a incorporação de cinza volante foi o principal fator para aumento do torque no tempo de cura das argamassas e mudança do comportamento de reópetico para tixotrópico, nos traços analisados. Os dados experimentais das formulações propostas ajustaram-se ao modelo reológico de Herschel-Bulkley.

Caracterização dos finos de areia de uma fundição e sua incorporação em argamassa de cimento

Pós-graduação em Engenharia Civil e Ambiental - FEB

Tecnologia construtiva de revestimento externo de argamassa com projeção contínua.

Os métodos construtivos de revestimento externo produzidos com argamassa vêm evoluindo ao longo do tempo, apresentando como maior mudança a substituição da aplicação manual pela projeção mecânica. Atualmente destaca-se no mercado o sistema de execução de revestimento externo com argamassa industrializada e projeção mecânica contínua com bombas helicoidais. Por se tratar de uma tecnologia ainda não muito utilizada pelas construtoras brasileiras, faltam dados confiáveis acerca de seu potencial de ganho de produtividade, redução de perdas, diminuição de contingente de mão de obra, exigências de infraestrutura para aplicação e custos envolvidos. Sem parâmetros confiáveis, adotar a tecnologia significa assumir um nível de risco elevado e isto dificulta a tomada de decisão por parte das construtoras e, por consequência, dificulta-se a evolução tecnológica. Buscando contribuir para o necessário avanço nas tecnologias de produção de revestimentos de edifícios, o objetivo desta pesquisa é estabelecer parâmetros em relação à tecnologia de produção de revestimentos de fachada que empregam argamassa com projeção contínua. Para tanto, buscou-se informações em referências como teses, dissertações, textos técnicos, normas nacionais, dentre outras, bem como, acompanhou-se e avaliou-se os resultados da implantação de um método construtivo de revestimento de argamassa com projeção mecânica contínua em uma construtora de São Paulo. Foram realizados um protótipo e um piloto que contribuíram para o desenvolvimento da tecnologia por meio de apresentação de soluções para os problemas encontrados, do levantamento de melhores práticas e de dados para o cálculo de índices de produtividade e perda. Buscou-se, portanto, a consolidação da tecnologia de projeção contínua na construtora anteriormente mencionada e no mercado em geral.

Síntese, aplicação e avaliação do efeito do teor de fósforo da celulose fosfatada em argamassa de alvenaria com aditivo comercial a base de hidroxi-etil-metil celulose (HEMC)

Generally, cellulose ethers improves mortar properties such as water retention, workability and setting time, along with adherence to the substrate. However, a major disadvantage of the addition of cellulose ethers in mortars is the delay in hydration of the cement. In this paper a cellulose phosphate (Cp) was synthesized water soluble and has been evaluated the effect of their incorporation into mortar based on Portland cement. Cellulose phosphate obtained was characterized by spectrophotometry Fourier transform infrared (FTIR), X-ray diffraction (XRD), elemental analysis and scanning electron microscopy (SEM). Mortar compositions were formulated with varying phosphorus content in cellulose and cellulose phosphate concentrations, when used in partial or total replacement of the commercial additive based hydroxyethyl methyl cellulose (HEMC). The mortars formulated with additives were prepared and characterized by: testing in the fresh state (consistency index, water retention, bulk density and air content incorporated) and in the hardened state (absorption by capillarity, density, flexural and compression strength). In mixtures the proportion of sand:cement of 1:5 (v / v) and factor a / c = 1.31 and water were held constant. Overall, the results showed that the celluloses phosphates employed in mortars added acted significantly when partially substituting the commercial additive. With regard to consistency index, water retention and bulk density in the fresh state and absorption by capillarity and bulk density apparent in the hardened state, showed no appreciable differences as compared to the commercial additive. The incorporated air content in the fresh state reduced markedly, but did not affect other properties. The mortars with cellulose phosphate, partially replacing the commercial additive showed an improvement of the properties of flexural strength and compressive strength

Desenvolvimento de argamassa para restauração utilizando resíduo do polimento do porcelanato

The coatings mortars are essential elements of building structures because they execute an important role in protecting walls and are particularly exposed to aggressive action responsible for its degradation over time. The importance of wall coverings has been the subject of discussion and analysis in the conservation and rehabilitation of old buildings. Are sometimes removed and replaced with inappropriate solutions of constructive point of view or architecture. The most commonly used coatings on walls of old buildings is based on traditional hydraulic lime mortars. The present study aims at the formulation of new lime- based mortars and aerial fine aggregate, in order to contribute to a better field of conservation and restoration mortar coating of old buildings. Residue was used for polishing porcelain as fine aggregate, replacing the aggregate (sand), in percentages 05-30% by mass. We conducted a thorough evaluation of the mortar properties in fresh and hardened state by comparing the performance of the same with a reference mortar. The residue used was characterized as the density, bulk density, and particle size laser, scanning electron microscopy, X-ray diffraction and X-ray fluorescence. Formulations were produced 7, 6 with residue and one commonly used formulation, which served as a reference. In the formulations of lime mortars air (hydrated lime powder CH-I) has been adopted a stroke volume (1:3) with constant binder, was varied and the water / binder and aggregate and waste. For evaluation of mortars fresh, proceeded to consistency analysis, specific gravity, water retention and air content embedded. In the hardened state assays were performed in specific gravity, water retention, modulus of elasticity, tensile strength in bending, compressive strength, water absorption by capillary action, adhesion, tensile strength, resistance to shrinkage and salts by of crystallization trials with resources chloride solution, nitrate and sulfate all sodium in prismatic at 90 days of age, in addition to the micro structural analysis of mortars. Based on the results we can see that the mortar formulated with 10% content of waste and the reference free retraction feature more stable closer to neutrality. The composition of 10% was obtained better performance against the action of the salt crystallization. The mortar with 15% residue obtained better density, lower air content embedded and high capacity for water retention developing good workability. The replacement of 20% of waste generates a satisfactory utilization of resistance to compression, flexion and traction grip the base. And, finally, it can be seen that the mortar with 10, 15 and 20% residual show, in principle, good suitability as coatings, thus enabling a final result consistent with durability, workability and aesthetics developing therefore a material with better performance to repair or replace existing mortars in old buildings

Utilização de óleos de origem vegetal em substituição aos derivados de petróleo em composições de borracha natural (NR)

A partir da publicação, em 1994, de um relatório que afirmava que a presença de óleos aromáticos pesados, com altos teores de compostos policíclicos, em formulações de borrachas estaria relacionada ao desenvolvimento de doenças como o câncer, associado ao fato da crescente conscientização ambiental na fabricação de produtos elastoméricos, foi iniciado um estudo sobre a substituição do óleo aromático de origem do petróleo por óleos vegetais de menor risco. Nessa Dissertação de Mestrado foi proposta a substituição do óleo aromático derivado do petróleo por óleos vegetais como o de tungue, palma e linhaça, em composições de borracha natural (NR) contendo diferentes teores do copolímero de butadieno-estireno (0, 10 e 50 phr) e diferentes tipos de carga (negro de fumo N330 e negro de fumo N375). As composições obtidas foram avaliadas quanto a propriedades reométricas, mecânicas e fractográficas. Foi observado que não houve variação significativa na viscosidade Mooney, na resistência à tração, no alongamento na ruptura e na dureza Shore das composições de NR SBR1502 quando o óleo aromático foi substituído pelos óleos vegetais, quando diferentes negros de fumo foram utilizados como carga reforçante e quando foram utilizados teores crescentes de SBR1502. Por outro lado, a resistência ao rasgamento das composições de NR SBR1502 apresentaram melhores resultados quando o negro de fumo N375 foi utilizado. A adição de teores crescentes de SR 1502 levou à diminuição dos valores de rasgo. A natureza do óleo utilizado influenciou esse resultado e melhores valores foram obtidos com o óleo de tungue. Os resultados obtidos foram corroborados pela morfologia do material, avaliadas por microscopia eletrônica de varredura