Estudo e seleção de um aparelho de ar condicionado para ônibus

The study and selection of an equipment of air conditioner for any type of environment, should be made without overestimate or undersizing the project. The undersizing does not provide an adequate comfort temperature if the environment is too hot because the air conditioner does not remove all the heat necessary in the environment. But if the project is oversized, energy consumption is higher and there is an unnecessary cost. To prevent these failures is necessary to make a calculation of the thermal load on the environment and choose the equipment that has a higher cooling capacity than the calculated heat load and closer to the calculated heat load. In this graduate work will be chosen an air-conditioned equipment for bus, showing the calculations made for the thermal load for various types of heat gain in this type of vehicle. The thermal load on vehicles is more complicated to calculate than in areas because there are several factors that vary with the movement of the vehicle. It will also explain the compression refrigeration cycle, which is the cooling system used in vehicles because it is weightless, compact and lower cost. From the calculated heat load, it will be chosen an air conditioner that best suits the project and, finally, a brief presentation of the selected equipment will be made

Controle de qualidade e levantamento radiométrico em aparelho de Raios-X médico convencional

Along with the advance of technology, in terms of the expansion of medical exams that uses the ionizing radiation for diagnosis, there is also the concern about quality control for maintaining quality in radiographic imaging and for delivering low dose to the patient. Based on the Federal Order 453 of the Secretariat of Health Surveillance, which takes account of the practical and justification of individual medical exposures, the optimization of radiological protection, limitation of individual dose, and the prevention of accidents, were done through this paper radiodiagnostic tests on medical equipment in order to accept it or not, according to SVS-453. Along with the help and support of P&R Consulting and Medical Physics Marilia, SP, were made Quality Control and Radiometric Control in equipment from various cities across the state of São Paulo. The equipment discussed in this work is classified as conventional X-ray. According to the Federal Order SVS-453, the quality control in the program of quality assurance should include the following minimum set of constancy tests, with following minimum frequency: biennial tests for representative values of dose given to the patients of radiography and CT performed in the service; annual tests for accuracy of the indicator tube voltage (kVp), accuracy of exposure time, half-value layer, aligning the central axis of the beam of x-ray tube, performance (mGy / mA.min.m²), linearity of the rate of kerma on air with the mAs, reproducibility of the kerma on air rates, reproducibility of the automatic exposure, focal spot size, integrity of accessories and clothing for individual protection; semiannually for collimation system accuracy; weekly for temperature processing system and sensitometry processing system. For the room Radiometric Survey it was done a sketch...(Complete abstract click electronic access below)

Tratamento da classe II hiperdivergente com o aparelho extra bucal de Thurow modificado

Objectives: natural dentofacial changes and that induced by the Thurow modified extra oral appliance (TMEOA) were evaluated in this prospective study. Methodology: the data consisted of fifteen Class II division 1 children 7 to 10 years old, with anterior open bite and hiperdivergent facial pattern treated with the Thurow appliance and of fifteen Class II division 1 children followed longitudinally from 6 to 12 years of age without treatment (Burlington Growth Centre, Toronto University, Canada). The analyses were based in traditional measurements obtained in lateral cephalometric radiographs scanned with the aid of the software Radiocef Studio®. Radiographs were taken in the beginning and after 1 year of treatment for the treated group and at the 6, 9 and 12 years of age for the control group. Results: the data analysis showed that the TMEOA significantly reduced the SNA, ANB, AOBO, SNPOc SNPM, SGO/NMe, OJ e OB. On the other hand the appliance did not interfere with the SNB e SNPP. The natural growth promoted significant change in the ANB, AOBO, SNPOc, OJ e OB from 6 to 9 years and in the SNB, SNPOc e SGo/NMe from 9 to 12 years. The restriction of the maxillary growth (SNA), reduction of the skeletal discrepancy (ANB) and the reduction of the overjet (OJ) were significant with the treatment considering the natural growth as verified in the control group. Conclusion: the TMEOA corrected the skeletal Class II malocclusion by maxillary restriction, reducing the overjet, closing the anterior open bite and decreasing both the hyper divergent facial pattern and mandible plane inclination.

Aparelho extrabucal como recurso auxiliar para alinhamento e nivelamento no tratamento orto cirúrgico de má oclusão classe III esquelética

When well indicated, the orthodontic surgical approach is the ideal treatment mean for Skeletal Class III adult patients. To improve facial esthetic results from orthognatic surgery, the leveling and alignment of maxillary dental arch must be achieved with minimal inclination and projection or even retro-inclination of anterior upper teeth. During a pre-surgical phase of 12 months, headgear bilateral force of 150 g/F was applied to the upper molars of a 22 years old male compliant patient with Class III skeletal malocclusion, to provide an upper teeth control of mesial tipping and projection during alignment and leveling. The ideal occlusal parameters required for surgical procedure were achieved without dental extractions permitting a total treatment period of 37 months. The outcomes remained stable over 3 years follow up after the removal of the appliance. The results indicate that, although headgear use depends greatly on patient compliance, when well indicated it is an interesting alternativetopromote dentaldecompensationon pre-surgical period, in order to allow surgical correction of skeletal Class III malocclusion.

Aparelho Herbst x osteotomia sagital mandibular bilateral no tratamento do padrão II, classe II, divisão 1 em adultos: relato de casos

Two treatment options are available for adult patients with skeletal Class II malocclusion caused by mandibular deficiency: combined mandibular advancement surgery and orthodontic treatment or mandibular advancement appliance. This study aimed to analyze the effects of two therapeutic modalities of Class II malocclusion treatment with mandibular deficiency. Two distinct individuals with Class II malocclusion division 1 and mandibular deficiency were treated after growth spurt. The first individual used the Herbst appliance as a therapeutic option and the second individual was treated with bilateral sagittal osteotomy. The cephalometric, occlusion and face results were evaluated for both individuals. Correction of Class II malocclusion was observed on both Herbst and surgery patients resulting on a normal occlusal relationship with normal overjet and overbite. Therefore it was concluded that Herbst appliance can be used to treat borderline skeletal Class II in adult patients.

Avaliação do índice de Litle em indivíduos que utilizaram o aparelho funcional T4K

The study aimed to assess the degree of dental crowding correction on the lower anterior region of patients treated with T4k functional appliance using Little’s irregularity index. Twenty caucasian patients of both gender (10 female and 10 male) were selected. They featured malocclusion Class I and II in mixed dentition, with chronological age between 5.7 and 11 years. The treatment lasted from 1 year and 11 months up to 3 years and 11 months. Lower anterior crowding was measured using Little’s irregularity index. Measurements were obtained on study models achieved before and after functional orthopedic therapy, using a digital caliper in millimeters and placed parallel to the occlusal plane. Overjet and overbite measurements were also performed using a caliper. Results demonstrated that the therapy provided significant decrease in overjet (average = 1.55 mm) and also in the irregularity index (average = 1.23 mm). There was a nonsignificant raise in overbite. There was no relation between the studied variables and the treatment period or even with the patient’s age in the beginning of the therapy. The treatment with T4k resulted on reduction and improvement of dental crowding.

Efeitos do aparelho de Herbst no tratamento proecoce da má oclusão classe II de Angle

Due to its high prevalence in general population, Angle Class II malocclusion has been widely studied by several authors, as well as the methods for its treatment. Among the possible treatment methods stands out the Herbst appliance. Reintroduced more than three decades ago in the orthodontics community, it became the most utilized appliance because it does not require patient compliance, and provides continued action through bilateral telescopic tubes. The objective of the present article was to demonstrate the early treatment of Class II Division 1 malocclusion with mandibular retrusion using Herbst appliance.

Eficiência do aparelho Herbst bandado na correção da Classe II divisão 1 -relato de caso

The current reports the case of a young patient with malocclusion Class II division 1 on permanent dentition treated in two stages, rthopedics and orthodontics, respectively. At first, the banded Herbst appliance was used duringa 7 months period, followed by a T4K appliance, Trainer for Kids used as retention, and on the second stage the corrective Orthodontics was performed. The results showed the acquirement of a Class I dental relationship, which was kept stable, with excellent intercuspation, even after 5 years of the removal of the Herbst appliance, as well as the correction of the overjet and the reduction of the facial profile convexity. It can be concluded that the Herbst appliance was very efficient in correcting the Class II malocclusion, long term, also providing a very favorable effect on the facial profile.

Estudo em telerradiografia em norma de 45º no tratamento da classe II com aparelho de Herbst

The aim of this retrospective study was to evaluate mandibular and maxillary changes induced by the use of Herbst applianceand by natural growth through oblique cephalometric radiographs in children with Class II division 1 malocclusion with mandibular retrusion. A sample of 49 individuals with age ranging from 8 to 10 years old (before growth peak) with Class II division 1, were into two groups: Herbst treated group (n=24) and control group (n=25). Both groups were paired for gender and chronological age. Statistical analysis was performed through Student’s t test. The Herbst appliance promoted the Class II correction in a 7 months period by mesialization of lower permanent first molars and distalization of upper permanent first molars. The Herbst appliance had no influence over the mandibular structure or the mandibular length. It was concluded that early treatment with Herbst appliance corrected the Class II malocclusion by means of dentoalveolar changes.

Tratamento da classe II divisão 2 com aparelho de Herbst após o pico de crescimento puberal

Patients with Class II division 2 malocclusion and mandibular retrusion have limited treatment options after the growth peak, such as surgical-orthodontic treatment or mandibular advancement devices. Among bite-jumping devices, the Herbst appliance allows greater increase of mandibular growth since it does not require patient compliance and allows continuous use. This case report presents the treatment of a Class II division 2 malocclusion in a patient after growth peak, performed in two stages. The first stage included the upper incisors proclination and overjet increase with multibracket appliance to benefit next stage. The second stage involved mandibular advancement using Herbst appliance aiming to correct the Class II molar relationship. The treatment resulted in a stable occlusion with periodontal health, normal functions and facial aesthetics improvement. Dental and skeletal changes arising from treatment could be assessed by cephalometric analysis and superimposition of pretreatment and post-treatment cephalometric tracings. Antero-posterior discrepancy was corrected by means of dental movement as well as by mandibular growth increment stimulated by the Herbst appliance.

Alterações dimensionais em pacientes submetidos à expansão rápida da maxila com aparelho do tipo Haas

The maxillary atresia is a alteration in the transverse dimension that can result in a unilateral or bilateral crossbite. For correction of atresia of the upper dental arch appliances with the intent to expand the arch of orthopedic or orthodontic manner are used, obtaining across-compatibility between the dental arches. The purpose of this study was to evaluate the dimensional changes of the maxillary in patients in the mixed dentition with atresia in the upper dental arch, using occlusal radiographs taken before, after rapid maxillary expansion and after removal of the appliance. Methods: the sample consisted of 35 patients who used the appliance type conventional Haas, in the mixed dentition, according to the standard protocol for installation, activation, containment and removal of the appliances rapid maxillary expansion. Results: the results confirm that the suture opening occurs in greater quantities in the anterior (4.3 mm) than posterior to (3.74 mm), representing a triangular opening of 7 degrees on average with the posterior opening 87% of the quantity of anterior opening. The molars region expanded about 5 mm, and the base bone 3.7 mm, representing a 74% bone expansion of the expansion teeth.

Aparelho de Herbst associado a aparelhos fixos: descrição de técnica

This paper aims at describeconstruction and installation sequences of a new design of appliance that allows continuously protraction of the mandible, using the telescopic mechanism of the Herbst appliance. This appliance has the advantage to be easily assembled by the orthodontist, without the necessity of molding and the assistance of a specialized laboratory, as well as the constant permanence in the mouth of the patient for being fixed.

Aparelho de Thurow modificado e aparelho ortodôntico fixo no tratamento da classe II com mordida aberta anterior

This work had aim to present two clinical cases with open bite Class II malocclusion that treated in the phase of the mixed dentition with the modified Thurow appliance and in the permanent dentition with fixed appliance. The dentoskeletal effects of these appliances were carefully analyzed with the aid of metallic implants inserted in both maxilla and mandible. The correction of the malocclusion and the improvement of the skeletal, dental and facial relationship were observed in both cases. The modified Thurow appliance followed by fixed-appliance as a two-phase treatment protocol revealed to be an effective treatment approach for the two young people that initially presented a Class II division 1 malocclusion associated to anterior open bite presented.

Avaliação das alterações dentárias e esqueléticas induzidas pelo uso do aparelho de Herbst no tratamento da classe II na dentadura mista: Revisão sistemática

Objective: evaluate the immediate dental and skeletal changes induced by the Herbst appliance on early treatment of Angle´s Class II malocclusion. Material and Method: several electronic databases such as Scopus, Pub Med, Medline, Cochrane Library, Lilacs and Scielo were searched. The abstracts that fullfilled the selection criteria were selected and those that did not provide enough information about these criteria were selected but the final decision of including them or not on the research, was taken after the complete reading of the article. The selection criteria were: clinical studies with Class II individuals, both male and female, with initial age of 7 to 10 years, treated with the Herbst appliance that analysed the dental and/or skeletal changes evaluated on lateral cephalometric radiographs; researches where the treatment performed did not involve extractions or surgical interventions; studies that included patients without syndromes or health concerns and articles published in English or Portuguese. Results and Conclusions: five articles were selected. The articles showed that significant changes happened in the mandibular sagittal lenght, on facial convexity angle, on maxillo-mandibular relationship, on retroclination of the upper incisors and on distal movement of the upper molars, on proclination of the lower incisors and on extrusion of the lower molars. The appliance exerted a limited effect on the anterior relocation of the maxillary complex and on facial heights. However, more studies about the performance of the Herbst appliance on early treatment of Class II are needed.

Modificação de forma e dimensões dos arcos superior e inferior obtidas em modelos de estudo após expansão rápida da maxila com o aparelho hyrax

The aim of an orthodontic treatment is the achievement of a balanced, esthetic and, most of all, stable, intra and inter arches relationship. A common problem observed in occlusion is posterior crossbite and atresic maxilla. This problem may be treated by slow expansion, rapid expansion or surgically assisted expansion. For the present study cast models of 14 children between 7 and 11 years old were evaluated. There were 7 male and 7 female subjects that presented posterior crossbite and needed rapid maxillary expansion. The Hyrax appliance performed the therapy for correction of this transversal alteration, which is a common possibility in the treatment of this malocclusion. It was observed that the distance between the upper first molars and upper cuspids increased significantly; the length of the upper arch decreased and its perimeter increased significantly. At the lower arch there were no dimensional changes.