Novas configurações de monopólios planares quase-fractais para sistemas de comunicações móveis

The characteristic properties of the fractal geometry have shown to be very useful for the construction of filters, frequency selective surfaces, synchronized circuits and antennas, enabling optimized solutions in many different commercial uses at microwaves frequency band. The fractal geometry is included in the technology of the microwave communication systems due to some interesting properties to the fabrication of compact devices, with higher performance in terms of bandwidth, as well as multiband behavior. This work describes the design, fabrication and measurement procedures for the Koch quasi-fractal monopoles, with 1 and 2 iteration levels, in order to investigate the bandwidth behavior of planar antennas, from the use of quasi-fractal elements printed on their rectangular patches. The electromagnetic effect produced by the variation of the fractal iterations and the miniaturization of the structures is analyzed. Moreover, a parametric study is performed to verify the bandwidth behavior, not only at the return loss but also in terms of SWR. Experimental results were obtained through the accomplishment of measurements with the aid of a vetorial network analyzer and compared to simulations performed using the Ansoft HFSS software. Finally, some proposals for future works are presented

Antenas de microfita com patch quase-fractal para aplicações em Redes WPAN/WLAN

The microstrip antennas are in constant evidence in current researches due to several advantages that it presents. Fractal geometry coupled with good performance and convenience of the planar structures are an excellent combination for design and analysis of structures with ever smaller features and multi-resonant and broadband. This geometry has been applied in such patch microstrip antennas to reduce its size and highlight its multi-band behavior. Compared with the conventional microstrip antennas, the quasifractal patch antennas have lower frequencies of resonance, enabling the manufacture of more compact antennas. The aim of this work is the design of quasi-fractal patch antennas through the use of Koch and Minkowski fractal curves applied to radiating and nonradiating antenna s edges of conventional rectangular patch fed by microstrip inset-fed line, initially designed for the frequency of 2.45 GHz. The inset-fed technique is investigated for the impedance matching of fractal antennas, which are fed through lines of microstrip. The efficiency of this technique is investigated experimentally and compared with simulations carried out by commercial software Ansoft Designer used for precise analysis of the electromagnetic behavior of antennas by the method of moments and the neural model proposed. In this dissertation a study of literature on theory of microstrip antennas is done, the same study is performed on the fractal geometry, giving more emphasis to its various forms, techniques for generation of fractals and its applicability. This work also presents a study on artificial neural networks, showing the types/architecture of networks used and their characteristics as well as the training algorithms that were used for their implementation. The equations of settings of the parameters for networks used in this study were derived from the gradient method. It will also be carried out research with emphasis on miniaturization of the proposed new structures, showing how an antenna designed with contours fractals is capable of a miniaturized antenna conventional rectangular patch. The study also consists of a modeling through artificial neural networks of the various parameters of the electromagnetic near-fractal antennas. The presented results demonstrate the excellent capacity of modeling techniques for neural microstrip antennas and all algorithms used in this work in achieving the proposed models were implemented in commercial software simulation of Matlab 7. In order to validate the results, several prototypes of antennas were built, measured on a vector network analyzer and simulated in software for comparison

Efeito da inclinação do plano de terra para antenas de microfita multicamadas com elementos parasitas fractais

This work presents the analysis of an antenna of fractal microstrip of Koch with dielectric multilayers and inclinations in the ground plane, whose values of the angles are zero degree (without inclinations), three, seven and twelve degrees. This antenna consists of three dielectric layers arranged vertically on each other, using feeding microstrip line in patch 1, of the first layer, which will feed the remaining patches of the upper layers by electromagnetic coupling. The objective of this work is to analyze the effects caused by increase of the angle of inclination of the ground plane in some antenna parameters such as return loss, resonant frequency, bandwidth and radiation pattern. The presented results demonstrate that with the increase of the inclination angle it is possible to get antennas with characteristics multiband, with bigger bandwidth, and improving the impedance matching for each case analyzed, especially the larger angle

Caracterização de superfícies seletivas de freqüência e de antenas fractais para aplicações em redes sem fio

This work aims to investigate the behavior of fractal elements in planar microstrip structures. In particular, microstrip antennas and frequency selective surfaces (FSSs) had changed its conventional elements to fractal shapes. For microstrip antennas, was used as the radiating element of Minkowski fractal. The feeding method used was microstrip line. Some prototypes were built and the analysis revealed the possibility of miniaturization of structures, besides the multiband behavior, provided by the fractal element. In particular, the Minkowski fractal antenna level 3 was used to exploit the multiband feature, enabling simultaneous operation of two commercial tracks (Wi-Fi and WiMAX) regulated by ANATEL. After, we investigated the effect of switches that have been placed on the at the pre-fractal edges of radiating element. For the FSSs, the fractal used to elements of FSSs was Dürer s pentagon. Some prototypes were built and measured. The results showed a multiband behavior of the structure provided by fractal geometry. Then, a parametric analysis allowed the analysis of the variation of periodicity on the electromagnetic behavior of FSS, and its bandwidth and quality factor. For numerical and experimental characterization of the structures discussed was used, respectively, the commercial software Ansoft DesignerTM and a vector network analyzer, Agilent N5230A model

Estudo de arranjos de antenas de microfita com Patch quase-fractal para comunicações sem fio

In this dissertation, are presented two microstrip antennas and two arrays for applications in wireless communication systems multiband. Initially, we studied an antenna and a linear array consisting of two elements identical to the patch antenna isolated. The shape of the patch used in both structures is based on fractal geometry and has multiband behavior. Next a new antenna is analyzed and a new array such as initial structure, but with the truncated ground plane, in order to obtain better bandwidths and return loss. For feeding the structures, we used microstrip transmission line. In the design of planar structures, was used HFSS software for the simulation. Next were built and measures electromagnetic parameters such as input impedance and return loss, using vector network analyzer in the telecommunications laboratory of Federal University of Rio Grande do Norte. The experimental results were compared with the simulated and showed improved return loss for the first array and also appeared a fourth band and increased directivity compared with the isolated antenna. The first two benefits are not commonly found in the literature. For structures with a truncated ground planes, the technique improved impedance matching, bandwidth and return loss when compared to the initial structure with filled ground planes. Moreover, these structures exhibited a better distribution of frequency, facilitating the adjustment of frequencies. Thus, it is expected that the planar structures presented in this study, particularly arrays may be suitable for specific applications in wireless communication systems when frequency multiband and wideband transmission signals are required.

Antenas cornetas para o satélite CosmoGal

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Electrónica e Telecomunicações

Análise e projeto de superfícies seletivas de frequência com elementos pré-fractais para aplicações em comunicações indoor

In this thesis, a frequency selective surface (FSS) consists of a two-dimensional periodic structure mounted on a dielectric substrate, which is capable of selecting signals in one or more frequency bands of interest. In search of better performance, more compact dimensions, low cost manufacturing, among other characteristics, these periodic structures have been continually optimized over time. Due to its spectral characteristics, which are similar to band-stop or band-pass filters, the FSSs have been studied and used in several applications for more than four decades. The design of an FSS with a periodic structure composed by pre-fractal elements facilitates the tuning of these spatial filters and the adjustment of its electromagnetic parameters, enabling a compact design which generally has a stable frequency response and superior performance relative to its euclidean counterpart. The unique properties of geometric fractals have shown to be useful, mainly in the production of antennas and frequency selective surfaces, enabling innovative solutions and commercial applications in microwave range. In recent applications, the FSSs modify the indoor propagation environments (emerging concept called wireless building ). In this context, the use of pre-fractal elements has also shown promising results, allowing a more effective filtering of more than one frequency band with a single-layer structure. This thesis approaches the design of FSSs using pre-fractal elements based on Vicsek, Peano and teragons geometries, which act as band-stop spatial filters. The transmission properties of the periodic surfaces are analyzed to design compact and efficient devices with stable frequency responses, applicable to microwave frequency range and suitable for use in indoor communications. The results are discussed in terms of the electromagnetic effect resulting from the variation of parameters such as: fractal iteration number (or fractal level), scale factor, fractal dimension and periodicity of FSS, according the pre-fractal element applied on the surface. The analysis of the fractal dimension s influence on the resonant properties of a FSS is a new contribution in relation to researches about microwave devices that use fractal geometry. Due to its own characteristics and the geometric shape of the Peano pre-fractal elements, the reconfiguration possibility of these structures is also investigated and discussed. This thesis also approaches, the construction of efficient selective filters with new configurations of teragons pre-fractal patches, proposed to control the WLAN coverage in indoor environments by rejecting the signals in the bands of 2.4~2.5 GHz (IEEE 802.11 b) and 5.0~6.0 GHz (IEEE 802.11a). The FSSs are initially analyzed through simulations performed by commercial software s: Ansoft DesignerTM and HFSSTM. The fractal design methodology is validated by experimental characterization of the built prototypes, using alternatively, different measurement setups, with commercial horn antennas and microstrip monopoles fabricated for low cost measurements

Desenvolvimento de monopolos quase-espirais para aplicações em sistemas UWB

This work is the analysis of a structure of the microstrip antenna designed for application in ultra wide band systems (Ultra Wideband - UWB). This is a prospective analytical study where they tested the changes in the geometry of the antenna, observing their suitability to the proposed objectives. It is known that the UWB antenna must operate in a range of at least 500 MHz, and answer a fractional bandwidth greater than or equal to 25%. It is also desirable that the antenna meets the specifications of track determined by FCC - Federal Communication Commission, which regulates the system in 2002 designating the UWB bandwidth of 7.5 GHz, a range that varies from 3.1 GHz to 10, 6 GHz. by setting the maximum power spectral density of operation in -41.3 dB / MHz, and defining the fractional bandwidth by 20%. The study starts of a structure of geometry in the form of stylized @, which evolves through changes in its form, in simulated commercial software CST MICROWAVE STUDIO, version 5.3.1, and then tested using the ANSOFT HFSS, version 9. These variations, based on observations of publications available from literature referring to the microstrip monopole planar antennas. As a result it is proposed an antenna, called Monopole Antenna Planar Spiral Almost Rectangular for applications in UWB systems - AMQEUWB, which presents simulated and measured results satisfactory, consistent with the objectives of the study. Some proposals for future work are mentioned

Análise teórica e experimental de superfícies seletivas de freqüência e suas aplicações em antenas planares

This work presents a theoretical and numerical analysis of structures using frequency selective surfaces applied on patch antennas. The FDTD method is used to determine the time domain reflected fields. Applications of frequency selective surfaces and patch antennas cover a wide area of telecommunications, especially mobile communications, filters and WB antennas. scattering parameters are obteained from Fourier Transformer of transmited and reflected fields in time domain. The PML are used as absorbing boundary condition, allowing the determination of the fields with a small interference of reflections from discretized limit space. Rectangular patches are considered on dielectric layer and fed by microstrip line. Frequency selective surfaces with periodic and quasi-periodic structures are analyzed on both sides of antenna. A literature review of the use of frequency selective surfaces in patch antennas are also performed. Numerical results are also compared with measured results for return loss of analyzed structures. It is also presented suggestions of continuity to this work

Arranjos Log-Periódicos Compactos em Microfita com Elementos Fractais de Koch

This work aims to present how the application of fractal geometry to the elements of a log-periodic array can become a good alternative when one wants to reduce the size of the array. Two types of log-periodic arrays were proposed: one with fed by microstrip line and other fed by electromagnetic coupling. To the elements of these arrays were applied fractal Koch contours, at two levels. In order to validate the results obtained some prototypes were built, which were measured on a vector network analyzer and simulated in a software, for comparison. The results presented reductions of 60% in the total area of the arrays, for both types. By analyzing the graphs of return loss, it was observed that the application of fractal contours made different resonant frequencies appear in the arrays. Furthermore, a good agreement was observed between simulated and measured results. The array with feeding by electromagnetic coupling presented, after application of fractal contours, radiation pattern with more smooth forms than the array with feeding by microstrip line

Desenvolvimento e otimização de antenas Vivaldi antipodais para aplicações a altas frequências.

Esta tese propõe a síntese e o estudo de uma nova técnica de cavidades de borda aplicada a antenas Vivaldi, com o intuito de melhorar suas características de diretividade. Embora as antenas do tipo Vivaldi possuam características diretivas, elas produzem radiações laterais indesejáveis, o que se reflete nos elevados índices de lóbulos laterais devido a correntes superficiais que fluem ao longo das bordas metalizadas nas laterais da antena. Estas correntes são a origem das radiações laterais que vêm sendo mitigadas pela aplicação de cavidades ressonantes, triangulares ou retangulares, que aprisionam tais correntes e, consequentemente, atenuam os lóbulos laterais, sem o incremento do lóbulo principal, uma vez que toda a energia dos lóbulos laterais é apenas confinada nos ressonadores e por isso literalmente perdida. Ao contrário desses esforços, este trabalho propõe cavidades radiantes tanto na forma de abertura exponencial, como na forma do fractais de Koch, que funcionam como radiadores auxiliares (antenas auxiliares), canalizando as correntes de borda e aproveitando-as para aumentar os níveis do lóbulo principal, mitigando os níveis de lóbulo lateral. A síntese desta nova técnica foi implementada em uma antena Vivaldi antipodal com características de baixa diretividade, como qualquer antena Vivaldi, o que foi corrigido e a aplicação da técnica de cavidades radiantes deu origem a duas novas antenas Vivaldis efetivamente diretivas. Os resultados foram obtidos através de simulações do modelo numérico no CST Microwave Studio e confirmados com medidas de laboratório, o que evidenciou a melhora das características de diretividade da antena pela aplicação da nova técnica de cavidades radiantes.

Estudo da variação da periodicidade e do acoplamento entre superfícies seletivas de frequência com elementos fractais e helicoidais em estruturas de multicamadas

This work aims to investigate the behavior of fractal and helical elements structures in planar microstrip. In particular, the frequency selective surfaces (FSSs) had changed its conventional elements to fractal and helical formats. The dielectric substrate used was fiberglass (FR-4) and has a thickness of 1.5 mm, a relative permittivity 4.4 and tangent loss equal to 0.02. For FSSs, was adopting the Dürer’s fractal geometry and helical geometry. To make the measurements, we used two antennas horns in direct line of sight, connected by coaxial cable to the vector network analyzer. Some prototypes were select for built and measured. From preliminary results, it was aimed to find practical applications for structures from the cascading between them. For FSSs with Dürer’s fractal elements was observed behavior provided by the multiband fractal geometry, while the bandwidth has become narrow as the level of iteration fractal increased, making it a more selective frequency with a higher quality factor. A parametric analysis allowed the analysis of the variation of the air layer between them. The cascading between fractal elements structure were considered, presented a tri-band behavior for certain values of the layer of air between them, and find applications in the licensed 2.5GHz band (2.3-2.7) and 3.5GHz band (3.3-3.8). For FSSs with helical elements, six structures were considered, namely H0, H1, H2, H3, H4 and H5. The electromagnetic behavior of them was analyzed separately and cascaded. From preliminary results obtained from the separate analysis of structures, including the cascade, the higher the bandwidth, in that the thickness of the air layer increases. In order to find practical applications for helical structures cascaded, the helical elements structure has been cascaded find applications in the X-band (8.0-12.0) and unlicensed band (5.25-5.85). For numerical and experimental characterization of the structures discussed was used, respectively, the commercial software Ansoft Designer and a vector network analyzer, Agilent N5230A model.

Radiação das antenas do serviço móvel celular e seu tratamento na legislação brasileira e de outros países

Consultoria Legislativa - Área XIV - Comunicação Social, Informática, Telecomunicações, Sistema Postal, Ciência e Tecnologia.

A quase conversação na comentosfera dos j-blogs: um estudo das interações na interface de comentários de quatro blogs jornalísticos institucionais

Este trabalho se situa na fronteira entre as áreas de Comunicação Social e Linguística e é voltado à investigação das interações ocorridas nos espaços dedicados à publicação de comentários de leitores em quatro blogs jornalísticos institucionais: Blog do Noblat, Blog MiriamLeitão.com, Blog do Reinaldo Azevedo e Blog do Josias de Souza. Com ele, pretende-se definir como cada leitor utiliza seus comentários para se relacionar com o jornalista autor do blog (o blogueiro), com outros leitores que também publicam suas opiniões (os leitores-comentaristas) e com o tópico tratado no texto (postagem) escrito pelo blogueiro. Além disso, considerando que autores da área de Comunicação Social discutem os blogs como um dispositivo amplamente conversacional, o propósito desta pesquisa é também esclarecer, à luz dos princípios da Análise da Conversação, se efetivamente ocorre uma conversação entre os participantes no ambiente de troca de mensagens dos blogs. Para a realização do estudo, foi compilado um corpus de 400 comentários cujo conteúdo demonstra a visão crítica de leitores dos blogs acima citados acerca de um mesmo tema: o apagão ocorrido em 10 de novembro de 2009 em 18 estados brasileiros. Tais mensagens foram trabalhadas a partir de um método predominantemente qualitativo e interpretativo, sendo que uma abordagem quantitativa também foi considerada para permitir uma visão mais abrangente e comparativa dos dados. Na ausência de um referencial teórico da Linguística que abrangesse os fenômenos interacionais percebidos nos comentários dos blogs, optou-se por desenvolver uma proposta de análise de base empírica, que norteou todo o desenvolvimento do trabalho. Entre as conclusões preliminares da pesquisa, pode-se dizer que, ao mesmo tempo em que os blogs inauguraram uma nova forma de relacionamento entre o jornalista e sua audiência, há indícios de grande parte dos leitores utilizem os blogs como um espaço restrito à publicação de opiniões isoladas, em vez de enxergá-lo como um ambiente com amplas possibilidades interativas, e, consequentemente, propício à discussão

Métodos de desacoplo de antenas PIFA en terminales móviles

[ES]Hoy en día, los sistemas de comunicación inalámbricos soportan un amplio número de servicios como la voz, datos y vídeos que requieren unas grandes tasas de transmisión. Por ello la mejora de la calidad del enlace que ofrecen los sistemas MIMO es clave. El problema surge al colocar varias antenas en un terminal móvil sin que aparezca un acoplamiento entre las distintas antenas que evite el correcto funcionamiento de estas. En este documento se realizará un estudio de los diferentes métodos de desacoplo entre antenas PIFA (Planar Inverted-F antenna) en un terminal móvil.