Wake instability issues: From circular cylinders to stalled airfoils

Some recent results regarding the global dynamical behaviour of the wake of circular cylinders and airfoils with massive separation are reviewed in this paper. In order to investigate the effect of interference, the three-dimensional instability modes are analysed for the flow around two circular cylinders in tandem. In the same way, the flow around a stalled airfoil is investigated in order to provide a better understanding of the three-dimensional characteristics of wakes forming downstream of a lifting body with massive separation. These results are compared with those found for an isolated cylinder. Some fundamental differences among these flows are discussed. (C) 2011 Elsevier Ltd. All rights reserved.

Panel Method Formulation for Oscillating Airfoils in Sonic Flow

The mathematical model for two-dimensional unsteady sonic flow, based on the classical diffusion equation with imaginary coefficient, is presented and discussed. The main purpose is to develop a rigorous formulation in order to bring into light the correspondence between the sonic, supersonic and subsonic panel method theory. Source and doublet integrals are obtained and Laplace transformation demonstrates that, in fact, the source integral is the solution of the doublet integral equation. It is shown that the doublet-only formulation reduces to a Volterra integral equation of the first kind and a numerical method is proposed in order to solve it. To the authors' knowledge this is the first reported solution to the unsteady sonic thin airfoil problem through the use of doublet singularities. Comparisons with the source-only formulation are shown for the problem of a flat plate in combined harmonic heaving and pitching motion.

Influence of structural nonlinearities in stall-induced aeroelastic response of pitching airfoils

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Characterization of grazing bifurcation in airfoils with control surface freeplay nonlinearity

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Aerodynamic study of airfoils geometric imperfections at low Reynolds number

The interest of this study is based on the observation that some manufacturing processes of various vehicles wings, such as unmanned aerial vehicle (UAV), or blades, such as wind turbine blades, or other devices that use aerodynamic profiles, produce imperfections in the leading edge or open trailing edge with bigger thickness than original airfoil, because, for example, they are manufactured in two parts, top surface and bottom surface and subsequently joined. In this last step might appear a sliding between the top surface and the bottom surface having a small step on the leading edge or a small thickness gain can occur on the trailing edge. Normally these imperfections are corrected through a refill and/or sanding processes using many hours of manual labor. Therefore the initial objective of this research is to determine the level of influence in the aerodynamic characteristics at low Reynolds numbers (Lissaman, 1981, Carmichael, 1981, Nagamatsu and Cuche, 1981, Schmitz, 1957, Cebeci, 1989, Mueller and Batill, 1982) of these imperfections in the manufacture, and determine whether there may be a value for which it would not be necessary to correct them

Aerodynamic Analysis of Open Trailing Edge Airfoils at Low Reynolds Number

A study has been made on the influence of the open trailing edge in airfoils used in different devices relating their aerodynamic performances. Wind tunnel tests have been made at different Reynolds numbers and angles of attack in order to show this effect. Besides, a quantitative study of the aerodynamic properties has been made based on the different trailing edge thickness

Aerodynamic Study of Airfoils with Leading Edge Imperfections at Low Reynolds Number

A study has been made on the influence of the leading edge imperfections in airfoils used in different devices relating their aerodynamic performances. Wind tunnel tests have been made at different Reynolds numbers and angle of attacks in order to show this effect. Later, a quantitative study of the aerodynamic properties has been made based on the different leading edge imperfections and their size.

Physics of Vibrating Airfoils at Low Reduced Frequency

The unsteady aerodynamics of low pressure turbine vibrating airfoils in flap mode is studied in detail using a frequency domain linearized Navier-Stokes solver. Both the travelling-wave and influence coefficient formulations of the problem are used to highlight key aspects of the physics and understand different trends such as the effect of reduced frequency and Mach number. The study is focused in the low-reduced frequency regime which is of paramount relevance for the design of aeronautical low-pressure turbines and compressors. It is concluded that the effect of the Mach number on the unsteady pressure phase can be neglected in first approximation and that the unsteadiness of the vibrating and adjacent airfoils is driven by vortex shedding mechanisms. Finally a simple model to estimate the work-per-cycle as a function of the reduced frequency and Mach Number is provided. The edge-wise and torsion modes are presented in less detail but it is shown that acoustic waves are essential to explain its behaviour. The non-dimensional work-per-cycle of the edge-wise mode shows a large dependence with the Mach number while in the torsion mode a large number of airfoils is needed to reconstruct the work-per-cycle departing from the influence coefficients.

On the circulation and the position of the forward stagnation point on airfoils

Lift and velocity circulation around airfoils are two aspects of the same phenomenon when airfoils are not stalled and the Kutta—Joukowski theorem applies. This theorem establishes a linear dependence between lift and circulation, which breaks when stalling occurs. As the angle of attack increases beyond this point, the circulation vanishes. Since the circulation determines to a great extent the position of the forward stagnation point on an airfoil, the measurement of this position is an easy and simple way to determine the circulation, which is of help in understanding the role of the latter in the generation of aerodynamic forces on airfoils.

Wind tunnel tests of thin airfoils oscillating near stall.

"January 1969."

Macro-Fiber Composite Actuators for Flow Control of a Variable Camber Airfoil

This research employs solid-state actuators for delay of flow separation seen in airfoils at low Reynolds numbers. The flow control technique investigated here is aimed for a variable camber airfoil that employs two active surfaces and a single four-bar (box) mechanism as the internal structure. To reduce separation, periodic excitation to the flow around the leading edge of the airfoil is induced by a total of nine piezocomposite actuated clamped-free unimorph benders distributed in the spanwise direction. An electromechanical model is employed to design an actuator capable of high deformations at the desired frequency for lift improvement at post-stall angles. The optimum spanwise distribution of excitation for increasing lift coefficient is identified experimentally in the wind tunnel. A 3D (non-uniform) excitation distribution achieved higher lift enhancement in the post-stall region with lower power consumption when compared to the 2D (uniform) excitation distribution. A lift coefficient increase of 18.4% is achieved with the identified non-uniform excitation mode at the bender resonance frequency of 125 Hz, the flow velocity of 5 m/s and at the reduced frequency of 3.78. The maximum lift (Clmax) is increased 5.2% from the baseline. The total power consumption of the flow control technique is 639 mW(RMS).

Piezoceramic Composite Actuators for Flow Control in Low Reynolds Number Airflow

The research presented here employs solid-state actuators for flow separation delay or for forced attachment of separated flow seen in airfoils at low Reynolds numbers. To reduce separation, periodic excitation to the flow around the leading edge of the airfoil is induced by Macro-Fiber Composite actuated clamped-free unimorph benders. An electromechanical model of the unimorph is briefly presented and parametric study is conducted to aid the design of a unimorph to output high deformation at a desired frequency. The optimum frequency and amplitude for lift improvement at post-stall angles are identified experimentally. Along with aerodynamic force and structural displacement measurements, helium bubble flow visualization is used to verify existing separated flow, and the attached flow induced by flow control. The lift enhancement induced by several flow control techniques is compared. A symmetric and non-uniform (3D) flow excitation results in the maximum lift enhancement at post-stall region at the lowest power consumption level. A maximum lift coefficient increase of 27.5% (in the post-stall region) is achieved at 125 Hz periodic excitation, with the 3D symmetric actuation mode at 5 m/s and the reduced frequency of 3.78. C(l,max) is increased 7.6% from the baseline.

Inverse aerodynamic design applications using the MGM hybrid formulation

The well-known modified Garabedian-Mcfadden (MGM) method is an attractive alternative for aerodynamic inverse design, for its simplicity and effectiveness (P. Garabedian and G. Mcfadden, Design of supercritical swept wings, AIAA J. 20(3) (1982), 289-291; J.B. Malone, J. Vadyak, and L.N. Sankar, Inverse aerodynamic design method for aircraft components, J. Aircraft 24(2) (1987), 8-9; Santos, A hybrid optimization method for aerodynamic design of lifting surfaces, PhD Thesis, Georgia Institute of Technology, 1993). Owing to these characteristics, the method has been the subject of several authors over the years (G.S. Dulikravich and D.P. Baker, Aerodynamic shape inverse design using a Fourier series method, in AIAA paper 99-0185, AIAA Aerospace Sciences Meeting, Reno, NV, January 1999; D.H. Silva and L.N. Sankar, An inverse method for the design of transonic wings, in 1992 Aerospace Design Conference, No. 92-1025 in proceedings, AIAA, Irvine, CA, February 1992, 1-11; W. Bartelheimer, An Improved Integral Equation Method for the Design of Transonic Airfoils and Wings, AIAA Inc., 1995). More recently, a hybrid formulation and a multi-point algorithm were developed on the basis of the original MGM. This article discusses applications of those latest developments for airfoil and wing design. The test cases focus on wing-body aerodynamic interference and shock wave removal applications. The DLR-F6 geometry is picked as the baseline for the analysis.

Concepção de uma pequena turbina eólica destinada ao segmento doméstico (simplificação e análise aerodinâmica das pás)

O trabalho que se apresenta incide sobre o estudo aerodinâmico das pás de uma turbina eólica de pequeno porte, com vista à simplificação geométrica, de forma a que estas sejam baratas e de fácil concepção. A teoria da quantidade de movimento do elemento de pá (BEMT), que é o modelo de referência para o projecto e análise aerodinâmica das pás das turbinas eólicas, foi utilizada neste trabalho de forma a projectar e analisar aerodinamicamente as pás da turbina. Sendo assim, desenvolveu-se um programa computacional em MATLAB, denominado de “Turbina”, de forma a implementar a teoria BEM. Introduzindo os dados dos parâmetros de projecto no programa (potência requerida, o número de pás, velocidade do vento, a TSR e o tipo de perfil alar), obtêm-se os parâmetros geométricos das pás (distribuição da corda ao longo da envergadura, o raio da pá e a distribuição da torção da pá), os parâmetros aerodinâmicos e de desempenho. Uma pá ideal foi calculada e de seguida foi modificada de forma a obter-se uma pá simples e menos carregada aerodinamicamente. Introduzidas as modificações na geometria da pá ideal, obtiveram-se duas configurações distintas. Uma configuração linear, onde a distribuição da corda e do ângulo de torção se tornam lineares, e outra configuração bi-linear, onde a distribuição da corda continua linear mas o ângulo de torção se torna bi-linear, isto é, a pá é composta por dois troços onde cada troço apresenta uma distribuição linear do ângulo de torção geométrica. As conclusões demonstram que a configuração bi-linear é uma boa alternativa a configuração ideal, apresentando uma redução do desempenho do rotor de 2.8% para um aumento do raio da pá em 1.41%, para se obter a mesma potência da configuração ideal. A análise aos perfis alares, utilizados neste trabalho, foi efectuada a partir dos programas comerciais ICEM e FLUENT. De forma a automatizar a análise de CFD, três programas foram desenvolvidos utilizando a linguagem de programação “C”. Os programas são denominados de “Malha2D”, “Calcula_Coeficientes” e “Plot_Graficos”. Finalmente, um estudo paramétrico foi feito de forma a avaliar a influências das variáveis de projecto no desempenho geral da turbina.

Techniques for Enhancing Wind Energy Generation - A CFD Based Multibody Dynamics Approach in Horizontal Axis Wind Turbines

Wind energy has emerged as a major sustainable source of energy.The efficiency of wind power generation by wind mills has improved a lot during the last three decades.There is still further scope for maximising the conversion of wind energy into mechanical energy.In this context,the wind turbine rotor dynamics has great significance.The present work aims at a comprehensive study of the Horizontal Axis Wind Turbine (HAWT) aerodynamics by numerically solving the fluid dynamic equations with the help of a finite-volume Navier-Stokes CFD solver.As a more general goal,the study aims at providing the capabilities of modern numerical techniques for the complex fluid dynamic problems of HAWT.The main purpose is hence to maximize the physics of power extraction by wind turbines.This research demonstrates the potential of an incompressible Navier-Stokes CFD method for the aerodynamic power performance analysis of horizontal axis wind turbine.The National Renewable Energy Laboratory USA-NREL (Technical Report NREL/Cp-500-28589) had carried out an experimental work aimed at the real time performance prediction of horizontal axis wind turbine.In addition to a comparison between the results reported by NREL made and CFD simulations,comparisons are made for the local flow angle at several stations ahead of the wind turbine blades.The comparison has shown that fairly good predictions can be made for pressure distribution and torque.Subsequently, the wind-field effects on the blade aerodynamics,as well as the blade/tower interaction,were investigated.The selected case corresponded to a 12.5 m/s up-wind HAWT at zero degree of yaw angle and a rotational speed of 25 rpm.The results obtained suggest that the present can cope well with the flows encountered around wind turbines.The areodynamic performance of the turbine and the flow details near and off the turbine blades and tower can be analysed using theses results.The aerodynamic performance of airfoils differs from one another.The performance mainly depends on co-efficient of performnace,co-efficient of lift,co-efficient of drag, velocity of fluid and angle of attack.This study shows that the velocity is not constant for all angles of attack of different airfoils.The performance parameters are calculated analytically and are compared with the standardized performance tests.For different angles of ,the velocity stall is determined for the better performance of a system with respect to velocity.The research addresses the effect of surface roughness factor on the blade surface at various sections.The numerical results were found to be in agreement with the experimental data.A relative advantage of the theoretical aerofoil design method is that it allows many different concepts to be explored economically.Such efforts are generally impractical in wind tunnels because of time and money constraints.Thus, the need for a theoretical aerofoil design method is threefold:first for the design of aerofoil that fall outside the range of applicability of existing calalogs:second,for the design of aerofoil that more exactly match the requirements of the intended application:and third,for the economic exploration of many aerofoil concepts.From the results obtained for the different aerofoils,the velocity is not constant for all angles of attack.The results obtained for the aerofoil mainly depend on angle of attack and velocity.The vortex generator technique was meticulously studies with the formulation of the specification for the right angle shaped vortex generators-VG.The results were validated in accordance with the primary analysis phase.The results were found to be in good agreement with the power curve.The introduction of correct size VGs at appropriate locations over the blades of the selected HAWT was found to increase the power generation by about 4%