Investigation of air quality, comfort parameters and effectiveness for two floor-level air supply systems in classrooms

The method of distributing the outdoor air in classrooms has a major impact on indoor air quality and thermal comfort of pupils. In a previous study, ([11] Karimipanah T, Sandberg M, Awbi HB. A comparative study of different air distribution systems in a classroom. In: Proceedings of Roomvent 2000, vol. II, Reading, UK, 2000. p. 1013-18; [13] Karimipanah T, Sandberg M, Awbi HB, Blomqvist C. Effectiveness of confluent jets ventilation system for classrooms. In: Idoor Air 2005, Beijing, China, 2005 (to be presented).) presented results for four and two types of air distribution systems tested in a purpose built classroom with simulated occupancy as well as computational fluid dynamics (CFD) modelling. In this paper, the same experimental setup has been used to investigate the indoor environment in the classroom using confluent jet ventilation, see also ([12]Cho YJ, Awbi HB, Karimipanah T. The characteristics of wall confluent jets for ventilated enclosures. In: Proceedings of Roomvent 2004, Coimbra, Portugal, 2004.) Measurements of air speed, air temperature and tracer gas concentrations have been carried out for different thermal conditions. In addition, 56 cases of CFD simulations have been carried to provide additional information on the indoor air quality and comfort conditions throughout the classroom, such as ventilation effectiveness, air exchange effectiveness, effect of flow rate, effect of radiation, effect of supply temperature, etc., and these are compared with measured data.

Gas flow analysis in a Kraft recovery boiler

Demands for optimal boiler performance and increased concerns in lowering emission have always been the driving force in the reevaluation and evolution of the Kraft boiler: specifically the air distribution strategies that are directly related to achieving increased residence time of flue gas combustion inside the furnace which in turn lowers atmosphere emission levels and enhances boiler operation. This paper presents the results of a study that analyzes the interaction of the different multilevel air injections have on flue gas flow patterns including various quaternary air supply arrangements. Additionally, this study assesses the performance of the CFD (Computational Fluid Dynamics) model against data available in literature. Simulations were performed considering isothermal and incompressible flows, and did not take into account thermal phenomena or chemical reactions. The numerical solutions generated proved to be coherently related to the data available in literature, and provided proof of the efficiency of tertiary level air injection, as well as revealed that quaternary air injection ports arranged in a symmetrical configuration is most suitable for optimal equipment operation. (C) 2010 Elsevier B.V. All rights reserved.

Air uptake along the lower nappe of a spillway aerator

Air concentration measurements performed along the lower nappe of a bottom aerator through the impact and downstream flow regions permitted the calculation of air entrainment along the jet length. The air uptake was also measured in the air supply conduit. It was shown that integration of the concentration profiles along the jet overestimates the air uptake measured in the air supply conduit. Corrective procedures were developed by adapting the concept of entrained and entrapped air, in which the latter is re-circulated in the cavity, but both are measured by air concentration probes.

The air distribution index as an indicator for energy consumption and performance of ventilation systems

This paper deals with the energy consumption and the evaluation of the performance of air supply systems for a ventilated room involving high- and low-level supplies. The energy performance assessment is based on the airflow rate, which is related to the fan power consumption by achieving the same environmental quality performance for each case. Four different ventilation systems are considered: wall displacement ventilation, confluent jets ventilation, impinging jet ventilation and a high level mixing ventilation system. The ventilation performance of these systems will be examined by means of achieving the same Air Distribution Index (ADI) for different cases. The widely used high-level supplies require much more fan power than those for low-level supplies for achieving the same value of ADI. In addition, the supply velocity, hence the supply dynamic pressure, for a high-level supply is much larger than for low-level supplies. This further increases the power consumption for high-level supply systems. The paper considers these factors and attempts to provide some guidelines on the difference in the energy consumption associated with high and low level air supply systems. This will be useful information for designers and to the authors' knowledge there is a lack of information available in the literature on this area of room air distribution. The energy performance of the above-mentioned ventilation systems has been evaluated on the basis of the fan power consumed which is related to the airflow rate required to provide equivalent indoor environment. The Air Distribution Index (ADI) is used to evaluate the indoor environment produced in the room by the ventilation strategy being used. The results reveal that mixing ventilation requires the highest fan power and the confluent jets ventilation needs the lowest fan power in order to achieve nearly the same value of ADI.

Analysis of Direct Outdoor Air Cooling Efficency for Combined Variable Air Volume Air-conditioning System in Stores in Cold Climates of China

Direct outdoor air cooling contributes a lot not only to the improvement of the indoor air quality but also to the energy saving. Its full use will reduce the water chiller’s running time especially in some stores where cooling load keeps much higher and longer than that in other buildings. A novel air-conditioning system named Combined Variable Air Volume system (CVAV), combining a normal AHU with a separate outdoor air supply system, was proposed firstly by the authors. The most attractive feature of the system is its full utilization of cooling capacity and freshness of outdoor air in the transition period of the year round. On the basis of the obtain of the dynamic cooling loads of the typical shopping malls in different four cities located in cold climates in China with the aid of DOE-2, the possibility of increasing the amount of outdoor air volume of CVAV system in the transition period instead of operating the water chillers was confirmed. Moreover, a new concept, Direct Outdoor Air Cooling Efficiency (DOACE), was defined as the ratio of cooling capacity of outdoor air to the water chiller, indicating the degree of outdoor air’s utilization. And the DOACE of the CVAV was calculated and compared with that of conventional all-air constant volume air-conditioning systems, the results showed that CVAV bear much more energy saving potential with the 10%~19% higher DOACE and it is a kind of energy efficient systems and can improve the indoor air quality as well.

Experimental study on the impact of using a fan coil in the evaluation of contaminant removal effectiveness of common air diffusion strategies

Indoor Air 2016 - The 14th International Conference Indoor Air Quality and Climate

The Use of Cryogenic Air in Supplied Air Respiratory Protection

The Mine Improvement and New Emergency Response (MINER) Act of 2006 implemented new regulations in the underground coal mining industry that allow for the certification of non-compressed gas equipment for respiratory protection in underground coal mines. NASA’s Kennedy Space Center (KSC) Biomedical Research and Engineering Laboratory (BRL) is investigating the potential to expand cryogenic air supply systems into the mining and general industries. These investigations have, so far, resulted in four separate comparison and hardware development programs. The Propellant Handlers Ensemble (PHE) and Level “A” Ensemble Comparison (LAE): This study compared worker thermal stress while using the industry standard Level A hazardous material handling ensemble as opposed to using the similarly protective Propellant Handler’s Ensemble (PHE) that utilizes a cryogenic air supply pack, known as an Environmental Control Unit (ECU) as opposed to the compressed air Self Contained Breathing Apparatus (SCBA) used in the LAE. The research found that, in a 102°F environment, test subjects experienced significantly decreased body temperature increases, significantly decreased heart rate increases, and decreased sweat loss while performing a standard work routine while using the PHE, compared to the same test subjects performing the same routine while using the LAE. The Cryogenic Refuge Alternative Supply System (CryoRASS) project: The MINER Act of 2006 requires the operators of underground coal mines to provide refuge alternatives that can provide a safe atmosphere for workers for up to 96 hours in the event of a mine emergency. The CryoRASS project retrofitted an existing refuge chamber with a liquid air supply instead of the standard compressed air supply system and performed a 96 hour test. The CryoRASS system demonstrated that it provided a larger air supply in a significantly smaller footprint area, provided humidity and temperature control, and maintained acceptable oxygen and carbon dioxide levels in the chamber for the required amount of time. SCBA and Mine Rescue System (CryoBA/CryoASFS) Another requirement of the MINER Act is that additional emergency breathing equipment must be staged along evacuation routes to supplement the Self Contained/Self Rescue (SCSR) devices that are now required. The BRL has developed an SCBA known as the Cryogenic Breathing Apparatus (CryoBA), that has the ability to provide 2 hours of breathing air, a refill capability, and some cooling for the user. Cryogenic Air Storage and Filling Stations (CryoASFS) would be positioned in critical areas to extend evacuation time. The CryoASFS stations have a significantly smaller footprint and larger air storage capacity to similar compressed air systems. The CryoBA pack is currently undergoing NIOSH certification testing. Technical challenges associated with liquid breathing air systems: Research done by the BRL has also addressed three major technical challenges involved with the widespread use of liquid breathing air. The BRL developed a storage Dewar fitted with a Cryorefrigerator that has stored liquid air for four months with no appreciable oxygen enrichment due to differential evaporation. Testing of liquid breathing air was material and time intensive. A BRL contract developed a system that only required 1 liter of air and five minutes of time compared to the 10 liters of air and 75 minutes of time required by the old method. The BRL also developed a simple and cost effective method of manufacturing liquid air that joins a liquid oxygen tanker with a liquid nitrogen tanker through an orifice controlled “Y” fitting, mixing the two components, and depositing the mixed breathing air in a separate tanker.

Projecto integrado de AVAC e outras especialidades para um edifício com necessidades quase nulas de energia

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica

Acompanhamento do Processo de Compostagem e Identificação de Hipóteses de Melhoria, Tendo em Vista a Valorização do Produto Comercializado

A compostagem tem-se revelado uma boa alternativa na gestão, tratamento e valorização de resíduos sólidos urbanos. Dependendo das matérias-primas usadas no processo, os produtos podem ser considerados fertilizantes/corretivos orgânicos com utilidade agrícola. A Suldouro, Valorização e Tratamento de Resíduos Sólidos Urbanos, S.A., é responsável pela gestão, valorização, recuperação e destino final dos Resíduos Sólidos Urbanos (RSU) produzidos em Vila Nova de Gaia e Santa Maria da Feira. Um dos processos do sistema de gestão é a valorização orgânica, que através da compostagem dos resíduos biodegradáveis origina um corretivo orgânico, denominado comercialmente de Agrovida. O objetivo deste trabalho foi caracterizar o composto produzido na Suldouro através da análise de alguns metais, nomeadamente cobre, zinco e chumbo, pois o seu teor condiciona a classe em que o composto está inserido, e da avaliação da razão C/N, visto ser um parâmetro importante para o desenvolvimento dos microrganismos. Um outro objetivo foi a determinação do tempo ótimo de compostagem, através da avaliação da temperatura máxima, recorrendo ao teste de auto-aquecimento usando vasos de Dewar. O estudo da presença de chumbo não chegou a ser realizado, pois a sua concentração era muito baixa (da ordem dos ppb), ou seja, não era limitativa para a utilização do composto. Quanto à análise de cobre e zinco no composto verificou-se que era necessário fazer alterações no processo, no sentido de reduzir estes valores, tanto a nível da qualidade dos resíduos usados como matéria-prima como a nível da limpeza, essencial depois das operações de manutenção aos pulpers. Em relação à razão C/N esta apresenta valores muito elevados, ou seja, uma quantidade de azoto total muito baixa, indicativa de que seria necessário acrescentar, no início do processo, resíduos mais ricos em azoto. A análise do teste de auto-aquecimento indica que o tempo necessário para a estabilização e maturação das pilhas de compostagem é superior a 3 meses. Assim, sugerem-se melhorias a nível da qualidade do resíduo, tentando incluir resíduos mais facilmente biodegradáveis, uma redução da altura da pilha proporcionando um melhor arejamento ou em alternativa proceder periodicamente ao seu revolvimento como complemento à insuflação de ar. Para concluir, neste trabalho foi realizada uma pesquisa sobre processos de valorização energética, alternativas potenciais à valorização orgânica, tendo sido dado especial relevo a um dos processos, a carbonização hidrotérmica (HTC).

Exposição a ozono em cabinas de avião

RESUMO - O ozono é o principal componente da poluição fotoquímica do ar. Como agente irritante do aparelho respiratório, os seus efeitos sobre a saúde caracterizam-se, essencialmente, por tosse, dispneia, desconforto torácico e alterações da função pulmonar, encontrando-se também associadas à exposição ambiental a O3 tanto uma maior frequência e gravidade de crises de asma como a ocorrência de quadros clínicos de irritação conjuntival. É sobretudo a partir dos anos 50, com a descoberta de concentrações elevadas de ozono em ambientes de trabalho respeitantes à actividade de soldadura «a arco», que aquele gás passa a ser encarado como factor profissional de risco. No início dos anos 60 surgem os primeiros estudos de exposição a O3 em cabinas de avião, suscitados pela ocorrência, em tripulantes e passageiros, de queixas clínicas de irritação do tracto respiratório. Esta sintomatologia era, até então, atribuída à acção de outros factores, designadamente o sistema de ventilação e o baixo teor de humidade do ar. Posteriormente, alguns estudos revelaram que, em voos comerciais subsónicos, os teores elevados de O3 observados no interior das cabinas poderiam ser provocados pela sua insuficiente destruição nos sistemas de entrada de ar.O presente estudo, efectuado em voos de longo curso realizados em aeronaves Airbus A340-300 numa única rota comercial, teve por objectivo avaliar a exposição a ozono no ar interior em cabina de avião. Os teores médios de concentração de ozono observados foram inferiores aos valores susceptíveis de provocarem efeitos adversos sobre o aparelho respiratório. Como valor máximo instantâneo, foi atingida a concentração de 152 ppb. Adicionalmente, foi constatada a influência das estações do ano nos teores de O3. O conjunto dos resultados obtidos permite concluir que as concentrações de ozono no ar interior nas cabinas de avião estudadas são inferiores às correspondentes concentrações máximas admissíveis, tendo, em todos os voos, sido observado o cumprimento da norma da FAA respeitante à protecção da exposição ao ozono em cabinas de aeronaves de aviação comercial.

Paineilmajärjestelmän ja -hankinnan kehittäminen sementtitehtaalla

Työn tavoitteena oli kartoittaa Lappeenrannan sementtitehtaan paineilmajärjestelmä, tehdä järjestelmän kehittämissuunnitelma ja arvioida suunnitelman mukaisen investoinnin kannattavuus investointilaskelmilla. Kartoituksesta selviää paineilman hankinnan toteutus, järjestelmään kuuluvien laitteiden selvitys ja energiankulutus sekä jakeluverkon ja paineilman käytön kartoitus. Kartoituksen ja aineiston pohjalta laadittiin suunnitelma järjestelmän kehittämiseksi. Aineistoa kerättiin haastattelemalla laitetoimittajia sekä muiden sementtitehtaiden johtoa. Paineilman käyttöä tehostettiin ja tehtaan matalapaine- eli kuumailmaverkon osalta tehtiin suunnitelmat sen täydellisestä uusimisesta. Tehtaan korkeapaine- eli yleisilmaverkkoon päätettiin olla investoimatta työssä esiteltävien käytännön syiden vuoksi. Investoinnin taloudellinen kannattavuus arvioitiin työhön rakennetulla investointilaskentamallilla. Sen avulla laskettiin investoinnin kannattavuus annuiteettimenetelmällä. Laskelmien tulokseen liittyvä epävarmuus arvioitiin myös malliin rakennetulla herkkyysanalyysillä. Lisäksi mallilla vertailtiin investoinnin eri hankintavaihtoehtojen kannattavuutta. Investointi osoittautui kannattavaksi.

Kerrosleijukattilan sekundääri-ilmansyöttöjärjestelmän kehittäminen

Työn tarkoituksena oli kehittää kerrosleijukattilan sekundääri-ilmansyöttöä. Työssä tutkittiin tulipesässä ilmasuihkujen käyttäytymiseen vaikuttavia tekijöitä sekä eri ilmansyöttömallien vaikutuksia tulipesäolosuhteisiin. Sekundääri- ja tertiääri-ilmasuihkujen tehtävänä on sekoittaa tulipesän kaasuja sekä tuoda happi leijupetin yläpuolelle haihtuneiden aineiden palamisen loppuun saattamiseksi. Kaasujen sekoittumiseen vaikuttavat ilmasuihkun ja ristivirtauksen liikemäärien suhde, suutinten koko ja sijoittelu toisiinsa nähden. Ilmasuihku saavuttaa paremman tunkeutuvuuden ja siten tehokkaamman sekoittumisen suuttimen koon kasvaessa. Lisäksi tunkeutuvuus paranee suutinten välisen etäisyyden sekä ilmasuihkun ja ristivirtauksen liikemäärien suhteen kasvaessa. Optimaalisen suutinten välisen etäisyyden osoitettiin riippuvan suuttimen ja tulipesän koosta sekä ilmasuihkun ja ristivirtauksen liikemäärien suhteesta. Saatujen tulosten mukaan sekundääri- ja tertiääri-ilmatasoilla tulee suosia suuria harvaan ja lomittain sijoitettuja suuttimia. Ilmansyöttömalleja tutkittiin numeerisesti mallintamalla, ja saatujen tulosten perusteella tehokkain sekoittuminen saavutettiin sijoittamalla sekundääri-ilmasuuttimet tulipesän kahdelle vastakkaiselle seinälle.

Korkeasti kuormitetun soodakattilan likaantumisen ja päästöjen vähentäminen

Tässä työssä perehdytään korkeasti kuormitettujen soodakattiloiden tyypillisiin ongelmiin. Ongelmia ovat likaantuminen ja tukkeutuminen sekä liialliset päästöt. Työn teoriaosassa esitetään taustat likaantumiselle ja päästöjen muodostumiselle. Molemmat johtuvat suurelta osin tulipesän huonosta toiminnasta. Soodakattilan ilmajärjestelmä ja mustalipeän ruiskutus vaikuttavat tulipesän toimintaan. Usein tulipesän toimintaa voidaan parantaa ilmajärjestelmän ja lipeänruiskutuksen säätöjä muuttamalla. Suurempi muutos tulipesän toimintaan saadaan uusimalla perinteinen sekundääri-ilmajärjestelmä vertikaali-ilmajärjestelmäksi. Nykyaikainen vertikaali-ilmajärjestelmä sekoittaa savukaasut tehokkaasti ja saa aikaan tasaisemman virtauksen tulipesään. Myös mustalipeän korkea kloori- ja kaliumpitoisuus voivat aiheuttaa lämpöpintojen likaantumista. Oikea nuohointen sijainti on tärkeä tekijä kattilan puhtaana pysymisen kannalta. Työn kokeellisessa osassa selvitetään, kuinka erään eukalyptussellutehtaan korkeasti kuormitetun soodakattilan käytettävyyttä voidaan parantaa ja kapasiteettia nostaa soodakattilan toimintaa virittämällä. Kattilan nykyinen ajomalli ja ongelmat selvitettiin. Tulipesän toimintaa testattiin muuttamalla ilmajakoa primääri-, sekundääri- ja tertiääri-ilman välillä ja muuttamalla sekundääri-ilman syöttöä tulipesään. Testien ja kerätyn tiedon perusteella voitiin päätellä, miten soodakattilaa kannattaa modernisoida kapasiteetin nostamiseksi ja käytettävyyden parantamiseksi. Usein tulipesän toimintaa ja käytettävyyttä voidaan parantaa paljon jo pienilläkin muutostöillä. Kapasiteetin nostaminen vaatii tavallisesti suuremman investoinnin ja pidennetyn vuosihuoltoseisokin.

L-histidine enhances learning in stressed zebrafish

The aim of the present study was to determine the effect of the histaminergic precursor L-histidine and the H3 receptor antagonist thioperamide on the learning process of zebrafish submitted or not to confinement stress. On each of the 5 consecutive days of experiment (D1, D2, D3, D4, D5), animals had to associate an interruption of the aquarium air supply with food offering. Non-stressed zebrafish received an intraperitoneal injection of 100 mg/kg L-histidine, 10 mg/kg thioperamide or saline after training. Stressed animals received drug treatment and then were submitted to confinement stress for 1 h before the learning procedure. Time to approach the feeder was measured (in seconds) and was considered to be indicative of learning. A decrease in time to approach the feeder was observed in the saline-treated group (D1 = 141.92 ± 13.57; D3 = 55 ± 13.54), indicating learning. A delay in learning of stressed animals treated with saline was observed (D1 = 217.5 ± 25.66). L-histidine facilitated learning in stressed (D1 = 118.68 ± 13.9; D2 = 45.88 ± 8.2) and non-stressed (D1 = 151.11 ± 19.20; D5 = 62 ± 14.68) animals. Thioperamide inhibited learning in non-stressed (D1 = 110.38 ± 9.49; D4 = 58.79 ± 16.83) and stressed animals (D1 = 167.3 ± 26.39; D5 = 172.15 ± 27.35). L-histidine prevented the increase in blood glucose after one session of confinement (L-histidine = 65.88 ± 4.50; control = 53 ± 3.50 mg/dL). These results suggest that the histaminergic system enhances learning and modulates stress responses in zebrafish.

Rights of the Prisoner: An Evolving Jurisprudence

Imprisonment is the most common method of punishment resorted to by almost all legal systems.The new theories of crime causation propounded in the latter half of the nineteenth century gave rise to the feeling that the prisons could be used as appropriate institutions for reforming the offenders. It called for individualisation of punishment.As a result of international movements for humanisation of prisons the judiciary' in tine common law countries started taking active interest in prisoner's treatment.Various studies reveal that much has been done in America to improve the lot of prisoners and to treat them as human beings.The courts there have gone to the extent of saying that there is no iron curtain between a prisoner and the constitution. Most of the rights available to citizens except those which they cannot enjoy due to the conditions of incarceration have also been granted to prisoner.In India also the judiciary has come forward to protect the rights of the prisoners.Maneka Gandhi is a turning point in prisoner's rights.The repeated intervention of courts in prison administration project the view that prisoners have been denied the basic human rights.The High Courts and the Supreme Court of India have been gradually exercising jurisdiction ixl assuming prison justice, including improving the quality of food and amenities, payment of wages and appropriate standards of medical care. Access to courts must be made easier to the aggrieved prisoners.The government should come forward along with some public spirited citizens and voluntary organisations to form a "discharged prisoner“ aid society. The society should exploit opportunities for rehabilitation of prisoners after their release.Most of the prison buildings in the State of Kerala are ill-equipped, ill furnished and without proper ventilation or sanitation and with insufficient water supply arrangements.In India prisoners and prisons today are governed by the old central legislations like Prisons Act l894 Prisoners Act 1900 and the Transfer of Prisoners Act 1950.