Structural changes induced by ultrasound during aging of the boehmite phase

Structural changes induced by ultrasound during the aging of the aluminum monohydroxide (boehmite) were studied by means of X-ray diffraction (XRD) and nitrogen adsorption. The BET surface area and the pore volume of the ultrasound stimulated hydroxide (HU) are about 40% less than those of the non-stimulated one (HS). The mean pore size practically does not change, while the mean crystallite size (L) is about 25% greater in the HU system. The increase of L alone is not enough to account for the surface area diminution, suggesting that the sonication also induces compaction by elimination of some porosity. The sonication of the precursor hydroxide does not seem to play an apparent role in the structural properties of the resulting calcinated γ-alumina. © 1997 Elsevier Science B.V.

Consumers' emotional judgement of materials durability and disposal

The literature demonstrates that understanding relating to the use of materials in product design has been investigated from both engineering and design perspectives. However, none of these studies have explored the consumers’ concepts of the materials; rather they have focused on participants’ discussions of material samples. Consumers’ emotional reactions to the materials themselves or the consumers’ reaction to the durability of the materials have not been previously explored in depth. This research has investigated these issues and has found that consumers have very specific concepts about materials. Furthermore, the combinations of consumer concepts that are likely to elicit an emotional judgement by the consumer have also been identified. It was found that consumers are conscious of the durability of their products and the materials that they are made from. This knowledge contributes to the support of environmentally conscious design, as well as user-centered design knowledge and practice. An understanding of the emotion consumers attribute to the effect wear and aging had on the materials’ physical appearance has been achieved. This understanding of consumers’ emotional reactions to materials can contribute not only to design considerations but to knowledge regarding the promotion of prolonged product-user relationships.

The effect of preaging on the delayed aging of Al-7Si-0.3Mg

Al-7Si-0.3Mg is a commonly used commercial casting alloy because of its excellent castability combined with good mechanical properties. The post-casting heat treatment is one factor that affects the mechanical properties; during heat treat ment, a delay between solutionizing and artificial aging (delayed aging) leads to a reduction in hardness, ultimate tensile strength, and yield strength in the alloy. The investigation reported here was aimed at understanding the extent to which the harmful effect of delayed aging on hardness/strength can be nullified. The results obtained were explained using Pashley's kinetic model.

Accelerated multistress aging of polymer nanocomposites and its condition monitoring

In recent years, the time dependant maintenance of expensive high voltage power equipments is getting replaced by condition based maintenance so as to detect apriori an impending failure of the equipment. For condition based maintenance, most monitoring systems concentrate on the electrical quantities such as measurement and evaluation of partial discharges, tan delta, tip-up test, dielectric strength, insulation resistance, polarization and depolarization current. However, in the case of equipments being developed with novel nanodielectric insulating materials, the variation in these parameters before an impending failure is not available. Hence in this work, accelerated electrothermal aging studies have been conducted on unfilled epoxy as well as epoxy nanocomposite samples of 5 wt% filler loading, and the tan d values were continuously monitored to obtain the condition of the samples under study. It was observed that those samples whose tan d increased at a rapid rate failed first.

Accelerated aging of thick glass second surface silvered reflectors under sandstorm conditions

Concentrated solar power systems are expected to be sited in desert locations where the direct normal irradiation is above 1800 kWh/m2.year. These systems include large solar collector assemblies, which account for a significant share of the investment cost. Solarreflectors are the main components of these solar collector assemblies and dust/sand storms may affect their reflectance properties, either by soiling or by surface abrasion. While soiling can be reverted by cleaning, surface abrasion is a non reversible degradation.The aim of this project was to study the accelerated aging of second surface silvered thickglass solar reflectors under simulated sandstorm conditions and develop a multi-parametric model which relates the specular reflectance loss to dust/sand storm parameters: wind velocity, dust concentration and time of exposure. This project focused on the degradation caused by surface abrasion.Sandstorm conditions were simulated in a prototype environmental test chamber. Material samples (6cm x 6cm) were exposed to Arizona coarse test dust. The dust stream impactedthese material samples at a perpendicular angle. Both wind velocity and dust concentrationwere maintained at a stable level for each accelerated aging test. The total exposure time in the test chamber was limited to 1 hour. Each accelerated aging test was interrupted every 4 minutes to measure the specular reflectance of the material sample after cleaning.The accelerated aging test campaign had to be aborted prematurely due to a contamination of the dust concentration sensor. A robust multi-parametric degradation model could thus not be derived. The experimental data showed that the specular reflectance loss decreasedeither linearly or exponentially with exposure time, so that a degradation rate could be defined as a single modeling parameter. A correlation should be derived to relate this degradation rate to control parameters such as wind velocity and dust/sand concentration.The sandstorm chamber design would have to be updated before performing further accelerated aging test campaigns. The design upgrade should improve both the reliability of the test equipment and the repeatability of accelerated aging tests. An outdoor exposure test campaign should be launched in deserts to learn more about the intensity, frequencyand duration of dust/sand storms. This campaign would also serve to correlate the results of outdoor exposure tests with accelerated exposure tests in order to develop a robust service lifetime prediction model for different types of solar reflector materials.

Visual evaluation of color stability after accelerated aging of pigmented and nonpigmented silicones to be used in facial prostheses

Objectives: The objective of this study was to evaluate by a visual method of comparison the color stability of nonpigmented and pigmented facial silicones after accelerated aging. Materials and Methods: Two kinds of silicones were used in this study; one specifically formulated for facial prostheses and the other an acetic silicone for industrial use. Twenty-four trial bodies were made for each silicone. These were divided into colorless and intrinsically pigmented groups: ceramic, make-up, and iron oxide. The groups were submitted to accelerated aging for nonmetallic materials. An initial reading and subsequent readings were made at 163, 351, 692, and 1000 hours using a visual method of comparison. The values were annotated in a spreadsheet by two observers, according to scores elaborated for this study. Results: All groups presented color stability in the visual method. According to the results obtained and analyzed in this study, we can conclude that both silicones, Silastic 732 RTV and Silastic MDX 4-4210, behaved similarly, they can therefore be indicated for use in maxillofacial prosthesis. The time factor of aging influenced negatively, independently of the pigmentation, or lack of it, and of silicones and no group had visually noticeable alterations in any of the accelerated aging time, independently of the addition or not of pigments.

Color stability after accelerated aging of two silicones, pigmented or not, for use in facial prostheses

One of the greatest challenges faced by buccomaxillofacial prosthetists is to reproduce the patient's exact skin color and provide adequate esthetics. To reach this objective, professionals must use materials with easy characterization and that maintain color over long periods of time. The objective of this study was, thus, to evaluate the color stability of two types of silicones, Silastic 732 and Silastic MDX4-4210. Twenty-four test specimens were made from each type of silicone and were divided into a colorless group and groups intrinsically pigmented with ceramics, cosmetics or iron oxide. The specimens were submitted to an accelerated system of aging for non-metallic materials. Readings were carried out initially and after periods corresponding to 163, 351, 692 and 1,000 hours of aging, using a reflection spectrophotometer analysis, and color alterations were calculated by the CIE L*a*b* system. The data were submitted to variance analysis and Tukey's test at a 5% level of probability. The results demonstrated that, irrespective of the period of time analyzed, all the materials underwent some type of chromatic alteration (ΔE > 0). The test specimens made with Silastic 732 and MDX4-4210, without pigmentation, presented the lowest color alteration values after 1,000 hours of aging. Of the pigments, ceramic presented the lowest color alteration values and cosmetic powder presented the highest values. Thus, it may be concluded that the materials without the incorporation of pigments presented similar color alteration values, and did not differ statistically. The cosmetic powder used in this study was the pigment that most altered the color of the test specimens. © 2009 Sociedade Brasileira de Pesquisa Odontológica.

Aging of nuclear power plant cables: in search of non-destructive diagnostic quantities

The safety systems of nuclear power plants rely on low-voltage power, instrumentation and control cables. Inside the containment area, cables operate in harsh environments, characterized by relatively high temperature and gamma-irradiation. As these cables are related to fundamental safety systems, they must be able to withstand unexpected accident conditions and, therefore, their condition assessment is of utmost importance as plants age and lifetime extensions are required. Nowadays, the integrity and functionality of these cables are monitored mainly through destructive test which requires specific laboratory. The investigation of electrical aging markers which can provide information about the state of the cable by non-destructive testing methods would improve significantly the present diagnostic techniques. This work has been made within the framework of the ADVANCE (Aging Diagnostic and Prognostics of Low-Voltage I\&C Cables) project, a FP7 European program. This Ph.D. thesis aims at studying the impact of aging on cable electrical parameters, in order to understand the evolution of the electrical properties associated with cable degradation. The identification of suitable aging markers requires the comparison of the electrical property variation with the physical/chemical degradation mechanisms of polymers for different insulating materials and compositions. The feasibility of non-destructive electrical condition monitoring techniques as potential substitutes for destructive methods will be finally discussed studying the correlation between electrical and mechanical properties. In this work, the electrical properties of cable insulators are monitored and characterized mainly by dielectric spectroscopy, polarization/depolarization current analysis and space charge distribution. Among these techniques, dielectric spectroscopy showed the most promising results; by means of dielectric spectroscopy it is possible to identify the frequency range where the properties are more sensitive to aging. In particular, the imaginary part of permittivity at high frequency, which is related to oxidation, has been identified as the most suitable aging marker based on electrical quantities.

Modeling factors that influence exercise and dietary change among midlife Australian women: results from the Healthy Aging of Women Study

The objective of this study was to investigate the factors that influence midlife women to make positive exercise and dietary changes. In late 2005 questionnaires were mailed to 866 women aged 51–66 years from rural and urban locations in Queensland, Australia and participating in Stage 2 of the Healthy Aging of Women Study. The questionnaires sought data on socio-demographics, body mass index (BMI), chronic health conditions, self-efficacy, exercise and dietary behavior change since age 40, and health-related quality of life. Five hundred and sixty four (69%) were completed and returned by early 2006. Data analysis comprised descriptive and bivariate statistics and structural equation modeling. The results showed that midlife is a significant time for women to make positive health behavior changes. Approximately one-third of the sample (34.6%) indicated that they had increased their exercise and around 60% had made an effort to eat more healthily since age 40. Modeling showed self-efficacy to be important in making both exercise and dietary changes. Although education appeared to influence self-efficacy in relation to exercise change, this was not the case for dietary change. The study has application for programs promoting healthy aging among women, and implies that those with low education, high BMI and poor mental health may need considerable support to improve their lifestyles.

Consumers’ concepts of materials

User needs and wants dictate the way in which products are designed, produced, used and disposed of. Western society in particular has become very consumer driven and the waste resulting from such activity has the potential to be disastrous. The creation of emotional attachment with possessions is one way of approaching sustainable consumer-product relationships. The aim of this research was to gain a deeper understanding of the interaction and emotional attachment that consumers have and develop with their products. It outlines literature relating to consumer emotion and experience in relation to products, and how pleasurable product user relationships can be prolonged. It is evident from the literature that the roles of materials in the emotional attachment consumers have with products needed to be further explored. A study was conducted to determine consumers. concepts of six materials currently used in product design. This involved participants being given a Concept Prompt Probe with textual prompts to assist in discussion about the materials in question. The discussions between the 15 participant groups of two people, one male and one female, were then transcribed and coded ready for analysis. The study findings demonstrate consumers. concepts of the six materials. The findings show both physical and emotional consumer concepts of the materials. It is, however, the interaction of these concepts that is the most significant finding of this research. Each material concept is not only judged emotionally by consumers in its own right but in relation to other concepts as well. The interaction of the consumers. concepts of materials can considerably effect the emotional judgement made about the material and the appropriateness of its application. This research makes a significant contribution to knowledge regarding the effect materials have on the consumers by identifying how materials can prompt emotional judgements and thereby alter the product user experience.

A longitudinal study of the relationship between lifestyle and mental health among midlife and older women in Australia : findings from the Healthy Aging of Women Study

We investigated the temporal relationship between lifestyle and mental health among 564 midlife women. The mental health measured included anxiety, depression, and mental well-being; the lifestyle measures included body mass index (BMI), exercise, smoking, alcohol use, and caffeine consumption. We found that BMI was positively related with mental well-being (r = .316, p = .009); smokers had lower mental well-being than nonsmokers (β = 6.725, p = .006), and noncaffeine drinkers had higher mental well-being (β = 5, p = .023). Past alcohol-drinkers had less anxiety than nondrinkers (β = 1.135, p = .04). Therefore, lifestyle is predictive of mental health among midlife and older women.

Flammability and Sensitivity of Materials in Oxygen-Enriched Atmospheres : 13th Volume

"Seventeen peer-reviewed papers cover the latest research on the ignition and combustion of metals and non-metals, oxygen compatibility of components and systems, analysis of ignition and combustion, failure analysis and safety. It includes aerospace, military, scuba diving, and industrial oxygen applications. Topics cover: • Development of safe oxygen systems • Ignition mechanisms within oxygen systems and how to avoid them • Specific hazards that exist with the oxygen mixture breathed by divers in the scuba industry • Issues related to oxygen system level safety • Issues related to oxygen safety in breathing systems • Detailed investigations and discussions related to the burn curves that have been generated for metals that are burning in a standard test fixture This new publication is a valuable resource for professionals in the air separation industries, oxygen manufacturers, manufacturers of materials intended for oxygen service, and users of oxygen and oxygen-enriched atmospheres, including aerospace, medical, industrial gases, chemical processing, steel and metals refining, as well as to military, commercial or recreational diving."--- publisher website

Predictors of mental health in post-menopausal women : results from the Australian healthy aging of women study

Objective: To examine the extent to which socio-demographics, modifiable lifestyle, and physical health status influence the mental health of post-menopausal Australian women. Methods: Cross-sectional data on health status, chronic disease and modifiable lifestyle factors were collected from a random cross-section of 340 women aged 60-70 years, residing in Queensland, Australia. Structural equation modelling (SEM) was used to measure the effect of a range of socio-demographic characteristics, modifiable lifestyle factors, and health markers (self-reported physical health, history of chronic illness) on the latent construct of mental health status. Mental health was evaluated using the Medical Outcomes Study Short Form 12 (SF-12®) which examined and Center for Epidemiologic Studies Depression Scale (CES-D). Results: The model was a good fit for the data (χ2=4.582, df=3, p=0.205) suggesting that mental health is negatively correlated with sleep disturbance (β = -0.612, p <0.001), and a history of depression (β = -0.141, p = 0.024).While mental health was associated with poor sleep, it was not correlated with most lifestyle factors (BMI, alcohol consumption, or cigarette smoking) or socio-demographics like age, income or employment category and they were removed from the final model. Conclusion: Research suggests that it is important to engage in a range of health promoting behaviours to preserve good health. We found that predictors of current mental health status included sleep disturbance, and past mental health problems, while socio-demographics and modifiable lifestyle had little impact. It may be however, that these factors influenced other variables associated with the mental health of post-menopausal women, and these relationships warrant further investigation.

Prevalence and correlates of sleep disturbance in post-menopausal Australian women : the Healthy Aging of Women (HOW) study

Background: Sleep disturbance in midlife women has been studied extensively, although less is known about sleep after menopause. This study examined the relative impact of socio-demographics, modifiable lifestyle factors, and health status on sleep disturbance in post-menopausal women from Queensland, Australia. Methods: The longitudinal Healthy Aging of Women (HOW) study examines health-related quality of life (HRQOL measured by SF-12©), chronic illness, modifiable lifestyle factors such as physical activity, alcohol consumption, smoking, and sleep disturbance (General Sleep Disturbance Scale, GSDS ≥ 43 represent poor sleep) in midlife and older women from low and high socio-economic, rural and urban areas of South-East Queensland, Australia. This paper presents cross-sectional data from the 322 women, aged 60-70 years, participating in the HOW study in 2011. Results: For women in this study, sleep disturbance was relatively common, with 23% (n = 83) reporting poor sleeping (GSDS ≥ 43). Sleep disturbance scores were strongly correlated with being unemployed or on a disability support pension (β = 18.69, P < 0.01), sedentary lifestyle (β = 23.84, P < 0.01), and lower mental (β = -0.60, P <0.01) and physical health-related quality of life scores (β = -0.32, P = 0.01), and these variables explained almost one third of variance in sleep disturbance scores (ηρ² = 29%). Conclusions: Multivariable analysis revealed that sleep disturbance was correlated with physical and mental health-related quality of life, disability, and sedentary lifestyle, but not other lifestyle and socio-demographic characteristics. It may be however, that modifiable lifestyle factors may indirectly impact on sleep by influencing health status.