Single step process for particles surface modification or thin film composite production

Adsorbent materials and composites are quite useful for sensor development. Therefore, the aim of this work is the surface modification of particulates and/or composite formation. The material was produced by plasma polymerization of HMDS (hexamethyldisilazane) in a single step. SEM analysis shows good surface coverage of particulates with a plasma polymerized film formed by several clusters that might increase adsorption. Particles (starch. 5 5 mu m) recovered with HMDS films show good properties for retention of medium-size Organic molecules, such as dye. Thin films formed by a mixture of particles and plasma polymerized thin film HMDS species were obtained in a single step and can be used for retention of organic compounds, in liquid or gaseous phase. (C) 2009 Elsevier B.V. All rights reserved.

Experimental Gravimetric Adsorption Equilibrium of n-Alkanes and Alkenes, Carbon Dioxide and Nitrogen in MIL-53(Al) and Zeolite 5A

Dissertação para obtenção do Grau de Mestre em Engenharia Química e Bioquímica

Upgrade of an experimental volumetric unit for gas adsorption equilibrium studies

In this work, a volumetric unit previously assembled by the research group was upgraded. This unit revamping was necessary due to the malfunction of the solenoid valves employed in the original experimental setup, which were not sealing the gas properly leading to erroneous adsorption equilibrium measurements. Therefore, the solenoid valves were substituted by manual ball valves. After the volumetric unit improvement its operation was validated. For this purpose, the adsorption equilibrium of carbon dioxide (CO2) at 323K and 0 - 20 bar was measured on two different activated carbon samples, in the of extrudates (ANG6) and of a honeycomb monolith (ACHM). The adsorption equilibrium results were compared with data previously measured by the research group, using a high-pressure microbalance from Rubotherm GmbH (Germany) – gravimetric. The results obtained using both apparatuses are coincident thus validating the good operation of the volumetric unit upgraded in this work. Furthermore, the adsorption equilibrium of CO2 at 303K and 0 - 10 bar on Metal-Organic Frameworks (MOFs) Cu-BTC and Fe-BTC was also studied. The CO2 adsorption equilibrium results for both MOFs were compared with the literature results showing good agreement, which confirms the good quality of the experimental results obtained in the new volumetric unit. Cu-BTC sample showed significantly higher CO2 adsorption capacity when compared with the Fe-BTC sample. The revamping of the volumetric unit included a new valve configuration in order to allow testing an alternative method for the measurement of adsorption equilibrium. This new method was employed to measure the adsorption equilibrium of CO2 on ANG6 and ACHM at 303, 323 and 353K within 0-10 bar. The good quality of the obtained experimental data was testified by comparison with data previously obtained by the research group in a gravimetric apparatus.

Nikkelille selektiivisen kelatoivan adsorbenttimateriaalin valmistus ja tutkiminen

Metallien laajamittaisen ja runsaan käytön vuoksi nykyään on keskityttävä aikaisempaa tarkemmin metallipäästöjen estämiseen ja puhdistamiseen. Metallien puhdistamiseen jätevesistä voidaan käyttää erilaisia yksikköoperaatiomenetelmiä, mutta selektiivisempään erotukseen päästään ioninvaihto- ja adsorbenttimateriaaleilla. Työn tarkoitusena on valmistaa ja tutkia nikkeliselektiivisiä adsorbenttimateriaaleja. Lisäksi tutkimuskohteena on nikkelin ja 1,10-fenantroliinin välisen kompleksin muodostuminen eri pH-arvoilla. Selektiivisten adsorbenttimateriaalien valmistaminen onnistuu liittämällä kiinteään kantajaan ligandi. Tämän työn tapauksessa nikkelitemplaatin liittäminen kiinteään kantajaan funktionalisointivaiheessa muodostaa adsorbenttiin nikkelille spesifisen kohdan. Käytännössä spesifisyyden syntyminen ei ole itsestäänselvyys, vaan se riippuu paljon funktionalisointitavasta. Tässä työssä funktionalisointitapana olivat fysikaalinen adsorptio ja impregnointi. Nikkelin ja 1,10-fenantroliinin välisen kompleksin muodostumista tutkittiin eri pH-arvojen lisäksi neljällä eri happokonsentraatiolla. Tuloksia verrattiin sellaisen liuoksen spektriin, missä oli pelkkää nikkeliä. Tuloksista havaittiin, että komplekseja muodostuu käytännössä samalla tavalla pH:n ollessa 1–6. Vasta 5 M HNO3 alkoi heikentää kompleksien muodostumista, ja 10 M HNO3 esti kompleksien muodostumisen täysin. Adsorbenttimateriaaleja valmistettiin useita erilaisia, joihin osaan liitettiin nikkelitemplaatti ja osa jätettiin ilman templaattia. Työssä keskityttiin tutkimaan erityisesti kolmea silikasta valmistettua materiaalia, joissa vain kahdessa oli nikkelitemplaatti. Nikkelitemplaattien olemassaololla ei havaittu olevan juurikaan merkitystä nikkelin erottamiseen vesiliuoksista. Materiaaleille tehdyt regenerointikokeet osoittivat, että materiaalien toiminta ja kapasiteetti eivät olleet toivotulla tasolla.

Ecotoxic Metal Records and its Degree of Geochemical Symphony in the Niche of Cochin Estuarine System- A Theraptic Perspective

The heavy metal contamination in the environment may lead to circumstances like bioaccumulation and inturn biomagnification. Hence cheaper and effective technologies are needed to protect the precious natural resources and biological lives. A suitable technique is the one which meets the technical and environmental criteria for dealing with a particular remediation problem and should be site-specific due to spatial and climatic variations and it may not economically feasible everywhere. The search for newer technologies for the environmental therapy, involving the removal of toxic metals from wastewaters has directed attention to adsorption, based on metal binding capacities of various adsorbent materials. Therefore, the present study aim to identify and evaluate the most current mathematical formulations describing sorption processes. Although vast amount of research has been carried out in the area of metal removal by adsorption process using activated carbon few specific research data are available in different scientific institutions. The present work highlights the seasonal and spatial variations in the distribution of some selected heavy metals among various geochemical phases of Cochin Estuarine system and also looked into an environmental theraptic/remedial approach by adsorption technique using activated charcoal and chitosan, to reduce and thereby controlling metallic pollution. The thesis has been addressed in seven chapters with further subdivisions. The first chapter is introductory, stating the necessity of reducing or preventing water pollution due to the hazardous impact on environment and health of living organisms and drawing it from a careful review of literature relevant to the present study. It provides a constricted description about the study area, geology, and general hydrology and also bears the major objectives and scope of the present study.

Modificação estrutural de bentonitas nacionais : caracterização e estudos de adsorção

São apresentados os aspectos teóricos, práticos e bibliográficos envolvidos no desenvolvimento da tese de doutorado intitulada Modificação estrutural de bentonitas nacionais: caracterização e estudos de adsorção. O trabalho consistiu no desenvolvimento de um material adsorvente a partir de bentonitas, do tipo montmorilonitas, modificadas estruturalmente com o objetivo de aumentar sua capacidade de adsorção de poluentes, orgânicos e inorgânicos. O estudo visa incrementar o valor agregado deste recurso mineral e insere-se na área de tratamento de efluentes líquidos usando adsorventes não tradicionais, eficientes e de baixo custo em substituição ao carvão ativado ou às resinas de troca iônica. Foram estudadas as propriedades físicas e químicas; distribuição de tamanho de partículas, área superficial, potenciais eletrocinéticos, capacidade de troca catiônica, composição mineralógica, morfologia superficial e espaçamento basal, bem como as propriedades adsorptivas dos argilominerais não tratados e modificados, não modificadas e pilarizadas respectivamente. Também são discutidos os mecanismos de adsorção envolvidos e o desenvolvimento de um reator contínuo (adsorção em flocos) e de separação sólido/líquido. As modificações estruturais dos argilominerais foram realizadas via homoionização com cloreto de cálcio e posterior intercalação com compostos orgânicos com ação quelante de metais. A FENAN, bentonita obtida pela intercalação com Orto Fenantrolina (OF), foi a que apresentou melhor viabilidade técnica em termos de adsorção, adsorção/dessorção, floculação e de acumulação de poluentes na forma floculada e não floculada. Adicionalmente os estudos de reversibilidade da intercalação revelaram a alta estabilidade da OF na FENAN, em soluções fortemente ácidas, onde aproximadamente 90% da OF permanece ligada à superfície da argila. A quantidade de OF adsorvida na forma de unidades micelares foi de 112 mg por grama de bentonita a pH 8,5 ± 0,5. A caracterização das bentonitas, via difração de Raios X, análise térmica, microscopia eletrônica de varredura e por microscopia de força atômica, revelou que as FENAN possuem um comportamento estrutural muito estável ao longo da seqüência de adsorção/dessorção e que após a adsorção de poluentes inorgânicos, o quelato metálico formado apresenta alta estabilidade dentro da estrutura da organobentonita. A capacidade de acumulação alcançada nas FENAN foi de 110 mg de Cu/g de bentonita, valor superior à de diversos materiais adsorventes alternativos propostos em outros trabalhos similares. Os estudos de acumulação das FENAN floculadas – FENANFLOC, indicaram que a presença de floculante, na quantidade utilizada, não afeta significativamente a capacidade de remoção das bentonitas modificadas. Este comportamento apresentado, permitiu o desenvolvimento do Reator Expandido de Flocos Adsorventes (REFA), cujas características e parâmetros operacionais são discutidos em detalhe. Finalmente, os resultados são discutidos em termos dos fenômenos interfaciais envolvidos e dos potenciais práticos deste novo adsorvente e da nova técnica de adsorção em flocos no REFA.

Estudo de adsorvente obtido de terras diatomáceas para remoção de metais pesados em águas produzidas: processamento, caracterização e dinâmica em leito fixo

The acceleration of industrial growth in recent decades on all continents aroused the interest of the companies to counter the impacts produced on the environment, spurred primarily by major disasters in the petroleum industry. In this context, the water produced is responsible for the largest volume of effluent from the production and extraction of oil and natural gas. This effluent has in its composition some critical components such as inorganic salts, heavy metals (Fe, Cu, Zn, Pb, Cd, ), presence of oil and chemicals added in the various production processes. In response to impact, have been triggered by research alternative adsorbent materials for water treatment and water produced, in order to removing oils and acids and heavy metals. Many surveys of diatomaceous earth (diatomite) in Brazil involve studies on the physico-chemical, mineral deposits, extraction, processing and applications. The official estimated Jazi are around 2.5 million tonnes, the main located in the states of Bahia (44%) and Rio Grande do Norte (37,4%). Moreover, these two states appear as large offshore producers, earning a prominent role in research of adsorbents such as diatomite for treatment of water produced. Its main applications are as an agent of filtration, adsorption of oils and greases, industrial load and thermal insulator. The objective of this work was the processing and characterization of diatomite diatomaceous earth obtained from the municipality of Macaíba-RN (known locally as tabatinga) as a low cost regenerative adsorbent for removal of heavy metals in the application of water produced treatment. In this work we adopted a methodology for batch processing, practiced by small businesses located in producing regions of Brazil. The characterization was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and specific surface area (BET). Research conducted showed that the improvement process used was effective for small volume production of diatomite concentrated. The diatomite obtained was treated by calcination at temperature of 900 oC for 2 hours, with and without fluxing Na2CO3 (4%), according to optimal results in the literature. Column adsorption experiments were conducted to percolation of the in nature, calcined and calcined fluxing diatomites. Effluent was used as a saline solution containing ions of Cu, Zn, Na, Ca and Mg simulating the composition of produced waters in the state of Rio Grande do Norte, Brazil. The breakthrough curves for simultaneous removal of copper ions and zinc as a result, 84.3% for calcined diatomite and diatomite with 97.3 % for fluxing. The calcined fluxing diatomite was more efficient permeability through the bed and removal of copper and zinc ions. The fresh diatomite had trouble with the permeability through the bed under the conditions tested, compared with the other obtained diatomite. The results are presented as promising for application in the petroleum industry

Simulação de reservatórios não convencionais para armazenamento de gás natural veicular

The investigation of viability to use containers for Natural Gas Vehicle (NGV) storage, with different geometries of commercial standards, come from necessity to join the ambient, financial and technological benefits offered by the gas combustion, to the convenience of not modify the original proposal of the automobile. The use of these current cylindrical models for storage in the converted vehicles is justified by the excellent behavior that this geometry presents about the imposed tensions for the high pressure that the related reservoirs are submitted. However, recent research directed toward application of adsorbent materials in the natural gas reservoirs had proven a substantial redusction of pressure and, consequently, a relief of the tensions in the reservoirs. However, this study considers alternative geometries for NGV reservoirs, searching the minimization of dimensions and weight, remaining capacity to resist the tensions imposed by the new pressure situation. The proposed reservoirs parameters are calculated through a mathematical study of the internal pressure according to Brazilian standards (NBR) for pressure vessels. Finally simulations of the new geometries behavior are carried through using a commercially avaible Finite Element Method (FEM) software package ALGOR® to verify of the reservoirs efficincy under the gas pressure load

Capacidad y comportamiento de la adsorción de fenol en caolines naturales y modificados

En la actualidad las industrias químicas, farmacéuticas y clínicas, originan contaminantes en aguas superficiales, aguas subterráneas y suelos de nuestro país, como es el caso del fenol, contaminante orgánico común y altamente dañino para los organismos, incluso a bajas concentraciones. Existen en el mercado diferentes metodologías para minimizar la contaminación pero muchos de estos procesos tienen un alto coste, generación de contaminantes, etc. La adsorción de contaminantes por medio de arcillas es un método ampliamente utilizado, encontrándose eficaz y económico. Pero la dificultad de adsorber un contaminante orgánico como el fenol motiva la creación de un material llamado organoarcillas. Las organoarcillas son arcillas modificadas con un surfactante, a su vez, los surfactantes son moléculas orgánicas que confieren a la superficie de la arcilla carga catiónica en lugar de aniónica, haciendo más fácil la adsorción de fenol. Para esta tesis se ha elegido el caolín como material adsorbente, fácilmente disponible y relativamente de bajo coste. Se ha trabajado con: arenas de caolín, material directo de la extracción, y caolín lavado, originado del proceso de lavado de las arenas de caolín. Ambos grupos se diferencian fundamentalmente por su contenido en cuarzo, ampliamente mayor en las arenas de caolín. Con el objetivo de desarrollar un material a partir del caolín y arenas de éste con capacidad de retención de contaminates, en concreto, fenol, se procedió a modificar los materiales de partida mediante tratamientos térmicos, mecánicos y/o químicos, dando lugar a compuestos con mayor superficie química reactiva. Para ello se sometió el caolín y las arenas caoliníferas a temperaturas de 750ºC durante 3h, a moliendas hasta alcanzar su amorfización, y/o a activaciones con HCl 6M o con NaOH 5M durante 3h a 90ºC. En total se obtuvieron 18 muestras, en las que se estudiaron las características físico-químicas, mineralógicas y morfológicas de cada una de ellas con el fin de caracterizarlas después de haber sufrido los tratamientos y/o activaciones químicas. Los cambios producidos fueron estudiados mediante pH, capacidad de intercambio catiónico (CEC), capacidad de adsorción de agua (WCU y CWC), distribución de tamaño de partícula (PSD), área de superficie específica (SBET), difracción de rayos X (XRD), espectroscopía infrarroja por transformada de Fourier (FTIR), métodos térmicos (TG, DTG y DTA), y microscopía electrónica de transmisión y barrido (SEM y TEM). Además se analizó los cambios producidos por los tratamientos en función de las pérdidas de Al y Si que acontece en las 18 muestras. Los resultados para los materiales derivados de la arenas caoliníferas fueron similares a los obtenidos para los caolines lavados, la diferencia radica en la cantidad de contenido de caolinita en los diferente grupos de muestras. Apoyándonos en las técnicas de caracterización se puede observar que los tratamientos térmico y molienda produce materiales amorfos, este cambio en la estructura inicial sumado a las activaciones ácida y alcalina dan lugar a pérdidas de Si y Al, ocasionando que sus propiedades físico-químicas, mineralógicas y morfológicas se vean alteradas. Un fuerte aumento es observado en las áreas superficiales y en la CEC en determinadas muestras, además entre los cambios producidos se encuentra la producción de diferentes zeolitas en porcentajes distintos con el tratamiento alcalino. Para la obtención de las organoarcillas, las 18 muestras se sometieron a la surfactación con hexadeciltrimetil amonio (HDTMA) 20 mM durante 24h a 60ºC, esta concentración de tensioactivo fue más alta que la CEC de cada muestra. Los camext bios anteriormente producidos por los tratamientos y activaciones, afectan de forma diferente en la adsorción de HDTMA, variando por tanto la adsorción del surfactante en la superficie de las muestras. Se determinó el tensioactivo en superficie por FTIR, además se realizó un análisis de componentes principales (PCA) para examinar la dependencia entre las relaciones Si/Al de las muestras en la capacidad de adsorción de tensioactivo, y para el estudio de la adsorción de HDTMA en las muestras se realizaron además del análisis termogravimétrico, aproximaciones con los modelos de Freundllich y Langmuir. Se persigue conocer las diferentes formas y maneras que tiene el tensioactivo de fijarse en la superficie de las muestras. En las organoarcillas resultantes se cuantificó el fenol adsorbido cuando éstas fueron puestas en contacto con diferentes concentraciones de fenol: 50, 500, 1000, 2000, y 2500 mg/l durante 24h. El contaminante sorbido se calculó por medio de cromatografía de gases, y se realizaron aproximaciones con los modelos de Freundllich y Langmuir. El comportamiento de adsorción de fenol en arcillas orgánicas es regido por las características de las muestras. De forma general se puede decir que las muestras de caolines lavados tienen más capacidad de adsorción de fenol que las muestras de arenas de caolín y que la activación alcalina ha proporcionado una mejora en la adsorción de fenol en los dos grupos. En consecuencia se han obtenido materiales adsorbentes heterogéneos y por tanto, con propiedades diferentes. Se ha evaluado el comportamiento global de las arenas de caolín por un lado y del caolín lavado por otro. Las arenas de caolín presentan altos niveles de cuarzo y su uso para ciertos tipos de industrias no son recomendados en ocasiones por el alto costo que el proceso de limpieza y purificación implicaría. Por ello es importante reseñar en este proyecto las aplicaciones que ofrecen algunas muestras de este grupo. Los ensayos acontecidos en esta tesis han dado lugar a las siguientes publicaciones: • Pérdida de Al y Si en caolines modificados térmica- o mecánicamente y activados por tratamientos químicos. A. G. San Cristóbal, C Vizcayno, R. Castelló. Macla 9, 113-114. (2008). • Acid activation of mechanically and thermally modfied kaolins. A. G. San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Mater. Res. Bull. 44 (2009) 2103-2111. • Zeolites prepared from calcined and mechanically modified kaolins. A comparative study. A. G San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Applied Clay Science 49 (2010) 239-246. • Study comparative of the sorption of HDTMA on natural and modified kaolin. A. G San Cristóbal, R. Castelló, J. M. Castillejo, C Vizcayno. Aceptada en Clays and Clay minerals. • Capacity of modified kaolin sand and washed kaolin to adsorb phenol. A. G San Cristóbal, R. Castelló, C Vizcayno. Envío a revista sujeto a la publicación del artículo anterior. ABSTRACT Today’s chemical, pharmaceutical and clinical industries generate pollutants that affect the soils and surface and ground waters of our country. Among these, phenol is a common organic pollutant that is extremely harmful to living organisms, even at low concentrations. Several protocols exist to minimize the effects of pollutants, but most are costly procedures or even generate other pollutants. The adsorption of hazardous materials onto clays is perhaps the most used, efficient and cost-saving method available. However, organic compounds such as phenol are difficult to adsorb and this has led to the development of materials known as organoclays, which are much better at remediating organic compounds. Organoclays are clays that have been modified using a surfactant. In turn, surfactants are organic molecules that confer a cationic rather than anionic charge to the clay surface, improving it’s capacity to adsorb phenol. For this doctorate project, kaolin was selected as an adsorbent material for the removal of phenol given its easy sourcing and relatively low cost. The materials investigated were kaolin sand, a directly extracted material, and washed kaolin, which is the byproduct of the kaolin sand washing process. The main difference between the materials is their quartz content, which is much higher in the kaolin sands. To generate a product from kaolin or kaolin sand capable of retaining organic pollutants such as phenol, both materials were subjected to several heat, chemical and/or mechanical treatments to give rise to compounds with a greater reactive surface area. To this end the two starting materials underwent heating at 750ºC for 3 h, grinding to the point of amorphization and/or activation with HCl 6M or NaOH 5M for 3 h at 90ºC. These treatments gave rise to 18 processed samples, which were characterized in terms of their morphological, mineralogical, and physical-chemical properties. The behaviour of these new materials was examined in terms of their pH, cation exchange capacity (CEC), water adsorption capacity (WCU and WCC), particle size distribution (PSD), specific surface area (SBET), and their X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermal (DTG, DTA) and scanning and transmission electron microscopy (SEM and TEM) properties. The changes conferred by the different treatments were also examined in terms of Al and Si losses. Results for the materials derived from kaolin sands and washed kaolin were similar, with differences attributable to the kaolinite contents of the samples. The treatments heat and grinding produced amorphous materials, which when subjected to acid or alkali activation gave rise to Si and Al losses. This in turn led to a change in physico- chemical, mineralogical and morphological properties. Some samples showed a highly increased surface area and CEC. Further, among the changes produced, alkali treatment led to the generation of zeolites in different proportions depending on the sample. To produce the organoclays, the 18 samples were surfacted with hexadecyltrimethylammonium (HDTMA) 20 mM for 24 h at 60ºC. This surfactant concentration is higher than the CEC of each sample. The amount of HDTMA adsorbed onto the surface of each sample determined by FTIR varied according to treatment. A principle components analysis (PCA) was performed to examine correlations between sample Si/Al ratios and surfactant adsorption capacity. In addition, to explore HDTMA adsorption by the samples, DTG and DTA data were fitted to Freundllich and Langmuir models. The mechanisms of surfactant attachment to the sample surface were also addressed. The amount of phenol adsorbed by the resultant organoclays was determined when exposed to different phenol concentrations: 50, 500, 1000, 2000, and 2500 mg/l for 24 h. The quantity of adsorbed pollutant was estimated by gas chromatography and the data fitted to the models of Freundllich and Langmuir. Results indicate that the phenol adsorption capacity of the surfacted samples is dependent on the sample’s characteristics. In general, the washed kaolin samples showed a greater phenol adsorption capacity than the kaolon sands and alkali activation improved this capacity in the two types of sample. In conclusion, the treatments used gave rise to adsorbent materials with varying properties. Kaolin sands showed high quartz levels and their use in some industries is not recommended due to the costs involved in their washing and purification. The applications suggested by the data obtained for some of the kaolin sand samples indicate the added value of this industrial by-product. The results of this research project have led to the following publications: • Pérdida de Al y Si en caolines modificados térmica- o mecánicamente y activados por tratamientos químicos. A. G. San Cristóbal, C Vizcayno, R. Castelló. Macla 9, 113-114. (2008). • Acid activation of mechanically and thermally modfied kaolins. A. G. San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Mater. Res. Bull. 44 (2009) 2103-2111. • Zeolites prepared from calcined and mechanically modified kaolins. A comparative study. A. G. San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Applied Clay Science 49 (2010) 239-246. • Study comparative of the sorption of HDTMA on natural and modified kaolin. A. G. San Cristóbal, R. Castelló, J. M. Castillejo, C Vizcayno Accepted in Clays and Clay minerals. • Capacity of modified kaolin sand and washed kaolin to adsorb phenol. A. G San Cristóbal, R. Castelló, C Vizcayno. Shipment postponed, subject to the publication of the previous article.

Síntese, caracterização e modificação de superfícies de sílicas mesoporosas ordenadas para captura de CO2

Processos como a purificação do metano (CH4) e a produção de hidrogênio gasoso (H2) envolvem etapas de separação de CO2. Atualmente, etanolaminas como monoetanolamina (MEA), dietanolamina (DEA), metildietanolamina (MDEA) e trietanolamina (TEA) são as substâncias mais utilizadas no processo de separação/captura de CO2 em processos industriais. Entretanto, o uso destas substâncias apresenta alguns inconvenientes devido à alta volatilidade, dificuldade de se trabalhar com material líquido, também ao alto gasto energético envolvido das etapas de regeneração e à baixa estabilidade térmica e química. Com base nessa problemática, esse trabalho teve por objetivo a síntese de um tipo de sílica mesoporosa altamente ordenada (SBA-15) de modo a utilizá-la no processo de captura de CO2. O trabalho foi dividido em quatro etapas experimentais que envolveram a síntese da SBA-15, o estudo do comportamento térmico de algumas etanolaminas livres, síntese e caracterização de materiais adsorventes preparados a partir de incorporação de etanolaminas à SBA-15 e estudo da eficiência de captura de CO2 por esses materiais. Novas alternativas de síntese da SBA-15 foram estudadas neste trabalho, visando aperfeiçoar as propriedades texturais do material produzido. Tais alternativas são baseadas na remoção do surfatante, utilizado como molde na síntese da sílica mesoporosa, por meio da extração por Soxhlet, utilizando diferentes solventes. O processo contribuiu para melhorar as propriedades do material obtido, evitando o encolhimento da estrutura que pode ser ocasionado durante a etapa de calcinação. Por meio de técnicas como TG/DTG, DSC, FTIR e Análise Elementar de C, H e N foi realizada a caracterização físico-química e termoanalítica da MEA, DEA, MDEA e TEA, visando melhor conhecer as características destas substâncias. Estudos cinéticos baseados nos métodos termogravimétricos isotérmicos e não isotérmicos (Método de Ozawa) foram realizados, permitindo a determinação de parâmetros cinéticos envolvidos nas etapas de volatilização/decomposição térmica das etanolaminas. Além das técnicas acima mencionadas, MEV, MET, SAXS e Medidas de Adsorção de N2 foram utilizadas na caraterização da SBA-15 antes e após a incorporação das etanolaminas. Dentre as etanolaminas estudadas, a TEA apresentou maior estabilidade térmica, entretanto, devido ao seu maior impedimento estérico, é a etanolamina que apresenta menor afinidade com o CO2. Diferentemente das demais etanolaminas estudadas, a decomposição térmica da DEA envolve uma reação intramolecular, levando a formação de MEA e óxido de etileno. A incorporação destes materiais à SBA-15 aumentou a estabilidade térmica das etanolaminas, uma vez que parte do material permanece dentro dos poros da sílica. Os ensaios de adsorção de CO2 mostraram que a incorporação da MEA à SBA-15 catalisou o processo de decomposição térmica da mesma. A MDEA foi a etanolamina que apresentou maior poder de captura de CO2 e sua estabilidade térmica foi consideravelmente aumentada quando a mesma foi incorporada à SBA-15, aumentando também seu potencial de captura de CO2.

Characterization of carbon molecular sieves using methane and carbon dioxide as adsorptive probes

Nitrogen adsorption at 77 K is the current standard means for pore size determination of adsorbent materials. However, nitrogen adsorption reaches limitations when dealing with materials such as molecular sieving carbon with a high degree of ultramicroporosity. In this investigation, methane and carbon dioxide adsorption is explored as a possible alternative to the standard nitrogen probe. Methane and carbon dioxide adsorption equilibria and kinetics are measured in a commercially derived carbon molecular sieve over a range of temperatures. The pore size distribution is determined from the adsorption equilibrium, and the kinetics of adsorption is shown to be Fickian for carbon dioxide and non-Fickian for methane. The non-Fickian response is attributed to transport resistance at the pore mouth experienced by the methane molecules but not by the carbon dioxide molecules. Additionally, the change in the rate of adsorption with loading is characterized by the Darken relation in the case of carbon dioxide diffusion but is greater than that predicted by the Darken relation for methane transport. Furthermore, the proposition of inkbottle-shaped micropores in molecular sieving carbon is supported by the determination of the activation energy for the transport of methane and subsequent sizing of the pore-mouth barrier by molecular potential calculations.

Estudo de adsorvente obtido de terras diatomáceas para remoção de metais pesados em águas produzidas: processamento, caracterização e dinâmica em leito fixo

The acceleration of industrial growth in recent decades on all continents aroused the interest of the companies to counter the impacts produced on the environment, spurred primarily by major disasters in the petroleum industry. In this context, the water produced is responsible for the largest volume of effluent from the production and extraction of oil and natural gas. This effluent has in its composition some critical components such as inorganic salts, heavy metals (Fe, Cu, Zn, Pb, Cd, ), presence of oil and chemicals added in the various production processes. In response to impact, have been triggered by research alternative adsorbent materials for water treatment and water produced, in order to removing oils and acids and heavy metals. Many surveys of diatomaceous earth (diatomite) in Brazil involve studies on the physico-chemical, mineral deposits, extraction, processing and applications. The official estimated Jazi are around 2.5 million tonnes, the main located in the states of Bahia (44%) and Rio Grande do Norte (37,4%). Moreover, these two states appear as large offshore producers, earning a prominent role in research of adsorbents such as diatomite for treatment of water produced. Its main applications are as an agent of filtration, adsorption of oils and greases, industrial load and thermal insulator. The objective of this work was the processing and characterization of diatomite diatomaceous earth obtained from the municipality of Macaíba-RN (known locally as tabatinga) as a low cost regenerative adsorbent for removal of heavy metals in the application of water produced treatment. In this work we adopted a methodology for batch processing, practiced by small businesses located in producing regions of Brazil. The characterization was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and specific surface area (BET). Research conducted showed that the improvement process used was effective for small volume production of diatomite concentrated. The diatomite obtained was treated by calcination at temperature of 900 oC for 2 hours, with and without fluxing Na2CO3 (4%), according to optimal results in the literature. Column adsorption experiments were conducted to percolation of the in nature, calcined and calcined fluxing diatomites. Effluent was used as a saline solution containing ions of Cu, Zn, Na, Ca and Mg simulating the composition of produced waters in the state of Rio Grande do Norte, Brazil. The breakthrough curves for simultaneous removal of copper ions and zinc as a result, 84.3% for calcined diatomite and diatomite with 97.3 % for fluxing. The calcined fluxing diatomite was more efficient permeability through the bed and removal of copper and zinc ions. The fresh diatomite had trouble with the permeability through the bed under the conditions tested, compared with the other obtained diatomite. The results are presented as promising for application in the petroleum industry

Adsorbent new materials and composites produced in a single step

The aim of this work is the production and preliminary characterization of adsorbent new materials useful for sensor development. A new plasma chamber was simulated and designed in order to obtain multiple layers and/or composites in a single step. Plasma deposited organic fluorocompound and hexamethyldisilazane (HMDS) thin films were produced and tested as adsorbent layers. Chemical characterization used ellipsometry, Raman. infrared and X-ray photoelectron spectroscopy. Hydrophobic and oleophobic character were determined by contact angle measurements. Adsorption characteristics were evaluated using quartz crystal microbalance. Not only HMDS but also the fluorocompound can polymerize but intermixing and a double layer are only obtained in very narrow conditions. The films are adsorbent and mildly hydrophobic. Films deposited on a microchromatographic column can be used on sample pretreatment to remove and/or preconcentrate volatile organic Compounds. Therefore, with this approach it is possible to obtain films with different monomers on double layer or composites, with organic/inorganic materials or particles and use them on sample pretreatment for chemical analysis. (C) 2008 Elsevier B.V. All rights reserved.

Corrosion resistant and adsorbent plasma polymerized thin film

Adsorbent and corrosion resistant films are useful for sensor development. Therefore, the aim of this work is the production and characterization of plasma polymerized fluorinated organic ether thin films for sensor development. The polymerized reactant was methyl nonafluoro(iso)butyl ether. Infrared Spectroscopy showed fluorinated species and eventually CO but CH(n) is a minor species. Contact angle measurements indicated that the film is hydrophobic and organophilic but oleophobic. Optical microscopy reveals not only a good adherence on metals and acrylic but also resistance for organic solvents, acid and basic aqueous solution exposure. Double layer and intermixing are possible and might lead to island formation. Quartz Crystal Microbalance showed that 2-propanol permeates the film but there is no sensitivity to n-hexane. The microreactor manufactured using a 73 cm long microchannel can retain approximately 9 X 10(-4) g/cm(2) of 2-propanol in vapor phase. Therefore, the film is a good candidate for preconcentration of volatile organic compounds even in corrosive environment. (C) 2009 Elsevier B.V. All rights reserved.

Natural waste materials containing chitin as adsorbents for textile dyestuffs: batch and continuous studies

In this work three natural waste materials containing chitin were used as adsorbents for textile dyestuffs, namely the Anodonta (Anodonta cygnea) shell, the Sepia (Sepia officinalis) and the Squid (Loligo vulgaris) pens. The selected dyestuffs were the Cibacron green T3G-E (CI reactive green 12), and the Solophenyl green BLE 155% (CI direct green 26), both from CIBA, commonly used in cellulosic fibres dyeing, the most used fibres in the textile industry. Batch equilibrium studies showed that the materials’ adsorption capacities increase after a simple and inexpensive chemical treatment, which increases their porosity and chitin relative content. Kinetic studies suggested the existence of a high internal resistance in both systems. Fixed bed column experiments performed showed an improvement in adsorbents’ behaviour after chemical treatment. However, in the column experiments, the biodegradation was the main mechanism of dyestuff removal, allowing the materials’ bioregeneration. The adsorption was strongly reduced by the pore clogging effect of the biomass. The deproteinised Squid pen (grain size 0.500–1.41 mm) is the adsorbent with highest adsorption capacity (0.27 and 0.037 g/g, respectively, for the reactive and direct dyestuffs, at 20ºC), followed by the demineralised Sepia pen and Anodonta shell, behaving like pure chitin in all experiments, but showing inferior performances than the granular activated carbon tested in the column experiments.