Development of new sound absorbing materials for noise suppressors.

"Materials Laboratory, Contract no. AF33(616)-5060, Project no. 7231."

Projeto e construção de uma câmara reverberante em escala reduzida para a caracterização acústica de materiais absorventes

Na área da Acústica, no que diz respeito às últimas décadas, tem crescido substancialmente a demanda por informações sobre a capacidade de absorção dos materiais acústicos, bem como a utilização de métodos de modelagem que permitam inferir o comportamento acústico dos sistemas reais, os quais demandam uma infraestrutura de porte, o que representa um alto investimento. Assim, visando atender a estas demandas, possibilitar o desenvolvimento de pesquisas sobre as características de absorção sonora de materiais tipicamente regionais e o desenvolvimento de aulas práticas no âmbito da acústica, tanto no curso de graduação quanto na pós-graduação, este trabalho apresenta todas as informações pertinentes ao projeto e construção de uma mini-câmara reverberante, na escala de 1: 6 de um volume de 200 m³. Além disso, é apresentada uma metodologia de qualificação e adequação do campo acústico interno, tendo por base as orientações contidas na norma ISO-354. Por outro lado, são apresentados e discutidos os resultados obtidos, a partir de ensaios realizados nesta mini-câmara, caracterizando e validando os painéis de fibra de coco, desenvolvidos pelo Grupo de Vibração e Acústica, da Universidade Federal do Pará, bem como uma simulação numérica por Raios Acústicos, tendo por base a cavidade acústica da minicâmara, para permitir a validação do modelo numérico a partir dos dados experimentais.

Realización de un procedimiento para la medida del coeficiente de absorción sonora normal

El objetivo de este trabajo es la elaboración de un procedimiento para la medida del coeficiente de absorción sonora normal en un tubo de impedancia. Para ello se han estudiado los fundamentos básicos de la ecuación de ondas y sus soluciones. Se han considerado las soluciones pertinentes que describen el comportamiento de una onda sonora dentro de un tubo rígido. Se ha considerado también la teoría básica de funciones de transferencia. Estas teorías son claves a la hora de poder desarrollar el procedimiento de medida, ya que el coeficiente de absorción acústica se obtendrá con la ayuda de un tubo de impedancias que mide las funciones de transferencia entre dos posiciones de micrófonos incorporados en una de las caras del tubo. La utilización de esta técnica tiene como principal ventaja, la necesidad de poco espacio en un laboratorio y el empleo de muestras pequeñas de material. La implementación de los visto teóricamente a su aplicación práctica se ha hecho a través de un procedimiento de medida que sigue la Norma UNE-EN ISO 10534-2 (2002) “Determinación del coeficiente de absorción sonoro y la impedancia en tubos de impedancia Parte 2: método función de transferencia”. El valor del coeficiente de absorción se puede obtener a través de una instrumentación específica y un programa computador. Para poder validar los cálculos que realiza el programa utilizado, se ha realizado una batería de medidas del coeficiente de absorción a diferentes tipos de materiales acústicos, y los cálculos se han hecho por la vía del programa y por la vía de una hoja de cálculo. Como parte del procedimiento de medida se ha calculado la incertidumbre en las medidas. En definitiva se pretende contribuir con este trabajo a establecer un procedimiento de medida del comportamiento acústico de diversos materiales. SUMMARY. The aim of this work is the development of a procedure for measuring the sound absorption coefficient normal of an impedance tube. To this end we have studied the basics of the wave equation and its solutions. We have considered the relevant solutions that describe the behavior of a sound wave in a rigid tube. It has also considered the basic theory of transfer functions. These theories are key when we want to develop the measurement method, since the absorption coefficient is obtained with the aid of an impedance tube measuring transfer functions between two positions of microphones incorporated into one side of the tube. The use of this technique has the main advantage, the need of little space on a laboratory and use of small samples of material. The implementation of theoretically seen to his practical application has been made through a measurement procedure following the UNE-EN ISO 10534-2 (2002) "Determination of sound absorption coefficient and impedance in impedance tubes Part 2 : transfer function method ". The value of the absorption coefficient can be obtained through a specific instrumentation and computer software. In order to validate the calculations performed by the program used, there has been realized a series of measures of the absorption coefficient at different types of acoustical materials, and calculations were made by means of the program and by means of a spreadsheet. As part of the measurement procedure has been estimated uncertainty in the measurements. Ultimately it’s tried to contribute with this work to establish a procedure measuring the acoustic behavior of various materials.

Magneto acoustical emission in nanocrystalline Mn-Zn ferrites

Mn0.4Zn0.6Fe2O4 powders were prepared by microwave hydrothermal method. The powders were characterized by X-ray diffraction, transmission electron microscope. The powders were sintered at different temperatures 400, 500, 600, 700, 800 and 900 degrees C/30 min using microwave sintering method. The grain size was estimated by scanning electron microscope. The room temperature dielectric and magnetic properties were studied in the frequency range (100 kHz-1.8 GHz). The magnetization properties were measured upto 1.5 T. The acoustic emission has been measured along the hysteresis loops from 80 K to Curie temperature. It is found that the magneto-acoustic emission (MAE) activity along hysteresis loop is proportional to the hysteresis losses during the same loop. This law has been verified on series of polycrystalline ferrites and found that the law is valid whatever the composition, the grain size and temperature. It is also found that the domain wall creation/or annihilation processes are the origin of the MAE. (C) 2013 Published by Elsevier Ltd.

Vibro-acoustical analysis and design of a multiple-layer constrained viscoelastic damping structure

The goal of this research is to provide a framework for vibro-acoustical analysis and design of a multiple-layer constrained damping structure. The existing research on damping and viscoelastic damping mechanism is limited to the following four mainstream approaches: modeling techniques of damping treatments/materials; control through the electrical-mechanical effect using the piezoelectric layer; optimization by adjusting the parameters of the structure to meet the design requirements; and identification of the damping material’s properties through the response of the structure. This research proposes a systematic design methodology for the multiple-layer constrained damping beam giving consideration to vibro-acoustics. A modeling technique to study the vibro-acoustics of multiple-layered viscoelastic laminated beams using the Biot damping model is presented using a hybrid numerical model. The boundary element method (BEM) is used to model the acoustical cavity whereas the Finite Element Method (FEM) is the basis for vibration analysis of the multiple-layered beam structure. Through the proposed procedure, the analysis can easily be extended to other complex geometry with arbitrary boundary conditions. The nonlinear behavior of viscoelastic damping materials is represented by the Biot damping model taking into account the effects of frequency, temperature and different damping materials for individual layers. A curve-fitting procedure used to obtain the Biot constants for different damping materials for each temperature is explained. The results from structural vibration analysis for selected beams agree with published closed-form results and results for the radiated noise for a sample beam structure obtained using a commercial BEM software is compared with the acoustical results of the same beam with using the Biot damping model. The extension of the Biot damping model is demonstrated to study MDOF (Multiple Degrees of Freedom) dynamics equations of a discrete system in order to introduce different types of viscoelastic damping materials. The mechanical properties of viscoelastic damping materials such as shear modulus and loss factor change with respect to different ambient temperatures and frequencies. The application of multiple-layer treatment increases the damping characteristic of the structure significantly and thus helps to attenuate the vibration and noise for a broad range of frequency and temperature. The main contributions of this dissertation include the following three major tasks: 1) Study of the viscoelastic damping mechanism and the dynamics equation of a multilayer damped system incorporating the Biot damping model. 2) Building the Finite Element Method (FEM) model of the multiple-layer constrained viscoelastic damping beam and conducting the vibration analysis. 3) Extending the vibration problem to the Boundary Element Method (BEM) based acoustical problem and comparing the results with commercial simulation software.

Experimental studies on comparison of microwave curing and thermal curing of epoxy resins used for alternative mould materials

In this present work attempts have been made to study the glass transition temperature of alternative mould materials by using both microwave heating and conventional oven heating. In this present work three epoxy resins, namely R2512, R2515 and R2516, which are commonly used for making injection moulds have been used in combination with two hardeners H2403 and H2409. The magnetron microwave generator used in this research is operating at a frequency of 2.45 GHz with a hollow rectangular waveguide. In order to distinguish the effects between the microwave and conventional heating, a number of experiments were performed to test their mechanical properties such as tensile and flexural strengths. Additionally, differential scanning calorimeter technique was implemented to measure the glass transition temperature on both microwave and conventional heating. This study provided necessary evidences to establish that microwave heated mould materials resulted with higher glass transition temperature than the conventional heating. Finally, attempts were also made to study the microstructure of microwave-cured materials by using a scanning electron microscope in order to analyze the morphology of cured specimens.