Utilização de resíduos de cinza de casca de arroz e borracha de pneus em concreto de alto desempenho

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Strength prediction of single- and double-lap joints by standard and extended finite element modelling

The structural integrity of multi-component structures is usually determined by the strength and durability of their unions. Adhesive bonding is often chosen over welding, riveting and bolting, due to the reduction of stress concentrations, reduced weight penalty and easy manufacturing, amongst other issues. In the past decades, the Finite Element Method (FEM) has been used for the simulation and strength prediction of bonded structures, by strength of materials or fracture mechanics-based criteria. Cohesive-zone models (CZMs) have already proved to be an effective tool in modelling damage growth, surpassing a few limitations of the aforementioned techniques. Despite this fact, they still suffer from the restriction of damage growth only at predefined growth paths. The eXtended Finite Element Method (XFEM) is a recent improvement of the FEM, developed to allow the growth of discontinuities within bulk solids along an arbitrary path, by enriching degrees of freedom with special displacement functions, thus overcoming the main restriction of CZMs. These two techniques were tested to simulate adhesively bonded single- and double-lap joints. The comparative evaluation of the two methods showed their capabilities and/or limitations for this specific purpose.

Motor unit synchronization measured by cross-correlation is not influenced by short-term strength training of a hand muscle

The purpose of the study was to quantify the strength of motor unit synchronization and coherence from pairs of concurrently active motor units before and after short-term (4–8 weeks) strength training of the left first dorsal interosseous (FDI) muscle. Five subjects (age 24.8 ± 4.3 years) performed a training protocol three times/week that consisted of six sets of ten maximal isometric index finger abductions, whereas three subjects (age 27.3 ± 6.7 years) acted as controls. Motor unit activity was recorded from pairs of intramuscular electrodes in the FDI muscle with two separate motor unit recording sessions obtained before and after strength training (trained group) or after 4 weeks of normal daily activities that did not involve training (control group). The training intervention resulted in a 54% (45.2 ± 8.3 to 69.5 ± 13.8 N, P = 0.001) increase in maximal index finger abduction force, whereas there was no change in strength in the control group. A total of 163 motor unit pairs (198 single motor units) were examined in both subject groups, with 52 motor unit pairs obtained from 10 recording sessions before training and 51 motor unit pairs from 10 recording sessions after training. Using the cross-correlation procedure, there was no change in the strength of motor unit synchronization following strength training (common input strength index; 0.71 ± 0.41 to 0.67 ± 0.43 pulses/s). Furthermore, motor unit coherence z scores at low (0–10 Hz; 3.9 ± 0.3 before to 4.4 ± 0.4 after) or high (10–30 Hz; 1.7 ± 0.1 before to 1.9 ± 0.1 after) frequencies were not influenced by strength training. These motor unit data indicate that increases in strength following several weeks of training a hand muscle are not accompanied by changes in motor unit synchronization or coherence, suggesting that these features of correlated motor unit activity are not important in the expression of muscle strength.

Abrasion processes in wear and manufacturing

Abrasion by hard particles is responsible for wear in many practical situations, but can also be used constructively in grinding and polishing processes. A brief overview of abrasion is presented, followed by an historical survey of polishing and a discussion of laboratory abrasion test methods.

The relationship between lower body strength and obstructed gait in community-dwelling older adults

OBJECTIVES: To determine the relationship between lower body strength of community-dwelling older adults and the time to negotiate obstructed gait tasks.

DESIGN: A correlational study.

SETTING: The Biomechanics Laboratory, Deakin University, Australia.

PARTICIPANTS: Twenty-nine women and 16 men aged 62 to 88 were recruited using advertisements placed in local newspapers. The participants were independent community dwellers, healthy and functionally mobile.

MEASUREMENTS: Maximal isometric strength of the knee extensors and dynamic strength of the hip extensors, hip flexors, hip adductors, hip abductors, knee extensors, knee flexors, and ankle plantar flexors were assessed. The times to negotiate four obstructed gait tasks at three progressively challenging levels on an obstacle course and to complete the course were recorded. The relationship between strength and the crossing times was explored using linear regression models.

RESULTS: Significant associations between the seven strength measures and the times to negotiate each gait task and to walk the entire course at each level were obtained (r = -0.38 to -0.55; P < .05). In addition, the percentage of the variance explained by strength (R2), consistently increased as a function of the progressively challenging level. This increase was particularly marked for the stepping over task (R2 = 19.3%,25.0%, and 27.2%, for levels 1, 2, and 3, respectively) and the raised surface condition (R2 = 17.1%,21.1%, and 30.8%, for levels 1,2, and 3, respectively) .

CONCLUSION: The findings of the study showed that strength is a critical requirement for obstructed locomotion. That the magnitude of the association increased as a function of the challenging levels suggests that intervention programs aimed at improving strength would potentially be effective in helping community-dwelling older adults negotiate environmental gait challenges.

Effect of fluoride varnish supplemented with sodium trimetaphosphate on enamel erosion and abrasion: An in situ/ex vivo study

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Resistência de união e estabilidade de um sistema adesivo universal à dentina erodida/abrasionada após desproteinização

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Effects of strength and power training on neuromuscular variables in older adults

The purpose of this study was to compare the neuromuscular adaptations produced by strength-training (ST) and power-training (PT) regimens in older individuals. Participants were balanced by quadriceps cross-sectional area (CSA) and leg-press 1-repetition maximum and randomly assigned to an ST group (n = 14; 63.6 +/- 4.0 yr, 79.7 +/- 17.2 kg, and 163.9 +/- 9.8 cm), a PT group (n = 16; 64.9 +/- 3.9 yr. 63.9 +/- 11.9 kg, and 157.4 +/- 7.7 cm), or a control group (n = 13; 63.0 +/- 4.0 yr, 67.2 +/- 10.8 kg, and 159.8 +/- 6.8 cm). ST and PT were equally effective in increasing (a) maximum dynamic and isometric strength (p < .05), (b) increasing quadriceps muscle CSA (p < .05), and (c) decreasing electrical mechanical delay of the vastus lateralis muscle (p < .05). There were no significant changes in neuromuscular activation after training. The novel finding of the current study is that PT seems to be an attractive alternative to regular ST to maintain and improve muscle mass.

Serum free testosterone, leptin and soluble leptin receptor changes in a 6-week strength-training programme

[EN] Strength training is usually associated with a reduction in fat mass and with muscle hypertrophy. The aim of the present study was to examine whether the serum free leptin index (FLI), measured by the molar excess of soluble leptin receptor (sOB-R) over leptin, is increased by 6 weeks of strength training. Eighteen male, physical education students were randomly assigned to two groups: a strength-training (n 12) and a control group (n 6). Body composition (lean body mass and body fat) determined by dual-energy X-ray absorptiometry (DXA), muscle performance and leptin, sOB-R, total testosterone and free testosterone concentrations were determined before and after training. Fat mass was reduced by 1 kg with strength training (P<0.05). Lean body mass of trained extremities was increased by 3% (P<0.05), while the concentration of free testosterone in serum was reduced by 17% (P<0.05) after training. However, despite the reduction in fat mass and free testosterone, serum leptin concentration was not significantly affected by strength training, even after accounting for the differences in body fat. By contrast, for a given fat mass, the sOB-R was increased by 13% (P<0.05) at the end of the strength-training programme, although the molar excess of sOB-R over leptin remained unchanged. Therefore, the quantity of free leptin available to bind to the target tissues was not significantly affected by the short strength-training programme, which elicited a 7% reduction in fat mass.

A model for the erosive wear of rubber at oblique impact angles

A model has been developed to predict the erosive wear behaviour of elastomers under conditions of glancing impact by small hard particles. Previous work has shown the erosive wear mechanism of elastomers under these conditions to be similar in nature to that of abrasive wear by a sharp blade. The model presented here was developed from the model of Southern and Thomas for sliding abrasion, by combining their treatment of the growth of surface cracks with a model for particle impact in which the force - displacement relationship for an idealized flat-ended punch on a semi-infinite elastic solid was assumed. In this way an expression for the erosive wear rate was developed, and compared with experimental measurements of wear rate for natural rubber, styrene - butadiene rubber and a highly crosslinked polybutadiene rubber. Good qualitative agreement was found between the predictions of the model and the experimental measurements. The variation of erosion rate with impact velocity, impact angle, particle size, elastic modulus of the material, coefficient of friction and fatigue properties were all well accounted for. Quantitative agreement was less good, and the effects of erosive particle shape could not be accounted for. The reasons for these discrepancies are discussed. © 1992 IOP Publishing Ltd.

Microstructural analysis of non-woven fabrics using scanning electron microscopy and image processing. Part 2:Application to hydroentangled fabrics

The image analysis techniques developed in Part 1 to study microstructural changes in non-woven fabrics are applied to measure the fibre orientation distribution and fibre length distribution of hydroentangled fabrics. The results are supported by strength and modulus measurements using samples from the same fabrics. It is shown that the techniques developed can successfully be used to assess the degree of entanglement of hydroentangled fabrics regardless of their thickness.

Increasing the wear resistance of molds for injection of glass fiber reinforced plastics

Abrasion by glass fibers during injection molding of fiber reinforced plastics raises new challenges to the wear performance of the molds. In the last few decades, a large number of PVD and CVD coatings have been developed with the aim of minimizing abrasion problems. In this work, two different coatings were tested in order to increase the wear resistance of the surface of a mold used for glass fiber reinforced plastics: TiAlSiN and CrN/CrCN/DLC. TiAlSiN was deposited as a graded monolayer coating while CrN/CrCN/DLC was a nanostructured coating consisting of three distinct layers. Both coatings were produced by PVD unbalanced magnetron sputtering and were characterized using scanning electron microscopy (SEM) provided with energy dispersive spectroscopy (EDS), atomic force microscopy (AFM), micro hardness (MH) and scratch test analysis. Coating morphology, thickness, roughness, chemical composition and structure, hardness and adhesion to the substrate were investigated. Wear resistance was characterized through industrial tests with coated samples and an uncoated reference sample inserted in a feed channel of a plastic injection mold working with 30 wt.% glass fiber reinforced polypropylene. Results after 45,000 injection cycles indicate that the wear resistance of the mold was increased by a factor of 25 and 58, by the TiAlSiN and CrN/CrCN/DLC coatings, respectively, over the uncoated mold steel.

Unfulfilled rehabilitation needs and dissatisfaction with care 12 months after a stroke : an explorative observational study

BACKGROUND: People who have suffered a stroke commonly report unfulfilled need for rehabilitation. Using a model of patient satisfaction, we examined characteristics in individuals that at 3 months after stroke predicted, or at 12 months were associated with unmet need for rehabilitation or dissatisfaction with health care services at 12 months after stroke. METHODS: The participants (n = 175) received care at the stroke units at the Karolinska University Hospital, Sweden. The dependent variables "unfulfilled needs for rehabilitation" and "dissatisfaction with care" were collected using a questionnaire. Stroke severity, domains of the Stroke Impact Scale (SIS), the Sense of Coherence scale (SOC) and socio demographic factors were used as independent variables in four logistic regression analyses. RESULTS: Unfulfilled needs for rehabilitation at 12 months were predicted by strength (SIS) (odds ratio (OR) 7.05) at three months, and associated with hand function (SIS) (OR 4.38) and poor self-rated recovery (SIS) (OR 2.46) at 12 months. Dissatisfaction with care was predicted by SOC (OR 4.18) and participation (SIS) (OR 3.78), and associated with SOC (OR 3.63) and strength (SIS) (OR 3.08). CONCLUSIONS: Thirty-three percent of the participants reported unmet needs for rehabilitation and fourteen percent were dissatisfied with the care received. In order to attend to rehabilitation needs when they arise, rehabilitation services may need to be more flexible in terms of when rehabilitation is provided. Long term services with scheduled re-assessments and with more emphasis on understanding the experiences of both the patients and their social networks might better be able to provide services that attend to patients' needs and aid peoples' reorientation; this would apply particularly to those with poor coping capacity.

Older adults' neuromuscular adaptations to resistence training and effects on challenging gait tasks

Community locomotion is threatened when older individuals are required to negotiate obstacles, which place considerable stress on the musculoskeletal system. The vulnerability of older adults during challenging locomotor tasks is further compromised by age-related strength decline and muscle atrophy. The first study in this investigation determined the relationship between the major muscle groups of the lower body and challenging locomotor tasks commonly found in the community environment of older adults. Twenty-nine females and sixteen males aged between 62 and 88 years old (68.2 ±6.5) were tested for the maximal voluntary contraction (MVC) strength of the knee extensors and 1-RM for the hip extensors, flexors, adductors, abductors, knee extensors and flexors and ankle plantar flexors. Temporal measurements of an obstacle course comprising four gait tasks set at three challenging levels were taken. The relationship between strength and the obstacle course dependent measures was explored using linear regression models. Significant associations (p≤0.05) between all the strength measures and the gait performances were found. The correlation values between strength and obstructed gait (r = 0.356-0.554) and the percentage of the variance explained by strength (R2 = 13%-31%), increased as a function of the challenging levels, especially for the stepping over and on and off conditions. While the difficulty of community older adults to negotiate obstacles cannot be attributed to a single causal pathway, the findings of the first study showed that strength is a critical requirement. That the magnitude of the association increased as a function of the challenging levels, suggests that interventions aimed at improving strength would potentially be effective in helping community older adults to negotiate environmental gait challenges. In view of the findings of the first study, a second investigation determined the effectiveness of a progressive resistance-training program on obstructed gait tasks measured under specific laboratory conditions and on an obstacle course mimicking a number of environmental challenges. The time courses of strength gains and neuromuscular mechanisms underpinning the exercise-induced strength improvements in community-dwelling older adults were also investigated. The obstructed gait conditions included stepping over an obstacle, on and off a raised surface, across an obstacle and foot targeting. Forty-three community-living adults with a mean age of 68 years (control =14 and experimental=29) completed a 24-week progressive resistance training program designed to improve strength and induce hypertrophy in the major muscles of the lower body. Specific laboratory gait kinetics and kinematics and temporal measures taken on the obstacle course were measured. Lean tissue mass and muscle activation of the lower body muscle groups were assessed. The MVC strength of the knee extensors and 1-RM of the hip extension, hip flexion, knee extension, knee flexion and ankle plantar flexion were measured. A 25% increase on the MVC of the knee extensors (p≤0.05) was reported in the training group. Gains ranging between 197% and 285% were recorded for the 1-RM exercises in the trained subjects with significant improvements found throughout the study (p≤0.05). The exercise-induced strength gains were mediated by hypertrophic and neural factors as shown by 8.7% and 27.7% increases (p≤0.05) in lean tissue mass and integrated electromyographic activity, respectively. Strength gains were accompanied by increases in crossing velocity, stride length and reductions in stride duration, stance and swing time for all gait tasks except for the foot targeting condition. Specific kinematic variables associated with safe obstacle traverse such as vertical obstacle heel clearance, limb flexion, horizontal foot placements prior to and at post obstacle crossing and landing velocities resulted in an improved crossing strategy in the experimental subjects. Significant increases in the vertical and anterior-posterior ground reaction forces accompanied the changes in the gait variables. While further long-term prospective studies of falls rates would be needed to confirm the benefits of lower limb enhanced strength, the findings of the present study provide conclusive evidence of significant improvements to gait efficiency associated with a systematic resistance-training program. It appears, however, that enhanced lower body strength has limited effects on gait tasks involving a dynamic balance component. In addition, due to the larger strength-induced increases in voluntary activation of the leg muscle compared to relatively smaller gains in lean tissue mass, neural adaptations appear to play a greater contributing role in explaining strength gains during the current resistance training protocol.

Análise de falhas em martelos oscilantes dos desfibradores da indústria sucroalcooleira da Região Norte-Nordeste

The failure of materials is always an unwelcome event for several reasons: human lives are put in danger, economic losses, and interference in the availability of products and services. Although the causes of failures and behaviour of materials can be known, the prevention of such a condition is difficult to be guaranteed. Among the failures, wear abrasion by the low voltage is the kind of failure that occurs in more equipment and parts industry. The Plants Sucroalcooleiras suffer significant losses because of such attrition, this fact that motivated their choice for the development of this work. For both, were considered failures in the swing hammers desfibradores stopped soon after the exchange provided in accordance with tonnage of cane processed, then were analyzed by the level of wear testing of rubber wheel defined by the standard ASTM G65-91.The failures were classified as to the origin of the cause and mechanism, moreover, were prepared with samples of welding procedures according to ASME code, sec. IX as well, using the technique of thermal spraying to analyze the performance of these materials produced in laboratories, and compares them with the solder used in the plant. It was observed that the bodies-of-proof prepared by the procedure described as welding, and the thermal spraying the results of losing weight have been minimized significantly compared to the preparations in the plant. This is because the use of techniques more appropriate and more controlled conditions of the parameters of welding. As for the thermal spraying, this technique has presented a satisfactory result, but requires the use of these coatings in the best condition for real affirmation of the results