A Fully Integrated 900-MHz Passive RFID Transponder Front End With Novel Zero-Threshold RF-DC Rectifier

This paper presents a fully integrated CMOS analog front end for a passive 900-MHz radio-frequency identification (RFID) transponder. The power supply in this front end is generated from the received RF electromagnetic energy by using an RF-dc voltage rectifier. In order to improve the compatibility with standard CMOS technology, Schottky diodes in conventional RF-dc rectifiers are replaced by diode-connected MOS transistors with zero threshold. Meanwhile, theoretical analyses for the proposed rectifier are provided and verified by both simulation and measurement results. The design considerations of the pulsewidth-modulation (PWM) demodulator and the backscatter modulator in the front end are also discussed for low-power applications. The proposed front end is implemented in a 0.35-mu m 2P4M CMOS technology. The whole chip occupies a die area of 490 x 780 mu m(2) and consumes only 2.1 mu W in reading mode under a self-generated 1.5-V supply voltage. The measurement results show that the proposed rectifier can properly operate with a - 14.7-dBm input RF power at a power conversion efficiency of 13.0%. In the proposed RFID applications, this sensitivity corresponds to 10.88-m communication distance at 4-W equivalent isotropically radiated power from a reader base station.

A microwave metamaterial with integrated power harvesting functionality

We present the design and experimental implementation of a power harvesting metamaterial. A maximum of 36.8% of the incident power from a 900 MHz signal is experimentally rectified by an array of metamaterial unit cells. We demonstrate that the maximum harvested power occurs for a resistive load close to 70 Ω in both simulation and experiment. The power harvesting metamaterial is an example of a functional metamaterial that may be suitable for a wide variety of applications that require power delivery to any active components integrated into the metamaterial. © 2013 AIP Publishing LLC.

Design strategies for dual-band class-e power amplifier using composite right/left-handed transmission lines

In this article we propose a technique for dual-band Class-E power amplifier design using composite right/left-handed transmission lines, CRLH TLs. Design equations are presented and design procedures are elaborated. Because of the nonlinear phase dispersion characteristic of CRLH TLs, the single previous attempt at applying this method to dual bond Class-E amplifier design was not sufficient to simultaneously satisfy, the minimum requirement of Class-E impedances at both the fundamental and the second harmonic frequencies. This article rectifies this situation. A design example illustrating the synthesis procedure for a 0.5W-5V dual band Class-E amplifier circuit simultaneously operated at 900 MHz and 2.4 GHz is given and compared with ADS simulation.

Design of a wideband conformal array antenna system with beamforming and null steering, for application in a DVB-T based passive radar

The use of radars in detecting low flying, small targets is being explored for several decades now. However radar with counter-stealth abilities namely the passive, multistatic, low frequency radars are in the focus recently. Passive radar that uses Digital Video Broadcast Terrestrial (DVB-T) signals as illuminator of opportunity is a major contender in this area. A DVB-T based passive radar requires the development of an antenna array that performs satisfactorily over the entire DVB-T band. At Fraunhofer FHR, there is currently a need for an array antenna to be designed for operation over the 450-900 MHz range with wideband beamforming and null steering capabilities. This would add to the ability of the passive radar in detecting covert targets and would improve the performance of the system. The array should require no mechanical adjustments to inter-element spacing to correspond to the DVB-T carrier frequency used for any particular measurement. Such an array would have an increased flexibility of operation in different environment or locations.

The design of such an array antenna and the applied techniques for wideband beamforming and null steering are presented in the thesis. The interaction between the inter-element spacing, the grating lobes and the mutual couplings had to be carefully studied and an optimal solution was to be reached at that meets all the specifications of the antenna array for wideband applications. Directional beams, nulls along interference directions, low sidelobe levels, polarization aspects and operation along a wide bandwidth of 450-900 MHz were some of the key considerations.

Design of a Compact Multiband Microstrip Antenna

A compact microstrip multiband antenna on a modified ground plane which can operate over the bands starting from 900 MHz to 5.35 GHz which includes the GSM (880-960) GPS (1568-1592 MHz), DCS (1710-1880 MHz), and PCS (1850- 1990 MHz). UMTS (1920-2170 MHz), IEEE 802.11 b/g (2400- 2484) and WLAN IEEE 802.11a band (5.15-5.35) is reported in this paper. The overall dimension of the antenna is 33 x 33 mm2 including the top patch with a dimension 22 x 22 mm2. The experimental results of the antenna are presented in this paper. The results confirm that the antenna exhibits wide band characteristics and covers 7 bands of operation

Compact Uniplanar Antenna for Multiband Applications

A dual band RFID applications in 800 900 MHz and 2400 MHz band is presented. The Asymmetric Coplanar Strip (ACS) fed antenna consists of inverted L shaped monopole with a capacitive loading to provide necessary impedance matching and current distribution. The antenna has wide bandwidth from 790 MHz tol050 MHz and from 2350 MHz to 2640 MHz coving the RFID UHF and Microwave frequencies. The uniplanar antenna having overall dimensions of 48 mm x 14 mm is printed on one side of a substrate of dielectric constant 4.4 and height 1.6 mm.

Modelo 2,5D de predição de propagação para ambientes interiores utilizando o método do traçado de raios

A 2.5D ray-tracing propagation model is proposed to predict radio loss in indoor environment. Specifically, we opted for the Shooting and Bouncing Rays (SBR) method, together with the Geometrieal Theory of Diffrartion (GTD). Besides the line-of-sight propagation (LOS), we consider that the radio waves may experience reflection, refraction, and diffraction (NLOS). In the Shooting and Bouncing Rays (SBR) method, the transmitter antenna launches a bundle of rays that may or may not reach the receiver. Considering the transmitting antenna as a point, the rays will start to launch from this position and can reach the receiver either directly or after reflections, refractions, diffractions, or even after any combination of the previous effects. To model the environment, a database is built to record geometrical characteristics and information on the constituent materials of the scenario. The database works independently of the simulation program, allowing robustness and flexibility to model other seenarios. Each propagation mechanism is treated separately. In line-of-sight propagation, the main contribution to the received signal comes from the direct ray, while reflected, refracted, and diffracted signal dominate when the line-of-sight is blocked. For this case, the transmitted signal reaches the receiver through more than one path, resulting in a multipath fading. The transmitting channel of a mobile system is simulated by moving either the transmitter or the receiver around the environment. The validity of the method is verified through simulations and measurements. The computed path losses are compared with the measured values at 1.8 GHz ftequency. The results were obtained for the main corridor and room classes adjacent to it. A reasonable agreement is observed. The numerical predictions are also compared with published data at 900 MHz and 2.44 GHz frequencies showing good convergence

Proposta metodológica para o imageamento digital e modelagem virtual 3d de um bloco de rochas travertinas

In this paper we present the methodological procedures involved in the digital imaging in mesoscale of a block of travertines rock of quaternary age, originating from the city of Acquasanta, located in the Apennines, Italy. This rocky block, called T-Block, was stored in the courtyard of the Laboratório Experimental Petróleo "Kelsen Valente" (LabPetro), of Universidade Estadual de Campinas (UNICAMP), so that from it were performed Scientific studies, mainly for research groups universities and research centers working in brazilian areas of reservoir characterization and 3D digital imaging. The purpose of this work is the development of a Model Solid Digital, from the use of non-invasive techniques of digital 3D imaging of internal and external surfaces of the T-Block. For the imaging of the external surfaces technology has been used LIDAR (Light Detection and Range) and the imaging surface Interior was done using Ground Penetrating Radar (GPR), moreover, profiles were obtained with a Gamma Ray Gamae-spectômetro laptop. The goal of 3D digital imaging involved the identification and parameterization of surface geological and sedimentary facies that could represent heterogeneities depositional mesoscale, based on study of a block rocky with dimensions of approximately 1.60 m x 1.60 m x 2.70 m. The data acquired by means of terrestrial laser scanner made available georeferenced spatial information of the surface of the block (X, Y, Z), and varying the intensity values of the return laser beam and high resolution RGB data (3 mm x 3 mm), total points acquired 28,505,106. This information was used as an aid in the interpretation of radargrams and are ready to be displayed in rooms virtual reality. With the GPR was obtained 15 profiles of 2.3 m and 2 3D grids, each with 24 sections horizontal of 1.3 and 14 m vertical sections of 2.3 m, both the Antenna 900 MHz to about 2600 MHz antenna. Finally, the use of GPR associated with Laser Scanner enabled the identification and 3D mapping of 3 different radarfácies which were correlated with three sedimentary facies as had been defined at the outset. The 6 profiles showed gamma a low amplitude variation in the values of radioactivity. This is likely due to the fact of the sedimentary layers profiled have the same mineralogical composition, being composed by carbonate sediments, with no clay in siliciclastic pellitic layers or other mineral carrier elements radioactive

Automated NMR structure determination and disulfide bond identification of the myotoxin crotamine from Crotalus durissus terrificus

Crotamine is one of four major components of the venom of the South American rattlesnake Crotalus durissus terrificus. Similar to its counterparts in the family of the myotoxins, it induces myonecrosis of skeletal muscle cells. This paper describes a new NMR structure determination of crotamine in aqueous solution at pH 5.8 and 20 degrees C, using standard homonuclear (1)H NMR spectroscopy at 900 MHz and the automated structure calculation software ATNOS/CANDID/DYANA. The automatic NOESY spectral analysis included the identification of a most likely combination of the six cysteines into three disulfide bonds, i.e. Cys4-Cys36, Cys11-Cys30 and Cys18-Cys37; thereby a generally applicable new computational protocol is introduced to determine unknown disulfide bond connectivities in globular proteins. A previous NMR structure determination was thus confirmed and the structure refined. Crotamine contains an alpha-helix with residues 1-7 and a two-stranded anti-parallel beta-sheet with residues 9-13 and 34-38 as the only regular secondary structures. These are connected with each other and the remainder of the polypeptide chain by the three disulfide bonds, which also form part of a central hydrophobic core. A single conformation was observed, with Pro13 and Pro21 in the trans and Pro20 in the cis-form. The global fold and the cysteine-pairing pattern of crotamine are similar to the beta-defensin fold, although the two proteins have low sequence homology, and display different biological activities. (c) 2005 Elsevier Ltd. All rights reserved.

Differential mixer with NMOS/PMOS stack at switching stage

This paper proposes a novel differential mixer topology. The traditional stage of switching is replaced by a stack of NMOS and PMOS transistors combined. A design is given of a 900 MHz down-conversion mixer using a 0.35 μm CMOS process. Comparison with conventional mixer shows that the topology leads to a better performance in terms of conversion gain and linearity. ©2012 IEEE.

S-0 and S-1 State Structure, Methyl Torsional Barrier Heights, and Fast Intersystem Crossing Dynamics of 5-Methyl-2-hydroxypyrimidine

We report the analysis of the SI So rotational band contours of jet-cooled 5-methyl-2-hydroxypyrimidine (5M2HP), the enol form of deoxythymine. Unlike thymine, which exhibits a structureless spectrum, the vibronic spectrum of 5M2HP is well structured, allowing us to determine the rotational constants and the methyl group torsional barriers in the S-0 and S-1 states. The 0(0)(0), 6a(0)(1), 6b(0)(1), and 14(0)(1) band contours were measured at 900 MHz (0.03 cm(-1)) resolution using mass-specific two-color resonant two-photon ionization (2C-R2PI) spectroscopy. All four bands are polarized perpendicular to the pyrimidine plane (>90% c type), identifying the S-1 <- S-0 excitation of 5M2HP as a 1n pi* transition. All contours exhibit two methyl rotor subbands that arise from the lowest 5-methyl torsional states 0A '' and 1E ''. The S-0 and S-1 state torsional barriers were extracted from fits to the torsional subbands. The 3-fold barriers are V-3 '' = 13 cm(-1) and V3' = SI cm(-1); the 6-fold barrier contributions V-6 '' and V-6' are in the range of 2-3 cm(-1) and are positive in both states. The changes of A, B, and C rotational constants upon S-1 <- S-0 excitation were extracted from the contours and reflect an "anti-quinoidal" distortion. The 0(0)(0) contour can only be simulated if a 3 GHz Lorentzian line shape is included, which implies that the S-1(1n pi*) lifetime is similar to 55 ps. For the 6a(0)(1) and 6b(0)(1) bands, the Lorentzian component increases to 5.5 GHz, reflecting a lifetime decrease to similar to 30 ps. The short lifetimes are consistent with the absence of fluorescence from the 1n pi* state. Combining these measurements with the previous observation of efficient intersystem crossing (ISC) from the Si state to a long-lived T-1((3)n pi*) state that lies similar to 2200 cm(-1) below [S. Lobsiger, S. et al. Phys. Chem. Chem. Phys. 2010, 12, 5032] implies that the broadening arises from fast intersystem crossing with k(ISC) approximate to 2 x 10(10) s(-1). In comparison to 5-methylpyrimidine, the ISC rate is enhanced by at least 10 000 by the additional hydroxy group in position 2.

Influence of an electromagnetic field on high dilutions measured by ultraviolet light spectroscopy

Background: High dilutions of various starting materials, e.g. copper sulfate, Hypericum perforatum and sulfur, showed significant differences from controls and amongst different dilution levels in ultraviolet light (UV) transmission [1,2]. Exposure of high dilutions to external physical factors such as UV light or elevated temperature (37°C) also yielded significantly different UV transmissions compared to unexposed dilutions [2,3]. In a study with highland frogs it was shown that animals incubated with thyroxine 30c but not with thyroxine 30c exposed to electromagnetic fields (EMFs) of a microwave oven or mobile phone metamorphosed more slowly than control animals [4]. Aims: The aim was to test whether the EMF of a mobile phone influences the UV absorbance of dilutions of quartz and Atropa belladonna (AB). Methodology: Commercially available dilutions of 6x, 12x, 15x, 30x in H2O and 19% ethanol of quartz (SiO2) and of 4x, 6x, 12x, 15x, 30x in H2O and 19% ethanol of AB were used in the experiments (Weleda AG, Arlesheim, Switzerland). Four samples of each dilution were exposed to the EMF of a mobile phone (Philips, Savvy Dual Band) at 900 MHz with an output of 2 W for 3 h, while control samples (4 of each dilution) were kept in a separate room. Absorbance of the samples in the UV range (from 190 to 340 nm) was measured in a randomized order with a Shimadzu UV-1800 spectrophotometer equipped with an auto sampler. In total 5 separate measurement days will be carried out for quartz and for AB dilutions. The average absorbance from 200 to 340 nm and from 200 to 240 nm was compared among dilution levels using a Kruskal-Wallis test and between exposed and unexposed samples using a Mann-Whitney-U test. Results: Preliminary results after 2 measurement days indicated that for quartz the absorbance of the various dilution levels was different from each other (except 12x and 15x), and that samples exposed to an EMF did not show a difference in UV absorbance from unexposed samples. Preliminary results after one measurement day indicated that for AB the absorbance of the various dilution levels was different from each other. The samples exposed to an EMF did not show a difference in UV absorbance from unexposed samples (except 4x in the range from 200 – 240 nm). Conclusions: These results suggest that exposure of high dilutions of quartz and AB to a mobile phone EMF as used here does not alter UV absorbance of these dilutions. The final results will show whether this holds true.

Comunicaciones móviles en entornos complejos: Planificación de redes LTE.

En este proyecto se estudiarán las interferencias en el canal adyacente de los sistemas celulares, ubicados en las bandas de 900 y 1800 MHz. Para esto, se analizarán medidas de interferencia entre LTE y otros sistemas de comunicación celular. En el primer capítulo, se dará una breve descripción de los principales parámetros empleados en los distintos estándares de comunicaciones móviles, que operan en las bandas de frecuencia de interés. En el segundo, se van a explicar los distintos tipos de interferencias existentes entre sistemas celulares. También se verán las diferentes técnicas para reducir dichas interferencias, como por ejemplo, la de control de potencia y la de coordinación de interferencia entre celdas. Además, se explicarán los parámetros para determinar la interferencia en el canal adyacente, como son el ACLR, ACS y ACIR. Para finalizar se resumirán las principales características de los sistemas LTE y WiMAX. En el tercer capítulo, se estudiarán las interferencias que genera principalmente LTE a los otros sistemas celulares, mediante los parámetros que miden la interferencia en el canal adyacente explicados en el capítulo dos. Además, se determinará la separación en frecuencia que debe existir entre los canales para que los sistemas puedan coexistir. El capítulo cuatro se basa en la simulación de tres escenarios de interferencia entre dichos sistemas. Para esto, se utilizará el software de simulación de propagación radio, denominado Radio Plan. Con estas simulaciones se cuantificarán las pérdidas de rendimiento que sufren los sistemas interferidos. Por último, en el capítulo cinco se resumirán las conclusiones a las que se llegaron después de simular los diferentes escenarios de interferencia. SUMMARY In this project an adjacent channel interference study for cellular systems, allocated within 900 MHz and 1800 MHz bands will be performed. For this aim a set of measurements will be analyzed. In the first chapter, a brief explanation of the main parameters used in different mobile communications standards that operate in the frequency bands of interest, will be given. In the second chapter, different types of interference between cellular systems will be explained, as well as different techniques to reduce such interference. For example, power control and interference coordination between cells, will be shown. Furthermore, the parameters to determine the adjacent-channel interference, such as the ACLR, ACS and ACIR will be overviewed. Finally, the main features of LTE and WiMAX systems will be summarized. In the third chapter, the interference generated by the other mainly LTE cellular systems via parameters that measure the adjacent channel interference explained in chapter two will be studied. Also, the frequency separation that must exist between the channels so that the systems can coexist will be determined. The fourth chapter is based on the simulation of three scenarios of interference between these systems. For this purpose, a radio propagation simulation software package Radio Plan will be used. These simulations will quantify performance losses suffered by systems that interfered. Finally, in chapter five the conclusions about the results of simulations of interference in different scenarios will be presented.

Measurements and modelling of radio propagation in subway tunnels

The work presented in this article is focused on the RF measurement campaign carried out in several subway tunnels in Metro Madrid (Spain). Most common segments such as straight lines, curves and passing through station as well as other unique scenarios in metropolitan lines were the selected locations during this campaign. Measurements were conducted in tunnels of diverse cross section shapes and taken at three frequency bands: 900 MHz, 2.4GHz and 5.7 GHz for both horizontal and vertical polarization.

Análisis prospectivo del despliegue de redes de comunicaciones móviles LTE en nuevas bandas de frecuencia mediante el desarrollo de modelos tecnoeconómicos

El estándar LTE se ha posicionado como una de las claves para que los operadores de telecomunicación puedan abordar de manera eficiente en costes el crecimiento de la demanda de tráfico móvil que se prevé para los próximos años, al ser una tecnología más escalable en el núcleo de la red y más flexible en la interfaz radio que sus predecesoras. En este sentido, es necesario también que los reguladores garanticen un acceso al espectro radioeléctrico adecuado, equitativo y no discriminatorio, que permita un entorno estable para el despliegue de redes de comunicaciones móviles avanzadas. Además de la flexibilización del marco regulador del espectro radioeléctrico en Europa, que ha permitido el despliegue de nuevas tecnologías en las bandas de frecuencia históricas de GSM, se ha puesto a disposición espectro adicional para sistemas IMT en nuevas bandas de frecuencia, lo que ha planteando a su vez nuevos retos para la tecnología y la regulación. La fragmentación del espectro disponible para comunicaciones móviles ha impulsado el desarrollo de técnicas de agregación de portadoras en las nuevas versiones del estándar LTE, que permiten explotar mejor los recursos radio en su conjunto. No obstante, el espectro inferior a 1 GHz sigue siendo escaso, ya que el tráfico móvil aumenta y la banda de 900 MHz aún se utiliza para servicios GSM, lo que no ha conseguido sino agravar la disputa entre los servicios de radiodifusión terrestre y de comunicaciones móviles por la parte superior de la banda UHF. En concreto, la banda de 700 MHz se perfila como una de las próximas para aumentar el espectro disponible para los servicios en movilidad, si bien su liberación por parte de las actuales redes de Televisión Digital Terrestre presenta no pocas dificultades en los Estados miembros en los que ésta es la principal plataforma audiovisual de acceso gratuito, abriendo un debate sobre el modelo audiovisual a largo plazo en Europa. Por otro lado, las políticas públicas de promoción del acceso a la banda ancha rápida y ultrarrápida de la presente década han establecido objetivos ambiciosos para el año 2020, tanto en el ámbito europeo como en los diferentes Estados miembros. La universalización del acceso a redes de banda ancha de al menos 30 Mbps constituye uno de los principales retos. Las expectativas generadas por la tecnología LTE y la puesta a disposición de nuevas bandas de frecuencia hace posible que los servicios de acceso fijo inalámbrico adquieran especial relevancia ante los objetivos de política pública establecidos que, como ha sido reconocido en diversas ocasiones, no podrán lograrse sino con un compendio de diferente tecnologías. Para esta Tesis Doctoral se han desarrollado una serie modelos tecnoeconómicos con el objetivo de realizar un análisis prospectivo que evalúa tres casos de especial relevancia en el despliegue de redes LTE: en primer lugar, la valoración económica de la banda de 700 MHz; en segundo lugar, la evaluación de modelos de negocio y reducción de costes considerando tecnologías femtocelulares; y finalmente, la viabilidad de las redes LTE de acceso fijo inalámbrico para el cierre de la brecha digital en el acceso a la banda ancha de 30 Mbps. En relación con la aplicación del análisis tecnoeconómico para la valoración del espectro de 700 MHz, los resultados obtenidos ponen de manifiesto dos cuestiones fundamentales. En primer lugar, la necesidad de asignar a los operadores más espectro para satisfacer las previsiones de demanda de tráfico móvil a medio plazo. En segundo, existe una diferencia notable en los costes de despliegue de una red LTE cuando se dispone de espectro en frecuencias inferiores a 1 GHz y cuando no, pero esta diferencia de costes disminuye a medida que se añade nuevo espectro sub-1GHz. De esta manera, la atribución de la banda de 700 MHz a servicios de comunicaciones móviles supone una reducción relevante en los costes de despliegue si el operador no dispone de espectro en la banda de 800 MHz, pero no así si ya dispone de espectro en bandas bajas para el despliegue. En este sentido, puede concluirse que el precio que los operadores estarán dispuestos a pagar por el espectro de la banda de 700 MHz dependerá de si ya tienen disponible espectro en la banda de 800 MHz. Sin embargo, dado que la competencia por ese espectro será menor, los ingresos esperables en las licitaciones de esta nueva banda serán en general menores, a pesar de que para algunos operadores este espectro sería tan valioso como el de 800 MHz. En segundo lugar, en relación con el despliegue de femtoceldas pueden extraerse algunas conclusiones en términos de ahorro de costes de despliegue y también de cara a la viabilidad de los modelos de negocio que posibilitan. El ahorro que supone la introducción de femtoceldas en el despliegue de una red LTE frente al caso de un despliegue exclusivamente macrocelular se ha demostrado que es mayor cuanto menor es el ancho de banda disponible para la red macrocelular. En esta línea, para un operador convergente el despliegue de femtoceldas tiene sentido económico si el ancho de banda disponible es escaso (en torno a 2x10 MHz), que, en el caso de España, puede reflejar el caso de los operadores del segmento fijo que son nuevos entrantes en el móvil. Por otro lado, los modelos de acceso abierto son interesantes para operadores exclusivamente móviles, porque consiguen flexibilizar los costes sustituyendo estaciones base macrocelulares por el despliegue de femtoceldas, pero necesitan desplegarse en zonas con una densidad de población relativamente elevada para que éstas descarguen tráfico de varios usuarios de la red macrocelular simultáneamente. No obstante, las femtoceldas son beneficiosas en todo caso si es el usuario quien asume los costes de la femtocelda y el backhaul, lo que sólo parece probable si se integran en el modelo de negocio de comercialización de nuevos servicios. Por tanto, el despliegue de femtoceldas en buena parte de la casuística estudiada sólo tiene sentido si consiguen aumentar los ingresos por usuario comercializando servicios de valor añadido que necesiten calidad de servicio garantizada y exploten a la vez de esa forma su principal ventaja competitiva respecto a la tecnología WiFi. Finalmente, en relación con el papel de la tecnología LTE para la provisión de servicios de acceso fijo inalámbrico para la banda ancha de 30 Mbps, se ha desarrollado un modelo TD-LTE y mediante la metodología de análisis tecnoeconómico se ha realizado un estudio prospectivo para el caso de España. Los resultados obtenidos preciden una huella de cobertura de FTTH del 74% para 2020, y demuestran que una red TD-LTE en la banda de 3,5 GHz resulta viable para aumentar la cobertura de servicios de 30 Mbps en 14 puntos porcentuales. Junto con la consideración de la cobertura de otras redes, la cobertura de 30 Mbps de acuerdo a la viabilidad de los despliegues alcanzaría el 95% en España en el año 2020. Como resumen, los resultados obtenidos muestran en todos los casos la capacidad de la tecnología LTE para afrontar nuevos desafíos en relación con el aumento del tráfico móvil, especialmente crítico en las zonas más urbanas, y el cierre de la brecha digital en el acceso a la banda ancha rápida en las zonas más rurales. ABSTRACT The LTE standard has been pointed out as one of the keys for telecom operators to address the demand growth in mobile traffic foreseen for the next years in a cost-efficient way, since its core network is more scalable and its radio interface more flexible than those of its predecessor technologies. On the other hand, regulators need to guarantee an adequate, equitable and non-discriminatory access to radio spectrum, which enable a favorable environment for the deployment of advanced mobile communication networks. Despite the reform of the spectrum regulatory framework in Europe, which allowed for the deployment of new technologies in the historic GSM bands, additional spectrum has been allocated to IMT systems in new frequency bands, what in turn has set out new challenges for technology and regulation. The current fragmentation of available spectrum in very different frequency bands has boosted the development of carrier aggregation techniques in most recent releases of the LTE standard, which permit a better exploitation of radio resources as a whole. Nonetheless, spectrum below 1 GHz is still scarce for mobile networks, since mobile traffic increases at a more rapid pace than spectral efficiency and spectrum resources. The 900 MHz frequency band is still being used for GSM services, what has worsen the dispute between mobile communication services and terrestrial broadcasting services for the upper part of the UHF band. Concretely, the 700 MHz frequency band has been pointed out as one of the next bands to be allocated to mobile in order to increase available spectrum. However, its release by current Digital Terrestrial Television networks is challenging in Member States where it constitutes the main free access audiovisual platform, opening up a new debate around the audiovisual model in the long term in Europe. On the other hand, public policies of the present decade to promote fast and ultrafast broadband access has established very ambitious objectives for the year 2020, both at European and national levels. Universalization of 30 Mbps broadband access networks constitutes one of the main challenges. Expectations raised by LTE technology and the allocation of new frequency bands has lead fixed wireless access (FWA) services to acquire special relevance in light of public policy objectives, which will not be met but with a compendium of different technologies, as different involved stakeholders have acknowledged. This PhD Dissertation develops techno-economic models to carry out a prospective analysis for three cases of special relevance in LTE networks’ deployment: the spectrum pricing of the 700 MHz frequency band, an assessment of new business models and cost reduction considering femtocell technologies, and the feasibility of LTE fixed wireless access networks to close the 30 Mbps broadband access gap in rural areas. In the first place and regarding the application of techno-economic analysis for 700 MHz spectrum pricing, obtained results reveal two core issues. First of all, the need to allocate more spectrum for operators in order to fulfill mobile traffic demand in the mid-term. Secondly, there is a substantial difference in deployment costs for a LTE network when there is sub-1GHz spectrum available and when there is not, but this difference decreases as additional sub-1GHz spectrum is added. Thus, the allocation of 700 MHz band to mobile communication services would cause a relevant reduction in deployment costs if the operator does not count on spectrum in the 800 MHz, but not if it already has been assigned spectrum in low frequencies for the deployment. In this regard, the price operators will be willing to pay for 700 MHz spectrum will depend on them having already spectrum in the 800 MHz frequency band or not. However, since competition for the new spectrum will not be so strong, expected incomes from 700 MHz spectrum awards will be generally lower than those from the digital dividend, despite this spectrum being as valuable as 800 MHz spectrum for some operators. In the second place, regarding femtocell deployment, some conclusions can be drawn in terms of deployment cost savings and also with reference to the business model they enable. Savings provided by a joint macro-femto LTE network as compared to an exclusively macrocellular deployment increase as the available bandwidth for the macrocells decreases. Therefore, for a convergent operator the deployment of femtocells can only have economic sense if the available bandwidth is scarce (around 2x10 MHz), which might be the case of fix market operators which are new entrant in mobile market. Besides, open access models are interesting for exclusively mobile operators, since they make costs more flexible by substituting macrocell base stations by femtocells, but they need to be deployed relatively densely populated areas so that they can offload traffic from several macrocell users simultaneously. Nonetheless, femtocells are beneficial in all cases if the user assumes both femtocell and backhaul costs, which only seems probable if they are integrated in a business model commercializing new services. Therefore, in many of the cases analyzed femtocell deployment only makes sense if they increase revenues per user through new added value services which need from guaranteed quality of service, thus exploiting its main competitive advantage compared to WiFi. Finally, regarding the role of LTE technology in the provision of fixed wireless access services for 30 Mbps broadband, a TD-LTE model has been developed and a prospective study has been carried out through techno-economic methodology for the Spanish case. Obtained results foresee a FTTH coverage footprint of 74% households for 2020, and prove that a TD-LTE network in the 3.5 GHz band results feasible to increase 30 Mbps service coverage in additional 14 percentage points. To sum up, obtained results show LTE technology capability to address new challenges regarding both mobile traffic growth, particularly critical in urban zones, and the current digital divide in fast broadband access in most rural zones.