Polymerization of 1,3-butadiene with VO(P-204)(2) and VO(P-507)(2) activated by alkylaluminum

The oxovanadium phosphonates (VO(P-204)(2) and VO(P-507)(2)) activated by various alkylaluminums (AlR3, R = Et, i-Bu, n-Oct; HAIR(2), R = Et, i-Bu) were examined in butadiene (Bd) polymerization. Both VO(P-204)(2) and VO(P-507)(2) showed higher activity than those of classical vanadium-based catalysts (e.g. VOCl3, V(acac)(3)). Among the examined catalysts, the VO(P-204)(2)/Al(Oct)(3) system (I) revealed the highest catalytic activity, giving the poly(Bd) bearing M-n of 3.76 x 10(4) g/mol, and M-w/M-n ratio of 2.9, when the [Al]/[V] molar ratio was 4.0 at 40 degrees C. The polymerization rate for I is of the first order with respect to the concentration of monomer. High thermal stability of I was found, since a fairly good catalytic activity was achieved even at 70 degrees C (polymer yield > 33%); the M-n value and M-w/M-n, ratio were independent of polymerization temperature in the range of 40-70 degrees C. By IR and DSC, the poly(Bd)s obtained had high 1,2-unit content (> 65%) with atactic configuration. The 1,2-unit content of the polymers obtained by I was nearly unchanged, regardless of variation of reaction conditions, i.e. [Al]/[V], ageing time, and reaction temperature, indicating the high stability of stereospecificity of the active sites.

The effect of preparation conditions on the catalyst Nd(P-507)(3)/H2O/Al(i-Bu)(3) for the polymerization of styrene

The catalyst system neodymium phosphonate Nd(P-507)(3)/H2O/Al(i-Bu)(3) for the polymerization of styrene was examined. Effects of the addition order of the catalyst components, catalyst aging time and aging temperature on the catalyst activity and the polymer characteristics were investigated. The catalyst activity for isospecific polymerization of styrene increases with aging time and reaches the maximum with a catalyst aged for 45 min at 70 degrees C. The aging time that the catalyst needs to reach the highest activity for isospecific polymerization decreases with increasing aging temperature. The preformed catalyst and the in situ catalyst were compared with respect to the kinetic behavior of the styrene polymerization and the polymer characteristics.

Pore-water chemistry at DSDP Leg 70 Holes

Geological and geophysical data collected during Deep Sea Drilling Project (DSDP) Leg 70 indicate that hydrothermal solutions are upwelling through the sediments of the mounds hydrothermal field (Sites 506, 507, and 509) and downwelling in the low heat-flow zone to the south (Site 508). Pore-water data are compatible with these conclusions. Pore waters at mounds sites are enriched in Ca and depleted in Mg relative to both seawater and Site 508 pore waters. These anomalies are believed to reflect prior reaction of the interstitial waters with basement rocks. The mounds solutions are also enriched in iron, which is probably hydrothermal and en route to forming nontronite. Concentrations of Si and NH3 in mounds pore water increase upcore as a result of the addition of dissolving biogenic debris to ascending hydrothermal solutions. Some low heat-flow pore-water samples (Site 508) are enriched in Ca and depleted in Mg. These anomalies likely reflect the presence of pockets of hydrothermal solutions in areas otherwise dominated by downwelling bottom water.

(Table 7) Fe**3+/Fe**2+ ratios in selected nontronite samples at DSDP Leg 70 Holes

Since its discovery in 1974 (Klitgord and Mudie, 1974), the Galapagos mounds hydrothermal field has received much attention. Sediment samples were taken during Leg 54 of the Deep Sea Drilling Project (DSDP) and by other expeditions to the area (e.g., Corliss et al., 1978). While a hydrothermal origin for the mounds sediments has been generally accepted, several different theories of origin for the mounds themselves have been proposed (e.g., Corliss et al., 1978; Natland et al., 1979; Williams et al., 1979). One of the aims of DSDP Leg 70 was to return to the mounds field and, using the new hydraulic piston cor er described elsewhere in this volume, to obtain more complete recovery of mounds sediments than had previously been possible. It was our hope that this would help in our understanding of the nature and origin of these deposits. In this chapter, we describe the results of chemical analysis of over 250 sediment samples taken during the course of Leg 70.