Fast mobility support in low-power wireless networks: smart-HOP over RPL/6LoWPAN

With the emergence of low-power wireless hardware new ways of communication were needed. In order to standardize the communication between these low powered devices the Internet Engineering Task Force (IETF) released the 6LoWPAN stand- ard that acts as an additional layer for making the IPv6 link layer suitable for the lower-power and lossy networks. In the same way, IPv6 Routing Protocol for Low- Power and Lossy Networks (RPL) has been proposed by the IETF Routing Over Low power and Lossy networks (ROLL) Working Group as a standard routing protocol for IPv6 routing in low-power wireless sensor networks. The research performed in this thesis uses these technologies to implement a mobility process. Mobility management is a fundamental yet challenging area in low-power wireless networks. There are applications that require mobile nodes to exchange data with a xed infrastructure with quality-of-service guarantees. A prime example of these applications is the monitoring of patients in real-time. In these scenarios, broadcast- ing data to all access points (APs) within range may not be a valid option due to the energy consumption, data storage and complexity requirements. An alternative and e cient option is to allow mobile nodes to perform hand-o s. Hand-o mechanisms have been well studied in cellular and ad-hoc networks. However, low-power wireless networks pose a new set of challenges. On one hand, simpler radios and constrained resources ask for simpler hand-o schemes. On the other hand, the shorter coverage and higher variability of low-power links require a careful tuning of the hand-o parameters. In this work, we tackle the problem of integrating smart-HOP within a standard protocol, speci cally RPL. The simulation results in Cooja indicate that the pro- posed scheme minimizes the hand-o delay and the total network overhead. The standard RPL protocol is simply unable to provide a reliable mobility support sim- ilar to other COTS technologies. Instead, they support joining and leaving of nodes, with very low responsiveness in the existence of physical mobility.

Implementation and Evaluation of an Improved Header Compression for 6LoWPAN

Extending IPv6 to IEEE 802.15.4-based Low power Wireless Personal Area Networks requires efficient header compression mechanisms to adapt to their limited bandwidth, memory and energy constraints. This paper presents an experimental evaluation of an improved header compression scheme which provides better compression of IPv6 multicast addresses and UDP port numbers compared to existing mechanisms. This scheme outperforms the existing compression mechanism in terms of data throughput of the network and energy consumption of nodes. It enhances throughput by up to 8% and reduces transmission energy of nodes by about 5%.

Integration of wireless sensor networks to the internet of things using a 6LoWPAN Gateway

The Internet of Things is a new paradigm where smart embedded devices and systems are connected to the Internet. In this context, Wireless Sensor Networks (WSN) are becoming an important alternative for sensing and actuating critical applications like industrial automation, remote patient monitoring and domotics. The IEEE 802.15.4 protocol has been adopted as a standard for WSN and the 6LoWPAN protocol has been proposed to overcome the challenges of integrating WSN and Internet protocols. In this paper, the mechanisms of header compression and fragmentation of IPv6 datagrams proposed in the 6LoWPAN standard were evaluated through field experiments using a gateway prototype and IEEE 802.15.4 nodes.

BatNet: a 6LoWPAN-based sensors and actuators network

Improving energy efficiency in buildings is one of the goals of the Smart City initiatives and a challenge for the European Union. This paper presents a 6LoWPAN wireless transducer network (BatNet) as part of an open energy management system. This network has been designed to operate in buildings, to collect environmental information (temperature, humidity, illumination and presence) and electrical consumption in real time (voltage, current and power factor). The system has been implemented and tested in the Energy Efficiency Research Facility at CeDInt-UPM.

BatNet: red inalámbrica de sensores y actuadores basada en 6LoWPAN

El objetivo de las ciudades inteligentes consiste en mejorar la calidad de vida de sus ciudadanos mediante la integración de nuevos elementos arquitectónicos, innovaciones tecnológicas e infraestructuras de información y comunicación (TIC).

BatNet: an implementation of a 6LoWPAN sensor and actuator network

This demo presents BatNet, a 6LoWPAN Wireless Transducer Network, in a Home Automation context. Its suitability for such application is shown by means of several performance and usability tests.

A traffic differentiation add-on to the IEEE 802.15.4 protocol: implementation and experimental validation over a real-time operating system

The IEEE 802.15.4 is the most widespread used protocol for Wireless Sensor Networks (WSNs) and it is being used as a baseline for several higher layer protocols such as ZigBee, 6LoWPAN or WirelessHART. Its MAC (Medium Access Control) supports both contention-free (CFP, based on the reservation of guaranteed time-slots GTS) and contention based (CAP, ruled by CSMA/CA) access, when operating in beacon-enabled mode. Thus, it enables the differentiation between real-time and best-effort traffic. However, some WSN applications and higher layer protocols may strongly benefit from the possibility of supporting more traffic classes. This happens, for instance, for dense WSNs used in time-sensitive industrial applications. In this context, we propose to differentiate traffic classes within the CAP, enabling lower transmission delays and higher success probability to timecritical messages, such as for event detection, GTS reservation and network management. Building upon a previously proposed methodology (TRADIF), in this paper we outline its implementation and experimental validation over a real-time operating system. Importantly, TRADIF is fully backward compatible with the IEEE 802.15.4 standard, enabling to create different traffic classes just by tuning some MAC parameters.

Aplicação de Internet of Things em casas inteligentes: Serviços de Rede

O foco principal no estudo da Internet of Things tem sido a integração de dispositivos digitais com o mundo físico e vice-versa. Os dispositivos inteligentes têm vindo a ganhar uma forte presença na nossa vida diária e cada vez mais, tendem a integrar o sistema de uma casa, automatizando processos comuns como o controlo de temperatura ambiente ou mesmo a percentagem de luminosidade de uma divisão. A visão da IoT contempla um mundo interconectado, recolhendo informações de forma automática e possibilitando a comunicação entre dispositivos. Contudo, as tecnologias existentes para a criação de redes que albergam estes novos dispositivos carecem de padrões bem definidos, dificultando a interoperabilidade entre as diversas soluções existentes. Neste projeto são estudadas e aplicadas as tecnologias mais promissoras aplicáveis ao paradigma Internet of Things, com o objetivo de encontrar um conjunto de protocolos padrão para a implementação de sistemas de automação em casas inteligentes.1 Como objetivo final deste projeto, pretende-se criar uma rede de dispositivos com capacidades sensoriais que tenham a capacidade de comunicar com o mundo externo, permitindo o acesso à rede por qualquer tipo de utilizador. Com isso, espera-se caminhar para mais perto da padronização dos protocolos inerentes à IoT e habilitar interoperabilidade entre as mais diversas soluções. São apresentados e utilizados os protocolos que mais se adaptam ao tema escolhido, tentando simplificar a rede para que esta possa ser incluída em qualquer ambiente doméstico, recorrendo a hardware de custo reduzido. Os protocolos apresentados são o 6LoWPAN, utilizando o protocolo IEEE 802.15.4 como interface de rede juntamente com endereçamento IPv6. É também utilizado o protocolo CoAP na troca de mensagens entre os dispositivos.

mRPL: Boosting mobility in the Internet of Things

The 6loWPAN (the light version of IPv6) and RPL (routing protocol for low-power and lossy links) protocols have become de facto standards for the Internet of Things (IoT). In this paper, we show that the two native algorithms that handle changes in network topology – the Trickle and Neighbor Discovery algorithms – behave in a reactive fashion and thus are not prepared for the dynamics inherent to nodes mobility. Many emerging and upcoming IoT application scenarios are expected to impose real-time and reliable mobile data collection, which are not compatible with the long message latency, high packet loss and high overhead exhibited by the native RPL/6loWPAN protocols. To solve this problem, we integrate a proactive hand-off mechanism (dubbed smart-HOP) within RPL, which is very simple, effective and backward compatible with the standard protocol. We show that this add-on halves the packet loss and reduces the hand-off delay dramatically to one tenth of a second, upon nodes’ mobility, with a sub-percent overhead. The smart-HOP algorithm has been implemented and integrated in the Contiki 6LoWPAN/RPL stack (source-code available on-line mrpl: smart-hop within rpl, 2014) and validated through extensive simulation and experimentation.

Design of high fidelity building energy monitoring system

Building energy meter network, based on per-appliance monitoring system, willbe an important part of the Advanced Metering Infrastructure. Two key issues exist for designing such networks. One is the network structure to be used. The other is the implementation of the network structure on a large amount of small low power devices, and the maintenance of high quality communication when the devices have electric connection with high voltage AC line. The recent advancement of low-power wireless communication makes itself the right candidate for house and building energy network. Among all kinds of wireless solutions, the low speed but highly reliable 802.15.4 radio has been chosen in this design. While many network-layer solutions have been provided on top of 802.15.4, an IPv6 based method is used in this design. 6LOWPAN is the particular protocol which adapts IP on low power personal network radio. In order to extend the network into building area without, a specific network layer routing mechanism-RPL, is included in this design. The fundamental unit of the building energy monitoring system is a smart wall plug. It is consisted of an electricity energy meter, a RF communication module and a low power CPU. The real challenge for designing such a device is its network firmware. In this design, IPv6 is implemented through Contiki operation system. Customize hardware driver and meter application program have been developed on top of the Contiki OS. Some experiments have been done, in order to prove the network ability of this system.

Enterprise Integration of Smart Objects using Semantic Service Descriptions

Integrating physical objects (smart objects) and enterprise IT systems is still a labor intensive, mainly manual task done by domain experts. On one hand, enterprise IT backend systems are based on service oriented architectures (SOA) and driven by business rule engines or business process execution engines. Smart objects on the other hand are often programmed at very low levels. In this paper we describe an approach that makes the integration of smart objects with such backends systems easier. We introduce semantic endpoint descriptions based on Linked USDL. Furthermore, we show how different communication patterns can be integrated into these endpoint descriptions. The strength of our endpoint descriptions is that they can be used to automatically create REST or SOAP endpoints for enterprise systems, even if which they are not able to talk to the smart objects directly. We evaluate our proposed solution with CoAP, UDP and 6LoWPAN, as we anticipate the industry converge towards these standards. Nonetheless, our approach also allows easy integration with backend systems, even if no standardized protocol is used.

Open multi-technology building energy management system

Energy Efficiency is one of the goals of the Smart Building initiatives. This paper presents an Open Energy Management System which consists of an ontology-based multi-technology platform and a wireless transducer network using 6LoWPAN communication technology. The system allows the integration of several building automation protocols and eases the development of different kind of services to make use of them. The system has been implemented and tested in the Energy Efficiency Research Facility at CeDInt-UPM.

Simulador WKM para gestión de conocimiento en una WSN

La gestión del conocimiento (KM) se basa en la captación, filtración, procesamiento y análisis de unos datos en bruto que con dicho refinamiento podrán llegar a convertirse en conocimiento o Sabiduría. Estas prácticas tendrán lugar en este PFC en una WSN (Wireless Sensor Network) compuesta de unos sofisticados dispositivos comúnmente conocidos como “motas” y cuya principal característica son sus bajas capacidades en cuanto a memoria, batería o autonomía. Ha sido objetivo primordial de este Proyecto de fin de Carrera aunar una WSN con la Gestión del Conocimiento así como demostrar que es posible llevar a cabo grandes procesamientos de información, con tan bajas capacidades, si se distribuyen correctamente los procesos. En primera instancia, se introducen conceptos básicos acerca de las WSN (Wireless Sensor Networks) así como de los elementos principales en dichas redes. Tras conocer el modelo de arquitectura de comunicaciones se procede a presentar la Gestión del Conocimiento de forma teórica y a continuación la interpretación que se ha hecho a partir de diversas referencias bibliográficas para llevar a cabo la implementación del proyecto. El siguiente paso es describir punto por punto todos los componentes del Simulador; librerías, funcionamiento y demás cuestiones sobre configuración y puesta a punto. Como escenario de aplicación se plantea una red de sensores inalámbricos básica cuya topología y ubicación es completamente configurable. Se lleva a cabo una configuración a nivel de red basada en el protocolo 6LowPAN pero con posibilidad de simplificarlo. Los datos se procesan de acuerdo a un modelo piramidal de Gestión de Conocimiento adaptable a las necesidades del usuario. Mediante la utilización de las diversas opciones que proporciona la interfaz gráfica implementada y los documentos de resultados que se van generando, se puede llevar a cabo un detallado estudio posterior de la simulación y comprobar si se cumplen las expectativas planteadas. Knowledge management (KM) is based on the collection, filtering, processing and analysis of some raw data which such refinement it can be turned into knowledge or wisdom. These practices will take place in a WSN (Wireless Sensor Network) consists of sophisticated devices commonly known as "dots" and whose main characteristics are its low capacity for memory, battery or autonomy. A primary objective of this Project will be to join a WSN with Knowledge Management and show that it is possible make largo information processing, with such low capacity if the processes are properly distributed. First, we introduce basic concepts about the WSN (Wireless Sensor Networks) and major elements of these networks. After meeting the communications architecture model, we proceed to show the Knowledge Management theory and then the interpretation of several bibliographic references to carry out the project implementation. The next step is discovering point by point all over the Simulator components; libraries, operation and the rest of points about configuration and tuning. As application scenario we propose a basic wireless sensor network whose topology and location is completely customizable. It will perform a network level configuration based in W6LowPAN Protocol. Data is processed according to a pyramidal pattern Knowledge Management adaptable to the user´s needs. The hardware elements will suffer more or less energy dependence depending on their role and activity in the network. Through the various options that provide the graphical interface has been implemented and results documents that are generated, can be carried out after a detailed study of the simulation and verify compliance with the expectations raised.

Esineiden internetin verkkostandardit älykodissa

Tutkielman tavoitteena on esitellä esineiden internetin kokonaisuutta ja tutkia siellä käytettäviä langattomia verkkostandardeja sekä niiden käyttöä älykodissa. Esineiden internetin soveltamisalueet jakautuvat älykodin, teollisuuden ja yhteiskunnan osa-alueisiin. Näistä älykotia käsitellään tutkielmassa tarkemmin. Työssä selvitetään, mitkä ovat esineiden internetin yleisimmät langattomat verkkostandardit ja niiden ominaisuudet. Lisäksi selvitetään, mistä osista älykoti koostuu, mitkä ovat soveltamisalueet ja miten älykoti toimii. Vertailukohteina käytetään kahden suuren elektroniikkavalmistajan, Samsungin ja LG:n, älykotiratkaisuja. Tutkielmassa esitellään esineiden internetin määritelmä, sen historiaa ja käyttökohteita, jotta saadaan yleiskuva esineiden internetin kokonaisuudesta. Tämän jälkeen syvennytään langattomiin verkkostandardeihin, jotka ovat keskeisesti käytössä esineiden internetissä. Kyseiset verkkostandardit ovat Bluetooth, Bluetooth Low Energy, NFC, Wi-Fi, Zigbee ja 6LoWPAN. Lopuksi käsitellään älykotia ja sen ominaisuuksia. Samalla tutkitaan Samsungin ja LG:n älykotilaitteita ja pohditaan niiden toimivuutta. Lisäksi pohditaan verkkostandardien käyttöä älykodeissa sekä esineiden internetin ja älylaitteiden vaikutuksia ihmisiin. Lopputuloksena todetaan, että Wi-Fi, Bluetooth ja Zigbee ovat yleisimmät älykodin verkkostandardit ja että ainoastaan yksi verkkostandardi ei tällä hetkellä riitä monipuolisen älykodin kaikkia toimintoja varten. Vertailussa huomataan Samsungin älykotiratkaisun olevan kehityksessä LG:tä edellä.

Street lighting mesh network protocol

The digital revolution of the 21st century contributed to stem the Internet of Things (IoT). Trillions of embedded devices using the Internet Protocol (IP), also called smart objects, will be an integral part of the Internet. In order to support such an extremely large address space, a new Internet Protocol, called Internet Protocol Version 6 (IPv6) is being adopted. The IPv6 over Low Power Wireless Personal Area Networks (6LoWPAN) has accelerated the integration of WSNs into the Internet. At the same time, the Constrained Application Protocol (CoAP) has made it possible to provide resource constrained devices with RESTful Web services functionalities. This work builds upon previous experience in street lighting networks, for which a proprietary protocol, devised by the Lighting Living Lab, was implemented and used for several years. The proprietary protocol runs on a broad range of lighting control boards. In order to support heterogeneous applications with more demanding communication requirements and to improve the application development process, it was decided to port the Contiki OS to the four channel LED driver (4LD) board from Globaltronic. This thesis describes the work done to adapt the Contiki OS to support the Microchip TM PIC24FJ128GA308 microprocessor and presents an IP based solution to integrate sensors and actuators in smart lighting applications. Besides detailing the system’s architecture and implementation, this thesis presents multiple results showing that the performance of CoAP based resource retrievals in constrained nodes is adequate for supporting networking services in street lighting networks.