Implementering av felpredikteringoch frekvenshopp i ett 2,4 GHzradiosystem

Maxicap AB är ett företag som utvecklar och tillverkar elektronisk utrustning för bland annat olika mätuppgifter. Målet med detta examensjobb var att undersöka och implementera en stabil trådlös dataöverföringsmetod med den utrustning som Maxicap ville använda. Detta skulle åstadkommas/testas genom att sända temperatursensorvärden trådlöst med Nordic Semiconductor’ssändtagare (eng. transceiver) styrda av Atmel’s mikrokontrollers. Arbetet fokuserade på att få till denna stabila trådlösa överföring genom att implementera frekvenshoppning och datapaketskontroll på datatrafiken inom det fria 2,4 GHz ISM-bandet. All den C-kod som utvecklades i detta arbete är skriven för att vara lättanpassad till flera olika modeller av mikrokontrollers inom Atmel’s produktserie samt att kunna användas till andra liknande projekt. Koden är väldokumenterad med kommentarer vid varje funktionsblock som beskriver vad funktionerna gör och hur de skall användas. Arbetet resulterade i två fungerande prototyper. En enhet känner av temperaturen i luften och skickar sedan detta temperaturvärde trådlöst till enhet nummer två. Detta värde samt några inställningsvärden för mottagaren visas sedan på den enhetens display.

Frequency diversity measurements at 2.4 GHz for wireless sensor networks deployed in tunnels

Wireless Sensor Networks (WSNs) which utilise IEEE 802.15.4 technology operate primarily in the 2.4 GHz globally compatible ISM band. However, the wireless propagation channel in this crowded band is notoriously variable and unpredictable, and it has a significant impact on the coverage range and quality of the radio links between the wireless nodes. Therefore, the use of Frequency Diversity (FD) has potential to ameliorate this situation. In this paper, the possible benefits of using FD in a tunnel environment have been quantified by performing accurate propagation measurements using modified and calibrated off-the-shelf 802.15.4 based sensor motes in the disused Aldwych underground railway tunnel. The objective of this investigation is to characterise the performance of FD in this confined environment. Cross correlation coefficients are calculated from samples of the received power on a number of frequency channels gathered during the field measurements. The low measured values of the cross correlation coefficients indicate that applying FD at 2.4 GHz will improve link performance in a WSN deployed in a tunnel. This finding closely matches results obtained by running a computational simulation of the tunnel radio propagation using a 2D Finite-Difference Time-Domain (FDTD) method. ©2009 IEEE.

A power scalable receiver front-end at 2.4 GHz

We propose a Low Noise Amplifier (LNA) architecture for power scalable receiver front end (FE) for Zigbee. The motivation for power scalable receiver is to enable minimum power operation while meeting the run-time performance needed. We use simple models to find empirical relations between the available signal and interference levels to come up with required Noise Figure (NF) and 3rd order Intermodulation Product (IIP3) numbers. The architecture has two independent digital knobs to control the NF and IIP3. Acceptable input match while using adaptation has been achieved by using an Active Inductor configuration for the source degeneration inductor of the LNA. The low IF receiver front end (LNA with I and Q mixers) was fabricated in 130nm RFCMOS process and tested.

A power-scalable RF CMOS receiver for 2.4 GHz Wireless Sensor Network applications

A power scalable receiver architecture is presented for low data rate Wireless Sensor Network (WSN) applications in 130nm RF-CMOS technology. Power scalable receiver is motivated by the ability to leverage lower run-time performance requirement to save power. The proposed receiver is able to switch power settings based on available signal and interference levels while maintaining requisite BER. The Low-IF receiver consists of Variable Noise and Linearity LNA, IQ Mixers, VGA, Variable Order Complex Bandpass Filter and Variable Gain and Bandwidth Amplifier (VGBWA) capable of driving variable sampling rate ADC. Various blocks have independent power scaling controls depending on their noise, gain and interference rejection (IR) requirements. The receiver is designed for constant envelope QPSK-type modulation with 2.4GHz RF input, 3MHz IF and 2MHz bandwidth. The chip operates at 1V Vdd with current scalable from 4.5mA to 1.3mA and chip area of 0.65mm2.

A 4 GHz non-resonant clock driver with inductor-assisted energy return to power grid

Power consumption of a multi-GHz local clock driver is reduced by returning energy stored in the clock-tree load capacitance back to the on-chip power-distribution grid. We call this type of return energy recycling. To achieve a nearly square clock waveform, the energy is transferred in a non-resonant way using an on-chip inductor in a configuration resembling a full-bridge DC-DC converter. A zero-voltage switching technique is implemented in the clock driver to reduce dynamic power loss associated with the high switching frequencies. A prototype implemented in 90 nm CMOS shows a power savings of 35% at 4 GHz. The area needed for the inductor in this new clock driver is about 6% of a local clock region. © 2006 IEEE.

2.4 GHz Class-E power amplifier with transmissionline harmonic terminations

The design procedure, fabrication and measurement of a Class-E power amplifier with excellent second- and third-harmonic suppression levels are presented. A simplified design technique offering compact physical layout is proposed. With a 1.2 mm gate-width GaAs MESFET as a switching device, the amplifier is capable of delivering 19.2 dBm output power at 2.41 GHz, achieves peak PAE of 60% and drain efficiency of 69%, and exhibits 9 dB power gain when operated from a 3 V DC supply voltage. When compared to the classical Class-E two-harmonic termination amplifier, the Class-E amplifier employing three-harmonic terminations has more than 10% higher drain efficiency and 23 dB better third-harmonic suppression level. Experimental results are presented and good agreement with simulation is obtained. Further, to verify the practical implementation in communication systems, the Bluetooth-standard GFSK modulated signal is applied to both two- and three-harmonic amplifiers. The measured RMS FSK deviation error and RMS magnitude error were, for the three-harmonic case, 1.01 kHz and 0.122%, respectively, and, for the two-harmonic case, 1.09 kHz and 0.133%. © 2007 The Institution of Engineering and Technology.

2.4 GHz high-efficiency power-combining Class-E amplifier with transmission-line harmonic traps

Experimental assessments of the modified power-combining Class-E amplifier are described. The technique used to combine the output of individual power amplifiers (PAs) into an unbalanced load without the need for bulky transformers permits the use of small RF chokes useful for the deployment in the EER transmitter. The modified output load network of the PA results in excellent 50 dBc and 46 dBc second and third-harmonic suppressions, dispensing the need for additional lossy filtering block. Operating from a 3.2 V dc supply voltage, the PA exhibits 64% drain efficiency at 24 dBm output power. Over a wide bandwidth of 350 MHz, drain efficiency of better than 60% at output power higher than 22 dBm were achieved. © 2010 IEICE Institute of Electronics Informati.

Compact Wideband Antenna for 2.4 GHz WLAN Applications

A novel compact wideband antenna for wireless local area network (WLAN) applications in the 2.4 GHz band are presented. The proposed low profile antenna of dimensions 15 x 14.5 x 1.6 mm offers 18.6% bandwidth and an average gain of~5 dBi. The antenna can be excited directly using a 50 coaxial probe

Compact Wideband Antenna for 2.4 GHz WLAN Applications

A novel compact wideband antenna for wireless local area network (WLAN) applications in the 2.4 GHz band is presented. The proposed low profile antenna of dimensions 15 x 14.5 x 1.6 mm offers 18.6% bandwidth and an average gain of -5 dBi. The antenna can be excited directly using a 50 coaxial probe

A wideband printed monopole antenna for 2.4-GHz WLAN applications

A planar monopole antenna suitable for broadband wireless communication is designed and developed. With the use of a truncated ground plane, the proposed printed monopole antenna offers nearly 60% 2:1 VSWR bandwidth and good radiation characteristics for the frequencies across the operating band. A parametric study of the antenna is performed based on the optimized design, and a prototype of the antenna suitable for 2.4-GHz WLAN application is presented. The antenna can be easily integrated into wireless circuitry and is convenient for application in laptop computers.

Modelo de propagação indoor multi-andar em 2.4 GHz com estimativa de parâmetros de QoS em chamadas VoIP

O advento de novas formas multimídia tem atraído uma clientela exigente, onde preocupação não é somente com o serviço, mas também, com a qualidade que esse serviço pode ser oferecido. As WLAN (Wireless Local Area Networks) tornaram-se a forma mais comum de roteamento de Internet, devido ao seu baixo custo e facilidade de implementação. Para realizar um bom roteamento é necessário um planejamento, utilizando-se modelos. Os modelos de propagação existentes na literatura fazem a predição da intensidade do sinal, mas algumas vezes não contemplam a previsão de um bom serviço. Nesse sentido a presente dissertação propõe-se a elaborar um modelo de propagação empírico indoor multi-andar que não só prediz a potência recebida, mas também faz uma previsão para algumas métricas de QoS (Quality of Service) de chamadas VoIP (Voice over Internet Protocol). Para a elaboração do modelo proposto foram feitas campanhas de medição, em um prédio de dois andares, em pisos distintos mantendo-se a posição do ponto de acesso (PA) fixa. Estudos de geometria analítica para a contagem e agregação de perdas em pisos e paredes. Os resultados do modelo proposto foram comparados com um modelo da literatura que tem um comportamento similar, onde é possível verificar o melhor desempenho do modelo proposto, e para efeito de estudo um andar completamente simulado foi introduzido para avaliação.

Measurement of Distributed Antenna Systems at 2.4 GHz in a Realistic Subway Tunnel Environment.

Accurate characterization of the radio channel in tunnels is of great importance for new signaling and train control communications systems. To model this environment, measurements have been taken at 2.4 GHz in a real environment in Madrid subway. The measurements were carried out with four base station transmitters installed in a 2-km tunnel and using a mobile receiver installed on a standard train. First, with an optimum antenna configuration, all the propagation characteristics of a complex subway environment, including near shadowing, path loss,shadow fading, fast fading, level crossing rate (LCR), and average fade duration (AFD), have been measured and computed. Thereafter, comparisons of propagation characteristics in a double-track tunnel (9.8-m width) and a single-track tunnel (4.8-m width) have been made. Finally, all the measurement results have been shown in a complete table for accurate statistical modeling.

A modified dual-band microstrip monopole antenna

A modified microstrip-fed planar monopole antenna with open circuited coupled line is presented in this paper. The operational bandwidth of the proposed antenna covers the 2.4 GHz ISM band (2.42-2.48 GHz) and the 5 GHz WLAN band (5 GHz to 6 GHz). The radiating elements occupy a small area of 23×8 mm2. The Finite Difference Time Domain method is used to predict the input impedance of the antenna. The calculated return loss shows very good agreement with measured data. Reasonable antenna gain is observed across the operating band. The measured radiation patterns are similar to those of a simple monopole antenna.