Nicklinson v Ministry of Justice [2012] 304 (QB) : further UK developments regarding a person's right to choose when and how to die : assisted termination of life

UK High Court decision - application for declarations legitimising third party assistance in voluntary termination of life - facts - moral, social and ethical issues - analysis.

A Curious Harpour in Helle : An Edition of the Commentary on the Orpheus Metre of De consolatione philosophiae in MS Thott 304,2

Tutkielmani on tekstieditio keskiaikaisesta kommentaarista, joka löytyy Kööpenhaminan Kuninkaallisen kirjaston käsikirjoituksesta Thott 304,2. Käsikirjoitus voidaan ajoittaa 1400-luvun ensimmäiselle neljännekselle ja se on kirjoitettu keskienglanniksi. Se sisältää John Waltonin runomuotoisen käännöksen Boethiuksen 500-luvun alussa latinaksi kirjoittamasta teoksesta De consolatione philosophiae (Filosofian lohdutus) sekä teosta kommentoivan proosamuotoisen kommentaarin. Käsikirjoitus on vaillinainen, mutta sen säilyneet foliot ovat enimmäkseen erittäin hyväkuntoisia. Itse käsikirjoitusta on tutkittu vain muutamissa artikkeleissa ja yhdessä tutkielmassa; kommentaarista ei ole toistaiseksi tehty kattavaa tutkimusta. Tavoitteeni onkin tuoda kommentaari keskiaikaisen filosofian, keskienglannin ja käsikirjoitusten tutkijoiden käytettäviin. Käsikirjoitus Thott 304,2 on esimerkki epätyypillisestä myöhäiskeskiaikaisesta maallikkomesenaattiudesta Englannissa. Tavanmukaisesti maallikkomesenaatit tukivat uskonnollisten tekstien tuottamista ja kääntämistä, kun taas Thott 304,2 sisältää käännöksen filosofisesta tekstistä. Sen lisäksi mesenaatti oli nainen, aatelistoon kuuluva Elizabeth Berkeley. Varsin harvinaiseksi käsikirjoituksen tekee sen painaminen kirjaksi 1500-luvun alussa. Kirjanpainajan käsikirjoituksen sivuille tekemistä merkinnöistä saadaan korvaamatonta tietoa varhaisesta painotekniikasta, sillä kirjanpainajien käyttämiä käsikirjoituskopioita ei ole säilynyt kovin runsaasti. Waltonin käännös on säilynyt yli kahdessakymmenessä käsikirjoituskopiossa, joista vain Thott 304,2 sisältää laajan kommentaarin. 1500-luvun painoksesta on jäljellä kolme kopiota, ja ne sisältävät saman kommentaarin kuin Thott 304,2. Valitsin editoitavaksi niin kutsuttua Orfeus-runoa kommentoivan osan kommentaarista, sillä se muodostaa ehjän kokonaisuuden ja sopii pituutensa puolesta Pro gradu -tutkielmaan. Orfeus-runo on myös yksi käsikirjoituksen kattavimmin kommentoiduista runoista. Editio on niin sanottu diplomaattinen transkriptio, jossa käsikirjoituksen piirteet on pyritty säilyttämään mahdollisimman tarkasti edition luettavuuden siitä kuitenkaan kärsimättä. Perinteisistä editioista poiketen tutkielmani sisältää myös kommentaarin ja Orfeus-runon transkriptiot, joissa rivijako, lyhenteet ja erikoismerkit on säilytetty. Näiden transkriptioiden toivon auttavan erityisesti käsikirjoituksessa esiintyvien lyhenteiden, erikoismerkkien ja kirjanpainajan merkintöjen tulkinnassa ja tutkimisessa. Editiota ja transkriptioita täydentävät nykyenglanniksi kirjoitettu lyhennelmä kommentaarista ja kuvat käsikirjoituksen sivuista, joilla editoimani kommentaari on. Tutkielmaan sisältyy alkuperäisen tekstin, käännöksen, kommentaarin ja käsikirjoituksen taustaa valottava osuus. Esittelen myös kaikki löytämäni lähteet, joissa käsikirjoitus on mainittu tai joissa sitä on tutkittu. Liitteeksi olen laatinut sanaston helpottamaan kommentaarin tulkitsemista.

Influence of cast versus wrought microstructure on the processing map for hot working of stainless steel type AISI 304

Processing maps for hot working of as-cast and wrought stainless steels of type AISI 304 have been developed in the temperature range 600 to 1250°C and strain rate range 0.001 to 100 s−1. The domain of dynamic recrystallization (DRX) in as-cast material occurs at higher temperatures (1250°C) and lower strain rates (0.001 s−1) than in the wrought steel (1100°C and 0.01 s−1). The effect is explained in terms of enhanced nucleation rate of DRX due to the carbide, ferrite particles, stable oxides/nitrides and second-phase intermetallics in the as-cast microstructure. The DRX domain is wider in the wrought material although the peak efficiency is less (32%) than in the as-cast case (40%). The flow instability regime is not significantly affected by the initial microstructure

Influence of strain rate and state-of-stress on the formation of ferrite in stainless steel type AISI 304 during hot working

The influence of strain rate and state-of-stress on the formation of ferrite in stainless steel type AISI 304L, 304 and 304 as-cast, during hot working has been studied. Compression and torsion tests were conducted in the temperature range 1100 to 1250 degrees C and strain rate range 0.001 to 100 s(-1) on these materials, Ferrite formation occurs during deformation at temperatures above 1150 degrees C and strain rates above 10 s(-1), in stainless steel type AISI 304L and 304. The tendency for the formation of ferrite is more in as-cast 304 than in wrought 304, In as-cast 304 the ferrite forms at lower temperatures and strain rates, The tendency for the ferrite formation is more in torsion than in compression.

Optimization of cold and warm workability in 304 stainless steel using instability maps

The deformation characteristics of stainless steel type AISI 3O4 under compression in the temperature range 20 degrees C to 600 degrees C and strain-rate range 0.001 to 100 s(-1) have been studied with a view to characterizing the flow instabilities occurring in the microstructure. At strain rates less than 5 s(-1), 304 stainless steel exhibits flow localization, whereas dynamic strain aging occurs at intermediate temperatures and below 0.5 s(-1). At room temperatures and strain rates less than 10 s(-1), martensite formation is observed. To avoid the preceding microstructural instabilities, cold and warm working should be carried out at strain rates greater than 5 s(-1). The continuum criterion, developed on the basis of the principles of maximum rate of entropy production and separability of the dissipation function, predicts accurately all the preceding instability features.

Influence of carbide particles on the dynamic recrystallization of as-cast 304 stainless steel: a study using secondary ion mass spectrometric (SIMS) analysis

The domain of dynamic recrystallization (DRX) in as-cast 304 stainless steel material occurs at higher temperatures (1250 degrees C) and lower strain rates (0.001 s(-1)) than in wrought 304 stainless steel (1100 degrees C and 0.01 s(-1)). The above result has been explained earlier on the basis of a simple theoretical DRX model involving the rate of nucleation versus rate of grain boundary migration. The present investigation is aimed at examining experimentally the influence of carbide particles on the DRX of ascast 304 using secondary ion mass spectrometric (SIMS) analysis. Isothermal compression tests at a constant true strain rate have been performed on wrought 304 and as-cast 304 materials in the temperature and strain rate ranges of 1000 to 1250 degrees C and 0.001 to 1 s(-1) respectively. The SIMS analysis carried out on the deformed samples revealed that the large carbides present in the as-cast 304 material strongly influence the DRX process. In as-cast 304 material, the presence of large carbide particles in the microstructure shifts the DRX domain to higher temperature and lower strain rate in comparison with wrought 304 material.

Instability map for cold and warm working of as-cast 304 stainless steel

The deformation characteristics of as-cast 304 stainless steel under compression in the temperature range 20-600 degrees C and strain rate range 0.001-100 s(-1) have been studied with a view to characterizing the flow instabilities occurring in the microstructure. Ar strain rates of less than 0.05 s(-1), as-cast 304 stainless steel exhibits flow localization in the temperature range 20-600 degrees C, whereas dynamic strain ageing occurs at intermediate temperatures and below 5 s(-1). At room temperatures and strain rates of less than 0.05 s(-1), martensite formation is observed. To avoid the above microstructural instabilities warm working should be carried out at strain rates greater than 10 s(-1) in the temperature range 400-600 degrees C and cold working could be done in the range of about 0.05-0.8 s(-1). The continuum criterion developed on the basis of the principles of maximum rate of entropy production and separability of the dissipation function, predicts accurately all of the above instability features. (C) 1997 Elsevier Science S.A.

Photodissociation dynamics of CH2ICl at 222, 236, 266, 280, and-304 nm

Dynamics of I*(P-2(1/2)) formation from CH2ICl dissociation has-been investigated at five different ultraviolet excitation wavelengths, e.g., 222, 236, 266, 280, and similar to304 nm. The quantum yield of I*((2)p(1/2)) production, phi*, has been measured by monitoring nascent I(P-2(3/2)) and I* concentrations using a resonance enhanced multiphoton ionization detection scheme. The measured quantum yield as a function of excitation energy follows the same trend as that of methyl iodide except at 236 run. The photodissociation dynamics of CH2ICl also involves three upper states similar to methyl iodide, and a qualitative correlation diagram has been constructed to account for the observed quantum yield. From the difference in behavior at 236 nm, it appears that the crossing region between the two excited states ((3)Q(0) and (1)Q(1)) is located near the exit valley away from the Franck Condon excitation region. The B- and C-band transitions do not participate in the dynamics, and the perturbation of the methyl iodide states due to Cl-I interaction is relatively weak at the photolysis wavelengths employed in this investigation.

Grain-Size Effects on the High-Temperature Oxidation of Modified 304 Austenitic Stainless Steel

The high-temperature oxidation behavior of modified 304 austenitic stainless steels in a water vapor atmosphere was investigated. Samples were prepared by various thermo mechanical treatments to result in different grain sizes in the range 8-30 mu m. Similar I 3 pound grain boundary fraction was achieved to eliminate any grain-boundary characteristics effect. Samples were oxidized in an air furnace at 700 A degrees C with 20 % water vapor atmosphere. On the fine-grained sample, a uniform Cr2O3 layer was formed, which increased the overall oxidation resistance. Whereas on the coarse-grained sample, an additional Fe2O3 layer formed on the Cr-rich oxide layer, which resulted in a relatively high oxidation rate. In the fine-grained sample, grain boundaries act as rapid diffusion paths for Cr and provided enough Cr to form Cr2O3 oxide on the entire sample surface.

Estudo comparativo da citotoxicidade de cimentos obturadores sobre culturas de células endoteliais da linhagem ECV 304

Este estudo teve como objetivo avaliar, in vitro, a citotoxicidade dos cimentos endodônticos Densell Endo, Pulp-Fill, Endofill, Sealer 26, Pulp Canal Sealer e GuttaFlow após 12, 24 e 72 horas de tempo de contato, utilizando-se uma linhagem de células endoteliais ECV-304. Para a avaliação da viabilidade celular, utilizou-se o teste de citotoxicidade MTT. Para cada cimento foram preparados 12 corpos de prova que foram distribuídos em seis grupos experimentais de acordo com as marcas comerciais, sendo quatro para cada tempo. Foi criado um grupo controle que não foi submetido à ação de cimento. Para avaliação do efeito dos cimentos sobre as células endoteliais, os corpos de prova foram inseridos nos poços da placa cultura, incubados a 37C em presença de 5% de CO2 e 100% de umidade. Os testes MTT foram realizados, em quadruplicata, após 12, 24 e 72 horas de contato das amostras com o tapete celular. Foi utilizada a prova Two-Way Anova com o teste Post Hoc de Bonferroni com nível de significância de 5%. Na análise de 12 horas, foi possível observar que o cimento GuttaFlow apresentou média de absorbância de 0,055, seguido do Sealer 26 (média = 0,038). Os cimentos Pulp Canal Sealer e Densell Endo apresentaram a mesma média de absorbância (0,031). O Pulp Fill e o Endofill foram os cimentos que apresentaram maior citotoxicidade (média de absorbância = 0,024 e 0,021, respectivamente). O grupo controle apresentou média de absorbância de 0,158. Em 24 horas observou-se que os cimentos GuttaFlow e Sealer 26 apresentaram as maiores médias de absorbância (0,041 e 0,037, respectivamente), seguidos pelo cimento Pulp Canal Sealer que apresentou média de absorbância de 0,035. Já os cimentos Densell Endo e Pulp Fill apresentaram médias de absorbância de 0,033 e 0,032, respectivamente. O cimento Endofill apresentou uma média de 0,026 e o grupo controle de 0,086. Quando analisados em 72 horas, o cimento Pulp Canal Sealer obteve média de absorbância de 0,049, seguido dos cimentos GuttaFlow e Pulp Fill, ambos com 0,048. Os cimentos Densell Endo, Sealer 26 e Endofill apresentaram respectivamente, médias de 0,044, 0,040 e 0,036. O grupo controle diferenciou-se significativamente de todos os grupos em todos os tempos. Quando analisadas as médias gerais de absorbância dos grupos analisados observou-se que o cimento GuttaFlow se apresentou como o cimento com menor índice de citotoxicidade, apresentando média de absorbência de 0,048. Logo após, apresentando médias de absorbância iguais (0,038) encontraram-se os cimentos Pulp Canal Sealer e Sealer 26; seguidos do Densell Endo e do Pulp Fill, com 0,036 e 0,035, respectivamente. O grupo controle apresentou média de absorbância de 0,098. Portanto, tendo como base os resultados obtidos, pôde-se concluir que o cimento Endofill foi o que apresentou maior citotoxicidade e o cimento GuttaFlow, o menos citotóxico.

Multi-hit ballistic damage characterisation of 304 stainless steel plates with finite elements

Multi-impact of projectiles on thin 304 stainless steel plates is investigated to assess the degradation of ballistic performance, and to characterise the inherent mechanisms. Assessment of ballistic degradation is by means of a double-impact of rigid spheres at the same site on a circular clamped plate. The limiting velocity of the second impact, will be altered by the velocity of the antecedent impact. Finite element analyses were used to elucidate experimental results and understand the underlying mechanisms that give rise to the performance degradation. The effect of strength and ductility on the single and multi-impact performance was also considered. The model captured the experimental results with excellent agreement. Moreover, the material parameters used within the model were exclusively obtained from published works with no fitting or calibration required. An attempt is made to quantify the elevation of the ballistic limit of thin plates by the dynamic mechanism of travelling hinges. Key conclusions: The multi-hit performance scales linearly with the single-hit performance; and strength is a significantly greater effector of increased ballistic limit than ductility, even at the expense of toughness. © 2014 Elsevier Ltd.