(Table 1) Summary of basalt unit thickness, vesicularity, number of flow units, and average porosity at ODP Site 135-839

An inflatable drill-string packer was used at Site 839 to measure the bulk in-situ permeability within basalts cored in Hole 839B. The packer was inflated at two depths, 398.2 and 326.9 mbsf; all on-board information indicated that the packer mechanically closed off the borehole, although apparently the packer hydraulically sealed the borehole only at 398.2 mbsf. Two pulse tests were run at each depth, two constant-rate injection tests were run at the first set, and four were run at the second. Of these, only the constant-rate injection tests at the first set yielded a permeability, calculated as ranging from 1 to 5 * 10**-12 m**2. Pulse tests and constant-rate injection tests for the second set did not yield valid data. The measured permeability is an upper limit; if the packer leaked during the experiments, the basalt would be less permeable. In comparison, permeabilities measured at other Deep Sea Drilling Project and Ocean Drilling Program sites in pillow basalts and flows similar to those measured in Hole 839B are mainly about 10**-13 to 10**-14 m**2. Thus, if our results are valid, the basalts at Site 839 are more permeable than ocean-floor basalts investigated elsewhere. Based on other supporting evidence, we consider these results to be a valid measure of the permeability of the basalts. Temperature data and the geochemical and geotechnical properties of the drilled sediments all indicate that the site is strongly affected by fluid flow. The heat flow is very much less than expected in young oceanic basalts, probably a result of rapid fluid circulation through the crust. The geochemistry of pore fluids is similar to that of seawater, indicating seawater flow through the sediments, and sediments are uniformly underconsolidated for their burial depth, again indicating probable fluid flow. The basalts are highly vesicular. However, the vesicularity can only account for part of the average porosity measured on the neutron porosity well log; the remainder of the measured porosity is likely present as voids and fractures within and between thin-bedded basalts. Core samples, together with porosity, density, and resistivity well-log data show locations where the basalt section is thin bedded and probably has from 15% to 35% void and fracture porosity. Thus, the measured permeability seems reasonable with respect to the high measured porosity. Much of the fluid flow at Site 839 could be directed through highly porous and permeable zones within and between the basalt flows and in the sediment layer just above the basalt. Thus, the permeability measurements give an indication of where and how fluid flow may occur within the oceanic crust of the Lau Basin.

Chemical and boron isotopic compositions of volcanics from ODP Sites 135-834 to 135-840

The influence of fluid flux on petrogenesis in the Tonga-Kermadec Arc was investigated using ion microprobe measurements of B/Be and boron isotope ratios (11B/10B) to document the source and relative volumes of the fluids released from the subducting oceanic plate. We analyzed young lavas from eight different islands along the Tonga-Kermadec Arc, as well as glass shards in volcanic sediments from Ocean Drilling Program (ODP) Site 840, which record the variations in the chemistry of Tonga magmatism since 7 Ma. B/Be is variable (5.8-122), in young Tonga-Kermadec Arc lavas. In contrast, glass shards from around 3 to 4 Ma old volcanic sediments at Site 840 have the highest B/Be values yet reported for arc lavas (18-607). These values are too high to be related simply to a sediment influence on petrogenesis. Together with very high d11B values (-11.6 to +37.5) for the same shards and lavas these data indicate that most of the B is derived from fluid escaped from the subducting altered Pacific oceanic crust, rather than from sediment. High d11B values also reflect large degrees of isotopic fractionation in this cold fast subduction zone. Lower d11B values noted in the Kermadec Arc (17 to -4.4) are related to the influence of sediment eroded from New Zealand and slower convergence. High fluid flux (B/Be) is synchronous in Tonga and the Marianas at 3 to 4 Ma and may be related to acceleration of the Pacific Plate just prior to this time. The timing of maximum B/Be at 3 to 4 Ma correlates with maximum light rare earth (LREE) and high field strength element depletion. This suggests maximum degrees of partial melting at this time. Although thinning of the arc lithosphere during rifting to form the Lau Basin is expected to influence the arc geochemistry, variable aqueous fluid flux from the subducting plate alone appears capable of explaining boron and other trace element systematics in the Tonga-Kermadec Arc with no indication of slab melting.

Geochemistry of ODP Leg 135 vitrophyric rhyolite samples

In-situ proton-microprobe analyses are presented for glasses, plagioclases, pyroxenes, olivines, and spinels in eleven samples from Sites 834-836, 839, and 841 (vitrophyric rhyolite), plus a Tongan dacite. Elements analyzed are Mn, Ni, Cu, Zn, Ga, Rb, Sr, Y, Zr, Pb, and Sn (in spinels only). The data are used to calculate two sets of partition coefficients, one set based on the ratio of element in mineral/element in coexisting glass. The second set of coefficients, thought to be more robust, is corrected by application of the Rayleigh fractionation equations, which requires additional use of modal data. Data are presented for phenocryst core-rim phases and microphenocryst-groundmass phases from a few samples. Comparison with published coefficients reveals an overall consistency with those presented here, but with some notable anomalies. Examples are relatively high Zr values for pyroxenes and abnormally low Mn values in olivines and clinopyroxenes from Site 839 lavas. Some anomalies may reflect kinetic effects, but interpretation of the coefficients is complicated, especially in olivines from Sites 836 and 839, by possible crystal-liquid disequilibrium resulting from mixing processes.

Geochemistry of minerals from lavas of ODP Leg 135 holes

We use Nomarski differential interference contrast imaging to reveal the wealth of complex detail in plagioclase zoning for selected samples from Sites 834, 839, and 841. All sites contain some plagioclase with the very complex internal core zoning, convolute zoning, or very fine-scale euhedral oscillatory zoning of the sort generally considered typical of island-arc volcanic rocks. Plagioclase with contrasted zoning styles may coexist within a single lithologic unit or even within a single thin section. Especially notable is the presence of scattered plagioclase phenocrysts with complex zoning throughout Unit 7 in Hole 834B, which in other respects is relatively uniform in composition and appears to have had little or no differential sorting of crystals and liquid. Although our study is by no means comprehensive, it is sufficient to indicate that magmatic conditions have been variable during crystallization of these rocks, and mixing or at least minor contamination may be required to explain some of the relations observed. By analogy with experimental studies, it is possible that variations in water content, either over time or within different parts of a chamber or conduit system, have contributed to the observed contrasts in zoning.

Miocene to Pleistocene planktonic foraminifer biostratigraphy of ODP Leg 135 sites

Diverse and well-preserved planktonic foraminifers were recovered from six sites (834-839) drilled in the Lau Basin. Planktonic faunas from the Tongan Platform sites varied from those of the Lau Basin sites by being less well preserved (Site 840) to being very poorly preserved and very sparse (Site 841); at Site 841 most samples were barren. All sites penetrated a volcaniclastic sequence in which thick ash beds were encountered; foraminifer populations within the ash beds were often very small, making it difficult to obtain biostratigraphic data. No hiatuses were encountered in the upper Miocene to Pleistocene sections of the Lau Basin, but a possible break occurs at Site 840 on the Tongan Platform. Site 834 penetrated through a Quaternary-Pliocene sequence overlying basaltic basement, and topmost Miocene (Zone N17B) sediments interbedded within the volcanic sequence. Site 835 penetrated into the lower Pliocene (Zones N19 to N19-20). Site 836 penetrated the shortest section, with Zone N22 {Globorotalia (Truncorotalia) crassaformis hessi Subzone) directly overlying basalts. Site 837 penetrated into the basal part of Zone N22 (Globigerinoides quadrilobatus fistulosus Subzone) overlying basalt. Site 838 failed to encounter basalts, with the oldest sediment being from Zone N22 (Globigerinoides quadrilobatus fistulosus Subzone). Site 839, within the same basin as Site 838, located Zone N22 (Globigerinoides quadrilobatus fistulosus Subzone) sediments directly overlying igneous basement. Site 840 penetrated into the upper Miocene Zone N17A without encountering any major unconformity. Site 841, studied mainly from core-catcher samples, penetrated a Quaternary to questionable upper Miocene sequence that was in fault contact with middle Miocene (Zones N8 to N9) sediments. For the Lau Basin sites, reworking was encountered only in Sites 834 and 835. Site 834 was drilled adjacent to the Lau Ridge, on which are developed numerous reef al and shallow-water environments, where erosional conditions could have been expected during sea-level lowstands. Site 835 was drilled in a narrow basin that has been remote from these erosional influences; slumping and erosion of material from the adjacent basin slopes appears to have been the source of the reworking. For the Tongan Platform sites, reworking was observed only in the lower part of the upper Miocene section at Site 841, where late Eocene larger foraminifers are present in conglomerates and grits. The presence of Globorotalia (Globorotalia) multicamerata and small specimens of Sphaeroidinellopsis spp. in the Pleistocene of Site 840 may indicate reworking, but this is not clear. Unit I, which marks a reduction in volcanic activity in the Lau Basin, ranges in age from the lower part of Zone N22 (Globigerinoides quadrilobatus fistulosus Subzone) at Sites 834 and 835, to within Zone N22 (Globorotalia crassaformis hessi Subzone) at Sites 836 to 838, and within the upper part of Zone N22 (Bolliella praeadamsi Subzone) at Site 839. Units II and III are generally represented by thick to very thick ash beds, which generally contain low-diversity and often poorly preserved assemblages. Igneous sources seem to have remained important contributors of sediment up to the present day.

Geochemistry of ODP Leg 135 basalts

Cr-spinels in cores drilled during Ocean Drilling Program Leg 135 exhibit wide variations in composition and morphology that reflect complex petrogenetic histories. These Cr-spinels are found within basaltic lava flows that erupted in north-trending sub-basins within the Lau Basin backarc. Cr-spinels from Sites 834 and 836 occur as euhedral groundmass grains and inclusions in plagioclase, and range up to 300 ?m in size. These Cr-spinels are similar in composition, morphology, and mode of occurrence to Cr-spinels found within depleted, N-type mid-ocean-ridge basalts (N-MORB), reflecting similar crystallization conditions and host lava composition to N-MORB. Their compositional range is relatively narrow, with Cr/(Cr + Al + Fe3+) (Cr#) and Mg/(Mg + Fe2+) (Mg#) varying from 0.38 to 0.48 and 0.56 to 0.72, respectively; like Cr-spinels from N-MORB, they contain low amounts of TiO2 (0.37%-1.05%) and Fe3+/(Cr + Al + Fe3+) (Fe3+#; <0.11). In contrast, Cr-spinels from Site 839 have much higher Cr# at a given Mg#, with Cr# varying from 0.52 to 0.76 and Mg# varying from 0.27 to 0.75. These Cr-spinels are similar in composition to those from primitive, boninitic or low-Al2O3 arc basalts, sharing their low TiO2 and Fe3+# (typically below 0.35% and 0.1, respectively for spinel grain interiors). Site 839 Cr-spinels occur as small (to 50 µm) euhedra within strongly zoned olivine or as unusually large (to 3 mm), euhedral to subhedral megacrysts. These megacrysts are strongly zoned in Mg#, but they display little zoning in Cr#, providing evidence of strong compositional disequilibria with the host melt. The magnesian cores of the megacrysts crystallized from primitive, near-primary melts derived from harzburgitic or highly depleted lherzolitic sources, and they provide evidence that the Site 839 spinel-bearing lavas were derived by the mixing of melt with a Mg# of 0.75-0.80 and evolved, Cr-spinel barren melt with a Mg# < 0.6 shortly before eruption.

Geochemistry of ODP Hole 135-839B lavas

Four petrographic lava types occur, ranging from aphyric to moderately phyric clinopyroxene-olivine tholeiitic basalts (Unit 1); olivine-clinopyroxene picritic basalts, sparsely to strongly olivine-phyric (Unit 3-type); olivine-clinopyroxene basalts (clinopyroxene dominant) (Unit 4); and moderately to strongly phyric two-pyroxene-plagioclase basaltic andesites (Unit 9-type). The olivine phyric lavas contain forsteritic olivines (extending to Fo92), and very magnesian Cr-rich spinels similar to those occurring in boninitic lavas. The basaltic andesites are mineralogically and petrographically indistinguishable from the modern Tofua Arc basaltic andesites, one notable feature being the highly calcic cores in plagioclase phenocrysts (up to An95). The forsteritic olivines, the Cr-spinels, and the calcic plagioclases are unlikely to have been precipitated in the lava compositions in which they occur, and are thought to have been incorporated from highly primitive melts by way of mixing processes (as advocated by Allan, this volume). Notwithstanding the evidence for mixing, the major element chemistries of the Unit 1- and Unit 9-type lavas are shown to be consistent with the derivation of the Unit 9-type basaltic andesites by means of fractional crystallization, through magmas of similar chemistry to Unit 1. Some trace element discrepancies in the modeling, and the relative volcanic stratigraphy of Site 839, however, preclude a direct liquid line of descent between the actual recovered units. Trace element data as well as TiO2 and Na2O data clearly illustrate the arc-like affinities of the magmas, with strong highfield-strength element depletion and large-ion-lithophile element enrichment. The abundance patterns are very close to those of the Tofua and Kermadec arc magmas, and also Valu Fa. Pb-, Sr-, and Nd-isotopic compositions indicate closest affinities with a "Pacific" MORB source, apparently characteristic of the western, older part of the Lau Basin. A subduction-related isotopic contribution is, however, inferred. The sources of the Site 839 magmas are thus inferred to be similar to, but less depleted geochemically, than those of the modern Tofua Arc magmas. The Site 839 sequence is interpreted as an older remnant of a volcanic construct of the "proto-Tofua arc", originally developed adjacent to the Tonga Ridge. Opening of the eastern Lau Basin, because of southward migrating propagators, has split and isolated the sequence, leaving it stranded within the modern Lau Basin.

(Table 1) Platinum group element abundanves in ODP Leg 135 samples

Ocean Drilling Program Leg 135 backarc basin lavas are characterized by anomalously high Au contents (1.0-11.4 ppb) and strongly fractionated relative platinum group element (PGE) abundances (Pd/Ir ratio, approximately 100). The Rh and Ir contents are very low, ranging from below detection (approximately 0.02 ppb) to 0.08 ppb. The Pd and Pt contents range from <0.3 to 4 ppb. Rh, Pd, and Pt values are consistently and significantly higher in Site 836 and 839 samples relative to those from Sites 834 and 835. Major, trace, and rare earth element (REE) data suggest Sites 836 and 839 have a more pronounced arc signature than Sites 834 and 835. No correlation exists between noble metal abundance and indices of alteration or fractionation (e.g., loss on ignition (LOI), Mg#, and Cr or Ni contents), suggesting that measured values and ratios are primary and reflect characteristics of the mantle source. The evaluation of Leg 135 noble metal data with respect to potential mantle-source components is hindered by the lack of data on magmas derived from such sources. However, analyses of the limited available data for the different magma types suggest that the characteristic enrichment of Leg 135 lavas in Au, relative to Pd and Cu, cannot be derived solely from simple MORB-type or ocean-island-type mantle, or mantle depleted by a previous melt extraction event. The Au-enriched signature of the Lau basin lavas could, however, be produced through the addition of a sedimentary component from the downgoing slab. Separation of Au from the PGE occurs within oceanic hydrothermal systems and gold values of the resultant precipitates are 2-3 orders of magnitude higher than other oceanic crustal components. Even small additions of this component from the downgoing oceanic crust to a supra-subduction zone mantle melt could account for the high mean Au/Pd ratios of the Leg 135 samples (Sites 834 and 835, Au/Pd = 5.04; Sites 836 and 839, Au/Pd = 2.26).