Aplicação da técnica de eletrofloculação utilizando corrente alternada de frequência variável no tratamento de água de produção da indústria do petróleo

O principal objetivo da tese está relacionado ao tratamento de águas oleosas através da eletrofloculação utilizando corrente alternada de frequência variável, o qual procurou explorar as potencialidades desta técnica. Com a crescente demanda por petróleo e seus derivados, é cada vez maior a produção dessas águas residuárias que, antes de serem descartadas, precisam ser submetidas a tratamento que satisfaçam aos requisitos legais. O trabalho apresentado descreve o levantamento bibliográfico e os resultados dos ensaios realizados, empregando o tratamento de eletrofloculação com a finalidade de remover as substâncias consideradas poluentes presentes nestes efluentes. O processo de eletrofloculação foi testado tanto para o tratamento em corrente continua quanto em corrente alternada de frequência variável em efluentes sintéticos e reais de alta salinidade, contendo teores elevados de óleos e graxas, turbidez e cor. Eficiências de redução de 99% para óleos e graxas, cor e turbidez foram obtidos utilizando eletrodos de alumínio. O processo de eletrofloculação demonstrou-se bastante vantajoso em função da alta condutividade que permite o tratamento com menor consumo energético. A tecnologia de eletrofloculação com corrente alternada quando comparada com a tecnologia de corrente contínua se mostrou muito eficiente em relação a economia no desgaste de massa de eletrodos, o que, dependendo do tempo de aplicação da corrente elétrica nas mesmas condições de estudo, houve redução de mais da metade do consumo.

Determinação da fração lábil de Ba em água produzida de petróleo utilizando a técnica de difusão em filmes finos por gradiente de concentração com a membrana fosfato de celulose (P81) como agente ligante

Pós-graduação em Geociências e Meio Ambiente - IGCE

Determinação de metais em água produzida de petróleo

In order to enable the reuse of the large surplus volume of petroleum produced water for irrigation of crops inedible, the quality evaluation of this water is very important. This work aimed to evaluate the effectiveness of the diffusive gradient in thin films technique (DGT) for the determination of labile Cu (II), Mn (II) and Zn (II) in petroleum produced water destined to reuse in agriculture. Samples were collected at the exit of the wastewater treatment plant (WWTP) (after separation oil/water and flotation) of a Petrobrás onshore production region. Basically, the laboratory experiments with DGT devices involved the evaluation of the behavior of the main variables of the technique for determination of analytes in the samples (diffusion coefficients, immersion time, fractionation of organic and inorganic species, and performance of diffusion gels with different porosities, among others). Also, experiments were conducted based on the solid phase extraction (SPE) protocol with Chelex- 100 resin using previously established protocols to support the study. During the project the possibility of in situ immersions in water treatment plants was evaluated. The DGT technique presented satisfactory results for determination of Mn in produced water, and can be used for in situ determinations. However, the results obtained for Cu and Zn show the need of additional studies

Estudos hidroquímicos da água produzida de um determinado campo de petróleo da bacia potiguar

Waste generated during the exploration and production of oil, water stands out due to various factors including the volume generated, the salt content, the presence of oil and chemicals and the water associated with oil is called produced water. The chemical composition of water is complex and depends strongly on the field generator, because it was in contact with the geological formation for thousands of years. This work aims to characterize the hydrochemical water produced in different areas of a field located in the Potiguar Basin. We collected 27 samples from 06 zones (400, 600, 400/600, 400/450/500, 350/400, A) the producing field called S and measured 50 required parameter divided between physical and chemical parameters, cations and anions. In hydrochemical characterization was used as tools of reasons ionic calculations, diagrams and they hydrochemical classification diagram Piper and Stiff diagram and also the statistic that helped in the identification of signature patterns for each production area including the area that supplies water injected this field for secondary oil recovery. The ionic balance error was calculated to assess the quality of the results of the analysis that was considered good, because 89% of the samples were below 5% error. Hydrochemical diagrams classified the waters as sodium chloride, with the exception of samples from Area A, from the injection well, which were classified as sodium bicarbonate. Through descriptive analysis and discriminant analysis was possible to obtain a function that differs chemically production areas, this function had a good hit rate of classification was 85%

Seleção de bactérias fenololíticas para tratamento de efluentes de refinarias de petróleo

Os efluentes de indústrias, como refinarias e petroquímicas, frequentemente contém elevadas concentrações de substâncias tóxicas, dentre elas, os compostos fenólicos. Estas substâncias, mesmo em pequenas quantidades, afetam as propriedades organolépticas da água, além de que durante o processo de cloração da água potável, podem ser transformadas em clorofenóis e policlorofenóis, pela reação com o cloro, formando substâncias com características carcinogênicas. Neste sentido, o refino do petróleo produz grande variedade de poluentes cujas propriedades modificam-se em função dos processos utilizados. Os fenóis são compostos tóxicos, com características fungicida e desinfetante, sendo tóxico para a maioria dos microrganismos, além de apresentarem ação de carcinogenicidade, mutagenicidade e serem recalcitrantes, acumulam-se nos corpos receptores, gerando danos à saúde e à vida aquática. No entanto, embora o fenol possua ação bactericida, alguns microrganismos adquiriram a habilidade de se adaptar e utilizar este composto como fonte de carbono e energia. O presente trabalho pretendeu selecionar linhagens bacterianas, a partir do efluente de uma refinaria de petróleo, da região de Paulínia – SP, que sejam capazes de utilizar altos teores de fenóis como fonte de carbono e energia para seu crescimento e desenvolvimento, a fim de serem aplicadas nas estações de tratamento de efluentes industriais, com foco nas refinarias de petróleo. Foram isoladas 3 linhagens a partir das amostras enriquecidas do efluente da refinaria e, após os ensaios, constatou-se que 1 linhagem apresentou resistência à concentração de fenol de 1.000 mg.L-1. Os ensaios de biodegradação e crescimento em fenol como única fonte de carbono, demonstraram que estas linhagens são capazes de biodegradar aproximadamente 20% do fenol disponível no meio, no período de 24 horas. A quantificação do fenol residual foi realizada em...

Colunas de Winogradsky com águas contaminadas por petróleo e derivados monitoradas por ensaios ecotoxicológicos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Colunas de Winogradsky com águas contaminadas por petróleo e derivados monitoradas por ensaios ecotoxicológicos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influência da absorção de umidade no comportamento mecânico nos compósitos poliméricos híbridos Kevlar/vidro quando imerso em água do mar e petróleo

The polymer matrix composite materials are being used on a large scale in the most different industrial fields such as aerospace, automotive, oil, among others, since the industrial perspectives is currently working with materials which have a good mechanical performance at high service life and cost / benefit. Thus, the determination of the mechanical properties is indispensable for the characterization of waste resulting in greater expansion of this type of material. Thus, this work will be obtained three plates laminated with tereftálica polymeric matrix reinforced by a bidirectional woven E-glass and kevlar both industrially made, where the plates are manufactured by manual lamination process (hand lay-up), all laminates have five enhancement layers, the first hybrid laminate will consist of bidirectional woven E-glass fiber, kevlar fiber interspersed with layers, is formed by the second bidirectional woven kevlar fiber at the ends of the laminate (two layers), and in the center the glass fiber fabric (three layers), the third plate is composed of only the bidirectional woven E-glass fiber. Then were prepared specimens (CP) by standard, to determine the mechanical properties of tensile and bending in three points. After fabrication of the specimens, they were immersed in oil and seawater. After that, there was a comparison of the mechanical properties for the test condition in the dry state. Showing that there was a considerable increase in the properties studied because the effect of hybridization in laminates.

Estudos hidroquímicos da água produzida de um determinado campo de petróleo da bacia potiguar

Waste generated during the exploration and production of oil, water stands out due to various factors including the volume generated, the salt content, the presence of oil and chemicals and the water associated with oil is called produced water. The chemical composition of water is complex and depends strongly on the field generator, because it was in contact with the geological formation for thousands of years. This work aims to characterize the hydrochemical water produced in different areas of a field located in the Potiguar Basin. We collected 27 samples from 06 zones (400, 600, 400/600, 400/450/500, 350/400, A) the producing field called S and measured 50 required parameter divided between physical and chemical parameters, cations and anions. In hydrochemical characterization was used as tools of reasons ionic calculations, diagrams and they hydrochemical classification diagram Piper and Stiff diagram and also the statistic that helped in the identification of signature patterns for each production area including the area that supplies water injected this field for secondary oil recovery. The ionic balance error was calculated to assess the quality of the results of the analysis that was considered good, because 89% of the samples were below 5% error. Hydrochemical diagrams classified the waters as sodium chloride, with the exception of samples from Area A, from the injection well, which were classified as sodium bicarbonate. Through descriptive analysis and discriminant analysis was possible to obtain a function that differs chemically production areas, this function had a good hit rate of classification was 85%

Remoção conjugada de metais e óleo de água produzida

Petroleum can be associated or not with natural gas, but in both cases water is always present in its formation. The presence of water causes several problems, such as the difficulty of removing the petroleum from the reservoir rock and the formation of waterin-oil and oil-in-water emulsions. The produced water causes environmental problems, which should be solved to reduce the effect of petroleum industry in the environment. The main objective of this work is to remove simultaneously from the produced water the dispersed petroleum and dissolved metals. The process is made possible through the use of anionic surfactants that with its hydrophilic heads interacts with ionized metals and with its lipophilic tails interacts with the oil. The studied metals were: calcium, magnesium, barium, and cadmium. The surfactants used in this research were derived from: soy oil, sunflower oil, coconut oil, and a soap obtained from a mixture of 5wt.% coconut oil and 95wt.% animal fat. It was used a sample of produced water from Terminal de São Sebastião, São Paulo. As the concentration of the studied metals in produced water presented values close to 300 mg/L, it was decided to use this concentration as reference for the development of this research. Molecular absorption and atomic absorption spectroscopy were used to determine petroleum and metals concentrations in the water sample, respectively. A constant pressure filtration system was used to promote the separation of solid and liquid phases. To represent the behavior of the studied systems it was developed an equilibrium model and a mathematical one. The obtained results showed that all used surfactants presented similar behavior with relation to metals extraction, being selected the surfactant derived from soy oil for this purpose. The values of the partition coefficients between the solid and liquid phases " D " for the studied metals varied from 0.2 to 1.1, while the coefficients for equilibrium model " K " varied from 0.0002 and 0.0009. The removal percentile for oil with all metals associated was near 100%, showing the efficiency of the process

Tratamento eletroquímico de água produzida sintética para remoção de hidrocarbonetos policíclicos aromáticos

The aim of this work is the treatment of produced water from oil by using electrochemical technology. Produced water is a major waste generated during the process of exploration and production in the oil industry. Several approaches are being studied aiming at the treatment of this effluent; among them can be cited the biological process and chemical treatments such as advanced oxidation process and electrochemical treatments (electrooxidation, electroflotation, electrocoagulation, electrocoagulation). This work studies the application of electrochemical technology in the treatment of the synthetic produced water effluent through the action of the electron, in order to remove or transform the toxic and harmful substances from the environment by redox reactions in less toxic substances. For this reason, we used a synthetic wastewater, containing a mixture H2SO4 0,5M and 16 HPAs, which are: naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, benzo (a) anthracene, chrysene, benzo(b)fluoranthene, benzo(k) fluoranthene, benzo(a)pyrene, indeno(1,2,3-cd)pyrene, dibenzo(a, h)anthracene, benzo(g, h, i)perylene. Bulk electrochemical oxidation experiments were performed using a batch electrochemical reactor containing a pair of parallel electrodes, coupled with a power supply using a magnetic stirrer for favoring the transfer mass control. As anodic material was used, a Dimensionally Stable Anode (DSA) of Ti/Pt, while as cathode was used a Ti electrode. Several samples were collected at specific times and after that, the analysis of these samples were carried out by using Gas Chromatography Coupled to Mass Spectrometry (GC - MS) in order to determine the percentage of removal. The results showed that it was possible to achieve the removal of HPAs about 80% (in some cases, more than 80%). In addition, as an indicator of the economic feasibility of electrochemical treatment the energy consumption was analyzed for each hour of electrolysis, and based on the value kWh charged by ANEEL, the costs were estimated. Thus, the treatment costs of this research were quite attractive

Diagnóstico da qualidade da água na microbacia do córrego recanto, em americana, no estado de São Paulo

The environmental degradation observed in the Piracicaba, Capivari and Jundiaí watershed has been one of the principal preoccupations of the environmental agencies in the state of São Paulo, Brazil. In this context, there is inserted the Americana county which is cut by streams of unsuitable quality for the human consumption and other uses. The main goal of the present work was evaluated the water quality of the Recanto Creek, affluent of the Quilombo stream, at the Americana county, state of São Paulo, Brazil. The research was developed in the period from March of 2007 to March of 2008, when it was measured the flow and the following physical-chemical water quality parameters: temperature; turbidity; pH; dissolved oxygen (OD); phosphorus (P); ammonia nitrogen (NH 4); nitrate (NO 3); chemical demand of oxygen (DQO), besides total coliforms. The results demonstrated a variation of the flow from 34.3 to 375.2 L s -1, during the evaluated period. The parameters dissolved oxygen, phosphorus, ammonia nitrogen and nitrate presented values out of the limits recommended for rivers of class 3, like the Recanto Creek, suggesting water pollution due to the organic matter disposal.

A poluição das águas do Rio Bauru vista sob a perspectiva da pedagogia histórico-crítica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Espacialização das estimativas de contaminação de água subterrânea por defensivos agrícolas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Dinâmica temporal da poluição fecal nas águas do Córrego Rico, manancial de abastecimento da cidade de Jaboticabal-SP

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)