Bamboo : a distinctive green fibre

This article reports the preliminary findings on the morphology, chemical structure, antimicrobial and UV-screening properties of bamboo fibres. Bamboo fibres provide a very promising alternative to other natural fibres by virtue of their distinctive characteristics such as eco-friendly farming, inherent antimicrobial, UV-protective and highly· breathable properties. However, these novel properties are moslly claimed by fibre manufacturers, with little scientific evidence.  Moreover, those properties may largely depend on the manufacturing process, which is not widely disclosed by the manufacturers, Common manufacturing processes may require the use of a large amount of chemicals which would not make the product truly eco-friendly. Therefore, there is a strong need for unbiased laboratory experiments being conducted in a rigorous manner to elucidate the origin of those unique properties of bamboo fibres and to develop new processing methods to effectively utilise the properties in the final products. This research is aimed to prove the unique characteristics of bamboo fibres scientifically and to develop an efficient manufacturing process, in order to establish the place of bamboo fibres as a novel green material.

Use of part records in Merino breeding programs - The inheritance of wool growth and fibre traits during different times of the year to determine their value in Merino breeding programs

Fibre diameter can vary dramatically along a wool staple, especially in the Mediterranean environment of southern Australia with its dry summers and abundance of green feed in spring. Other research results have shown a very low phenotypic correlation between fibre diameter grown between seasons. Many breeders use short staples to measure fibre diameter for breeding purposes and also to promote animals for sale. The effectiveness of this practice is determined by the relative response to selection by measuring fibre traits on a full 12 months wool staple as compared to measuring them only on part of a staple. If a high genetic correlation exists between the part record and the full record, then using part records may be acceptable to identify genetically superior animals. No information is available on the effectiveness of part records. This paper investigated whether wool growth and fibre diameter traits of Merino wool grown at different times of the year in a Mediterranean environment, are genetically the same trait, respectively. The work was carried out on about 7 dyebanded wool sections/animal.year, on ewes from weaning to hogget age, in the Katanning Merino resource flocks over 6 years. Relative clean wool growth of the different sections had very low heritability estimates of less than 0.10, and they were phenotypically and genetically poorly correlated with 6 or 12 months wool growth. This indicates that part record measurement of clean wool growth of these sections will be ineffective as indirect selection criteria to improve wool growth genetically. Staple length growth as measured by the length between dyebands, would be more effective with heritability estimates of between 0.20 and 0.30. However, these measurements were shown to have a low genetic correlation with wool grown for 12 months which implies that these staple length measurements would only be half as efficient as the wool weight for 6 or 12 months to improve total clean wool weight. Heritability estimates of fibre diameter, coefficient of variation of fibre diameter and fibre curvature were relatively high and were genetically and phenotypically highly correlated across sections. High positive phenotypic and genetic correlations were also found between fibre diameter, coefficient of variation of fibre diameter and fibre curvature of the different sections and similar measurements for wool grown over 6 or 12 months. Coefficient of variation of fibre diameter of the sections also had a moderate negative phenotypic and genetic correlation with staple strength of wool staples grown over 6 months indicating that coefficient of variation of fibre diameter of any section would be as good an indirect selection criterion to improve stable strength as coefficient of variation of fibre diameter for wool grown over 6 or 12 months. The results indicate that fibre diameter, coefficient of variation of fibre diameter and fibre curvature of wool grown over short periods of time have virtually the same heritability as that of wool grown over 12 months, and that the genetic correlation between fibre diameter, coefficient of variation of fibre diameter and fibre curvature on part and on full records is very high (rg > 0.85). This indicates that fibre diameter, coefficient of variation of fibre diameter and fibre curvature on part records can be used as selection criteria to improve these traits. However, part records of greasy and clean wool growth would be much less efficient than fleece weight for wool grown over 6 or 12 months because of the low heritability of part records and the low genetic correlation between these traits on part records and on wool grown for 12 months.

UV-blue upconverted emission from Nd3+-doped InF3-based heavy-metal fluoride glasses for blue upconversion fibre laser

We report spectral properties and thermal stability of Nd3+-doped InF3-based heavy-metal fluoride glasses. Fluoroindate glasses in the chemical compositions (in mol%) of (38-x)InF3-16BaF(2)-20ZnF(2)-20SrF(2)-3GdF(3)-1GaF(3-)2NaF-xNdF(3) (x = 0.1, 0.5, 1, 2, 3) have been prepared under a controlled atmosphere in a dry box. Strong UVblue upconversion emission from a green excitation wavelength has been observed and the involved mechanisms have been explained. Near-infrared emission occurs simultaneously upon excitation of the UV-blue upconversion emissions with a cw Ar(+)laser. The upconversion spectra have revealed four dominant emissions at 354, 380, 412 and 449 nm, which belong to the transitions of D-4(3/2) -> I-4(9/2), D-4(3/2) -> I-4(11/2) and P-2(3/2) -> I-4(9/2), D-4(3/2) -> I-4(13/2) and P-2(3/2) -> I-4(11/2), D-4(3/2) -> I-4(15/2) and P-2(3/2) -> I-4(13/2), respectively.

A sensitive fibre optic pH sensor using multiple sol–gel coatings

The fabrication and characterization of a fibre optic pH sensor based on evanescent wave absorption is presented. The unclad portion of a multi-mode optical fibre is coated with a pH sensitive dye, which is immobilized by the sol–gel route. The sensitivity of the device has been found to increase when multiple sol–gel coatings are used as the sensing region. The dynamic range and the temporal response of the sensor are investigated for two different dyes, namely bromocresol purple and bromocresol green. The performance of the device is evaluated in terms of the results obtained during actual measurements.

A sensitive fibre optic pH sensor using multiple sol–gel coatings

The fabrication and characterization of a fibre optic pH sensor based on evanescent wave absorption is presented. The unclad portion of a multi-mode optical fibre is coated with a pH sensitive dye, which is immobilized by the sol–gel route. The sensitivity of the device has been found to increase when multiple sol–gel coatings are used as the sensing region. The dynamic range and the temporal response of the sensor are investigated for two different dyes, namely bromocresol purple and bromocresol green. The performance of the device is evaluated in terms of the results obtained during actual measurements

A sensitive fibre optic pH sensor using multiple sol–gel coatings

The fabrication and characterization of a fibre optic pH sensor based on evanescent wave absorption is presented. The unclad portion of a multi-mode optical fibre is coated with a pH sensitive dye, which is immobilized by the sol–gel route. The sensitivity of the device has been found to increase when multiple sol–gel coatings are used as the sensing region. The dynamic range and the temporal response of the sensor are investigated for two different dyes, namely bromocresol purple and bromocresol green. The performance of the device is evaluated in terms of the results obtained during actual measurements

A sensitive fibre optic pH sensor using multiple sol-gel coatings

The fabrication and characterization of a fibre optic pH sensor based on evanescent wave absorption is presented. The unclad portion of a multi-mode optical fibre is coated with a pH sensitive dye, which is immobilized by the sol–gel route. The sensitivity of the device has been found to increase when multiple sol–gel coatings are used as the sensing region. The dynamic range and the temporal response of the sensor are investigated for two different dyes, namely bromocresol purple and bromocresol green. The performance of the device is evaluated in terms of the results obtained during actual measurements.

Evaluation of bast fibre retting systems on hemp

In this paper the effect of eight different retting methods on decorticated hemp skins were analyzed. The methods were taken from six publications that looked at the retting of different bast fibres such as ramie, flax and kenaf. The fibres were batch retted in a package dye-vat at 100oC under 2 bar of pressure. The rinsed fibres were opened twice using a Shirley cotton trash separator. The opened fibre was assessed for fibre width, fibre width variation, colour and handle. It was found that the fibre that had undergone chemical retting with 7% Sodium Hydroxide (NaOH) and 0.5% Sodium Sulphite (Na2SO3) had the best diameter (18.39 micron) and the best coefficient of variation of diameter (57.32%). The fibre that was processed with 7% Sodium Hydroxide (NaOH) and 0.5% Sodium Sulphite (Na2SO3) had the whitest colour (YI D1925 = 31.61). The method treated with 1% Sodium Hydroxide (NaOH) and 1% Sodium Sulphite (Na2SO3) had the softest handle and the method treated with 1% Sodium Hydroxide (NaOH) and pre-rinsed with 0.3% Hydrochloric Acid (HCl) showed the best conversion of decorticated skins into spin able fibre (33.9% of dry green skins). It was decided that method treated with 1% Sodium Hydroxide (NaOH) and pre-rinsed with 0.3% Hydrochloric Acid (HCl) had the best fineness of fibre micron, conversion to spin able fibre (33.9% of dry green skins), whitest colour (YI D1925 = 36.13) and softest handle for the cost of chemicals involved.

Predicting changes in lifestyle and clinical outcomes in preventing diabetes : The Greater Green Triangle Diabetes Prevention Project

Objectives : To analyse how psychosocial determinants of lifestyle changes targeted in the Greater Green Triangle Diabetes Prevention Project conducted in Southeast Australia in 2004–2006 predict changes in dietary behaviour and clinical risk factors.

Methods : A longitudinal pre-test and post-test study design was used. The group program was completed by 237 people at high risk of type 2 diabetes. Associations between changes in the variables were examined by structural equation modelling using a path model in which changes in psychological determinants for lifestyle predicted changes in dietary behaviours (fat and fibre intake), which subsequently predicted changes in waist circumference and other clinical outcomes. Standardised regression weights are presented, with β = ± 0.1 and β = ± 0.3 representing small and medium associations, respectively.

Results : Improvements in coping self-efficacy and planning predicted improvements in fat (β = − 0.15, p < 0.05 and β = − 0.32, p < 0.001, respectively) and fibre intake (β = 0.15, p < 0.05 and β = 0.23, p < 0.001, respectively) which in turn predicted improvements in waist circumference (β = 0.18, p < 0.01 and β = − 0.16, p < 0.05, respectively). Improvements in waist circumference predicted improvements in diastolic blood pressure (β = 0.13, p < 0.05), HDL (β = − 0.16, p < 0.05), triglycerides (β = 0.17, p < 0.01), and fasting glucose (β = 0.15, p < 0.05).

Conclusions : Psychological changes predicted behaviour changes, resulting in 12-month biophysical changes. The findings support the theoretical basis of the interventions.

High extinction ratio in-fibre polarisers based on 45° tilted fibre Bragg gratings

We report a near-ideal in-fiber polarizer implemented by use of 45° tilted fiber Bragg grating structures that are UV inscribed in hydrogenated Ge-doped fiber. We demonstrate a polarization-extinction ratio of 33 dB over a 100-nm operation range near 1550 nm. We further show an achievement of 99.5% degree of polarization for unpolarized light with these gratings. We also theoretically investigate tilted grating structures based on the Green's function calculation, therein revealing the unique polarization characteristics, which are in excellent agreement with experimental data.

All optical networking beyond 10 Gbits/s OTDM networks based on electro-optic modulators and fibre ring lasers

This thesis examines options for high capacity all optical networks. Specifically optical time division multiplexed (OTDM) networks based on electro-optic modulators are investigated experimentally, whilst comparisons with alternative approaches are carried out. It is intended that the thesis will form the basis of comparison between optical time division multiplexed networks and the more mature approach of wavelength division multiplexed networks. Following an introduction to optical networking concepts, the required component technologies are discussed. In particular various optical pulse sources are described with the demanding restrictions of optical multiplexing in mind. This is followed by a discussion of the construction of multiplexers and demultiplexers, including favoured techniques for high speed clock recovery. Theoretical treatments of the performance of Mach Zehnder and electroabsorption modulators support the design criteria that are established for the construction of simple optical time division multiplexed systems. Having established appropriate end terminals for an optical network, the thesis examines transmission issues associated with high speed RZ data signals. Propagation of RZ signals over both installed (standard fibre) and newly commissioned fibre routes are considered in turn. In the case of standard fibre systems, the use of dispersion compensation is summarised, and the application of mid span spectral inversion experimentally investigated. For green field sites, soliton like propagation of high speed data signals is demonstrated. In this case the particular restrictions of high speed soliton systems are discussed and experimentally investigated, namely the increasing impact of timing jitter and the downward pressure on repeater spacings due to the constraint of the average soliton model. These issues are each addressed through investigations of active soliton control for OTDM systems and through investigations of novel fibre types respectively. Finally the particularly remarkable networking potential of optical time division multiplexed systems is established, and infinite node cascadability using soliton control is demonstrated. A final comparison of the various technologies for optical multiplexing is presented in the conclusions, where the relative merits of the technologies for optical networking emerges as the key differentiator between technologies.

High extinction ratio in-fibre polarisers based on 45° tilted fibre Bragg gratings

We report a near-ideal in-fiber polarizer implemented by use of 45° tilted fiber Bragg grating structures that are UV inscribed in hydrogenated Ge-doped fiber. We demonstrate a polarization-extinction ratio of 33 dB over a 100-nm operation range near 1550 nm. We further show an achievement of 99.5% degree of polarization for unpolarized light with these gratings. We also theoretically investigate tilted grating structures based on the Green's function calculation, therein revealing the unique polarization characteristics, which are in excellent agreement with experimental data.