Pontas e adjuvantes no potencial risco de deriva em pulverizações de produtos fitossanitários

Pós-graduação em Agronomia (Proteção de Plantas) - FCA

Avaliação de medidores com múltiplas tomadas de pressão na macromedição em sistemas de água

Pós-graduação em Engenharia Civil - FEIS

Determinação da deriva da mistura 2,4-D e glyphosate com diferentes pontas de pulverização e adjuvantes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização funcional de adjuvantes em soluções aquosas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Construção e validação de um túnel de vento para ensaios de estimativa da deriva em pulverizações agrícolas

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Metodologia para aplicação de reuso e reengenharia nos softwares de aquisição e redução de dados de um túnel de vento

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Modelo dinâmico de um túnel de vento de sopro

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Potential of adjuvants to reduce drift in agricultural spraying

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

A laboratory evaluation of alcohols as attractants for the sandfly Lutzomyia longipalpis (Diptera: Psychodidae)

Background: The potential attraction from 1-octen-3-ol for sandflies has been documented; however, studies using other primary alcohols are limited.Findings: We used a wind tunnel to compare the activation and attractive behaviors in male and female Lutzomyia longipalpis using 1-octen-3-ol and three additional alcohols, 1-octanol, 1-heptanol and 1-nonanol at three different concentrations: neat (100%) and diluted in hexane (10% and 50%). The compounds 1-octen-3-ol and 1-nonanol induced a clear concentration-dependent activation and attraction response in females. In males, 1-octen-3-ol, 1-nonanol and 1-heptanol yielded the same results.Conclusions: L. longipalpis is attracted to 1-octen-3-ol, 1-nonanol and 1-heptanol, which are found in many plant volatiles.

Theoretical and experimental study of agricultural spraying using CFD

This paper presents a computational fluid dynamics (CFD) application about the axial fan design used in an agricultural spraying system with a theoretical and experimental analysis of comparative results between the characteristic curves of a fan for several rotations and numerical results for the influence of blade attack angle variation and optimization of the spraying system, both for a same rotation. Flow was considered three-dimensional, turbulent, isothermal, viscous and non-compressible in a steady state, disregarding any influence of the gravity field. The average turbulent field was obtained from the application of time average where the turbulence model required for closing the set of equations was the k-E model. Resolution of all connected phenomena was achieved with the help of a fluid dynamics computer, CFX, which uses the finite volumes technique as a numerical method. In order to validate the theoretical analysis, an experiment was conducted in a circular section of a horizontal wind tunnel, using a Pitot tube for pressure readings. The main results demonstrate that the methodology used, based on CFD techniques, is able to reproduce the phenomenological behavior of an axial fan in a spraying system because results were very reliable and similar to experimentally measured ones.

Projeto mecânico de um modelo para túnel de vento e validação de seus componentes à partir de simulações em software de elementos finitos

The objective of this study was to develop a model that allows testing in the wind tunnel at high angles of attack and validates its most critical components by analyzing the results of simulations in finite element software. During the project this structure suffered major loads identified during the flight conditions and, from these, we calculated the stresses in critical regions defined as the parts of the model that have higher failure probabilities. All aspects associated with Load methods, mesh refining and stress analysis were taken into account in this approach. The selection of the analysis software was based on project needs, seeking greater ease of modeling and simulation. We opted for the software ANSYS® since the entire project is being developed in CAD platforms enabling a friendly integration between software's modeling and analysis

Micro-extração em fase sólida (SPME) in situ e comparação de compostos voláteis em variedades de manga (Mangifera indica L.) resistentes e suscetíveis à mosca-das-frutas Anastrepha obliqua (Macquart) (Diptera: Tephritidae)

Pós-graduação em Química - IQ

Spray adjuvant characteristics affecting agricultural spraying drift

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Interação pontas-adjuvantes na estimativa do risco potencial de deriva de pulverizações

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Concepção, modelagem, simulação e usinagem de um aerofólio automotivo auxiliado por computador

With the advancement of computer technology and the availability of technology computer aided design (CAD) errors in the designs are getting smaller. To this end the project aims to assess the reliability of the machine (CNC), which was designed by students of mechanical engineering college engineering - UNESP Bauru, by designing, modeling, simulation and machining an airfoil automotive. The profile template selected for the study will be a NACA 0012 machined plates in medium density fiberboard (MDF) and will be performed with a structural analysis simulation using finite elements and a software CFD (Computational Fluid Dynamics), and test the real scale model in a wind tunnel. The results obtained in the wind tunnel and CFD software will be compared to see the error in the machining process.