Boron nitride nanotubes : synthesis, characterization, functionalization, and potential applications

Boron nitride nanotubes (BNNTs) are structurally similar to carbon nanotubes (CNTs), but exhibit completely different physical and chemical properties. Thus, BNNTs with various interesting properties may be complementary to CNTs and provide an alternative perspective to be useful in different applications. However, synthesis of high quality of BNNTs is still challenging. Hence, the major goals of this research work focus on the fundamental study of synthesis, characterizations, functionalization, and explorations of potential applications. In this work, we have established a new growth vapor trapping (GVT) approach to produce high quality and quantity BNNTs on a Si substrate, by using a conventional tube furnace. This chemical vapor deposition (CVD) approach was conducted at a growth temperature of 1200 °C. As compared to other known approaches, our GVT technique is much simpler in experimental setup and requires relatively lower growth temperatures. The as-grown BNNTs are fully characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), electron energy loss spectroscopy (EELS), Energy Filtered Mapping, Raman spectroscopy, Fourier Transform Infra Red spectroscopy (FTIR), UV-Visible (UV-vis) absorption spectroscopy, etc. Following this success, the growth of BNNTs is now as convenient as growing CNTs and ZnO nanowires. Some important parameters have been identified to produce high-quality BNNTs on Si substrates. Furthermore, we have identified a series of effective catalysts for patterned growth of BNNTs at desirable or pre-defined locations. This catalytic CVD technique is achieved based on our finding that MgO, Ni or Fe are the good catalysts for the growth of BNNTs. The success of patterned growth not only explains the role of catalysts in the formation of BNNTs, this technique will also become technologically important for future device fabrication of BNNTs. Following our success in controlled growth of BNNTs on substrates, we have discovered the superhydrophobic behavior of these partially vertically aligned BNNTs. Since BNNTs are chemically inert, resistive to oxidation up to ~1000°C, and transparent to UV-visible light, our discovery suggests that BNNTs could be useful as self-cleaning, insulating and protective coatings under rigorous chemical and thermal conditions. We have also established various approaches to functionalize BNNTs with polymeric molecules and carbon coatings. First, we showed that BNNTs can be functionalized by mPEG-DSPE (Polyethylene glycol-1,2-distearoyl-sn-glycero-3-phosphoethanolamine), a bio-compatible polymer that helps disperse and dissolve BNNTs in water solution. Furthermore, well-dispersed BNNTs in water can be cut from its original length of >10µm to(>20hrs). This success is an essential step to implement BNNTs in biomedical applications. On the other hand, we have also succeeded to functionalize BNNTs with various conjugated polymers. This success enables the dispersion of BNNTs in organic solvents instead of water. Our approaches are useful for applications of BNNTs in high-strength composites. In addition, we have also functionalized BNNTs with carbon decoration. This was performed by introducing methane (CH4) gas into the growth process of BNNT. Graphitic carbon coatings can be deposited on the side wall of BNNTs with thicknesses ranging from 2 to 5 nm. This success can modulate the conductivity of pure BNNTs from insulating to weakly electrically conductive. Finally, efforts were devoted to explore the application of the wide bandgap BNNTs in solar-blind deep UV (DUV) photo-detectors. We found that photoelectric current generated by the DUV light was dominated in the microelectrodes of our devices. The contribution of photocurrent from BNNTs is not significant if there is any. Implication from these preliminary experiments and potential future work are discussed.

Granulometry, biogenic silica content, magnetic susceptibility and bulk densities of ODP Site 188-1165

The Prydz Bay area is a key region for studying and understanding the history of the eastern Antarctic Continental Ice Sheet (O'Brien, Cooper, Richter, et al., 2001, doi:10.2973/odp.proc.ir.188.2001). Ocean Drilling Program (ODP) Site 1165 is situated in a water depth of 3357 m on the continental rise offshore from Prydz Bay and lies in front of the outlet for the Lambert Glacier-Amery Ice Shelf system that today drains 22% of East Antarctica. The site was drilled into mixed pelagic and hemipelagic sediments from the southwestern side of the Wild Drift. The drift is an elongate sediment body formed by the interaction of sediment supplied from continental shelf and slope with westward-flowing bottom currents. The sedimentary sequence is characterized by alternations between a generally gray to dark gray facies and a green to greenish gray facies. The greenish facies are structureless diatom-bearing clays with common bioturbation and larger amounts (>15%-20%) of biogenic silica, dispersed clasts, and lonestones than the dark gray facies, which are mostly less bioturbated clay with some silt laminations (Shipboard Scientific Party, 2001, doi:10.2973/odp.proc.ir.188.103.2001). High-quality advanced piston corer and extended core barrel cores containing nearly complete sections of middle Miocene to early Pliocene age allow a detailed characterization of sedimentary cycles and can provide indications for ice advances of the Lambert Glacier system into Prydz Bay, for the extent of sea ice, and for changes in oceanic circulation. The purpose of this work is to provide a data set of coarse-fraction mass percentage (>63, >125, and >250 µm) and biogenic silica content measured on sediments of late Miocene to early Pliocene age drilled at Site 1165. Additionally, high-resolution records of magnetic susceptibility (MS) and gamma ray attenuation (GRA) bulk density are presented. These shipboard data sets were edited postcruise. Furthermore, I provide a high-resolution dry bulk density record that is derived from GRA bulk density and can be used for the calculation of mass accumulation rates. These sedimentological and physical parameters will be used in future work to understand the depositional pattern of alternating biogenic and terrigenous sediments that was observed at Site 1165 (Shipboard Scientific Party, 2001, doi:10.2973/odp.proc.ir.188.103.2001).

Single-walled carbon nanotube buckypapers as electrocatalyst supports for methanol oxidation

This work studies the use of various single-walled carbon nanotube (SWCNT) buckypapers as catalyst supports for methanol electro-oxidation in acid media. Buckypapers were obtained by vacuum filtration from pristine and oxidized SWCNT suspensions in different liquid media. Pt–Ru catalysts supported on the buckypapers were prepared by multiple potentiostatic pulses using a diluted solution of Pt and Ru salts (2 mM H2PtCl6 + 2 mM RuCl3) in acid media. The resulting materials were characterized via SEM, TEM, EDX and ICP-OES analysis. Well dispersed rounded nanoparticles between 2 and 15 nm were successfully electrodeposited on the SWCNT buckypapers. The ruthenium content in the bimetallic deposits was between 32 and 48 at. %, while the specific surface areas of the catalysts were in the range of 72–113 m2 g−1. It was found that the solvent used to prepare the SWCNT buckypaper films has a strong influence on the catalyst dispersion, particle size and metal loading. Cyclic voltammetry and chronoamperometry experiments point out that the most active electrodes for methanol electro-oxidation were prepared with the buckypaper supports that were obtained from SWCNT dispersions in N-methyl-pyrrolidone.

Preparation, characterisation and testing of CuO/Ce0.8Zr0.2O2 catalysts for NO oxidation to NO2 and mild temperature diesel soot combustion

CuO/ceria-zirconia catalysts have been prepared, deeply characterised (N2 adsorption–desorption isotherms at −196 °C, XRD, Raman spectroscopy, XPS, TEM and H2-TPR) and tested for NO oxidation to NO2 in TPR conditions, and for soot combustion at mild temperature (400 °C) in a NOx/O2 stream. The behaviour has been compared to that of a reference Pt/alumina commercial catalyst. The ceria-zirconia support was prepared by the co-precipitation method, and different amounts of copper (0.5, 1, 2, 4 and 6 wt%) were loaded by incipient wetness impregnation. The results revealed that copper is well-dispersed onto the ceria-zirconia support for the catalysts with low copper loading and CuO particles were only identified by XRD in samples with 4 and 6% of copper. A very low loading of copper increases significantly the activity for the NO oxidation to NO2 with regard to the ceria-zirconia support and an optimum was found for a 4% CuO/ceria-zirconia composition, showing a very high activity (54% at 348 °C). The soot combustion rate at 400 °C obtained with the 2% CuO/ceria-zirconia catalyst is slightly lower to that of 1% Pt/alumina in terms of mass of catalyst but higher in terms of price of catalyst.

Análisis de las relaciones morfología-propiedades en nanocompuestos basados en matrices de copolímeros de bloque

El objetivo principal de la presente investigación ha sido desarrollar una nueva clase de materiales nanocompuestos orgánicos-inorgánicos basados en la capacidad de los copolímeros de bloque de auto-organizarse promoviendo la dispersión de nanopartículas, así como relacionar las diferentes morfologías obtenidas con las propiedades finales de los nanocompuestos. Para generar la nanoestructuración de estos nanocompuestos basados en copolímeros de bloque, como el poli(estireno-b-isopreno-b-estireno) (SIS) y el poli(estireno-b-butadieno-b-estireno) (SBS) en nanopartículas de plata, se han utilizado los conceptos de compatibilización y confinamiento. Es decir, las nanopartículas inorgánicas se confinaron en una sola fase del copolímero de bloque mediante tratamientos superficiales y su funcionalización física. En particular, se utilizaron surfactantes (el cloruro de tetrametilamonio, TMAC, y el dodecanotiol, DT) para favorecer la interacción entre las nanopartículas inorgánicas y la matriz polimérica. Teniendo en cuenta los cálculos teóricos de los parámetros de solubilidad obtenidos mediante la teoría de Hoftizer-Van Krevelen, y la electronegatividad propia de los diferentes elementos, los dos surfactantes elegidos tienen una muy buena compatibilidad con el bloque de estireno favoreciendo la localización de las nanopartículas de plata en este bloque.

Electrospinning of silica sub-microtubes mats with platinum nanoparticles for NO catalytic reduction

Silica sub-microtubes loaded with platinum nanoparticles have been prepared in flexible non-woven mats using co-axial electrospinning technique. A partially gelated sol made from tetraethyl orthosilicate was used as the silica precursor, and oil was used as the sacrificial template for the hollow channel generation. Platinum has been supported on the wall of the tubes just adding the metallic precursor to the sol–gel, thus obtaining the supported catalyst by one-pot method. The silica tubes have a high aspect ratio with external/internal diameters of 400/200 nm and well-dispersed platinum nanoparticles of around 2 nm. This catalyst showed a high NO conversion with very high selectivity to N2 at mild conditions in the presence of excess oxygen when using C3H6 as reducing agent. This relevant result reveals the potential of this technique to produce nanostructured catalysts onto easy to handle conformations.

Effect of salinity on growth, pigmentation, N2 fixation and alkaline phosphatase activity of cultured Trichodesmium sp

Trichodesmium sp. isolated from the Great Barrier Reef lagoon was cultured in artificial seawater media containing a range of salinities. Trichodesmium sp. actively grew over a wide range of salinities (22 to 43 psu) and hence can be classed as euryhaline. Maximum growth occurred with salinities in the range 33 to 37 psu. Chl a content and alkaline phosphatase activity were found to increase with salinity over the range 22 to 43 psu, but the N-2 fixation rate was reduced at salinities below and above the range for maximum growth. Growth in media exhibiting maximum growth was characterised by well-dispersed cultures of filaments, while significant aggregations of filaments formed in other media. It is proposed that the tendency for Trichodesmium filaments to aggregate in media with salinities outside the range for maximum growth is an opportunistic response to a deficiency of cellular nitrogen, which results from the reduced N-2 fixation rates, and the aggregation occurs in order to enhance the uptake of combined N released within the aggregates and/or the N-2 fixation within the aggregates.

The influence of strontium on porosity formation in Al-Si alloys

Strontium modification is known to alter the amount, characteristics, and distribution of porosity in Al-Si castings. Although many theories have been proposed to account for these effects, most can be considered inadequate because of their failure to resolve contradictions and discrepancies in the literature. In an attempt to critically appraise some of these theories, the amount, distribution, and morphology of porosity were examined in sand-cast plates of Sr-free and Sr-containing pure Al, Al-l wt pet Si, and Al-9 wt pet Si alloys. Statistical significance testing was used to verify apparent trends in the porosity data. No apparent differences in the amount, distribution, and morphology of porosity were observed between Sr-free and Sr-containing alloys with no or very small eutectic volume fractions. However, Sr modification significantly changed the amount, distribution, and morphology of porosity in alloys with a significant volume fraction of eutectic. ne addition of Sr reduced porosity in the hot spot region of the casting, and the pores became well dispersed and rounded. This result can be explained by considering the combined effect of the casting design and the differences in the pattern of eutectic solidification between unmodified and Sr-modified alloys.

Influence of particle morphology on nanostructural feature and conducting property in Sm-doped CeO2 sintered body

Doped ceria (CeO2,) compounds are fluorite type oxides, which show oxide ionic conductivity higher than yttria stabilized zirconia (YSZ), in oxidizing atmospheres. As a consequence of this, considerable interest has been shown in application of these materials for 'low (500-650 degreesC)' or 'intermediate (650-800 degreesC)' temperature operation, solid oxide fuel cells (SOFCs). In this study, the authors prepared two kinds of nanosize Sm-doped CeO2 particles with different morphologies: one type was round and the other was elongated. Processing these powders with different morphology produced dense materials with very different ionic conducting properties and different nanoscale microstructures. Since both particles are very fine and well dispersed, sintered bodies with high density (relative density >95% of theoretical) could be prepared using both types of powder particles. The electrical conductivity of sintered bodies prepared from these powders with different starting morphologies was very different. Materials prepared from particles having a round shape were much higher than those produced using powders with an elongated morphology. Measured activation energies of the corresponding sintered samples showed a similar trend; round particles (60 kJ/mol), elongated particles (74 kJ/mol). While X-ray diffraction (XRD) profiles of these sintered materials were identical, diffuse scatter was observed in the back.-round of selected area electron diffraction pattern recorded from both sintered bodies. This indicated an underlying structure that appeared to have been influenced by the processing technology. Detailed observation using high-resolution transmission electron microscopy (HR-TEM) revealed that the size of microdomain with ordering of cations in the sintered body made from round shape particles was much smaller than that of the sintered body made from elongated particles. Accordingly, it is concluded that the morphology of doped CeO2 powders strongly influenced the microdomain size and electrolytic properties in the doped CeO2 sintered body. (C) 2004 Elsevier B.V. All rights reserved.

Porous tin film synthesized by electrodeposition and the electrochemical performance for lithium-ion batteries

Porous tin films as anode for lithium-ion batteries are electrodeposited on graphite paper. Homogeneous tin films with significant void space accommodate the volume change during tin lithiation/delithiation. Through adjusting the electrodeposition currents and time, the morphologies and void space of tin films on graphite paper are controllable. At fixed electrodeposition current densities, the prolonged electrodeposition time plays the role in growing big tin particles and resulting the disappearance of void space among tin particles. The increased electrodeposition current plays the role to increase the quantity of tin seeds in thickness of tin film, and the void space among tin particles remains but the thick film limits its electrochemical performance. The tin films electrodeposited at an optimized current densities and for an optimized electrodeposition time, present the best electrochemical performance, because the tin nanoparticles are well dispersed on graphite substrate including void space. The tin film electrodeposited at 0.2 A cm-2 for 2 min shows the capacity of 1.0 mAh cm-2 after 50 charge/discharge cycles. The void space of tin film is very important for the best capacity and cyclic ability. The metallic tin film produced at 0.4 A cm-2 for 3 min remains the uniform and microporous structure after charge/discharge for 50 cycles.

Novel Ni-Mg-Al-Ca catalyst for enhanced hydrogen production for the pyrolysis-gasification of a biomass/plastic mixture

A Ni-Mg-Al-Ca catalyst was prepared by a co-precipitation method for hydrogen production from polymeric materials. The prepared catalyst was designed for both the steam cracking of hydrocarbons and for the in situ absorption of CO2 via enhancement of the water-gas shift reaction. The influence of Ca content in the catalyst and catalyst calcination temperature in relation to the pyrolysis-gasification of a wood sawdust/polypropylene mixture was investigated. The highest hydrogen yield of 39.6molH2/g Ni with H2/CO ratio of 1.90 was obtained in the presence of the Ca containing catalyst of molar ratio Ni:Mg:Al:Ca=1:1:1:4, calcined at 500°C. In addition, thermogravimetric and morphology analyses of the reacted catalysts revealed that Ca introduction into the Ni-Mg-Al catalyst prevented the deposition of filamentous carbon on the catalyst surface. Furthermore, all metals were well dispersed in the catalyst after the pyrolysis-gasification process with 20-30nm of NiO sized particles observed after the gasification without significant aggregation.

Elettrodeposizione di catalizzatori a base di Rh su schiume e fibre metalliche di FeCrAlloy per la produzione di syngas

The preparation of structured catalysts active in the catalytic partial oxidation of methane to syngas, was performed by electrosynthesis of hydroxides on FeCrAlloy foams and fibers. Rh/Mg/Al hydrotalcite-type compounds were prepared by co-precipitation of metallic cations on the support and successive calcination. Electrochemical reactions have been studied during the electrodeposition by linear sweep voltammetry. The experiments were performed at supports immersed in KNO3, KCl, Mg2+ and Al3+ aqueous solutions, starting by different precursors (nitrate and chlorides salts) and modifying the Mg/A ratio. Rh/Mg/Al hydrotalcite-type compounds were deposited on metal foams by applying a -1.2V vs SCE potential for 2000s with a nitrate solution of 0.06M total metal concentration. Firstly it was studied the effect of Mg on the coating propierties, modifying the Rh/Mg/Al atomic ratio (5/70/25, 5/50/45, 5/25/70 e 5/0/95). Then the effect of the amount of Rh was later investigated in the sample with the largest Mg content (Rh/Mg/Al = 5/70/25 and 2/70/28).The results showed that magnesium allowed obtaining the most homogeneous and well adherent coatings, wherein rhodium was well dispersed. The sample with the Rh/Mg /Al ratio equal to5/70/25 showed the best catalytic performances. Decreasing the Rh content, the properties of the coating were not modified, but the catalytic activity was lower, due to a not enough number of active sites to convert the methane. The work on metal fibers focused on the effect of precursor concentration, keeping constant composition, potential and synthesis time at the values of Rh/Mg/Al =5/70/25, -1.2V vs SCE and 1000s. However fibers geometry did not allow to obtain a high quality coating, even if results were quite promising.

Physical and chemical kinetics of structural build-up of cement suspensions

Abstract : The structural build-up of fresh cement-based materials has a great impact on their structural performance after casting. Accordingly, the mixture design should be tailored to adapt the kinetics of build-up given the application on hand. The rate of structural build-up of cement-based suspensions at rest is a complex phenomenon affected by both physical and chemical structuration processes. The structuration kinetics are strongly dependent on the mixture’s composition, testing parameters, as well as the shear history. Accurate measurements of build-up rely on the efficiency of the applied pre-shear regime to achieve an initial well-dispersed state as well as the applied stress during the liquid-solid transition. Studying the physical and chemical mechanisms of build-up of cement suspensions at rest can enhance the fundamental understanding of this phenomenon. This can, therefore, allow a better control of the rheological and time-dependent properties of cement-based materials. The research focused on the use of dynamic rheology in investigating the kinetics of structural build-up of fresh cement pastes. The research program was conducted in three different phases. The first phase was devoted to evaluating the dispersing efficiency of various disruptive shear techniques. The investigated shearing profiles included rotational, oscillatory, and combination of both. The initial and final states of suspension’s structure, before and after disruption, were determined by applying a small-amplitude oscillatory shear (SAOS). The difference between the viscoelastic values before and after disruption was used to express the degree of dispersion. An efficient technique to disperse concentrated cement suspensions was developed. The second phase aimed to establish a rheometric approach to dissociate and monitor the individual physical and chemical mechanisms of build-up of cement paste. In this regard, the non-destructive dynamic rheometry was used to investigate the evolutions of both storage modulus and phase angle of inert calcium carbonate and cement suspensions. Two independent build-up indices were proposed. The structural build-up of various cement suspensions made with different cement contents, silica fume replacement percentages, and high-range water reducer dosages was evaluated using the proposed indices. These indices were then compared to the well-known thixotropic index (Athix.). Furthermore, the proposed indices were correlated to the decay in lateral pressure determined for various cement pastes cast in a pressure column. The proposed pre-shearing protocol and build-up indices (phases 1 and 2) were then used to investigate the effect of mixture’s parameters on the kinetics of structural build-up in phase 3. The investigated mixture’s parameters included cement content and fineness, alkali sulfate content, and temperature of cement suspension. Zeta potential, calorimetric, spectrometric measurements were performed to explore the corresponding microstructural changes in cement suspensions, such as inter-particle cohesion, rate of Brownian flocculation, and nucleation rate. A model linking the build-up indices and the microstructural characteristics was developed to predict the build-up behaviour of cement-based suspensions The obtained results showed that oscillatory shear may have a greater effect on dispersing concentrated cement suspension than the rotational shear. Furthermore, the increase in induced shear strain was found to enhance the breakdown of suspension’s structure until a critical point, after which thickening effects dominate. An effective dispersing method is then proposed. This consists of applying a rotational shear around the transitional value between the linear and non-linear variations of the apparent viscosity with shear rate, followed by an oscillatory shear at the crossover shear strain and high angular frequency of 100 rad/s. Investigating the evolutions of viscoelastic properties of inert calcite-based and cement suspensions and allowed establishing two independent build-up indices. The first one (the percolation time) can represent the rest time needed to form the elastic network. On the other hand, the second one (rigidification rate) can describe the increase in stress-bearing capacity of formed network due to cement hydration. In addition, results showed that combining the percolation time and the rigidification rate can provide deeper insight into the structuration process of cement suspensions. Furthermore, these indices were found to be well-correlated to the decay in the lateral pressure of cement suspensions. The variations of proposed build-up indices with mixture’s parameters showed that the percolation time is most likely controlled by the frequency of Brownian collisions, distance between dispersed particles, and intensity of cohesion between cement particles. On the other hand, a higher rigidification rate can be secured by increasing the number of contact points per unit volume of paste, nucleation rate of cement hydrates, and intensity of inter-particle cohesion.

Applications for nanomaterials in critical technologies

This thesis is devoted to the development, synthesis, properties, and applications of nano materials for critical technologies, including three areas: (1) Microbial contamination of drinking water is a serious problem of global significance. About 51% of the waterborne disease outbreaks in the United States can be attributed to contaminated ground water. Development of metal oxide nanoparticles, as viricidal materials is of technological and fundamental scientific importance. Nanoparticles with high surface areas and ultra small particle sizes have dramatically enhanced efficiency and capacity of virus inactivation, which cannot be achieved by their bulk counterparts. A series of metal oxide nanoparticles, such as iron oxide nanoparticles, zinc oxide nanoparticles and iron oxide-silver nanoparticles, coated on fiber substrates was developed in this research for evaluation of their viricidal activity. We also carried out XRD, TEM, SEM, XPS, surface area measurements, and zeta potential of these nanoparticles. MS2 virus inactivation experiments showed that these metal oxide nanoparticle coated fibers were extremely powerful viricidal materials. Results from this research suggest that zinc oxide nanoparticles with diameter of 3.5 nm, showing an isoelectric point (IEP) at 9.0, were well dispersed on fiberglass. These fibers offer an increase in capacity by orders of magnitude over all other materials. Compared to iron oxide nanoparticles, zinc oxide nanoparticles didn’t show an improvement in inactivation kinetics but inactivation capacities did increase by two orders of magnitude to 99.99%. Furthermore, zinc oxide nanoparticles have higher affinity to viruses than the iron oxide nanoparticles in presence of competing ions. The advantages of zinc oxide depend on high surface charge density, small nanoparticle sizes and capabilities of generating reactive oxygen species. The research at its present stage of development appears to offer the best avenue to remove viruses from water. Without additional chemicals and energy input, this system can be implemented by both points of use (POU) and large-scale use water treatment technology, which will have a significant impact on the water purification industry. (2) A new family of aliphatic polyester lubricants has been developed for use in micro-electromechanical systems (MEMS), specifically for hard disk drives that operate at high spindle speeds (>15000rpm). Our program was initiated to address current problems with spin-off of the perfluoroether (PFPE) lubricants. The new polyester lubricant appears to alleviate spin-off problems and at the same time improves the chemical and thermal stability. This new system provides a low cost alternative to PFPE along with improved adhesion to the substrates. In addition, it displays a much lower viscosity, which may be of importance to stiction related problems. The synthetic route is readily scalable in case additional interest emerges in other areas including small motors. (3) The demand for increased signal transmission speed and device density for the next generation of multilevel integrated circuits has placed stringent demands on materials performance. Currently, integration of the ultra low-k materials in dual Damascene processing requires chemical mechanical polishing (CMP) to planarize the copper. Unfortunately, none of the commercially proposed dielectric candidates display the desired mechanical and thermal properties for successful CMP. A new polydiacetylene thermosetting polymer (DEB-TEB), which displays a low dielectric constant (low-k) of 2.7, was recently developed. This novel material appears to offer the only avenue for designing an ultra low k dielectric (1.85k), which can still display the desired modulus (7.7Gpa) and hardness (2.0Gpa) sufficient to withstand the process of CMP. We focused on further characterization of the thermal properties of spin-on poly (DEB-TEB) ultra-thin film. These include the coefficient of thermal expansion (CTE), biaxial thermal stress, and thermal conductivity. Thus the CTE is 2.0*10-5K-1 in the perpendicular direction and 8.0*10-6 K-1 in the planar direction. The low CTE provides a better match to the Si substrate which minimizes interfacial stress and greatly enhances the reliability of the microprocessors. Initial experiments with oxygen plasma etching suggest a high probability of success for achieving vertical profiles.

Scaffolds porosos à base de fosfatos de cálcio para regeneração óssea

Graças ao aumento da esperança média de vida do ser humano, a engenharia de tecidos tem sido uma área alvo de enorme investigação. A utilização de estruturas tridimensionais porosas e biodegradáveis, denominadas de scaffolds, como matriz para a adesão e proliferação celular tem sido amplamente investigada. Existem atualmente diversas técnicas para a produção destas estruturas mas o grau de exigência tem vindo a aumentar, existindo ainda lacunas que necessitam ser preenchidas. A técnica de robocasting consiste numa deposição camada a camada de uma pasta coloidal, seguindo um modelo computorizado (CAD) e permite a produção de scaffolds com porosidade tamanho de poro e fração de porosidade controlados, boa reprodutibilidade, e com formas variadas, as quais podem ser idênticas às dos defeitos ósseos a preencher. O presente estudo teve como objetivo produzir scaffolds porosos à base de fosfatos de cálcio através de robocasting. Para tal, foram estudadas duas composições de pós à base de β-TCP, uma pura e outra co-dopada com estrôncio, zinco e manganês. Inicialmente os pós foram sintetizados pelo método de precipitação química por via húmida. Após a síntese, estes foram filtrados, secos, calcinados a 1000ºC e posteriormente moídos até possuírem um tamanho médio de partícula de cerca de 1,5 μm. Os pós foram depois peneirados com uma malha de 40μm e caracterizados. Posteriormente foram preparadas várias suspensões e avaliado o seu comportamento reológico, utilizando Targon 1128 como dispersante, Hidroxipropilmetilcelulose (HPMC) como ligante e polietilenimina (PEI) como agente floculante. Por fim, e escolhida a melhor composição para a formação da pasta, foram produzidos scaffolds com diferentes porosidades, num equipamento de deposição robótica (3D Inks, LLC). Os scaffolds obtidos foram secos à temperatura ambiente durante 48 horas, sinterizados a 1100ºC e posteriormente caracterizados por microscopia eletrónica de varrimento (SEM), avaliação dos tamanhos de poro, porosidade total e testes mecânicos. Ambas as composições estudadas puderam ser transformadas em pastas extrudíveis, mas a pasta da composição pura apresentou uma consistência mais próxima do ideal, tendo originado scaffolds de melhor qualidade em termos de microestrutura e de propriedades mecânicas.