Accelerated drying of plantation grown Eucalyptus cloeziana and Eucalyptus pellita sawn timber

The objective of this study was to gain an understanding for drying sawn timber produced from fast-grown, well-managed Queensland hardwood plantations using accelerated drying methods. Due to limited resources, this was a preliminary study and further work will be required to optimize schedules for industrial implementation. Three conventional kiln trials, including two for 38-mm-thick, 19-year-old plantation Gympie messmate (Eucalyptus cloeziana F. Muell.) and one for 25mm thick, 15-year-old plantation red mahogany (Eucalyptus pellita F. Muell.), and two vacuum kiln drying trials, one each for 38- and 25mm thick Gympie messmate, were conducted. Measurements of final cross-sectional moisture content, moisture content gradient, residual drying stress, and internal and surface checking were used to quantify dried quality. Drying schedules were chosen based on either existing published schedules or, in the case of the vacuum drying trials, existing schedules for species with similar wood density and dying degrade properties, or manipulated schedules based on the results of trials conducted during this study. The findings indicate that both species can be dried using conventional drying techniques with acceptable grade quality in approximately 75 percent of the drying time that industry is currently achieving when drying native forest timber of the same species. The vacuum drying time was 60 percent less than conventional drying for 38-mm-thick, 19-year-old Gympie messmate, although drying quality needs improving. The findings have shown that through careful schedule manipulation and adjustment, the grade quality can be optimized to suit the desired expectation. Additional research is required to further optimize the schedules to ensure acceptable grade qualities can be reliably achieved across all drying criteria and exploit opportunities to reduce drying times further.

Hydrofluoroalkanes as carrier solvents for timber preservation

Hydrofluoroalkanes are a specific category of hydrofluorocarbon (HFC) commonly used in refrigeration applications. Some HFCs hold potential for use as carrier fluids for preservatives used to protect timber above ground. They do not share the most significant disadvantages of currently used carriers for these applications. At ‘conventional’ operating pressures, they are capable of rapid, full penetration of some timbers generally considered refractory, such as spruce and the heartwood of radiata pine. But they are comparatively expensive and, while they are not detrimental to the ozone layer, they would contribute significantly to the greenhouse effect if released. Impregnation process conditions can be optimised to maximise biocide solubility and impregnation speed and depth.

Skin damage to two new mango cultivars during irradiation and cold storage.

Mangoes can express several skin disorders following important postharvest treatments. Responses are often cultivar specific. This paper reports the responses of two new Australian mango cultivars to some of these treatments. 'Honey Gold' mango develops "under skin browning" early during cold storage. This is thought to be partly caused by a discolouration of the latex vessels which then spreads to the surrounding cells. The symptoms appear to be worse in fruit from hotter production areas and that have been cooled to temperatures below 18C soon after harvest. Current commercial recommendations are to cool fruit to 18C, which limits postharvest handling options. Recent trials have confirmed that delayed or slowed cooling after harvest can reduce under skin browning. The defect may also be associated with physical injury to the skin during harvesting and packing. Irradiation is potentially an important disinfestation treatment for fruit fly in Australian mangoes. The 'B74' mango cultivar develops significant skin damage following irradiation, mainly due to discolouration of the cells surrounding the lenticels. Recent results confirmed that fruit harvested directly from the tree into trays without exposure to water or postharvest chemicals are not damaged by irradiation, while commercially harvested and packed fruit are damaged. Several major harvest and postharvest steps appear to increase lenticel sensitivity to irradiation. Further work is required to develop commercially acceptable protocols to facilitate 'Honey Gold' and 'B74' mango distribution and marketing.

Cultivar-specific effects of pathogen testing on storage root yield of sweetpotato, Ipomoea batatas.

The accumulation and perpetuation of viral pathogens over generations of clonal propagation in crop species such as sweetpotato, Ipomoea batatas, inevitably result in a reduction in crop yield and quality. This study was conducted at Bundaberg, Australia to compare the productivity of field-derived and pathogen-tested (PT) clones of 14 sweetpotato cultivars and the yield benefits of using healthy planting materials. The field-derived clonal materials were exposed to the endemic viruses, while the PT clones were subjected to thermotherapy and meristem-tip culture to eliminate viral pathogens. The plants were indexed for viruses using nitrocellulose membrane-enzyme-linked immunosorbent assay and graft-inoculations onto Ipomoea setosa. A net benefit of 38% in storage root yield was realised from using PT materials in this study. Conversely, in a similar study previously conducted at Kerevat, Papua New Guinea (PNG), a net deficit of 36% was realised. This reinforced our finding that the response to pathogen testing was cultivar dependent and that the PNG cultivars in these studies generally exhibited increased tolerance to the endemic viruses present at the respective trial sites as manifested in their lack of response from the use of PT clones. They may be useful sources for future resistance breeding efforts. Nonetheless, the potential economic gain from using PT stocks necessitates the use of pathogen testing on virus-susceptible commercial cultivars. .

Ce1-xRuxO2-delta (x=0.05, 0.10): A New High Oxygen Storage Material and Pt, Pd-Free Three-Way Catalyst

Nanocrystalline Ce1-xRuxO2-delta (x = 0.05 and 0.10) of 8-10 nm sizes have been synthesized by hydrothermal method using melamine as complexing agent. Compounds have been characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and energy-dispersive X-ray analysis (EDX) and their structures have been refined by the Rietveld method.The compounds crystallize in fluorite structure and the composition is Ce1-xRuxO2-x/2 where Ru is in +4 state and Ce is in mixed-valence (+3, +4) state. Substitution of Ru4+ ion in CeO2 activated the lattice oxygen. Ce1-xRuxO2-x/2 reversibly releases 0.22[O] and 0.42[O] for x = 0.05 and 0.10, respectively, which is higher than the maximumpossible OSC of 0.22 [O] observed for Ce0.50Zr0.50O2. Utilization of Higher OSC of Ce1-xRuxO2-delta (x = 0.05 and 0.10) is also reflected in terms of low-temperature CO oxidation with these catalysts, both in the presence and absence of feed oxygen. The Ru4+ ion acts as an active center for reducing molecules (CO, hydrocarbon ``HC'') and oxide ion vacancy acts as an active center for O-2 and NO, leading to low-temperature NO conversion to N-2. Thus due to Ru4+ ion, Ce1-xRuxO2-delta is not just a high oxygen storage material but also shows high activity toward CO, hydrocarbon ``HC'' oxidation, and NO reduction by CO at low temperature with high N-2 selectivity for three-way catalysis.

Improving added value and small medium enterprises capacity in the utilisation of plantation timber for furniture production in Jepara region

Improving added value and Small Medium Enterprises capacity in the utilisation of plantation timber for furniture production in Jepara region of Indonesia: improving recovery, design, manufacturing, R&D and training capacities.

Australian Timber Pole Resources for Energy Networks. A review

More than 5 million timber utility poles are currently in-service throughout Australia’s energy networks. Most were produced from select native forest-grown hardwood species having the required structural characteristics and naturally-durable heartwood. Anecdotal evidence suggests that up to 70% of the timber poles that are currently in-service were installed over the 20 years following the end of World War Two, and these poles are likely to require replacement or remedial maintenance over the next decade. The purposes of this review were to clarify the supply and demand situation for traditional timber poles, and to investigate alternatives in terms of their potential availability and suitability.

Evaluation of wood characteristics of tropical post-mid rotation plantation Eucalyptus cloeziana and E. pellita: Part (a) Natural durability of timber.

This project evaluated the timber quality, processing and performance characteristics of 19-year-old Eucalyptus cloeziana (Gympie messmate) and 15-year-old Eucalyptus pellita (red mahogany). Studies were undertaken to evaluate wood and mechanical properties, accelerated seasoning and veneer and plywood production. Above-ground and in-ground durability field tests were established at three locations in Queensland. Ground proixmity tests and L-joint tests were installed to gather data applicable to above-ground, weather-exposed end-use applications, and stake tests were installed to gather data applicable to in-ground, weather-exposed end-use applications.

Evaluation of wood characteristics of tropical post-mid rotation plantation Eucalyptus cloeziana and E. pellita: Part (b) Accelerated seasoning of sawn timber.

Drying trials were conducted using two species of plantation grown eucalypt timbers: 19-year-old Eucalyptus cloeziana (Gympie messmate) and 15-year-old Eucalyptus pellita (red mahogany). The objective of this study was to gain an understanding of the drying potential of young plantation grown material using accelerated seasoning methods, a process expected to be critcal to the success of plantation hardwood products entering value added markets. The findings are encouraging, indicating that both species can be dried using conventional drying techniques much faster than industry is currently achieving when drying native forest timber. The results suggest that there is a definite drying time advantatge in vacuum drying over conventional methods for 19-year-old E. cloeziana. The findings have shown that through careful schedule manipulation and adjustment, the grade quality can be optimised to suit the desired expectation. As this study was limited to only a small number of trials, time and quality improvements are expected to be realised for both conventional and vacuum drying methods as more research is conducted.

Australian hardwood drying best practice manual. Part 2

This manual is a guide to establishing a set of operations to achieve high grade results in product quality and recovery, flexibility, innovation, cost, and competitiveness. The manual outlines: - economic and feasible technologies for increasing recovery and reducing avoidable loss during processing, from the log to the finished board, and - mechanisms that allow production value to be optimised in different sized mills. Part 2 includes sections 8 to 17: Air drying, pre-drying, reconditioning, controlled final drying, dry milling, storage, information assessment, drying quality assessment, moisture content monitoring, glossary. Part 1 Link: http://era.deedi.qld.gov.au/3138 Covers sections 1 to 7: Drying overview and strategy, coupe, log yard, green mill, green pack, bioprotection, rack timber.

Australian hardwood drying best practice manual. Part 1

This manual is a guide to establishing a set of operations to achieve high grade results in product quality and recovery, flexibility, innovation, cost, and competitiveness. The manual outlines: - economic and feasible technologies for increasing recovery and reducing avoidable loss during processing, from the log to the finished board, and - mechanisms that allow production value to be optimised in different sized mills. Part 1 covers sections 1 to 7: Drying overview and strategy, coupe, log yard, green mill, green pack, bioprotection, rack timber. Part 2 Link: http://era.deedi.qld.gov.au/3137 Includes sections 8 to 17: Air drying, pre-drying, reconditioning, controlled final drying, dry milling, storage, information assessment, drying quality assessment, moisture content monitoring, glossary.

Moisture variation in dried hardwood timber.

The objectives of this project were to: 1. Understand why moisture gradients occur in Australian hardwoods during drying and their affects on the performance of timber in service; 2. Improve existing technology(ies) and/or processes to reduce moisture content (MC) variability between and within boards during drying of Australian hardwoods in an economical and practical manner.

The structure of Norway spruce (Picea abies [L.] Karst.) stems in relation to wood properties of sawn timber

An important challenge in forest industry is to get the appropriate raw material out from the forests to the wood processing industry. Growth and stem reconstruction simulators are therefore increasingly integrated in industrial conversion simulators, for linking the properties of wooden products to the three-dimensional structure of stems and their growing conditions. Static simulators predict the wood properties from stem dimensions at the end of a growth simulation period, whereas in dynamic approaches, the structural components, e.g. branches, are incremented along with the growth processes. The dynamic approach can be applied to stem reconstruction by predicting the three-dimensional stem structure from external tree variables (i.e. age, height) as a result of growth to the current state. In this study, a dynamic growth simulator, PipeQual, and a stem reconstruction simulator, RetroSTEM, are adapted to Norway spruce (Picea abies [L.] Karst.) to predict the three-dimensional structure of stems (tapers, branchiness, wood basic density) over time such that both simulators can be integrated in a sawing simulator. The parameterisation of the PipeQual and RetroSTEM simulators for Norway spruce relied on the theoretically based description of tree structure developing in the growth process and following certain conservative structural regularities while allowing for plasticity in the crown development. The crown expressed both regularity and plasticity in its development, as the vertical foliage density peaked regularly at about 5 m from the stem apex, varying below that with tree age and dominance position (Study I). Conservative stem structure was characterized in terms of (1) the pipe ratios between foliage mass and branch and stem cross-sectional areas at crown base, (2) the allometric relationship between foliage mass and crown length, (3) mean branch length relative to crown length and (4) form coefficients in branches and stem (Study II). The pipe ratio between branch and stem cross-sectional area at crown base, and mean branch length relative to the crown length may differ in trees before and after canopy closure, but the variation should be further analysed in stands of different ages and densities with varying site fertilities and climates. The predictions of the PipeQual and RetroSTEM simulators were evaluated by comparing the simulated values to measured ones (Study III, IV). Both simulators predicted stem taper and branch diameter at the individual tree level with a small bias. RetroSTEM predictions of wood density were accurate. For focusing on even more accurate predictions of stem diameters and branchiness along the stem, both simulators should be further improved by revising the following aspects in the simulators: the relationship between foliage and stem sapwood area in the upper stem, the error source in branch sizes, the crown base development and the height growth models in RetroSTEM. In Study V, the RetroSTEM simulator was integrated in the InnoSIM sawing simulator, and according to the pilot simulations, this turned out to be an efficient tool for readily producing stand scale information about stem sizes and structure when approximating the available assortments of wood products.

Management of multi-scale forest resource data over time

During the last decades there has been a global shift in forest management from a focus solely on timber management to ecosystem management that endorses all aspects of forest functions: ecological, economic and social. This has resulted in a shift in paradigm from sustained yield to sustained diversity of values, goods and benefits obtained at the same time, introducing new temporal and spatial scales into forest resource management. The purpose of the present dissertation was to develop methods that would enable spatial and temporal scales to be introduced into the storage, processing, access and utilization of forest resource data. The methods developed are based on a conceptual view of a forest as a hierarchically nested collection of objects that can have a dynamically changing set of attributes. The temporal aspect of the methods consists of lifetime management for the objects and their attributes and of a temporal succession linking the objects together. Development of the forest resource data processing method concentrated on the extensibility and configurability of the data content and model calculations, allowing for a diverse set of processing operations to be executed using the same framework. The contribution of this dissertation to the utilisation of multi-scale forest resource data lies in the development of a reference data generation method to support forest inventory methods in approaching single-tree resolution.

Single household domestic water heater design and control utilising PV energy: The untapped energy storage solution

Photovoltaic (PV) panels and electric domestic water heater with storage (DWH) are widely used in households in many countries. However, DWH should be explored as an energy storage mechanism before batteries when households have excess PV energy. Through a residential case study in Queensland, Australia, this paper presents a new optimized design and control solution to reduce water heating costs by utilizing existing DWH energy storage capacity and increasing PV self-consumption for water heating. The solution is produced by evaluating the case study energy profile and numerically maximizing the use of PV for DWH. A conditional probability matrix for different solar insolation and hot water usage days is developed to test the solution. Compared to other tariffs, this solution shows cost reduction from 20.8% to 63.3% This new solution could encourage solar households move to a more economical and carbon neutral water heating method.