Optimization of wastewater quality in the Sines refinery

In order to address and resolve the wastewater contamination problem of the Sines refinery with the main objective of optimizing the quality of this stream and reducing the costs charged to the refinery, a dynamic mass balance was developed nd implemented for ammonia and polar oil and grease (O&G) contamination in the wastewater circuit. The inadequate routing of sour gas from the sour water stripping unit and the kerosene caustic washing unit, were identified respectively as the major source of ammonia and polar substances present in the industrial wastewater effluent. For the O&G content, a predictive model was developed for the kerosene caustic washing unit, following the Projection to Latent Structures (PLS) approach. Comparison between analytical data for ammonia and polar O&G concentrations in refinery wastewater originating from the Dissolved Air Flotation (DAF) effluent and the model predictions of the dynamic mass balance calculations are in a very good agreement and highlights the dominant impact of the identified streams for the wastewater contamination levels. The ammonia contamination problem was solved by rerouting the sour gas through an existing clogged line with ammonia salts due to a non-insulated line section, while for the O&G a dynamic mass balance was implemented as an online tool, which allows for prevision of possible contamination situations and taking the required preventive actions, and can also serve as a basis for establishing relationships between the O&G contamination in the refinery wastewater with the properties of the refined crude oils and the process operating conditions. The PLS model developed could be of great asset in both optimizing the existing and designing new refinery wastewater treatment units or reuse schemes. In order to find a possible treatment solution for the spent caustic problem, an on-site pilot plant experiments for NaOH recovery from the refinery kerosene caustic washing unit effluent using an alkaline-resistant nanofiltration (NF) polymeric membrane were performed in order to evaluate its applicability for treating these highly alkaline and contaminated streams. For a constant operating pressure and temperature and adequate operating conditions, 99.9% of oil and grease rejection and 97.7% of chemical oxygen demand (COD) rejection were observed. No noticeable membrane fouling or flux decrease were registered until a volume concentration factor of 3. These results allow for NF permeate reuse instead of fresh caustic and for significant reduction of the wastewater contamination, which can result in savings of 1.5 M€ per year at the current prices for the largest Portuguese oil refinery. The capital investments needed for implementation of the required NF membrane system are less than 10% of those associated with the traditional wet air oxidation solution of the spent caustic problem. The operating costs are very similar, but can be less than half if reusing the NF concentrate in refinery pH control applications. The payback period was estimated to be 1.1 years. Overall, the pilot plant experimental results obtained and the process economic evaluation data indicate a very competitive solution through the proposed NF treatment process, which represents a highly promising alternative to conventional and existing spent caustic treatment units.

Diseño y caracterización de plataformas de biorreconocimiento basadas en el uso de nanoestructuras, biomoléculas y polímeros. Aplicaciones para el desarrollo de (bio)sensores electroquímicos. Design and characterization of biorecognition platforms based on the use of nanostructures, biomolecules and polymers. Applications for the development of electrochemical (bio)sensors.

Los requerimientos de métodos analíticos que permitan realizar determinaciones más eficientes en diversas ramas de la Química, así como el gran desarrollo logrado por la Nanobiotecnología, impulsaron la investigación de nuevas alternativas de análisis. Hoy, el campo de los Biosensores concita gran atención en el primer mundo, sin embargo, en nuestro país es todavía un área de vacancia, como lo es también la de la Nanotecnología. El objetivo de este proyecto es diseñar y caracterizar nuevos electrodos especialmente basados en el uso de nanoestructuras y estudiar aspectos básicos de la inmovilización de enzimas, ADN, aptámeros, polisacáridos y otros polímeros sobre dichos electrodos a fin de crear nuevas plataformas de biorreconocimiento para la construcción de (bio)sensores electroquímicos dirigidos a la cuantificación de analitos de interés clínico, farmaco-toxicológico y ambiental.Se estudiarán las propiedades de electrodos de C vítreo, Au, "screen printed" y compósitos de C modificados con nanotubos de C (CNT) y/o nanopartículas (NP) de oro y/o nanoalambres empleando diversas estrategias. Se investigarán nuevas alternativas de inmovilización de las biomoléculas antes mencionadas sobre dichos electrodos, se caracterizarán las plataformas resultantes y se evaluarán sus posibles aplicaciones analíticas al desarrollo de biosensores con enzimas y ADNs como elementos de biorreconocimiento. Se funcionalizarán CNT con polímeros comerciales y sintetizados en nuestro laboratorio modificados con moléculas bioactivas. Se diseñarán y caracterizarán nuevas arquitecturas supramoleculares basadas en el autoensamblado de policationes, enzimas y ADNs sobre Au. Se evaluarán las propiedades catalíticas de NP de magnetita y de perovskitas de Mn y su aplicación al desarrollo de biosensores enzimáticos. Se diseñarán biosensores que permitan la detección altamente sensible y selectiva de secuencias específicas de ADNs de interés clínico. Se estudiará la interacción de genotóxicos con ADN (en solución e inmovilizado) y se desarrollarán biosensores que permitan su cuantificación. Se construirán biosensores enzimáticos para la cuantificación de bioanalitos, especialmente glucosa, fenoles y catecoles, y sensores electroquímicos para la determinación de neurotransmisores, ácido úrico y ácido ascórbico. Se diseñarán nuevos aptasensores electroquímicos para la cuantificación de biomarcadores, comenzando por lisozima y trombina y continuando con otros de interés regional/nacional.Se emplearán las siguientes técnicas: voltamperometrías cíclica (CV), de pulso diferencial (DPV) y de onda cuadrada (SWV); "stripping" potenciométrico a corriente constante (PSA); elipsometría; microbalanza de cristal de cuarzo con cálculo de pérdida de energía por disipación (QCM-D); resonancia de plasmón superficial con detección dual (E-SPR); espectroscopía de impedancia electroquímica (EIE); microscopías de barrido electroquímico (SECM), de barrido electrónico (SEM), de transmisión (TEM) y de fuerzas atómicas (AFM); espectrofotometría UV-visible; espectroscopías IR, Raman, de masas, RMN.Se espera que la inclusión de los CNT y/o de las NP metálicas y/o de los nanoalambres en los diferentes electrodos permita una mejor transferencia de carga de diversos analitos y por ende una detección más sensible y selectiva de bioanalitos empleando enzimas, ADN y aptámeros como elementos de biorreconocimiento. Se espera una mayor eficiencia en los aptasensores respecto de los inmunosensores, lo que permitirá la determinacion selectiva de diversos biomarcadores. La modificación de electrodos con nanoestructuras posibilitará la detección altamente sensible y selectiva del evento de hibridación. La respuesta obtenida luego de la interacción de genotóxicos con ADN permitirá un mejor conocimiento de la asociación establecida, de la cinética y de las constantes termodinámicas. Los neurotransmisores podrán ser determinados a niveles nanomolares aún en muestras complejas.

Electroquímica de sustancias de interés en los sistemas agroalimentario y de sanidad animal. Desarrollo de biosensores electroquímicos. Aplicaciones analíticas.Electrochemistry of substances of interest in agroalimentary and animal health systems. Development of electrochemical biosensors. Analytical applications.

Se estudiarán los mecanismos de reacción electroquímica de las micotoxinas (metabolitos tóxicos generados por hongos) citrinina (CIT), patulina (PAT) y moniliformina (MON), de los antioxidantes naturales alfa, beta, gama y delta tocoferoles, de los flavonoides fisetina (FIS), morina (MOR), luteolina (LUT), rutina (RUT), buteina (BUT), naringenina (NAR) y miricetina (MIR) y de las hormonas esteroides estradiol (EDIOL), estrona (EONA) y estriol (ETRIOL). Por otra parte, se implementarán técnicas electroanalíticas para la detección y cuantificación de estos sustratos en muestras de matrices naturales que los contengan. Se realizará el diseño y caracterización de biosensores enzimáticos a partir de peroxidasas y/o fosfatasa alcalina para la determinación de la micotoxina CIT y de los flavonoides y, por otro, de inmunosensores para las micotoxinas ocratoxina A (OTA) y PAT y hormonas. Para el anclaje de enzimas y/o anticuerpos, se estudiarán las propiedades de electrodos modificados por monocapas autoensambladas, nanotubos de carbono y partículas magnéticas. Se usarán las técnicas de voltamperometría cíclica, de onda cuadrada y de redisolución con acumulación adsortiva, espectroscopías de impedancia electroquímica, electrólisis a potencial controlado, uv-vis e IR, microbalanza de cristal de cuarzo y microscopías de alta resolución (SEM, TEM, AFM). La importancia de este proyecto apunta a la obtención de nuevos datos electroquímicos de los sustratos indicados y conocimientos relacionados con la aplicación de electrodos modificados en la preparación de biosensores y en el desarrollo de técnicas alternativas para la determinación de los analitos mencionados precedentemente. Electrochemical reaction mechanisms of mycotoxins (toxic metabolites generated by fungi) citrinin (CIT), Patulin (PAT) and moniliformin (MON), natural antioxidants alpha, beta, gamma and delta tocopherols, flavonoids fisetin (FIS), morin (MOR), luteolin (LUT), rutin (RUT), butein (BUT), naringenin (NAR), miricetin (MIR) and steroid hormones estradiol (EDIOL), estrone (EONA) and estriole (ETRIOL) will be explored. On the other hand, electroanalytical techniques for the detection and quantification of these substrates in samples of natural matrices will be implemented. The design and characterization of enzymatic biosensors from peroxidases and/or from alkaline phosphatase for the determination of CIT and flavonoids, and also of inmunosensors for ochratoxin A (OTA) and PAT and hormones will be performed. For the anchor of enzymes and/or antibody, properties of electrodes modified by self assembled monolayers, carbon nanotubes and magnetic particles will be explored. Cyclic, square wave and adsorptive stripping voltammetries, electrochemical impedance spectroscopy, controlled potential electrolysis, uv-vis and IR, quartz crystal microbalance and high-resolution microcopies (SEM, TEM, AFM) will be used. The importance of this project is aimed at obtaining new electrochemical data for the indicated substrates and knowledge on the application of modified electrodes in preparation of biosensors and in the development of alternative techniques for the determination of the above-mentioned analytes.

Prevención, seguimiento y evaluación de la descontaminación de percloroetileno en suelo y aguas subterráneas en un terreno industrial

La contaminación de suelos y aguas subterráneas es uno de los problemas ambientales más extendidos en gran parte de los terrenos industriales de Cataluña. En este proyecto se ha analizado el proceso de gestión de la contaminación: caracterización, remediación y seguimiento de la descontaminación en suelos y aguas subterráneas por un caso de afección por organoclorados (percloroetileno) y otros contaminantes (hidrocarburos, selenio y cromo) en un emplazamiento industrial situado en una zona agroforestal (superficie de 81.462 m2). A partir de la implantación en la empresa del sistema de gestión ISO 14.001 en 1.996, se abrieron diferentes proyectos de gestión para los posibles contaminantes. Por las mismas fechas, también se detectó una afección por selenio en aguas subterráneas, ajena a la empresa de estudio. Por el momento, el único contaminante que ha requerido de un proceso de descontaminación ha sido el percloroetileno. En suelos se emplea el método “soil vapor extraction” y en aguas subterráneas el método “airstripping”. Finalmente, se ha llevado a cabo una comparación de los costes reales derivados del proceso de descontaminación del percloroetileno en contra de los costes que se hubiesen derivado la implantación de medidas de prevención de la contaminación. El resultado de la valoración indica que la descontaminación de éste compuesto requiere de una inversión económica importante, unas 10 veces más elevada que los costes derivados de las medidas de prevención.

Alternativas tecnológicas para la recuperación y valorización del nitrógeno presente en los residuos orgánicos

La conciencia de los problemas asociados a la gestión de los residuos orgánicos y el interés por las oportunidades de su recuperación y valorización han ido tomando importancia en los últimos años, tanto en el campo de las deyecciones ganaderas como en el sector de las aguas residuales. Consecuentemente, las combinaciones tecnológicas que permitan cerrar los ciclos de los nutrientes y la recuperación energética han adquirido mayor importancia en la investigación así como en las nuevas normativas sectoriales. En este contexto se sitúa el trabajo realizado durante el periodo becado (octubre 2010 - noviembre 2011). En una primera etapa de estudio bibliográfico se identificaron i) el aumento de la eficiencia en el uso del nitrógeno en la agricultura y en la ganadería, ii) la reutilización del nitrógeno en los mismos ecosistemas agrícolas y iii) el tratamiento de las deyecciones para redistribuir el nitrógeno a zonas con poca disponibilidad, como las tres direcciones principales hacia las cuales se está focalizando el interés del sector agrícola. Se puso en marcha una planta piloto de stripping y absorción para estudiar la posibilidad de recuperar y valorizar el amoniaco presente en los purines en forma de solución amoniacal para la industria de fertilizantes. Los resultados obtenidos evidenciaron el rol fundamental de las características iníciales del substrato en el rendimiento global del proceso. En particular, elevados contenidos en materia orgánica resultaron en bajas eficiencias y en elevadas contaminaciones del producto obtenido. Finalmente, considerando sus potenciales ventajas tanto en la gestión de los residuos ganaderos como de las aguas residuales y focalizándose en las perdidas de nitrógeno se estudió un sistema descentralizado de separación de orina instalado en un centro de investigación. Los resultados preliminares permitieron caracterizar los principales procesos que ocurren en el sistema e identificar las posibles líneas futuras de investigación.

Decreased local control following radiation therapy alone in early-stage glottic carcinoma with anterior commissure extension.

PURPOSE: To assess the patterns of failure in the treatment of early-stage squamous cell carcinoma of the glottic larynx. PATIENTS AND METHODS: Between 1983-2000, 122 consecutive patients treated for early laryngeal cancer (UICC T1N0 and T2N0) by radical radiation therapy (RT) were retrospectively studied. Male-to-female ratio was 106 : 16, and median age 62 years (35-92 years). There were 68 patients with T1a, 18 with T1b, and 36 with T2 tumors. Diagnosis was made by biopsy in 104 patients, and by laser vaporization or stripping in 18. Treatment planning consisted of three-dimensional (3-D) conformal RT in 49 (40%) patients including nine patients irradiated using arytenoid protection. A median dose of 70 Gy (60-74 Gy) was given (2 Gy/fraction) over a median period of 46 days (21-79 days). Median follow-up period was 85 months. RESULTS: The 5-year overall, cancer-specific, and disease-free survival amounted to 80%, 94%, and 70%, respectively. 5-year local control was 83%. Median time to local recurrence in 19 patients was 13 months (5-58 months). Salvage treatment consisted of surgery in 17 patients (one patient refused salvage and one was inoperable; total laryngectomy in eleven, and partial laryngectomy or cordectomy in six patients). Six patients died because of laryngeal cancer. Univariate analyses revealed that prognostic factors negatively influencing local control were anterior commissure extension, arytenoid protection, and total RT dose < 66 Gy. Among the factors analyzed, multivariate analysis (Cox model) demonstrated that anterior commissure extension, arytenoid protection, and male gender were the worst independent prognostic factors in terms of local control. CONCLUSION: For early-stage laryngeal cancer, outcome after RT is excellent. In case of anterior commissure extension, surgery or higher RT doses are warranted. Because of a high relapse risk, arytenoid protection should not be attempted.

Warm Front, Better Health: Health Impact Evaluation of the Warm Front Scheme

About 4 million households in the UK cannot adequately heat their homes in winter due to low income and poor quality housing, the two main causes of fuel poverty. The primary impact of fuel poverty is cold homes in winter which can lead to various health problems and even death among the vulnerable young and the elderly population. The government launched the Warm Front scheme in 2000 to tackle fuel poverty among the vulnerable households in England by providing energy efficiency measures in the forms insulation and modern heating system(??). By 2004, about 770,000 households had benefited from the Warm Front scheme and a total of 2 million households are still expected to benefit by 2010. Since 2001, the Bartlett has been investigating with London School of Hygiene & Tropical Medicine and Sheffield Hallam University, the health and the environmental impact of the Warm Front scheme. This investigative study is the most detailed to date on fuel poor dwellings based on detailed surveys of household and dwelling data, fuel consumption record and monitored temperature and relative humidity from 3,100 dwellings before and after the energy efficiency measures. The Warm Front investigation was expected to continue until the end of 2007. The findings from the investigation indicated that the Warm Front scheme was likely to have benefits in terms of improved thermal comfort and well-being as a result of mean temperature rise of 1.6C in the living room and 2.8C in the bedroom. Warm Front also lead to a decrease in indoor relative humidity mainly from the increased temperature since there appeared to be little impact on vapour pressure from changes in air tightness. Pressure test results indicated that the effects of air tightness measures such as draught stripping and cavity wall insulation were offset by the installation of a central heating system, particularly when the pipe work feeding radiators was installed below timber floors.

Catheter entrapment in a pulmonary vein: a unique complication of pulmonary vein isolation.

Ablation strategies for the treatment of atrial fibrillation (AF) are associated with several potential complications. During electro-anatomic mapping of the left atrium (LA) before ablation, the ablation catheter was entrapped in the right inferior pulmonary vein (RIPV). After multiple unsuccessful gentle tractions, stronger maneuvers with rotation of the catheter slowly allowed its retrieval. Examination of the catheter showed a thin, translucent membrane covering its tip, suggesting complete stripping of a vein branch. Occlusion of the superior branch of the RIPV was confirmed by LA angiogram. During the following days, no pericardial effusion was noted, but the patient complained of light chest pain and mild hemoptysis, spontaneously resolving within 48 h. This case shows that catheter entrapment and mechanical disruption of a PV branch can be a rare potential complication of AF ablation. In this case, the outcome was spontaneously favorable and symptoms only included transient mild hemoptysis.

Fat embolism syndrome after combined aesthetic surgery.

Fat embolism syndrome is a rare complication that develops after extended soft tissue disruption by liposuction, in particular if combined with time consuming, multiple procedures. Early signs are non-specific and often not considered, so that diagnosis and correct management may be delayed. We report a case in which liposuction combined with other aesthetic surgical procedures caused a fat embolism syndrome in a 46-year-old woman, which was followed by multiple organ failure and the development of sepsis with perimammary abscesses. Extended liposuction of the abdomen and thighs, bilateral augmentation mammaplasty, and stripping of both greater saphenous veins were combined.

Evalution of Hot Mix Asphalt Moisture Sensitivity Using the Nottingham Asphalt Test Equipment, July 2005

Moisture sensitivity of Hot Mix Asphalt (HMA) mixtures, generally called stripping, is a major form of distress in asphalt concrete pavement. It is characterized by the loss of adhesive bond between the asphalt binder and the aggregate (a failure of the bonding of the binder to the aggregate) or by a softening of the cohesive bonds within the asphalt binder (a failure within the binder itself), both of which are due to the action of loading under traffic in the presence of moisture. The evaluation of HMA moisture sensitivity has been divided into two categories: visual inspection test and mechanical test. However, most of them have been developed in pre-Superpave mix design. This research was undertaken to develop a protocol for evaluating the moisture sensitivity potential of HMA mixtures using the Nottingham Asphalt Tester (NAT). The mechanisms of HMA moisture sensitivity were reviewed and the test protocols using the NAT were developed. Different types of blends as moisture-sensitive groups and non-moisture-sensitive groups were used to evaluate the potential of the proposed test. The test results were analyzed with three parameters based on performance character: the retained flow number depending on critical permanent deformation failure (RFNP), the retained flow number depending on cohesion failure (RFNC), and energy ratio (ER). Analysis based on energy ratio of elastic strain (EREE ) at flow number of cohesion failure (FNC) has higher potential to evaluate the HMA moisture sensitivity than other parameters. If the measurement error in data-acquisition process is removed, analyses based on RFNP and RFNC would also have high potential to evaluate the HMA moisture sensitivity. The vacuum pressure saturation used in AASHTO T 283 and proposed test has a risk to damage specimen before the load applying.

Peroxisome-proliferator-activated receptor (PPAR)-gamma activation stimulates keratinocyte differentiation.

Previous studies demonstrated that peroxisome-proliferator-activated receptor (PPAR)-alpha or PPAR-delta activation stimulates keratinocyte differentiation, is anti-inflammatory, and improves barrier homeostasis. Here we demonstrate that treatment of cultured human keratinocytes with ciglitazone, a PPAR-gamma activator, increases involucrin and transglutaminase 1 mRNA levels. Moreover, topical treatment of hairless mice with ciglitazone or troglitazone increases loricrin, involucrin, and filaggrin expression without altering epidermal morphology. These results indicate that PPAR-gamma activation stimulates keratinocyte differentiation. Additionally, PPAR-gamma activators accelerated barrier recovery following acute disruption by either tape stripping or acetone treatment, indicating an improvement in permeability barrier homeostasis. Treatment with PPAR-gamma activators also reduced the cutaneous inflammatory response that is induced by phorbol 12-myristate-13-acetate, a model of irritant contact dermatitis and oxazolone, a model of allergic contact dermatitis. To determine whether the effects of PPAR-gamma activators are mediated by PPAR-gamma, we next examined animals deficient in PPAR-gamma. Mice with a deficiency of PPAR-gamma specifically localized to the epidermis did not display any cutaneous abnormalites on inspection, but on light microscopy there was a modest increase in epidermal thickness associated with an increase in proliferating cell nuclear antigen (PCNA) staining. Key functions of the skin including permeability barrier homeostasis, stratum corneum surface pH, and water-holding capacity, and response to inflammatory stimuli were not altered in PPAR-gamma-deficient epidermis. Although PPAR-gamma activators stimulated loricrin and filaggrin expression in wild-type animals, however, in PPAR-gamma-deficient mice no effect was observed indicating that the stimulation of differentiation by PPAR-gamma activators is mediated by PPAR-gamma. In contrast, PPAR-gamma activators inhibited inflammation in both PPAR-gamma-deficient and wild-type mouse skin, indicating that the inhibition of cutaneous inflammation by these PPAR-gamma activators does not require PPAR-gamma in keratinocytes. These observations suggest that thiazolidindiones and perhaps other PPAR-gamma activators maybe useful in the treatment of cutaneous disorders.

Activin a inhibits antigen-induced allergy in murine epicutaneous sensitization.

Activin A, a member of the TGFβ superfamily, is involved in physiological processes such as cell differentiation, tissue homeostasis, wound healing, reproduction, and in pathological conditions, such as fibrosis, cancer, and asthma. Activin enhances mast cell maturation, as well as regulatory T-cell and Langerhans cell differentiation. In this study we investigated the potential role of activin in epicutaneous sensitization with ovalbumin (OVA), notably with respect to its effect on known Th2-polarization. For this purpose, transgenic mice overexpressing activin in keratinocytes and their wild-type (WT) controls were sensitized epicutaneously with OVA. Skin biopsies were analyzed with regard to histopathological features and mRNA expression of pro-inflammatory and Th1/Th2 cytokines, and Ig levels were measured in the serum. Unexpectedly, activin overexpressing animals were protected from Th2-cytokine expression and induction of OVA-specific IgE levels compared to WT animals. On the other hand, transgenic mice were more susceptible to inflammation compared to WT littermates after tape-stripping and saline (vehicle) or OVA application, as shown by increased pro-inflammatory cytokine mRNA levels and neutrophil accumulation at the site of the treatment. We conclude that activin protects from antigen-induced cutaneous Th2-polarization through modulation of the immune response. These findings highlight the role of activin in cutaneous sensitization, allergy, and in skin homeostasis.

Obtenció d'estruvita a partir de la fracció líquida digerida de purins de vaca

Actualment a Catalunya existeixen zones amb importants limitacions per l’aplicació de purins al sòl, pel que és imprescindible trobar alternatives de gestió i tractament que permetin l’aprofitament adequat dels recursos continguts a les dejeccions ramaderes sense afectar el medi. La digestió anaeròbia és una de les tècniques utilitzades en el tractament de les dejeccions ramaderes. L’efluent líquid que s’obté d’aquest tractament no modifica el contingut de nitrogen i fòsfor i per tant ha de ser gestionat correctament. L’objectiu general d’aquest projecte és avaluar la precipitació d’estruvita (sal de magnesi, amoni i fosfat) com una alternativa de gestió de l’efluent líquid d’una planta de digestió anaeròbia i compostatge que tracta dejeccions ramaderes conjuntament amb altres residus orgànics. S’han avaluat els efectes dels diferents paràmetres operacionals en la formació d’estruvita (pH, temperatura, velocitat d’agitació, alcalinitat), mitjançant assaigs en discontinu amb solució sintètica. A continuació s’ha procedit a obtenir estruvita a partir de la fracció líquida digerida de purí (FLD), en assaigs en discontinu per estudiar l’efecte del contingut de matèria orgànica i sòlids Totals (ST), així com el contingut en fosfats i el pH de reacció. Finalment, s’han optimitzat els paràmetres de procés en continu, mitjançant la posada en marxa d’un reactor a escala de laboratori i estudi de l’efecte de la velocitat d’agitació i de la introducció del stripping de CO2, tant amb solució sintètica com amb la fracció líquida digerida del purí. Dels resultats obtinguts es pot concloure que els factors que tenen una major influència en el procés d’obtenció d’estruvita són el pH (el pH òptim es situa al voltant de 9), i la presència de matèria orgànica i sòlids ens suspensió, que interfereix de forma quantitativa i qualitativa en la formació de l’estruvita. En el procés en continu s’ha aconseguit reduccions d’un 84% i 98% d’amoni i fòsfor respectivament, obtenintse estruvita que pot ser utilitzada com a fertilitzant d’alliberació lenta. Es pot concloure que la precipitació d’estruvita és una bona alternativa per millorar la gestió de les dejeccions ramaderes alhora que permet recuperar nutrients i tancar cicles. La combinació amb un tractament previ que elimini la matèria orgànica, com podria ser la digestió anaeròbia, i una separació de fases, per eliminar els sòlids en suspensió, es presenta com una configuració amb molts avantatges.

Evaluation of Hot Mix Asphalt Moisture Sensitivity Using the Nottingham Asphalt Test Equipment, July 2005

Moisture sensitivity of Hot Mix Asphalt (HMA) mixtures, generally called stripping, is a major form of distress in asphalt concrete pavement. It is characterized by the loss of adhesive bond between the asphalt binder and the aggregate (a failure of the bonding of the binder to the aggregate) or by a softening of the cohesive bonds within the asphalt binder (a failure within the binder itself), both of which are due to the action of loading under traffic in the presence of moisture. The evaluation of HMA moisture sensitivity has been divided into two categories: visual inspection test and mechanical test. However, most of them have been developed in pre-Superpave mix design. This research was undertaken to develop a protocol for evaluating the moisture sensitivity potential of HMA mixtures using the Nottingham Asphalt Tester (NAT). The mechanisms of HMA moisture sensitivity were reviewed and the test protocols using the NAT were developed. Different types of blends as moisture-sensitive groups and non-moisture-sensitive groups were used to evaluate the potential of the proposed test. The test results were analyzed with three parameters based on performance character: the retained flow number depending on critical permanent deformation failure (RFNP), the retained flow number depending on cohesion failure (RFNC), and energy ratio (ER). Analysis based on energy ratio of elastic strain (EREE ) at flow number of cohesion failure (FNC) has higher potential to evaluate the HMA moisture sensitivity than other parameters. If the measurement error in data-acquisition process is removed, analyses based on RFNP and RFNC would also have high potential to evaluate the HMA moisture sensitivity. The vacuum pressure saturation used in AASHTO T 283 and proposed test has a risk to damage specimen before the load applying.

Ranking of HMA Moisture Sensitivity Tests in Iowa, RB00-012, 2012

Several agencies specify AASHTO T283 as the primary test for field acceptance of moisture susceptibility in hot mix asphalt. When used in this application, logistical difficulties challenge its practicality, while repeatability is routinely scrutinized by contractors. An alternative test is needed which can effectively demonstrate the ability to screen mixtures based on expected performance. The ideal replacement can be validated with field performance, is repeatable, and allows for prompt reporting of results. Dynamic modulus, flow number, AASHTO T283, Hamburg wheel tracking device (HWTD), and the moisture induced sensitivity test (MIST) were performed on plant produced surface mixes in Iowa. Follow-up distress surveys were used to rank the mixes by their performance. The rankings indicate both the quantity of swelling from MIST conditioning and submersed flow number matched the performance ranking of all but one mixture. Hamburg testing parameters also appear effective, namely the stripping inflection point and the ratio between stripping slope and the creep slope. Dynamic modulus testing was ineffective, followed by AASHTO T283 and ratios produced from flow number results of conditioned samples.