Seed survival in Chilean Nothofagus in response to desiccation and storage

Nothofagus alpina, N. obliqua, N. glauca, N. leonii, N. dombeyi and N. pumilio seeds exhibited consistent, albeit slight, sensitivity to extreme desiccation, but nevertheless maintained viability at low moisture contents and cool temperatures (-10 degrees to -20 degrees C) over 2 years. Nothofagus alpina, N. obliqua, N. glauca, N. leonii and N. dombeyi conformed to the seed viability equation of Ellis and Roberts; sensitivity of longevity to temperature was quantitatively similar to that of crop seeds, sensitivity to moisture was somewhat less, and a low-moisture-content limit to the equation was detected at 4.8% moisture content in hermetic storage at 65 degrees C, and possibly similar moisture contents at 30-40 degrees C. These five species show orthodox seed storage behaviour. Therefore, ex-situ conservation of these Nothofagus species in seed banks is possible, but the quality of seed lots collected requires attention. Seed storage behaviour was not defined in N. pumilio: initial seed quality was poor and loss of viability was detected over 2 years at 0 degrees, -10 degrees and -20 degrees C at 2.7% moisture content, but not at 5.2%. The results confirm that the economy of nature in seed storage physiology extends to forest tree seeds, but the repeated observation of reduced sensitivity of longevity to moisture in forest tree seeds requires further investigation.

Evolution in software systems: foundations of the SPE classification scheme

The SPE taxonomy of evolving software systems, first proposed by Lehman in 1980, is re-examined in this work. The primary concepts of software evolution are related to generic theories of evolution, particularly Dawkins' concept of a replicator, to the hermeneutic tradition in philosophy and to Kuhn's concept of paradigm. These concepts provide the foundations that are needed for understanding the phenomenon of software evolution and for refining the definitions of the SPE categories. In particular, this work argues that a software system should be defined as of type P if its controlling stakeholders have made a strategic decision that the system must comply with a single paradigm in its representation of domain knowledge. The proposed refinement of SPE is expected to provide a more productive basis for developing testable hypotheses and models about possible differences in the evolution of E- and P-type systems than is provided by the original scheme. Copyright (C) 2005 John Wiley & Sons, Ltd.

Integrating the Climate Science Modelling Language with geospatial software and services

Much consideration is rightly given to the design of metadata models to describe data. At the other end of the data-delivery spectrum much thought has also been given to the design of geospatial delivery interfaces such as the Open Geospatial Consortium standards, Web Coverage Service (WCS), Web Map Server and Web Feature Service (WFS). Our recent experience with the Climate Science Modelling Language shows that an implementation gap exists where many challenges remain unsolved. To bridge this gap requires transposing information and data from one world view of geospatial climate data to another. Some of the issues include: the loss of information in mapping to a common information model, the need to create ‘views’ onto file-based storage, and the need to map onto an appropriate delivery interface (as with the choice between WFS and WCS for feature types with coverage-valued properties). Here we summarise the approaches we have taken in facing up to these problems.

FACSGen 2.0 animation software: generating three-dimensional FACS-valid facial expressions for emotion research

In this article, we present FACSGen 2.0, new animation software for creating static and dynamic threedimensional facial expressions on the basis of the Facial Action Coding System (FACS). FACSGen permits total control over the action units (AUs), which can be animated at all levels of intensity and applied alone or in combination to an infinite number of faces. In two studies, we tested the validity of the software for the AU appearance defined in the FACS manual and the conveyed emotionality of FACSGen expressions. In Experiment 1, four FACS-certified coders evaluated the complete set of 35 single AUs and 54 AU combinations for AU presence or absence, appearance quality, intensity, and asymmetry. In Experiment 2, lay participants performed a recognition task on emotional expressions created with FACSGen software and rated the similarity of expressions displayed by human and FACSGen faces. Results showed good to excellent classification levels for all AUs by the four FACS coders, suggesting that the AUs are valid exemplars of FACS specifications. Lay participants’ recognition rates for nine emotions were high, and comparisons of human and FACSGen expressions were very similar. The findings demonstrate the effectiveness of the software in producing reliable and emotionally valid expressions, and suggest its application in numerous scientific areas, including perception, emotion, and clinical and euroscience research.

KPIs and their properties defined with the EXTREME method

Key Performance Indicators (KPIs) are the main instruments of Business Performance Management. KPIs are the measures that are translated to both the strategy and the business process. These measures are often designed for an industry sector with the assumptions about business processes in organizations. However, the assumptions can be too incomplete to guarantee the required properties of KPIs. This raises the need to validate the properties of KPIs prior to their application to performance measurement. This paper applies the method called EXecutable Requirements Engineering Management and Evolution (EXTREME) for validation of the KPI definitions. EXTREME semantically relates the goal modeling, conceptual modeling and protocol modeling techniques into one methodology. The synchronous composition built into protocol modeling enables raceability of goals in protocol models and constructive definitions of a KPI. The application of the method clarifies the meaning of KPI properties and procedures of their assessment and validation.

Evaluation of Postpolymerization as a Function of the Storage Time of Triethylene Glycol Dimethacrylate/2,2-Bis[4-(2-Hydroxy-3-Methacryloxy-Prop-1-Oxy)-Phenyl]-propane Bisphenyl-alpha-Glycidyl Ether Dimethacrylate Copolymers Used in Dental Resins by Differential Scanning Calorimetry and Dynamic Mechanical Analysis

The aim of this work was to evaluate the effect of the storage time on the thermal properties of triethylene glycol dimethacrylate/2,2-bis[4-(2-hydroxy-3-methacryloxy-prop-1-oxy)-phenyl]propane bisphenyl-alpha-glycidyl ether dimethacrylate (TB) copolymers used in formulations of dental resins after photopolymerization. The TB copolymers were prepared by photopolymerization with an Ultrablue IS light-emitting diode, stored in the dark for 160 days at 37 degrees C, and characterized with differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and Fourier transform infrared spectroscopy with attenuated total reflection. DSC curves indicated the presence of an exothermic peak, confirming that the reaction was not completed during the photopolymerization process. This exothermic peak became smaller as a function of the storage time and was shifted at higher temperatures. In DMA studies, a plot of the loss tangent versus the temperature initially showed the presence of two well-defined peaks. The presence of both peaks confirmed the presence of residual monomers that were not converted during the photopolymerization process. (C) 2009 Wiley Periodicals, Inc. J Appl Polym Sci 112: 679-684, 2009

Simulation of Sawmill Yard Operations Using Software Agents

Bergkvist insjön AB is a sawmill yard which is capable of producing 350,000 cubic meter of timber every year this requires lot of internal resources. Sawmill operations can be classified as unloading, sorting, storage and production of timber. In the company we have trucks arriving at random they have to be unloaded and sent back at the earliest to avoid queuing up of trucks creating a problem for truck owners. The sawmill yard has to operate with two log stackers that does several tasks including transporting the logs from trucks to measurement station where the logs will be sorted into classes and dropped into pockets from pockets to the sorted timber yard where they are stored and finally from there to sawmill for final processing. The main issue that needs to be answered here is the lining up trucks that are waiting to be unload, creating a problem for both sawmill as well as the truck owners and given huge production volume, it is certain that handling of resources is top priority. A key challenge in handling of resources would be unloading of trucks and finding a way to optimize internal resources.To address this problem i have experimented on different ways of using internal resources, i have designed different cases, in case 1 we have both the log stackers working on sawmill and measurement station. The main objective of having this case is to make sawmill and measurement station to work all the time. Then in case 2, i have divided the work between both the log stackers, one log stacker will be working on sawmill and pocket_control and second log stacker will be working on measurement station and truck. Then in case 3 we have only one log stacker working on all the agents, this case was designed to reduce cost of production, as the experiment cannot be done in real-time due to operational cost, for this purpose simulation is used, preliminary investigation into simulation results suggested that case 2 is the best option has it reduced waiting time of trucks considerably when compared with other cases and it showed 50% increase in optimizing internal resources.

Energy Storage for a Grid-Connected PV-System: A Feasibility Study

The work presented in this thesis concerns the dimensioning of an Energy Storage System (ESS) which will be used as an energy buffer for a grid-connected PV plant. This ESS should help managing the PV plant to inject electricity into the grid according to the requirements of the grid System Operator. It is desired to obtain a final production not below 1300kWh/kWp with a maximum ESS budget of 0.9€/Wp. The PV plant will be sited in Martinique Island and connected to the main grid. This grid is a small one where the perturbations due clouds in the PV generation are not negligible anymore. A software simulation tool, incorporating a model for the PV-plant production, the ESS and the required injection pattern of electricity into the grid has been developed in MS Excel. This tool has been used to optimize the relevant parameters defining the ESS so that the feed-in of electricity into the grid can be controlled to fulfill the conditions given by the System Operator. The inputs used for this simulation tool are, besides the conditions given by the System Operator on the allowed injection pattern, the production data from a similar PV-plant in a close-by location, and variables for defining the ESS. The PV production data used is from a site with similar climate and weather conditions as for the site on the Martinique Island and hence gives information on the short term insolation variations as well as expected annual electricity production. The ESS capacity and the injected electric energy will be the main figures to compare while doing an economic study of the whole plant. Hence, the Net Present Value, Benefit to Cost method and Pay-back period studies are carried on as dependent of the ESS capacity. The conclusion of this work is that it is possible to obtain the requested injection pattern by using an ESS. The design of the ESS can be made within an acceptable budget. The capacity of ESS to link with the PV system depends on the priorities of the final output characteristics, and it also depends on which economic parameter that is chosen as a priority.

Influence of hydraulics and control of thermal storage in solar assisted heat pump combisystems

This paper studies the influence of hydraulics and control of thermal storage in systems combined with solar thermal and heat pump for the production of warm water and space heating in dwellings. A reference air source heat pump system with flat plate collectors connected to a combistore was defined and modeled together with the IEA SHC Task 44 / HPP Annex 38 (T44A38) “Solar and Heat Pump Systems” boundary conditions of Strasbourg climate and SFH45 building. Three and four pipe connections as well as use of internal and external heat exchangers for DHW preparation were investigated as well as sensor height for charging of the DHW zone in the store. The temperature in this zone was varied to ensure the same DHW comfort was achieved in all cases. The results show that the four pipe connection results in 9% improvement in SPF compared to three pipe and that the external heat exchanger for DHW preparation leads to a 2% improvement compared to the reference case. Additionally the sensor height for charging the DHW zone of the store should not be too low, otherwise system performance is adversely affected

Hydrodynamic Simulations Of Vacuum-Driven Storage Tanks

As a result of urbanization, stormwater runoff flow rates and volumes are significantly increased due to increasing impervious land cover and the decreased availability of depression storage. Storage tanks are the basic devices to efficiently control the flow rate in drainage systems during wet weather. Presented in the paper conception of vacuum-driven detention tanks allows to increase the storage capacity by usage of space above the free surface water elevation at the inlet channel. Partial vacuum storage makes possible to gain cost savings by reduction of both the horizontal area of the detention tank and necessary depth of foundations. Simulation model of vacuum-driven storage tank has been developed to estimate potential profits of its application in urban drainage system. Although SWMM5 has no direct options for vacuum tanks an existing functions (i.e. control rules) have been used to reflect its operation phases. Rainfall data used in simulations were recorded at raingage in Czestochowa during years 2010÷2012 with time interval of 10minutes. Simulation results gives overview to practical operation and maintenance cost (energy demand) of vacuum driven storage tanks depending of the ratio: vacuum-driven volume to total storage capacity. The following conclusion can be drawn from this investigations: vacuum-driven storage tanks are characterized by uncomplicated construction and control systems, thus can be applied in newly developed as well as in the existing urban drainage systems. the application of vacuum in underground detention facilities makes possible to increase of the storage capacity of existing reservoirs by usage the space above the maximum depth. Possible increase of storage capacity can achieve even a few dozen percent at relatively low investment costs. vacuum driven storage tanks can be included in existing simulation software (i.e. SWMM) using options intended for pumping stations (including control and action rules ).

Construção de um ambiente de desenvolvimento de software baseado em um sistema de gerência de workflow e outros produtos comerciais

Este trabalho apresenta uma arquitetura para Ambientes de Desenvolvimento de Software (ADS). Esta arquitetura é baseada em produtos comerciais de prateleira (COTS), principalmente em um Sistema de Gerência de Workflow – SGW (Microsoft Exchange 2000 Server – E2K) - e tem como plataforma de funcionamento a Internet, integrando também algumas ferramentas que fazem parte do grande conjunto de aplicativos que é utilizado no processo de desenvolvimento de software. O desenvolvimento de um protótipo (WOSDIE – WOrkflow-based Software Development Integrated Environment) baseado na arquitetura apresentada é descrito em detalhes, mostrando as etapas de construção, funções implementadas e dispositivos necessários para a integração de um SGW, ferramentas de desenvolvimento, banco de dados (WSS – Web Storage System) e outros, para a construção de um ADS. O processo de software aplicado no WOSDIE foi extraído do RUP (Rational Unified Process – Processo Unificado Rational). Este processo foi modelado na ferramenta Workflow Designer, que permite a modelagem dos processos de workflow dentro do E2K. A ativação de ferramentas a partir de um navegador Web e o armazenamento dos artefatos produzidos em um projeto de software também são abordados. O E2K faz o monitoramento dos eventos que ocorrem dentro do ambiente WOSDIE, definindo, a partir das condições modeladas no Workflow Designer, quais atividades devem ser iniciadas após o término de alguma atividade anterior e quem é o responsável pela execução destas novas atividades (assinalamento de atividades). A arquitetura proposta e o protótipo WOSDIE são avaliados segundo alguns critérios retirados de vários trabalhos. Estas avaliações mostram em mais detalhes as características da arquitetura proposta e proporcionam uma descrição das vantagens e problemas associados ao WOSDIE.

Avaliação de desempenho na gestão dos recursos materiais : proposta de um sistema baseado em indicadores numericos e de um software correspondente para uso em microcomputadores

Este trabalho, apresentado sob forma de dissertação, apesar de limitado .ao universo da gestão dos recursos materiais - GRM, representa uma tentativa para a criação de meios para medir a eficiência e a eficácia da função gerencial. Foram contemplados dois segmentos do universo da GRM: as relações comerciais com os fornecedores e as atividades de gerenciamento interno das diversas funções técnico-administrativas. Nestas, atingimos um amplo espectro, indo desde a infra-estrutura gerencial até os respectivos custos operacionais. Foram consideradas as seguintes funções: • Planejamento e Controle • Aquisição de Material • Controle e Distribuição de Material • Qualidade e Desenvolvimento o desempenho de cada uma das funções é avaliado por meio de indicadores, resultantes da combinação de dados operacionais, tais como: produção, venda, número de empregados envolvidos, valor das aquisições realizadas, custos de aquisição e de estocagem, valor dos estoques, carga transportada, custos de controle de qualidade e outros relacionados à GRM de uma organização. Consideramos que três orientações deste tabalho apresentam certo grau de originalidade. A primeira refere-se ao ajustamento dos valores monetários envolvidos, a fim de adequá-los às características inflacionárias da nossa economia. A segunda é o tratamento estatístico dos dados para que sejam reduzidas eventuais distorções. Assim, teremos indicadores próximos da realidade, baseados em números correntes e expurgados de variações aleatórias. A terceira orientação é o uso da informática para proporcionar a maior disseminação possível dos indicadores, seja na entrada de dados, no ajustamento, no cálculo, na armazenagem, na recuperação, no tratamento estatístico e na análise e criação de padrões de desempenho gerencial. Como anexo à dissertação, estamos incluindo disquetes em 3 1/2" e 5 1/4", contendo software interativo, denominado SIGMAT - Sistema de Indicadores para a Avaliação do Desempenho da Gestão dos Recursos Materiais. Este aplicativo executa todas as propostas apresentadas na presente dissertação.

Activity modeling in practice: a case-based guide to human-centered software engineering

The purpose of this study was to identify whether activity modeling framework supports problem analysis and provides a traceable and tangible connection from the problem identification up to solution modeling. Methodology validation relied on a real problem from a Portuguese teaching syndicate (ASPE), regarding courses development and management. The study was carried out with a perspective to elaborate a complete tutorial of how to apply activity modeling framework to a real world problem. Within each step of activity modeling, we provided a summary elucidation of the relevant elements required to perform it, pointed out some improvements and applied it to ASPE’s real problem. It was found that activity modeling potentiates well structured problem analysis as well as provides a guiding thread between problem and solution modeling. It was concluded that activity-based task modeling is key to shorten the gap between problem and solution. The results revealed that the solution obtained using activity modeling framework solved the core concerns of our customer and allowed them to enhance the quality of their courses development and management. The principal conclusion was that activity modeling is a properly defined methodology that supports software engineers in problem analysis, keeping a traceable guide among problem and solution.

Design gráfico da pluma de contaminação por compostos orgânicos voláteiss utilizando software CAD na investigação de passivo ambiental em um posto revendedor de combustíveis em Natal/RN

Among the potentially polluting economic activities that compromise the quality of groundwater are the gas stations. The city of Natal has about 120 gas stations, of which only has an environmental license for operation. Discontinuities in the offices were notified by the Public Ministry of Rio Grande do Norte to carry out the environmental adaptations, among which is the investigation of environmental liabilities. The preliminary and confirmatory stages of this investigation consisted in the evaluation of soil gas surveys with two confirmatory chemical analysis of BTEX, PAH and TPH. To get a good evaluation and interpretation of results obtained in the field, it became necessary three-dimensional representation of them. We used a CAD software to graph the equipment installed in a retail service station fuel in Natal, as well as the plumes of contamination by volatile organic compounds. The tool was concluded that contamination is not located in the current system of underground storage of fuel development, but reflects the historical past in which tanks were removed not tight gasoline and diesel

Uma abordagem sistemática para implementação, gerenciamento e customização de testes de linhas de produto de software

Through the adoption of the software product line (SPL) approach, several benefits are achieved when compared to the conventional development processes that are based on creating a single software system at a time. The process of developing a SPL differs from traditional software construction, since it has two essential phases: the domain engineering - when common and variables elements of the SPL are defined and implemented; and the application engineering - when one or more applications (specific products) are derived from the reuse of artifacts created in the domain engineering. The test activity is also fundamental and aims to detect defects in the artifacts produced in SPL development. However, the characteristics of an SPL bring new challenges to this activity that must be considered. Several approaches have been recently proposed for the testing process of product lines, but they have been shown limited and have only provided general guidelines. In addition, there is also a lack of tools to support the variability management and customization of automated case tests for SPLs. In this context, this dissertation has the goal of proposing a systematic approach to software product line testing. The approach offers: (i) automated SPL test strategies to be applied in the domain and application engineering, (ii) explicit guidelines to support the implementation and reuse of automated test cases at the unit, integration and system levels in domain and application engineering; and (iii) tooling support for automating the variability management and customization of test cases. The approach is evaluated through its application in a software product line for web systems. The results of this work have shown that the proposed approach can help the developers to deal with the challenges imposed by the characteristics of SPLs during the testing process