Correlating The Features Of Topography To Friction By Sliding Experiments

Friction can influence the quality of the finished product to a large extent in certain manufacturing processes. Sheet metal forming is a particular case, where the friction between the hard-die and the relatively soft work-piece can be extremely important. Under such conditions, topography of the harder surface can influence the resistance to traction at the interface. This paper discusses about the correlation between certain features of the surface; topography and coefficient of friction based on experiments involving sliding of a few soft metal pins against a harder material. A brief description of the experimental procedure and the analysis are presented. A hybrid parameter which encapsulates both the amplitude features as well as the relative packing of peaks is shown to correlate well with the coefficient of friction.

Caracterização experimental e modelação numérica de espumas metálicas

As espumas de alumínio são materiais ultraleves, o que as torna atractivas para um largo espectro de aplicações comerciais na área da defesa, na indústria automóvel e aeroespacial, entre outras. Actualmente, há um grande interesse na utilização de espumas de alumínio em componentes estruturais ultraleves, incorporados em sistemas de absorção de energia para protecção contra o impacto. O recurso à simulação numérica para resolver problemas de engenharia em várias áreas é cada vez mais comum. A modelação numérica dos materiais assume vital importância quando o problema envolve a análise de processos tecnológicos como, por exemplo, a conformação plástica de materiais, ou a análise de estruturas. Deste modo, torna-se imprescindível garantir que a modelação dos materiais é de tal forma rigorosa que permite simular o melhor possível o seu comportamento real nas condições concretas da análise a realizar. A forma mais comum de garantir o rigor dos modelos utilizados é a validação dos modelos numéricos tendo por base resultados experimentais. Neste trabalho, fez-se a caracterização do comportamento mecânico das espumas de alumínio com nome comercial ALPORAS!, obtidas pelo processo de fabrico denominado expansão directa do metal fundido por adição de um agente expansor. Esta caracterização consistiu num conjunto de ensaios experimentais quer no regime quasi-estático, quer no regime dinâmico. No regime quasi-estático realizaram-se ensaios de compressão uniaxial e de compressão multiaxial. Para a caracterização no regime dinâmico foram realizados ensaios em barras de Hopkinson de polimetil-metacrilato (PMMA). Com base nos resultados experimentais obtidos determinaram-se os parâmetros dos dois modelos constitutivos para espumas metálicas implementados no programa comercial Abaqus™/Explicit. Estes modelos, e os respectivos parâmetros determinados, foram validados reproduzindo numericamente alguns ensaios experimentais quasi-estáticos e dinâmicos. Assim, verificou-se a adequabilidade dos modelos em diversas condições quer em termos de esforços quer em termos de regime de taxa de deformação Por último, desenvolveu-se uma estrutura inovadora para absorção de energia durante um impacto, constituída por componentes perfilados em liga de alumínio e por componentes em espumas de alumínio. Esta estrutura foi testada exclusivamente com recurso à simulação numérica, utilizando os modelos constitutivos validados anteriormente.

Estudo de Ferramentas FEA Comerciais na Simulação Numérica de Processos de Conformação de Chapas Metálicas. Aplicação à Indústria Automóvel.

Os componentes obtidos através da conformação plástica de chapas têm uma grande importância, tanto na etapa de concepção do produto como na etapa de produção na indústria automóvel. Isto comprova-se pelo facto de, em média, cada automóvel integrar cerca de 500 componentes estampados para construir o chassis e a carroçaria [Alves 2003]. Deste total de componentes, 50 são de grandes dimensões (portas, tejadilho, painéis inferior e laterais, entre outros) e necessitam, em média, de cinco ferramentas para o seu fabrico, sendo o custo estimado para cada ferramenta de 230 000 € [Col 2000, Alves 2003]. Para além da indústria automóvel, a conformação plástica de chapas metálicas é um processo tecnológico presente nas indústrias relativas à aeroespacial, petrolífera, decoração, alimentar, entre outras. Do ponto de vista do enquadramento económico, cerca de 20% do custo total de um automóvel novo é devido à incorporação de componentes metálicos estampados. [Alves 2003]. A pressão do “Mercado Global” faz com que os custos relativos à matéria-prima, energia e mão-de-obra sejam uma constante em termos de redução do seu impacte no orçamento das empresas fornecedoras destes produtos. É neste contexto que surge a necessidade da realização deste estudo de Benchmark de Softwares, tornando-se bastante importante, quer ao nível da competitividade industrial, quer ao nível da inovação para novos produtos. A análise por elementos finitos desempenha um papel primordial no tryout virtual e otimização das ferramentas e processos de conformação plástica. Os objetivos principais deste estudo de simulação numérica são a identificação e comparação dos resultados obtidos pelo AUTOFORM e pelo PAMSTAMP, para cada uma das variáveis identificadas como as mais influentes na robustez dos processos de estampagem de chapa metálica. Estas variáveis identificadas são: consumo de material (Draw-in) após conformação; forças de conformação; valores de variação de espessura e dos valores de extensão e resultados de Springback. Os resultados obtidos são comparados com os resultados experimentais e, desta forma, avalia-se a capacidade inovadora e a eficácia de cada um dos softwares, obtendo-se assim, uma orientação mais real para o software mais indicado aos objetivos impostos pela indústria automóvel. Para este efeito, a indústria automóvel, como maior impulsionador e motor da investigação na área da simulação numérica aplicada aos processos de estampagem, tem aderido em peso ao Benchmarking. Um exemplo disto, é o que acontece nas conferências Numisheet. O Benchmark #2 da conferência Numisheet 2008 é analisado pormenorizadamente e os resultados numéricos e experimentais são comparados e apresentados. Dois materiais distintos (aço HC260LAD e liga de alumínio AC170), assim como três modelos com geometrias diferentes (com e sem freios) são apresentados neste relatório. Com vista à redução dos ciclos tentativa-erro, tem-se adotado ciclos virtuais ou numéricos e tem-se incrementado a interatividade entre as fases de concepção e projeto, num conceito muito próprio, mas cada vez mais abrangente, denominado “produção virtual”. É nesta filosofia que se insere a simulação numérica dos processos de conformação de chapa.

Determination of drawbead contacts with variable bead penetration

In stamping operations, the sliding of the sheet metal over the drawbeads is of great importance. The geometry of the drawbead and the degree of penetration both influence material flow and alter the frictional effects between the work and the tool. The effect of drawbead penetration over drawbeads has been studied using the Drawbead Simulator (DBS) test. The contact phenomenon between the sheet and drawbeads was analysed by examining deformed samples with an image fitting technique. The results were compared with an FE simulation and with an approximate geometric analysis. The results give a useful relationship between the rates of change of the contact angle with increasing bead penetration.

Electron back scattered diffraction (EBSD) characterization of warm rolled and accumulative roll bonding (ARB) processed ferrite

An interstitial free (IF) steel was severely deformed using accumulative roll bonding (ARB) process and warm rolling. The maximum equivalent strains for ARB and warm rolling were 4.8 and 4.0, respectively. The microstructure and micro-texture were studied using optical microscopy and scanning electron microscopy equipped with electron back scattered diffraction (EBSD). The grain size and misorientation obtained by both methods are in the same range. The microstructure in the ARB samples after 6 cycles is homogeneous, although a grain size gradient is observed at the layers close to the surface. The through thickness texture gradient in the ARB samples is different from the warm rolled samples. While a shear texture (⟨110⟩//rolling plane normal direction (ND)) at the surface and rolling texture at the center region is developed in the ARB  samples, the overall texture is weak. The warm rolled samples display a sharp rolling texture through the thickness with increasing the sharpness toward the center. These differences are attributed to the fact that the central region of ARB strip is comprised of material that was once at the surface. The ARB process  can suppress the formation of shear bands which are conventional at warm rolled IF steels. EBSD study on the sample with 6th cycle of ARB following the annealing at 750 ◦C verified a texture gradient through the thickness of the sheet. The shear orientations at the surface and at the quarter thickness layers can be identified even after annealing. The overall weak texture and existence of shear orientations make ARB processed samples unfavorable for sheet metal forming in compare with warm rolled samples.

Multi-scale modelling of DP590 steel

Dual Phase (DP) steel one of the Advanced High Strength Steels (AHSS) has a two phase microstructure where soft and hard phase acts together to offer a high strength composite effect. The high strength, however, must be balanced with ductility so that complex parts and designs can be manufactured from AHSS sheets. However, during forming certain grades of DP steel a sudden crack can occur without any intimation of necking. Thus, due to this abnormal forming behaviour, is difficult to accurately predict because most classical modelling approaches are not designed for such micro-structurally heterogeneous materials. These modelling approaches are generally based on an average representation of the material behaviour in a continuum mechanics formulation. This works for materials that are homogenous, or at least could be assumed to be homogenous at scales lower than the naked eye can see. However, for a material like AHSS, the microstructure plays a significant role in dictating the mechanical behaviour at the macro-scale. This paper studies the multi-scale modelling ofDP590 steel. It is found that the sufficient accuracy can be achieved from multi-scale modelling while comparing with the experiments.

Anisotropic behavior in plasticity and ductile fracture of an aluminum alloy

Anisotropic mechanical behavior is investigated for an aluminum alloy of 6K21-IH T4 both in plastic deformation and ductile fracture. Anisotropic plastic deformation is characterized by uniaxial tensile tests of dog-bone specimens, while anisotropy in ductile fracture is illustrated with specimens with a central hole, notched specimens and shear specimens. All these specimens are cut off at every 15º from the rolling direction. The r-values and uniaxial tensile yield stresses are measured from the tensile tests of dog-bone specimens. Then the anisotropic plasticity is modeled by a newly proposed J2-J3 criterion under non-associate flow rule (non-AFR). The testing processes of specimens for ductile fracture analysis are simulated to extract the maximum plastic strain at fracture strokes as well as the evolution of the stress triaxiality and the Lode parameter in different testing directions. The measured fracture behavior is described by a shear-controlled ductile fracture criterion proposed by Lou et al. (2014. Modeling of shear ductile fracture considering a changeable cut-off value for stress triaxiality. Int. J. Plasticity 54, 56-80) for different loading directions. It is demonstrated that the anisotropic plastic deformation is described by the J2-J3 criterion with high accuracy in various loading conditions including shear, uniaxial tension and plane strain tension. Moreover, the anisotropy in ductile fracture is not negligible and cannot be modeled by isotropic ductile fracture criteria. Thus, an anisotropic model must be proposed to accurately illustrate the directionality in ductile fracture.

Computer aided form roll design

Cold roll forming is an extremely important but little studied sheet metal forming process. In this thesis, the process of cold roll forming is introduced and it is seen that form roll design is central to the cold roll forming process. The conventional design and manufacture of form rolls is discussed and it is observed that surrounding the design process are a number of activities which although peripheral are time consuming and a possible source of error. A CAD/CAM system is described which alleviates many of the problems traditional to form roll design. New techniques for the calculation of strip length and controlling the means of forming bends are detailed. The CAD/CAM system's advantages and limitations are discussed and, whilst the system has numerous significant advantages, its principal limitation can be said to be the need to manufacture form rolls and test them on a mill before a design can be stated satisfactory. A survey of the previous theoretical and experimental analysis of cold roll forming is presented and is found to be limited. By considering the previous work, a method of numerical analysis of the cold roll forming process is proposed based on a minimum energy approach. Parallel to the numerical analysis, a comprehensive range of software has been developed to enhance the designer's visualisation of the effects of his form roll design. A complementary approach to the analysis of form roll design is the generation of form roll design, a method for the partial generation of designs is described. It is suggested that the two approaches should continue in parallel and that the limitation of each approach is knowledge of the cold roll forming process. Hence, an initial experimental investigation of the rolling of channel sections is described. Finally, areas of potential future work are discussed.

Disseny dels elements constitutius per adaptar un centre de mecanitzat de control numèric a la tecnologia Incremental Sheet Forming (ISF)

Un dels processos tradicionals de conformació de xapa més utilitzats a nivell industrial, degut a la seva rapidesa d’operació i la seva maduresa del procés, és l’embotició. Per a dur a terme aquest procés és necessària la construcció d’uns utillatges (matriu i punxó) per a cada tipus de producte. Aquests utillatges estan fabricats amb materials altament resistents ja que han de poder suportar càrregues molt importants durant la deformació. A més, s’han de garantir unes precisions dimensionals molt bones per tal d’evitar el xoc entre les dues parts de l’utillatge i per a assegurar que la peça obtinguda tingui les dimensions desitjades. Aquest fet implica que el procés d’obtenció de les matrius i punxons tingui un cost molt elevat i per a amortitzar-lo és necessari que la producció sigui en massa.L’objecte d’aquest projecte és adaptar el centre de mecanitzat Kondia HS1000 per tal de poder dur a terme recerca bàsica de la tecnologia de conformat incremental de xapa (ISF) en el Grup de Recerca en Enginyeria del Producte, Procés i Producció (GREP)

Sheet forming simulation for AHSS components in the automotive industry

The trend in the automotive industry towards new advanced high strength steels (AHSS), combined with the ongoing reduction in program lead times have increased the need to get tool designs right, first time. Despite the fact that the technology used by sheet metal stamping companies to design and manufacture tooling is advancing steadily, finding optimal process parameters and tool geometries remains a challenge. Consequently, there has been a transition from designs based largely on trial and error techniques and the experience of the stamping engineer, to the increased use of virtual manufacturing and finite element (FE) simulation predictions as an indispensable tool in the design process. This work investigates the accuracy of FE techniques in predicting the forming behavior of AHSS grades, such as TRIP and dual phase, as compared to more commonly used conventional steel grades. Three different methods of simulation, one-step, implicit and explicit techniques, were used to model the forming process for an automotive part. Results were correlated with experimental strain and thickness measurements of manufactured components from the production line.

Review of approximate analyses of sheet forming processes

Approximate models are often used for the following purposes: in on-line control systems of metal forming processes where calculation speed is critical; to obtain quick, quantitative information on the magnitude of the main variables in the early stages of process design; to illustrate the role of the major variables in the process; as an initial check on numerical modelling; and as a basis for quick calculations on processes in teaching and training packages. The models often share many similarities; for example, an arbitrary geometric assumption of deformation giving a simplified strain distribution, simple material property descriptions - such as an elastic, perfectly plastic law - and mathematical short cuts such as a linear approximation of a polynomial expression. In many cases, the output differs significantly from experiment and performance or efficiency factors are developed by experience to tune the models. In recent years, analytical models have been widely used at Deakin University in the design of experiments and equipment and as a pre-cursor to more detailed numerical analyses. Examples that are reviewed in this paper include deformation of sandwich material having a weak, elastic core, load prediction in deep drawing, bending of strip (particularly of ageing steel where kinking may occur), process analysis of low-pressure hydroforming of tubing, analysis of the rejection rates in stamping, and the determination of constitutive models by an inverse method applied to bending tests.