Crystallization kinetics and morphology of nylon 1212

The isothermal and non-isothermal crystallization processes of nylon 1212 were investigated by polarized optical microscopy. The crystal growth rates of nylon 1212 measured in isothermal conditions at temperatures ranged from 182 to 132 degreesC are well comparable with those measured by non-isothermal procedures (cooling rates ranged from 0.5 to 11 degreesC/min). The kinetic data were examined with the Hoffman-Lauritzen nucleation theory on the basis of the obtained values of the thermodynamic parameters of nylon 1212. The classical regime I --> II and regime II --> III transitions occur at the temperatures of 179 and 159 degreesC, respectively. The crystal growth parameters were calculated with (100) plane assumed to be the growth plane. The regime I --> II --> III transition is accompanied by a morphological transition from elliptical-shaped structure to banded spherulite and then non-banded spherulite. The development of morphology during isothermal and non-isothermal processes shows a good agreement.

Isothermal and nonisothermal melt-crystallization kinetics of syndiotactic polystyrene

Analyses of the isothermal and nonisothermal melt kinetics for syndiotactic polystyrene have been performed with differential scanning calorimetry, and several kinetic analyses have been used to describe the crystallization process. The regime II-->III transition, at a crystallization temperature of 239degrees, is found. The values of the nucleation parameter K-g for regimes II and III are estimated. The lateral-surface free energy, sigma = 3.24 erg cm(-2), the fold-surface free energy, sigma(e) = 52.3 +/- 4.2 erg cm(-2), and the average work of chain folding, q = 4.49 +/- 0.38 kcal/mol, are determined with the (040) plane assumed to be the growth plane. The observed crystallization characteristics of syndiotactic polystyrene are compared with those of isotactic polystyrene. The activation energies of isothermal and nonisothermal melt crystallization are determined to be DeltaE = -830.7 kJ/mol and DeltaE = -315.9 kJ/mol, respectively.

Crystal growth and structural analysis of PrMnO3 and TbMnO3

Single crystals of PrMnO3 and TbMnO3 were grown by floating zone method and the crystal structure was determined by single crystal X-ray diffractometry. The structure of these compounds belongs to the orthorhombic system (space group is Pnma, No. 62) with the lattice parameters alpha approximate to root (.) - a(p), b approximate to 2 (.) a(p) , c approximate to root 2.a(p) and Z = 4, where a(p) is ideal cubic perovskite cell parameter.

Studies on the morphology transition of micro-crystal growth in polymer films in high vacuum and strong electrostatic field

The morphology of films of isotactic polypropylene poly (3-dodecylthiophene) and iPP/P3DDT blend formed in electrostatic fields has been investigated by using scanning electron microscope. The experiment results show that the micro-crystal morphology of polymer films was strongly dependent on electrostatic fields. It was found that the effect of the electrostatic field led to the formation of dendrite crystals aligned in the field direction, and some branches of P3DDT ruptured. However, the micro-crystals in these films grew into spherulites without electrostatic field,and have no crystal orientation.

Crystallization kinetics of poly(ether ether ketone) (PEEK) from its metastable melt

After isothermal crystallization of the amorphous poly(ether ether ketone), double endothermic behaviour can be found through differential scanning calorimetry experiments. During the heating scan of semicrystalline PEEK, a metastable melt, which comes from the melt of the thinner lamellar crystal populations, can be obtained between these two endotherms. The metastable melt can recrystallize immediately just above the lower melting temperature and form slightly thicker lamellae than the original ones. The thickness and the perfection depend upon the crystallization time and the crystallization temperature. By comparing the TEM morphological observations of the samples before and after partial melting, it can be shown that lamellar crystals, having different thermodynamic stability, form during isothermal crystallization. After partial melting, only the type of lamellar crystal exhibiting the higher thermodynamic stability remains. Wide angle X-ray diffraction measurements shows a slightly change in the crystallinity of the samples before and after the partial melting. Small angle X-ray scattering results exhibit a change in the long period of the lamellar crystals before and after the partial melting process. The crystallization kinetics of the metastable melt can be determined by means of differential scanning calorimetry. The kinetic analysis showed that the isothermal crystallization of the metastable PEEK melt proceeds with an Avrami exponent of n = 1.0 similar to 1.4, reflecting that probably one-dimensional or an irregular line growth of the crystal occurred between the existing main lamellae with heterogeneous nucleation. (C) 1998 Elsevier Science Ltd. All rights reserved.

Crystal growth and TG-DTA properties of K(2)Ln(NO3)(5).2H(2)O (Ln = La, Ce, Pr, Nd, Sm)

Single crystals of KLnN(Ln=La, Ce, Pr, Nd, Sm) can be grown in water solution with pH approximate to 1 similar to 2 at about 40 degrees C. Crystals of KLnN (Ln=La, Ce, Pr, Nd) are orthorhombic with space group Fdd2. KPrN crystal was grwon and its crystal structure was determined for the first time. The KPrN crystal parameters obtained by the direct method are as follows: a=21.411(3) Angstrom, b=11.2210(10)Angstrom, c=12.208(2) Angstrom, Z=6, R=0.0240. The TG-DTA curves of KLnN(Ln=La,Ce, Pr, Nd, Sm) demonstrate that the processes of dehydration, melt, irreversible phase transition and decomposition of NO3- take place in sequence with the temperature increasing(except KCN). There are three steps in the decomposition of NO3- in KLnN(Ln=La, Nd, Sm) while two steps in KLnN (Ln=Ce, Pr). K(2)Ln(NO3)(5). 2H(2)O are formed at about 225 degrees C by the reaction of the starting materials of KNO3 and Ln(NO3)(3). nH(2)O.

Single crystal growth and spectroscopic properties of KZnF3:Eu3+

Single crystal of KZnF3 : Eu3+ has been grown by means of Bridgman-Stockbarger technique in Ar atmosphere, The emission and excitation spectra of europium ion were measured, The results show that a small amount of Eu2+ exists in the crystal, The existence of Eu2+ ions was also confirmed by ESR data, The valence change of Eu ions during the crystal growth is due to unequivalent substitution of Eu3+ ions for the lattice ions. The sites possibly occupied by Eu ions in this crystal were also discussed.

Poly(epsilon-capralactone)/poly(ethylene oxide) diblock copolymer .2. Nonisothermal crystallization and melting behavior

The nonisothermal crystallization behavior and melting process of the poly(epsilon-caprolactone) (PCL)/poly(ethylene oxide) (PEG) diblock copolymer in which the weight fraction of the PCL block is 0.80 has been studied by using differential scanning calorimetry (DSC). Only the PCL block is crystallizable, the PEO block with 0.20 weight fraction cannot crystallize. The kinetics of the PCL/PEO diblock copolymer under nonisothermal crystallization conditions has been analyzed by Ozawa's equation. The experimental data shows no agreement with Ozawa's theoretical predictions in the whole crystallization process, especially in the later stage. A parameter, kinetic crystallinity, is used to characterize the crystallizability of the PCL/PEO diblock copolymer. The amorphous and microphase separating PEO block has a great influence on the crystallization of the PCL block. It bonds chemically with the PCL block, reduces crystallization entropy, and provides nucleating sites for the PCL block crystallization. The existence of the PEO block leads to the occurrence of the two melting peaks of the PCL/PEO diblock copolymer during melting process after nonisothermal crystallization. The comparison of nonisothermal crystallization of the PCL/PEO diblock copolymer, PCL/PEO blend, and PCL and PEO homopolymers has been made. It showed a lower crystallinity of the PCL/PEO diblock copolymer than that of others and a faster crystallization rate of the PCL/PEO diblock copolymer than that of the PCL homopolymer, but a slower crystallization rate than that of the PCL/PEO blend. (C) 1997 John Wiley & Sons, Inc.

Crystal structure and its transition for poly(aryl ether ketone ketone)s .1.

Poly(aryl ether ketone ketone)s (PEKK) was a high-performance engineering plastics, By means of Wide Angle X-ray Diffraction (WAXD) and Differential Scanning Calorimetry (DSC) methods, PEKK samples crystallized in solvent induction, from glass state and from melting state were studied, Crystal forms I and II for PEKK were found, The formation of crystal form II was dependent on thermal history and solvent induction, and this form II had melting point 10 degrees C or so lower than that of form I crystallized from glass state, All PEKK samples had low melting peaks which were relevant to the polarization of PEKK molecular chain, while they had nothing to do with thermal history, The heat of fusion for PEKK low melting peaks accounted for,percentage of 2 to 10 or so of the whole heat of fusion, And PEKK has its equilibrium melting point of 409 degrees C.

Miscibility and phase behavior in blends containing random copolymers of poly(ether ether ketone) and phenolphthalein poly(ether ether ketone)

The miscibility and phase behavior of polysulfone (PSF) and poly(hydroxyether of bisphenol A) (phenoxy) with a series of copoly(ether ether ketone) (COPEEK), a random copolymer of poly(ether ether ketone) (PEEK), and phenolphthalein poly(ether ether ketone) (PEK-C) was studied using differential scanning calorimetry. A COPEEK copolymer containing 6 mol % ether ether ketone (EEK) repeat units is miscible with PSF, whereas copolymers containing 12 mol % EEK and more are not. COPEEK copolymers containing 6 and 12 mol % EEK are completely miscible with phenoxy, but those containing 24 mol % EEK and more are immiscible with phenoxy. Moreover, a copolymer containing 17 mol % EEK is partially miscible with phenoxy; the blends show two transitions in the midcomposition region and single transitions at either extreme. Two T(g)s were observed for the 50/50 blend of phenoxy with the copolymer containing 17 mol % EEK, whereas a single composition-dependent T-g appeared for all the other compositions. An FTIR study revealed that there exist hydrogen-bonding interactions between phenoxy and the copolymers. The strengths of the hydrogen-bonding interactions in the blends of the COPEEK copolymers containing 6 and 12 mol % EEK are the same as that in the phenoxy/PEK-C blend. However, for the blends of copolymers containing 17, 24, and 28 mol % EEK, the hydrogen-bonding interactions become increasingly unfavorable and the self-association of the hydroxyl groups of phenoxy is preferable as the content of EEK units in the copolymer increases. The observed miscibility was interpreted qualitatively in terms of the mean-field approach. (C) 1996 John Wiley & Sons, Inc.

GLASS-TRANSITION AND CRYSTALLIZATION OF POLY(VINYL ALCOHOL)-G-POLY(METHYL METHACRYLATE) GRAFT-COPOLYMERS

The glass transition behaviour, microphase separation morphology and crystallization of poly(vinyl alcohol)-g-poly(methyl methacrylate) graft copolymers (PVA-g-PMMA) were studied. A lamellar microphase separation morphology was formed, even for a copolyme

CRYSTALLIZATION KINETICS OF MIXTURES OF POLY(EPSILON-CAPROLACTONE) AND POLY(STYRENE-CO-ACRYLONITRILE)

The crystallization kinetics in mixtures of poly(epsilon-caprolactone) (PCL) and poly(styrene-co-acrylonitrile) (SAN) has been investigated as the function of composition and crystallization temperature. The isothermal growth rates of PCL spherulites decrease with increasing concentration of SAN. Because of the miscibility of PCL/SAN mixtures, the radial growth rates of the spherulites are described by a kinetic equation including the interaction parameter and the free energy for the formation of crystal nuclei. The interaction parameter obtained from the fitting of the kinetic equation with experimental data is in good agreement with that obtained from melting point depression. Folding surface free energies decrease with the increase of SAN concentration. In light of these results, it is suggested that, for the PCL/SAN mixtures, the noncrystallizable SAN polymer reduces the mobility of crystallizable PCL polymer so that the growth rates decrease with the increase of noncrystallizable component fraction.

Influence of several non-nutrient additives on nonspecific immunity and growth of juvenile turbot, Scophthalmus maximus L.

The effects of three non-nutrient additives on nonspecific immunity and growth of juvenile turbot (Scophthalmus maximus L.) were studied in this feeding experiment. The five treatments are basal diet alone, basal diets containing three different additives [0.4 g kg(-1) of xylo-oligosaccharides (XOS), 1.3 g kg (-1) of yeast cell wall and 0.8 g kg (-1) of bile acids] individually or in combination. Two hundred and twenty-five turbots (average initial weight 151.3 +/- 11.3 g) were randomly allotted in five treatments with three replicates within each treatment in a 72-day period. Comparing with basal diet group, activities of C3, C4, phagocyte, lysozyme, specific growth rate and feed conversion rate in yeast cell wall, XOS and the combined groups was enhanced significantly (P < 0.05); however, these parameters in bile acid groups were increased slightly (P > 0.05) except for phagocyte (P < 0.05); superoxide dismutase activity in additive groups was not significantly increased (P > 0.05) except for the combined group (P < 0.05). In conclusion, supplementation of yeast cell wall and XOS enhanced the nonspecific immunity of juvenile turbot. Synergistic or additive effect of the three additives was not observed.

Effects of magnetic fields on crystal growth

The effects of a constant uniform magnetic field on dendritic solidification were investigated using a 2-dimensional enthalpy based numerical model. The interaction between thermoelectic currents and the magnetic field generates a Lorentz force that creates a flow. This flow causes a change in the morphology of the dendrite; secondary growth is promoted on one side of the dendrite arm and the tip velocity of the primary arm is increased.

Effects of magnetic fields on crystal growth

The effects of a constant uniform magnetic field on thermoelectric currents during dendritic solidification were investigated using an enthalpy based numerical model. It was found that the resulting Lorentz force generates a complex flow influencing the solidification pattern. Experimental work of material processing under high magnetic field conditions has shown that the microstructure can be significantly altered. There is evidence that these effects can be atrtributed to the Lorentz force created through the thermoelectric magentohydrodynamic interactions.[1,2] However the mechanism of how this occurs is not very well understood. In this paper, our aim is to investigate the flow field created from the Lorentz force and how this influences the morphology of dendritic growth for both pure materials and binary alloys.