Utilization of teflon and aluminum oxide for wheel cleaning in Minimum Quantity Lubrication (MQL) grinding

Researches concerning cooling-lubrication optimization in grinding have been conducted to contribute to a more sustainable process. An alternative to flood coolant is minimum quantity lubrication (MQL), which spray oil droplets in a compressed air jet. However, problems related to wheel cleaning were reported, due to wheel loading by a mixture of chips and oil, resulting in worsening of surface quality. This work aims to evaluate the viability of Teflon and aluminum oxide for wheel cleaning, compared to MQL without cleaning and MQL with cleaning by compressed air, through the following output variables: surface roughness, roundness, wheel wear, grinding power and acoustic emission. Vickers microhardness measurements and optical microscopy were also carried out. The results showed that both materials were efficient in cleaning the wheel, compared to MQL without cleaning, but not as satisfactory as compressed air. Much work is to be done in order to select the right material for wheel cleaning.

Impact of Quantity of Resin, C-factor, and Geometry on Resin Composite Polymerization Shrinkage Stress in Class V Restorations

Objective: This study evaluated the effect of quantity of resin composite, C-factor, and geometry in Class V restorations on shrinkage stress after bulk fill insertion of resin using two-dimensional finite element analysis.Methods: An image of a buccolingual longitudinal plane in the middle of an upper first premolar and supporting tissues was used for modeling 10 groups: cylindrical cavity, erosion, and abfraction lesions with the same C-factor (1.57), a second cylindrical cavity and abfraction lesion with the same quantity of resin (QR) as the erosion lesion, and then all repeated with a bevel on the occlusal cavosurface angle. The 10 groups were imported into Ansys 13.0 for two-dimensional finite element analysis. The mesh was built with 30,000 triangle and square elements of 0.1 mm in length for all the models. All materials were considered isotropic, homogeneous, elastic, and linear, and the resin composite shrinkage was simulated by thermal analogy. The maximum principal (MPS) and von Mises stresses (VMS) were analyzed for comparing the behavior of the groups.Results: Different values of angles for the cavosurface margin in enamel and dentin were obtained for all groups and the higher the angle, the lower the stress concentration. When the groups with the same C-factor and QR were compared, the erosion shape cavity showed the highest MPS and VMS values, and abfraction shape, the lowest. A cavosurface bevel decreased the stress values on the occlusal margin. The geometry factor overcame the effects of C-factor and QR in some situations.Conclusion: Within the limitations of the current methodology, it is possible to conclude that the combination of all variables studied influences the stress, but the geometry is the most important factor to be considered by the operator.

Utilization of Minimum Quantity Lubrication (MQL) with Water in CBN Grinding of Steel

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of the quantity of coloring agent in bleaching gels activated with LED/laser appliances on bleaching efficiency

The aim of this study was to assess the influence of the quantity of coloring agent on the bleaching efficiency of gels containing 35% H2O2. Sixty human third molars were sectioned mesiodistally, darkened in a coffee solution and sectioned in the occlusal-cervical direction, resulting in mesial (not bleached) and distal halves (bleached). They were distributed into three groups: Whiteness HP, Total Bleach, and Whiteform Perox Red Gel; and subdivided into four sub-groups: no coloring agent, manufacturer's standard, double the standard, and triple the standard. The gels were activated with light-ermitting diode/laser appliances. The images were analyzed with the Adobe Photoshop program (deltaEL*a*b*). The variation was submitted to the ANOVA test (two factors: type of gel and quantity of coloring agent) and Tukey test. Differences were observed for the quantity of coloring agent. The mean (+/-SD) was determined for each quantity of coloring used: no coloring agent -6.85 (+/-2.26)a, manufacturer's standard -794 (+/-2.55)ab, double the standard -8.65 (+/-2.47)b, triple the standard -9.05 (+/-2.72)b. In conclusion, the standard quantity of coloring agent did not provide significantly more intense bleaching than when it was completely absent. The use of double and triple the amount provided greater bleaching than that observed for the gel without coloring agent. No significant differences were observed between the tested gels.

A study on the viability of minimum quantity lubrication with water in grinding of ceramics using a hybrid-bonded diamond wheel

With the currently strict environmental law in present days, researchers and industries are seeking to reduce the amount of cutting fluid used in machining. Minimum quantity lubrication is a potential alternative to reduce environmental impacts and overall process costs. This technique can substantially reduce cutting fluids in grinding, as well as provide better performance in relation to conventional cutting fluid application (abundant fluid flow). The present work aims to test the viability of minimum quantity lubrication (with and without water) in grinding of advanced ceramics, when compared to conventional method (abundant fluid flow). Measured output variables were grinding power, surface roughness, roundness errors and wheel wear, as well as scanning electron micrographs. The results show that minimum quantity lubrication with water (1:1) was superior to conventional lubrication-cooling in terms of surface quality, also reducing wheel wear, when compared to the other methods tested.

Quality and quantity of milk produced by Saanen goats submitted to stress during three sequential days

The experiment aimed to study the effect of physiological stress on cortisol levels, quality and quantity of milk through punctual administration of ACTH. Twelve Saanen goats were divided in two experimental groups: ACTH group (0,5 mu g of ACTH/Kg.L.W); Placebo group (placebo solution). Milk production, and percentages of protein, fat, lactose and SCC (somatic cells counting) of the milk were analyzed before, during and after the administration of ACTH/placebo. Simultaneously to the ACTH/placebo administration and during three sequential days, blood was collected to evaluate cortisol concentrations. At times -30 and zero, both groups presented basal concentrations of cortisol. The increase of cortisol contents was significant at times 60 (group ACTH: 59.00 +/- 5.70 and groups placebo: 5.23 +/- 1.37ng/mL) and 120 (group ACTH: 47.96 +/- 9.72 and group placebo: 4.38 +/- 1,14ng/mL) since the cortisol content was higher on the ACTH group. The values returned to the basal level at 300 minutes. Concerning milk production, no differences were found between ACTH and placebo groups. Milk, protein, fat, lactose and SCC did not distinguish one group from another. The results indicated that the physiological stress induced during three days was not harmful to milk production and milk quality of Saanen goats.

Genetic analyses of smoking initiation, persistence, quantity, and age-at-onset of regular cigarette use in Brazilian families: the Baependi Heart Study

Background: The purpose of this study was to estimate the genetic influences on the initiation of cigarette smoking, the persistence, quantity and age-at-onset of regular cigarette use in Brazilian families. Methods: The data set consisted of 1,694 individuals enrolled in the Baependi Heart Study. The heritability and the heterogeneity in genetic and environmental variance components by gender were estimated from variance components approaches, using the SOLAR (Sequential Oligogenic Linkage Analysis Routines) computer package. The mixed-effects Cox model was used for the genetic analysis of the age-at onset of regular cigarette use. Results: The heritability estimates were high (> 50%) for smoking initiation and were intermediate, ranging from 23.4 to 31.9%, for smoking persistence and quantity. Significant evidence for heterogeneity in variance components by gender was observed for smoking initiation and age-at-onset of regular cigarette use. Genetic factors play an important role in the interindividual variation of these phenotypes in females, while in males there is a predominant environmental component, which could be explained by greater social influences in the initiation of tobacco use. Conclusions: Significant heritabilities were observed in smoking phenotypes for both males and females from the Brazilian population. These data add to the literature and are concordant with the notion of significant biological determination in smoking behavior. Samples from the Baependi Heart Study may be valuable for the mapping of genetic loci that modulate this complex biological trait.

INFLUENCE OF DISCOUNT PRICE ANNOUNCEMENTS ON CONSUMER'S BEHAVIOR

The theoretical framework that underpins this research study is based on the Prospect Theory formulated by Kahneman and Tversky, and Thaler's Mental Accounting Theory. The research aims to evaluate the consumers' behavior when different patterns of discount are offered (in percentage and absolute value and for larger and smaller discounts). Two experiments were conducted to explore these patterns of behavior and the results that were obtained supported the view that the framing effect was a common occurrence. The patterns of choice of individuals in a sample were found to be different due to changes in the ways discounts were offered. This can be explained by the various ways of presenting discount rates that had an impact on the influence of purchase intentions, recommendations and quality perception.

Influence of discount price announcements on consumer's behavior

The theoretical framework that underpins this research study is based on the Prospect Theory formulated by Kahneman and Tversky, and Thaler's Mental Accounting Theory. The research aims to evaluate the consumers' behavior when different patterns of discount are offered (in percentage and absolute value and for larger and smaller discounts). Two experiments were conducted to explore these patterns of behavior and the results that were obtained supported the view that the framing effect was a common occurrence. The patterns of choice of individuals in a sample were found to be different due to changes in the ways discounts were offered. This can be explained by the various ways of presenting discount rates that had an impact on the influence of purchase intentions, recommendations and quality perception.