Análise dinâmica e estrutural de virabrequim

This paper deals with static analysis and dynamic stress of an ensemble crank and crankshaft, contained within a combustion engine of 4 cylinders. Aimed to illustrate procedures for computer-aided analysis having as goal the optimization of components according to the need for the market demand. Thus, to work in static and dynamic analyzes were summarized the basic theory involved in the calculations and analyzes necessary actuation forces and held a brief introduction about the manufacturing process and forging. Subsequently, it was applied with the use of software in a case the crankshaft, to obtain the performance and structural dynamic thereof. There was a conservative result and critical points in the fillet of the crankshaft bearing, as well as for lubrication hole. It was concluded that there are possibilities for improvements in the manufacturing process and design optimization in order to provide lower criticality and a more robust part

Estudo das propriedades mecânicas da madeira plástica

This work has in its outline the analysis of the mechanical properties of the composition of plastic residues, denominated “plastic wood”, aiming at establishing technical parameters for application of this material in substitution to the natural wood. Plastic-Wood is basically, a combination of several kind of plastic, previously selected, washed, dried and without metallic particles, which are agglomerated, extruded or introduced into a mold. The manufacturer can choose different formats and colors. During this monograph it can be observed the use of several kind of plastic, their mechanical properties and the plastic-wood production process. Also are presented features and applications of natural wood, in order to better compare their uses in several applications

Obtenção e caracterização de compósitos via RTM com alta fração de fibras de carbono processados à temperatura ambiente

After confirming the high specific mechanical properties of composite materials by scientific studies conducted over the last decades, one of the challenges of this new class of materials is the ability to achieve mass production at a more affordable cost, which has become indispensable. The Resin Transfer Molding (RTM) is an excellent method for manufacturing composite materials. Despite being a process widely used by international companies in the production of high performance structural composites, only a short time the national aviation industry has shown interest in implementing this type of processing to more complex structures and greater structural responsibility. In aeronautical projects, the reproducibility and the relative low cost of this process, several studies have been performed in Brazil for learning and perfecting this technique. This process is suitable for producing polymer components both simple as complex geometry, and allows to achieve consistent thickness, with high quality finish and without limiting range. Polymeric composite components for the high mechanical stress applications such as aircraft structures, satellites, etc., require a strict control of volume fractions of the composite constituents, beyond the knowledge of their mechanical and thermal properties. Therefore, in this experimental work degree study on the mechanical, thermal and of porosity composites processed by RTM processed characterization was performed. This characterization was performed targeting a possible aerospace application of this composite material. For the production of composites, process equipment (RTM RTM injector Radius 2100cc) was used. The processed carbono/epoxy composites were characterized via flexure tests mechanically and thermally analysis via DMA, DSC and TGA. To determine the volume fraction of fibers, the composite samples were analyzed via matrix digestion (ASTM D3171) ... (Complete abstract click electronic access below)

Diagnóstico ambiental de atividades de mineração com ênfase em olarias no município de Rio Claro (SP)

The environmental diagnosis of any area affected for mining activities contributes in a positive form for the analysis of the characteristics of the environment, biological and social, thus being able to establish control parameters. The clay extration for red ceramics promotes the environment degradation as any another one cultivates of mineral goods, but in lesser scale, which had to the dimensions of potteries. Being thus, some decurrent environment characteristics of the clay extration had been inquired clearly used for potteries located in the city of Rio Claro, SP. For this, the followed method was the cadastre of these areas and potteries in created tables, searching, with this, the contribution for the involved people in the extract activity of related potteries and the facilitation in the visualization of the main problems, necessities and proposals for each one. It could be perceived that the environmental diagnosis of the areas had in common presented referring points to the places where if they find the activities. The same ones are located in the region the northwest of Rio Claro and well next one to the others. Moreover, they have in common, referring characteristics to the process of manufacture of bricks. In common, all the responsibility for the administration and course of the activities competes to the proper families, since the administrative part, even though to the process of manufacture of the bricks. Moreover, from the comment of the areas through field work, the prominent use of diverse areas in the region for the clay extration is noticed, making with that the region has great importance in the regional scene.

Microbiota contaminante em bebidas lácteas fermentadas comerciais

Lately, the acceptability of fermented dairy beverages has been increased, due to the nutritional benefits, the practical consumption and the low cost of product for the manufacturers, and consequently for final market price to the consumers. During the manufacturing process, these products can be susceptible to microbiological contamination. The present study investigated the contaminant microbiota in fermented dairy beverages produced by small- and medium-sized companies, by means of analyses on moulds and yeasts counting, determination of the Most Probable Number (MPN) of total and thermo tolerant coliforms, Escherichia coli and Salmonella spp. detection, and determination of pH value. In spite of the absence of Salmonella spp., a high counts of yeasts and moulds were found, and E. coli was detected in five samples (16.67 %); and the sample were classified as “products in poor sanitary conditions”, because they showed thermo-tolerant coliforms counting higher than the standard established by the legislation in force. Therefore, quality programs such as Good Manufacturing Practices (GMP) and Hazard Analysis and Critical Control Points (HACCP) should be employed to prevent any contamination risk, in order to provide safe products to consumers.

Qualidade microbiológica de bebidas lácteas fermentadas, com adição de polpas de frutas, comercializadas na região de São José do Rio Preto, SP.

As bebidas lácteas fermentadas são produtos formulados contendo iogurte, soro de leite, polpa de frutas, além de outras matérias-primas e aditivos permitidos. O produto final deve apresentar os micro-organismos de forma viável e abundante. Sua popularidade vem aumentando significativamente, principalmente devido aos seus benefícios nutricionais, ao menor custo do produto para o fabricante, à redução do preço final para o consumidor e por apresentar baixa viscosidade, sendo consumida como bebida suave e refrescante. Apesar do processo de fabricação ser considerado simples, utilizando-se principalmente os equipamentos disponíveis nas indústrias lácteas, estes produtos podem estar sujeitos à contaminação microbiana, quando não atendidas as condições elementares de higiene e sanidade. Tal contaminação pode ser representada por leveduras, coliformes totais, termotolerantes e bolores. Considerando os aspectos mencionados, o objetivo deste trabalho foi avaliar a qualidade microbiológica de bebidas lácteas fermentadas, com adição de polpas de frutas, comercializadas na região de São José do Rio Preto û SP, por meio das seguintes análises microbiológicas: contagem de bolores e leveduras, determinação do Número Mais Provável (NMP) de coliformes totais, temotolerantes e pesquisa de Escherichia coli e de Salmonella spp. Foi ainda efetuada a determinação do pH eletrométrico. Após a obtenção dos resultados verificou-se que 20% das amostras analisadas não atenderam ao padrão microbiológico estabelecido na legislação vigente, para coliforme termotolerentes, evidenciando positividade na pesquisa de Escherichia coli, sendo por este motivo, considerados como produtos em condições sanitárias insatisfatórias, portanto, produtos impróprios para o consumo humano.(AU)

Estudo da superfície de fibras de carbono após tratamento de implantação iônica por imersão em plasma (3IP)

In this work, plasma immersion ion implantation (PIII) treatments of carbon fibers (CFs) were performed in order to induce modifications of chemical and physical properties of the CF surface aimed to improve the performance of thermoplastic composite. The samples to be treated were immersed in nitrogen or air glow discharge plasma and pulsed at −3.0 kV for 2.0, 5.0, 10.0, and 15.0 min. After PIII processing, the specimens were characterized by atomic force microscopy (AFM), scanning electron microscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). After CFs treatments, the CF/Polypropylene (PP) composites were produced by hot pressing method. Surface morphology of as-received CFs exhibited some scratches aligned along the fibers due to the fiber manufacturing process. After both treatments, these features became deeper, and also, a number of small particles nonuniformly distributed on the fiber surface can be observed. These particles are product of CF surface sputtering during the PIII treatment, which removes the epoxy layer that covers as-received samples. AFM analyses of CF samples treated with nitrogen depicted a large increase of the surface roughness (Rrms value approximately six times higher than that of the untreated sample). The increase of the roughness was also observed for samples treated by air PIII. Raman spectra of all samples presented the characteristic D- and G-bands at approximately 1355 and 1582 cm−1, respectively. Analysis of the surface chemical composition provided by the XPS showed that nitrogen and oxygen were incorporated onto the surface. The polar radicals formed on the surface lead to increasing of the CF surface energy. Both the modification of surface roughness and the surface oxidation contributed for the enhancement of CF adhesion to the polymeric matrix. These features were confirmed ... (Complete abstract click electronic access below)

Desenvolvimento do PFMEA para uma linha de montagem de motores

In modern days is not practicable to link productivity and profitability without discuss the manufactured products quality. It is of great importance, mainly if the company is looking for a Global Class title, both the product and the process in what it is been fabricated, to attend all the high level quality requirements. This work aims to define the necessary steps for implementing a new project, including the initial viability studies, and then the staff approval, passing through the development of tools and documents necessary to its fabrication, purchasing goods and services to build the installation, and the final stage of implementation, focused on the manufacturing process quality. It will be highlighted a quality tool that helps do decrease the process risks and thereafter increase its reliability after the implementation

Usinabilidade e integridade superficial de implantes dentários

Pós-graduação em Engenharia Mecânica - FEIS

Diodo planar orgânico Schottky: construção e caracterização

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Estudo das alterações das propriedades mecânicas em aço A-516 grau 70 soldado e submetido a tratamento térmico de alívio de tensões

Pressure vessels are equipments that require a great care because of their high cost and human life risk in case of fail, and its fabrication methods are different for each manufacturer. Normally, pressure vessels and its parts are fabricated by welding, which may change local properties of metals. The head of a pressure vessel is a very important structural component and it is fabricated by welding and mechanical conformation. Because its excellent mechanical properties, de steel A-516 Grade 70 is often used in manufacturing of large pressure vessels that are subjected to high pressure and temperature, but was verified that its mechanical resistance is decreased when submitted to a tension relief heat treatment. By experience it was defined that before mechanical conformation of the head of a large pressure vessel, the steel should be submitted to a stress relief heat treatment in order to facilitate the mechanical conformation, but there is no quantitative analysis to prove this method and study its possible risks. In the present work the steel A-516 Grade 70 demonstrated a decrease of its mechanical resistance when submitted to a stress relief heat treatment, but keeping above the minimum limit defined in the literature. By other side its ductility was substantially increased, being possible to deduce that the stress relief heat treatment before mechanical conformation is a viable e recommended technique, but with reservations. With the data acquired during the fabrication e preparation of the specimen and the result of the tests, it was possible to elaborate a welding procedure that provides the same results obtained in this present work

Estudo dos compostos voláteis da decomposição térmica dos anti-helmínticos Albendazol e Mebendazol

The albendazole and mebendazole drugs are benzimidazole derivatives and belong to the anthelmintic class. These drugs are particularly recommended for the treatment against worms present in the gastrointestinal tract of animals and humans, by acting directly on the worm metabolism. The need for thermally study drugs is related to all the parameters that these analyzes include: presence or absence of polymorphs, possible changes in the crystallinity of the drugs, as well as the quality control during the manufacturing process thereof. In this study the thermal behavior of anthelmintic albendazole and commercial mebendazole and its recrystallisation in organic solvents, such as acetic acid and formic acid in dimethylformamide to mebendazole, and albendazole were studied using TG-DSC techniques, TG-FTIR, FTIR and XRD. TG-DSC techniques were used so it could collect information about the thermal stability of the compounds steps for thermal decomposition process and also prove its melting temperature. For recrystallization of drugs in organic solvents, the TG-DSC curves were analyzed to compare and determine that the occurrence of polymorphs. The coupled TG-FTIR technique allowed the analysis of volatile products which were released during the thermal decomposition of the commercial mebendazole. The absorption spectroscopy in the infrared region was performed to mebendazole, and albendazole in order to show the difference in functional groups of both, comparing the spectra with commercial drugs and see if there was recrystallized changes in the absorption band where the drug was recrystallized or when heated. The diffraction technique by powder X-ray method was used for comparison of the crystal structures of commercial drugs and recrystallization in organic solvents to identify changes in crystallinity both, which might suggest the formation of polymorphs

Seleção de materiais e design: um método com base nas redes neurais artificiais

Pós-graduação em Design - FAAC

Determinação comparativa do grau de deformação plástica aplicado a componentes obtidos por conformação

The manufacturing process of components of Pressure Vessels has a great importance in the efficiency during the operation and life cycle of the equipment. Taking this into account, the objective of this dissertation was to analyze the methods to determine the strain rate in formed components by measuring the components themselves, and posterior results comparison with the values found in manufacturing standards of Pressure vessels. In this study the whole manufacturing process of a component from a pressure vessel, known as Head or End, was accompanied. Using the methodology obtained from literatures it was possible to execute the relative and logarithmic deformation measurements of these components and compare with the obtained results by means of equations presented in the Standards as AD-Merkblatt and ASME (for pressure vessels). The found results were also compared with the logarithmic methodology, taking into account the deformation of the empirical mesh and the thickness of the components studied. It is possible to conclude from this study that despite the existence of empirical methods of measurement of strain rate in components plastically formed, it is recommended the adoption in all situation of the component manufacturing standard. It can be noticed and explained during the development of this study and through the results found

Determinação comparativa do grau de deformação plástica aplicado a componentes obtidos por conformação

The manufacturing process of components of Pressure Vessels has a great importance in the efficiency during the operation and life cycle of the equipment. Taking this into account, the objective of this dissertation was to analyze the methods to determine the strain rate in formed components by measuring the components themselves, and posterior results comparison with the values found in manufacturing standards of Pressure vessels. In this study the whole manufacturing process of a component from a pressure vessel, known as Head or End, was accompanied. Using the methodology obtained from literatures it was possible to execute the relative and logarithmic deformation measurements of these components and compare with the obtained results by means of equations presented in the Standards as AD-Merkblatt and ASME (for pressure vessels). The found results were also compared with the logarithmic methodology, taking into account the deformation of the empirical mesh and the thickness of the components studied. It is possible to conclude from this study that despite the existence of empirical methods of measurement of strain rate in components plastically formed, it is recommended the adoption in all situation of the component manufacturing standard. It can be noticed and explained during the development of this study and through the results found