Characterisation of combustion related acoustic emission sources for diesel engine condition monitoring

This thesis represents a major step forward in understanding the link between the development of combustion related faults in diesel engines and the generation of acoustic emissions. The findings presented throughout the thesis provide a foundation so that future diesel engine monitoring systems are able to more effectively detect and monitor developing faults. In undertaking this research knowledge concerning engine function and relevant failure mechanisms was combined with different modelling methods to generate a framework that was used to effectively identify fault related activity within acoustic emissions recorded from different engines.

Outdoor Worker Sun Protection Project : a mixed methods intervention to improve sun safety among outdoor workers

Queensland, Australia has one of the highest rates of skin cancer in the world. Outdoor workers are regularly exposed to high doses of ultraviolet radiation, and are at increased risk to develop non-melanoma and melanoma skin cancers. In 2010, a health promotion intervention to improve sun protection among outdoor workers in Queensland commenced. The intervention employed a mixed methods approach and a participatory action research framework. Fourteen workplaces were recruited from building and construction, rural and farming, local government, and public sector organisations. Management and workers were engaged in cycles of assessment, reflection and discussion, planning, implementation and reassessing, over a 14-month intervention period. Overall, at least one workplace representative from each workplace (range 1-3) and in depth focus groups were held with a subset of workers (range 3-16) to assess sun safe behaviours pre and post intervention. Workers’ attitudes, beliefs, knowledge and willingness to engage in sun protection differed depending on workplace characteristics and support. A familiar theme among workers spoke of sun safety as being “common sense” and the “workers individual responsibility”. Often there was a discrepancy in the perceptions of the workers, compared to the view of workplace representatives and the workplaces position or policy on sun safety. In larger workplaces, especially Government Departments, workers were more aware and followed sun safe practices compared to smaller workplaces where sun safety was not a high priority. These results indicate that a workplace culture which places high values on safety and polices more broadly may also have a positive effect on sun safety among outdoor workers as well. In addition, the specific characteristics of the workplace and the outdoor work tasks influence workers willingness to engage in sun safety measures.

Influence of kaolinite/carbon black hybridization on combustion and thermal decomposition behaviors of NR composites

A series of NR composites filled with modified kaolinite (MK), carbon black (CB) and the hybrid fillercontained MK and CB, were prepared by melt blending. The microstructure, combustion and thermaldecomposition behaviors of NR composites were characterized by TEM, XRD, infrared spectroscopy, conecalorimeter test (CCT) and thermal-gravimetric analysis (TG). The results show that the filler hybridizationcan improve the dispensability and shape of the kaolinite sheets in the rubber matrix and change theinterface bond between kaolinite particles and rubber molecules. NR-3 filled by 10 phr MK and 40 phr CBhas the lowest heat release rate (HRR), mass loss rate (MLR), total heat release (THR), smoke productionrate (SPR) and the highest char residue among all the NR composites. Therefore, the hybridization ofthe carbon black particles with the kaolinite particles can effectively improve the thermal stability andcombustion properties of NR composites.

Carrot red leaf and carrot mottle viruses : observations on the composition of the particles in single and mixed infections

Particles of carrot red leaf virus (CRLV; luteovirus group) purified from chervil (Anthriscus cerefolium) contain a single ssRNA species of mol. wt. about 1.8 x 106 and a major protein of mol. wt. about 25000. CRLV acts as a helper for aphid transmission of carrot mottle virus (CMotV; ungrouped) from mixedly infected plants. Virus preparations purified from such plants possess the infectivity of both viruses but contain particles indistinguishable from those of CRLV; some of the particles are therefore thought to consist of CMotV RNA packaged in CRLV coat protein. When RNA from such preparations was electrophoresed in agarose/polyacrylamide gels, CMotV infectivity was associated with an RNA band that migrated ahead of the CRLV RNA band and had an estimated mol. wt. of about 1.5 x 106, similar to that previously found for the infective ssRNA extracted directly from Nicotiana clevelandii leaves infected with CMotV alone. Preparations of dsRNA from CMotV-infected N. clevelandii leaves contained two species: one of mol. wt. about 3.2 x 106, presumably the replicative form of the infective ssRNA, and the other, mol. wt. about 0.9 x 106, of unknown origin and function. The infective agent in buffer extracts of CMotV-infected N. clevelandii was resistant to RNase (although the enzyme acted as a reversible inhibitor of infection at high concentrations) and is therefore not unprotected RNA. It may be protected within the approximately 52 nm enveloped structures previously reported.

Control strategies to prevent total hip replacement-related infections : a systematic review and mixed treatment comparison

OBJECTIVE: To synthesise the available evidence and estimate the comparative efficacy of control strategies to prevent total hip replacement (THR)-related surgical site infections (SSIs) using a mixed treatment comparison. DESIGN: Systematic review and mixed treatment comparison. SETTING: Hospital and other healthcare settings. PARTICIPANTS: Patients undergoing THR. PRIMARY AND SECONDARY OUTCOME MEASURES: The number of THR-related SSIs occurring following the surgical operation. RESULTS: 12 studies involving 123 788 THRs and 9 infection control strategies were identified. The strategy of 'systemic antibiotics+antibiotic-impregnated cement+conventional ventilation' significantly reduced the risk of THR-related SSI compared with the referent strategy (no systemic antibiotics+plain cement+conventional ventilation), OR 0.13 (95% credible interval (CrI) 0.03-0.35), and had the highest probability (47-64%) and highest median rank of being the most effective strategy. There was some evidence to suggest that 'systemic antibiotics+antibiotic-impregnated cement+laminar airflow' could potentially increase infection risk compared with 'systemic antibiotics+antibiotic-impregnated cement+conventional ventilation', 1.96 (95% CrI 0.52-5.37). There was no high-quality evidence that antibiotic-impregnated cement without systemic antibiotic prophylaxis was effective in reducing infection compared with plain cement with systemic antibiotics, 1.28 (95% CrI 0.38-3.38). CONCLUSIONS: We found no convincing evidence in favour of the use of laminar airflow over conventional ventilation for prevention of THR-related SSIs, yet laminar airflow is costly and widely used. Antibiotic-impregnated cement without systemic antibiotics may not be effective in reducing THR-related SSIs. The combination with the highest confidence for reducing SSIs was 'systemic antibiotics+antibiotic-impregnated cement+conventional ventilation'. Our evidence synthesis underscores the need to review current guidelines based on the available evidence, and to conduct further high-quality double-blind randomised controlled trials to better inform the current clinical guidelines and practice for prevention of THR-related SSIs.

Mixed venous oxygen saturation monitoring revisited : thoughts for critical care nursing practice

Background Less invasive methods of determining cardiac output are now readily available. Using indicator dilution technique, for example has made it easier to continuously measure cardiac output because it uses the existing intra-arterial line. Therefore gone is the need for a pulmonary artery floatation catheter and with it the ability to measure left atrial and left ventricular work indices as well the ability to monitor and measure a mixed venous saturation (SvO2). Purpose The aim of this paper is to put forward the notion that SvO2 provides valuable information about oxygen consumption and venous reserve; important measures in the critically ill to ensure oxygen supply meets cellular demand. In an attempt to portray this, a simplified example of the septic patient is offered to highlight the changing pathophysiological sequelae of the inflammatory process and its importance for monitoring SvO2. Relevance to clinical practice SvO2 monitoring, it could be argued, provides the gold standard for assessing arterial and venous oxygen indices in the critically ill. For the bedside ICU nurse the plethora of information inherent in SvO2 monitoring could provide them with important data that will assist in averting potential problems with oxygen delivery and consumption. However, it has been suggested that central venous saturation (ScvO2) might be an attractive alternative to SvO2 because of its less invasiveness and ease of obtaining a sample for analysis. There are problems with this approach and these are to do with where the catheter tip is sited and the nature of the venous admixture at this site. Studies have shown that ScvO2 is less accurate than SvO2 and should not be used as a sole guiding variable for decision-making. These studies have demonstrated that there is an unacceptably wide range in variance between ScvO2 and SvO2 and this is dependent on the presenting disease, in some cases SvO2 will be significantly lower than ScvO2. Conclusion Whilst newer technologies have been developed to continuously measure cardiac output, SvO2 monitoring is still an important adjunct to clinical decision-making in the ICU. Given the information that it provides, seeking alternatives such as ScvO2 or blood samples obtained from femorally placed central venous lines, can unnecessarily lead to inappropriate treatment being given or withheld. Instead when using ScvO2, trending of this variable should provide clinical determinates that are useable for the bedside ICU nurse, remembering that in most conditions SvO2 will be approximately 16% lower.

Paper-based mixed reality sketch augmentation as a conceptual design support tool

This undergraduate student paper explores usage of mixed reality techniques as support tools for conceptual design. A proof-of-concept was developed to illustrate this principle. Using this as an example, a small group of designers was interviewed to determine their views on the use of this technology. These interviews are the main contribution of this paper. Several interesting applications were determined, suggesting possible usage in a wide range of domains. Paper-based sketching, mixed reality and sketch augmentation techniques complement each other, and the combination results in a highly intuitive interface.

H2-O2 porous fuel injection in a radical farming scramjet

This paper reports on the experimental testing of oxygen compatible ceramic matrix composite porous injectors in a nominally two-dimensional hydrogen fuelled and oxygen enriched radical farming scramjet in the T4 shock tunnel facility. All experiments were performed at a dynamic pressure of 146 kPa, an equivalent flight Mach number of 9.7, a stagnation pressure and enthalpy of 40MPa and 4.3 MJ/kg respectively and at a fuelling condition that resulted in an average equivalence ratio of 0.472. Oxygen was pre-mixed with the fuel prior to injection to achieve enrichment percentages of approximately 13%, 15% and 17%. These levels ensured that the hydrogen-oxidiser mix injected into the engine always remained too fuel rich to sustain a flame without any additional mixing with the captured air. Addition of pre-mixed oxygen with the fuel was found to significantly alter the performance of the engine; enhancing both combustion and ignition and converting a previously observed limited combustion condition into one with sustained and noticeable combustion induced pressure rise. Increases in the enrichment percentage lead to further increases in combustion levels and acted to reduce ignition lengths within the engine. Suppressed combustion runs, where a nitrogen test gas was used, confirmed that the pressure rise observed in these experiments as attributed to the oxygen enrichment and not associated with the increased mass injected.

A detailed investigation of nominally 2-D radical-farming scramjet combustion

This paper reports on an investigation of the flow/chemistry coupling inside a nominally two-dimensional inlet-fuelled scramjet configuration. The experiments were conducted at a freestream Mach number of 7.3 and a total flow enthalpy of 4.3MJ/kg corresponding to a Mach 9.7 flight condition. The phenomenon of radical-farming has been studied in detail using two-dimensional OH* chemiluminescence imaging and emission spectroscopy. High signal levels of excited OH (OH*) were detected behind the first shock reflections inside the combustion chamber upstream of any measurable pressure rise from combustion, which occurred towards the rear of the combustor. The production of OH in the first hot pocket initiates the ignition process and then accelerates the combustion process in the next downstream hot pocket. This was confirmed by numerical simulations of premixed hydrogen/air flow through the scramjet. Chemical kinetics analyses reveal that the ignition process is governed by the interaction between various reaction groups leading to a chainbranching explosion for low mean temperature and pressure combustion flowfields.

In-situ combustion synthesis of ultrafine TiB2 particles reinforced Cu matrix composite

Due to the lower strength of pure copper (Cu), ceramic particulate or whisker reinforced Cu matrix composites have attracted wide interest in recent years [1–3]. These materials exhibit a combination of excellent thermal and electrical conductivities, high strength retention at elevated temperatures, and high microstructural stability [3]. The potential applications include various electrodes, electrical switches, and X-ray tube components [4].

Simulation-based fully Bayesian experimental design for mixed effects models

In this paper, we present fully Bayesian experimental designs for nonlinear mixed effects models, in which we develop simulation-based optimal design methods to search over both continuous and discrete design spaces. Although Bayesian inference has commonly been performed on nonlinear mixed effects models, there is a lack of research into performing Bayesian optimal design for nonlinear mixed effects models that require searches to be performed over several design variables. This is likely due to the fact that it is much more computationally intensive to perform optimal experimental design for nonlinear mixed effects models than it is to perform inference in the Bayesian framework. In this paper, the design problem is to determine the optimal number of subjects and samples per subject, as well as the (near) optimal urine sampling times for a population pharmacokinetic study in horses, so that the population pharmacokinetic parameters can be precisely estimated, subject to cost constraints. The optimal sampling strategies, in terms of the number of subjects and the number of samples per subject, were found to be substantially different between the examples considered in this work, which highlights the fact that the designs are rather problem-dependent and require optimisation using the methods presented in this paper.

Designing mixed species tree plantations for the tropics : balancing ecological attributes of species with landholder preferences in the Philippines

A mixed species reforestation program known as the Rainforestation Farming system was undertaken in the Philippines to develop forms of farm forestry more suitable for smallholders than the simple monocultural plantations commonly used then. In this study, we describe the subsequent changes in stand structure and floristic composition of these plantations in order to learn from the experience and develop improved prescriptions for reforestation systems likely to be attractive to smallholders. We investigated stands aged from 6 to 11 years old on three successive occasions over a 6 year period. We found the number of species originally present in the plots as trees >5 cm dbh decreased from an initial total of 76 species to 65 species at the end of study period. But, at the same time, some new species reached the size class threshold and were recruited into the canopy layer. There was a substantial decline in tree density from an estimated stocking of about 5000 trees per ha at the time of planting to 1380 trees per ha at the time of the first measurement; the density declined by a further 4.9% per year. Changes in composition and stand structure were indicated by a marked shift in the Importance Value Index of species. Over six years, shade-intolerant species became less important and the native shade-tolerant species (often Dipterocarps) increased in importance. Based on how the Rainforestation Farming plantations developed in these early years, we suggest that mixed-species plantations elsewhere in the humid tropics should be around 1000 trees per ha or less, that the proportion of fast growing (and hence early maturing) trees should be about 30–40% of this initial density and that any fruit tree component should only be planted on the plantation margin where more light and space are available for crowns to develop.

The analysis of large scale data taken from the world groundnut (Arachis hypogaea L.) germplasm collection. II. Two-way data with mixed data types

As a sequel to a paper that dealt with the analysis of two-way quantitative data in large germplasm collections, this paper presents analytical methods appropriate for two-way data matrices consisting of mixed data types, namely, ordered multicategory and quantitative data types. While various pattern analysis techniques have been identified as suitable for analysis of the mixed data types which occur in germplasm collections, the clustering and ordination methods used often can not deal explicitly with the computational consequences of large data sets (i.e. greater than 5000 accessions) with incomplete information. However, it is shown that the ordination technique of principal component analysis and the mixture maximum likelihood method of clustering can be employed to achieve such analyses. Germplasm evaluation data for 11436 accessions of groundnut (Arachis hypogaea L.) from the International Research Institute of the Semi-Arid Tropics, Andhra Pradesh, India were examined. Data for nine quantitative descriptors measured in the post-rainy season and five ordered multicategory descriptors were used. Pattern analysis results generally indicated that the accessions could be distinguished into four regions along the continuum of growth habit (or plant erectness). Interpretation of accession membership in these regions was found to be consistent with taxonomic information, such as subspecies. Each growth habit region contained accessions from three of the most common groundnut botanical varieties. This implies that within each of the habit types there is the full range of expression for the other descriptors used in the analysis. Using these types of insights, the patterns of variability in germplasm collections can provide scientists with valuable information for their plant improvement programs.

Mixed data types and the use of pattern analysis on the Australian groundnut germplasm data

Data in germplasm collections contain a mixture of data types; binary, multistate and quantitative. Given the multivariate nature of these data, the pattern analysis methods of classification and ordination have been identified as suitable techniques for statistically evaluating the available diversity. The proximity (or resemblance) measure, which is in part the basis of the complementary nature of classification and ordination techniques, is often specific to particular data types. The use of a combined resemblance matrix has an advantage over data type specific proximity measures. This measure accommodates the different data types without manipulating them to be of a specific type. Descriptors are partitioned into their data types and an appropriate proximity measure is used on each. The separate proximity matrices, after range standardisation, are added as a weighted average and the combined resemblance matrix is then used for classification and ordination. Germplasm evaluation data for 831 accessions of groundnut (Arachis hypogaea L.) from the Australian Tropical Field Crops Genetic Resource Centre, Biloela, Queensland were examined. Data for four binary, five ordered multistate and seven quantitative descriptors have been documented. The interpretative value of different weightings - equal and unequal weighting of data types to obtain a combined resemblance matrix - was investigated by using principal co-ordinate analysis (ordination) and hierarchical cluster analysis. Equal weighting of data types was found to be more valuable for these data as the results provided a greater insight into the patterns of variability available in the Australian groundnut germplasm collection. The complementary nature of pattern analysis techniques enables plant breeders to identify relevant accessions in relation to the descriptors which distinguish amongst them. This additional information may provide plant breeders with a more defined entry point into the germplasm collection for identifying sources of variability for their plant improvement program, thus improving the utilisation of germplasm resources.

Improving combustion stability in sugar factory boilers

Reliable operation of a sugar factory boiler station is essential for efficient and timely processing of the cane supply. Sugar factory boilers have to contend with changes in fuel quality caused by variations in performance of the extraction station, different cane varieties and associated agronomic factors along with fluctuations in factory steam demand. These variations can affect the stability of combustion in boiler furnaces leading to reductions in boiler steam output and large furnace pressure fluctuations that can cause serious damage. This paper investigates the causes of unstable combustion, discusses aspects of boiler design that make a boiler more susceptible to unstable combustion and uses modelling to evaluate different options for improving combustion stability.