Influência da adição de cálcio nas propriedades de pastas geopoliméricas destinadas a cimentação de poços de petróleo

Nowadays, the search for new technologies that are able to follow the upcoming challenges in oil industry is a constant. Always trying properties improvements of the used materials, looking for the best performance and greater life time. Besides the search for technologies that show an improvement of performance, the search for materials environmentally correct along the whole production process. In Oil well cementing, this search for new technologies passes through the development of slurry systems that support these requests and that are also environmentally friendly. In this context, the use of geopolymer slurries is a great alternative route to cementing oil wells. Besides having good properties, comparable to Portland cement slurries, this alternative material releases much less CO2 gas in the production of their root materials when compared the production of Portland cement, which releases tons of CO2. In order to improve the properties of geopolymer slurries has been added Calcium Oxide, as observed in other studies that slurries where the Calcium is present the values of compressive strength is greater. The addition has been realized based in the CaO/SiO2 molar ratio of 0.05, 0.10 and 0.15. Have been performed compressive strength tests, thickening time, rheology and fliud loss control test of the slurries, following NBR 9831, as well as the physical chemical characterization of XRD, SEM and TG. Has been observed in most of the tests the slurries follow a tendency until the ratio of 0.10, which inverses in the ratio 0.15. This behavior can be explained by two phenomena that occur simultaneously, the first one is the break of the polymer chains and a consequent increase in molucules mobility, which prevails until the ratio of 0.1, and the second is possible approach of the chains due to the capacity of the calcium ions stabilize the charges of two different aluminum. There is only one linearity in the mechanical behavior that can be attributed to the appereance of the C-S-H phase. Based on this, it is concluded that the phenomenon of breaking the polymer chains predominates until the ratio of 0.1, causing an increase of the filtrate volume, lower rheological parameters and increasing thickening time. From the ratio of 0.15 the approach of the chains predominates, and the behavior is reversed

Decomposição e liberação de nitrogênio de resíduos culturais de plantas de cobertura em um solo de cerrado

A produção de massa seca, a taxa de decomposição e a liberação de nitrogênio (N) foram avaliadas em um experimento com sete tipos de cobertura vegetal: milheto pérola (Pennisetum americanum sin. tiphoydes), braquiária (Brachiaria brizantha), sorgo forrageiro (Sorghum bicolor L. Moench), guandu (Cajanus cajan (L.) Millsp), crotalária juncea (Crotalarea juncea) e aveia-preta (Avena strigosa Schreb), em pousio e em área de cultivo convencional (testemunha), em solo de cerrado, em Uberaba, região do Triângulo Mineiro. Dentre as coberturas avaliadas, o milheto e a crotalária foram as que apresentaram a maior produção de massa seca, maior acúmulo e a maior liberação de N. A braquiária foi a cobertura que apresentou a maior taxa de decomposição. Todas as coberturas apresentaram a maior taxa de liberação de N até 42 dias após dessecação.

Ressignificação existencial do pretérito e longevidade humana

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Theoretical study of omeprazole behavior: Racemization barrier and decomposition reaction

omeprazole is a substituted benzimidazole which suppresses gastric-acid secretion by means of H+, K+-ATPase inhibition. It is an optically active drug with the sulfur of the sulfoxide being the chiral center. This pro-drug can be easily converted into its respective sulfenamide at low pH. In this work, omeprazole has been studied in relation to racemization barrier and decomposition reaction. Quantum chemistry coupled to PCA chemometric method were used to find all minimum energy structures. Conformational analysis and calculation of racemization barriers were carried out by PM3 semiempirical method (Gaussian 98). The average racemization energy barrier for all minimum energy structures (43.56 kcal mol(-1)) can be related to the velocity constant in Eyring's equation. The enormous half-life time at 100 degrees C (9.04 x 10(4) years) indicates that the process cannot be observed in human time scale. on the other hand, the difference of free energy change (Delta(Delta G) = -266.78 kcal mol(-1)) for the decomposition reaction shows that the process is favorable to the sulfenamide formation. The highly negative Delta(Delta G) obtained for the decomposition reaction shows that this process is extremely exothermic. This result explains why omeprazole decomposes and does not racemize. (C) 2008 Wiley Periodicals, Inc.

Perfil espacial e temporal de poluentes nas águas da represa municipal de São José do Rio Preto, São Paulo, Brasil

In this manuscript, seasonal and spatial trends of water collected from two sampling places in the Preto River in the Turvo-Grande watershed were evaluated. Water samples were collected during June/07 to July/08 and parameters sulphate, total organic carbon, ammonia, conductivity, dissolved oxygen, temperature, dissolved total solids and nitrate were quantified. Seasonal trend indicated sanitary effluents as a point source of contamination in both sampling points. Vertical trends demonstrated that the Municipal Dam was not stratified and received a diffuse source of pollutants from flooding and agriculture runoffs. It was also verified that there is relatively fast ammonia consumption kinetics having a half-life time of 1.43 h which can explain the low ammonia concentrations found in these aquatic bodies.

Erbium and ytterbium co-doped SiO2 : GeO2 planar waveguide prepared by the sol-gel route using an alternative precursor

The sol-gel method combined with a spin-coating technique has been successfully applied for the preparation of rare-earth doped silica:germania films used for the fabrication of erbium-doped waveguide amplifiers (EDWA), presenting several advantages over other methods for the preparation of thin films. As with other methods, the sol-gel route also shows some drawbacks, such as cracks related to the thickness of silica films and high hydrolysis rate of certain precursors such as germanium alkoxides. This article describes the preparation and optical characterization of erbium and ytterbium co-doped SiO2:GeO2 crack-free thick films prepared by the sol-gel route combined with a spin-coating technique using a chemically stable non-aqueous germanium oxide solution as an alternative precursor. The non-crystalline films obtained are planar waveguides exhibiting a single mode at 1,550 nm with an average thickness of 3.9 mu m presenting low percentages of porosity evaluated by the Lorentz-Lorenz Effective Medium Approximation, and low stress, according to the refractive index values measured in both transversal electric and magnetic polarizations. Weakly confining core layers (0.3% < Delta n < 0.75%) were obtained according to the refractive index difference between the core and buffer layers, suggesting that low-loss coupling EDWA may be obtained. The life time of the erbium I-4(13/2) metastable state was measured as a function of erbium concentration in different systems and based on these values it is possible to infer that the hydroxyl group was reduced and the formation of rare-earth clusters was avoided.

Pressure field along the axis of a high-power klystron amplifier

The pressure field in a high-power klystron amplifier is investigated to scale the ionic vacuum pump used to maintain the ultra high-vacuum in the device in order to increase its life-time. The investigation is conducted using an 1.3 GHz, 100 A - 240 keV high-power klystron with five reentrant coaxial cavities, assembled in a cylindrical drift tube 1.2 m long. The diffusion equation is solved to the regime molecular flow to obtain the pressure profile along the axis of the klystron drift tube. The model, solved by both analytical and numerical procedures, is able to determine the pressure values in steady-state case. This work considers the specific conductance and all important gas sources, as in the degassing of the drift tube and cavities walls, cathode, and collector. For the drift tube degassing rate equals to q(deg) = 2x10(-12) (-)mbar.L.s(-1) cm(-2) (degassing rate per unit area), to cavities q(cavity) = 3x10(-13) mbar.L.s(-1)cm(-2), to the cathode q(cathode) = 6x10(-9)_mbar.L.s(-1) and to the collector q(collector) = 6x10(-9) mbar.L.s(-1), it was found that a 10 L.s(-1) ionic vacuum pump connected in the output waveguide wall is suitable. In this case, the pressure obtained in the cathode is p(cathode) = 6.3x10(-9) mbar, in the collector p(collector) = 2.7x10(-9) mbar, and in the output waveguide p = 2.1x10(-9) mbar. Although only the steady-state case is analyzed, some aspects that may be relevant in a transient situation, for instance, when the beam hits the drift tube walls, producing a gas burst, is also commented.

Microstructure and corrosion resistance of inorganic-organic (ZrO2-PMMA) hybrid coating on stainless steel

Zirconia-polymethylmetacrylate hybrids prepared by a sol-gel method were deposited by dip-coating on stainless steel to improve the resistance against wet corrosion. The effect of the concentration of polymethylmetacrylate and the number of coating applications on the microstructure and corrosion performance of coated samples was investigated. The microstructural properties of samples was analyzed by scanning electron and atomic force microscopy, adhesion tests and profilemeter measurements. The electrochemical corrosion was evaluated through potentiodynamic polarization curves at room temperature. Results show that the sample prepared with 17 vol.% of polymethylmethacrylate has a maximum corrosion resistance, smaller roughness, are hermetic and adherent to the substrate. This film increases the life time of the stainless steel by a factor 30. (C) 1999 Elsevier B.V. B.V. All rights reserved.

Cluster identification and characterization in the riser of a circulating fluidized bed from numerical simulation results

A methodology of identification and characterization of coherent structures mostly known as clusters is applied to hydrodynamic results of numerical simulation generated for the riser of a circulating fluidized bed. The numerical simulation is performed using the MICEFLOW code, which includes the two-fluids IIT's hydrodynamic model B. The methodology for cluster characterization that is used is based in the determination of four characteristics, related to average life time, average volumetric fraction of solid, existing time fraction and frequency of occurrence. The identification of clusters is performed by applying a criterion related to the time average value of the volumetric solid fraction. A qualitative rather than quantitative analysis is performed mainly owing to the unavailability of operational data used in the considered experiments. Concerning qualitative analysis, the simulation results are in good agreement with literature. Some quantitative comparisons between predictions and experiment were also presented to emphasize the capability of the modeling procedure regarding the analysis of macroscopic scale coherent structures. (c) 2007 Elsevier B.V. All rights reserved.

Cigarette smoking and high-risk HPV DNA as predisposing factors for high-grade cervical intraepithelial neoplasia (CIN) in young Brazilian women

Background. This cross-sectional study was designed to evaluate the role of cigarette smoking and high-risk HPV types as risk factors of CIN 2 and 3 in young, sexually active Brazilian women. Materials and method. A series of 100 consecutive women with abnormal Pap smears were recruited, subjected to colposcopy, punch biopsy, and questionnaire for their social, sexual and reproductive factors. Of these, 77 women between 20 and 35 years of age (median 26.5 years) with biopsy-confirmed CIN 1 or CIN 2 and 3, were enrolled in this study. Representative samples from the exocervix and endocervix were obtained for HPV testing with the Hybrid Capture HPV-DNA assay, including the probes for the oncogenic HPV types (16, 18, 31, 33, 35, 45, 51, 52 and 56). Results. The overall rate of CIN 2 and 3 was 23/77 (29.8%). The women with CIN 1, 2 and 3 did not differ from each other with regard to their age, race, schooling, marital status, life-time number of sexual partners, age at first intercourse, use of oral contraceptives, or parity. However, current cigarette smoking was strongly associated with CIN 2 and 3 (p < 0,001), and among smokers, the risk of high-grade CIN increased in parallel with the time of exposure (years of smoking) p = 0.07), HPV-DNA of the oncogenic types was detected in 43 (56%) women, the risk of being HPV DNA-positive was significantly higher in CIN 2 and 3 as compared with CIN 1 (p = 0.037). Importantly, the prevalence of high-risk HPV types was significantly higher in cigarette smokers than in non-smokers (p = 0.046). Conclusions. The results indicate that the severity of CIN lesions was clearly related to two fundamental risk factors: 1) high-risk HPV types, and 2) current cigarette smoking. These two risk factors were closely interrelated in that the high-risk HPV types were significantly more frequent in current smokers than in non-smokers, suggesting the possibility of a synergistic action between these two risk factors in cervical carcinogenesis.

Neutrinoless double beta decay with and without Majoron-like boson emission in a 3-3-1 model

We consider the contributions to the neutrinoless double beta decays in a SU(3)L⊗U(1)N electroweak model. We show that for a range of parameters in the model there are diagrams involving vector-vector-scalar and trilinear scalar couplings which can be potentially as contributing as the light massive Majorana neutrino exchange one. We use these contributions to obtain constraints upon some mass scales of the model, such as the masses of the new charged vector and scalar bosons. We also consider briefly the decay in which, in addition to the two electrons, a Majoron-like boson is emitted. ©2001 The American Physical Society.

Kaposi's sarcoma-associated herpesvirus latency-associated nuclear antigen 1 mimics Epstein-Barr virus EBNA1 immune evasion through central repeat domain effects on protein processing

Kaposi's sarcoma-associated herpesvirus (KSHV/human herpesvirus 8 [HHV8]) and Epstein-Barr virus (EBV/HHV4) are distantly related gammaherpesviruses causing tumors in humans. KSHV latency-associated nuclear antigen 1 (LANA1) is functionally similar to the EBV nuclear antigen-1 (EBNA1) protein expressed during viral latency, although they have no amino acid similarities. EBNA1 escapes cytotoxic lymphocyte (CTL) antigen processing by inhibiting its own proteosomal degradation and retarding its own synthesis to reduce defective ribosomal product processing. We show here that the LANA1 QED-rich central repeat (CR) region, particularly the CR2CR3 subdomain, also retards LANA1 synthesis and markedly enhances LANA1 stability in vitro and in vivo. LANA1 isoforms have half-lives greater than 24 h, and fusion of the LANA1 CR2CR3 domain to a destabilized heterologous protein markedly decreases protein turnover. Unlike EBNA1, the LANA1 CR2CR3 subdomain retards translation regardless of whether it is fused to the 5′ or 3′ end of a heterologous gene construct. Manipulation of sequence order, orientation, and composition of the CR2 and CR3 subdomains suggests that specific peptide sequences rather than RNA structures are responsible for synthesis retardation. Although mechanistic differences exist between LANA1 and EBNA1, the primary structures of both proteins have evolved to minimize provoking CTL immune responses. Simple strategies to eliminate these viral inhibitory regions may markedly improve vaccine effectiveness by maximizing CTL responses. Copyright © 2007, American Society for Microbiology. All Rights Reserved.

The Poisson-exponential lifetime distribution

In this paper we proposed a new two-parameters lifetime distribution with increasing failure rate. The new distribution arises on a latent complementary risk problem base. The properties of the proposed distribution are discussed, including a formal proof of its probability density function and explicit algebraic formulae for its reliability and failure rate functions, quantiles and moments, including the mean and variance. A simple EM-type algorithm for iteratively computing maximum likelihood estimates is presented. The Fisher information matrix is derived analytically in order to obtaining the asymptotic covariance matrix. The methodology is illustrated on a real data set. © 2010 Elsevier B.V. All rights reserved.

Morfogênese e dinâmica do perfilhamento do capim-marandu submetido à alturas de pastejo em lotação contínua com e sem suplementação

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Aspectos psicológicos do adolescer com HIV/Aids: estudo de caso

Pós-graduação em Psicologia - FCLAS