Adaptive cross-device videoconferencing solution for wireless networks based on QoS monitoring

The increase in CPU power and screen quality of todays smartphones as well as the availability of high bandwidth wireless networks has enabled high quality mobile videoconfer- encing never seen before. However, adapting to the variety of devices and network conditions that come as a result is still not a trivial issue. In this paper, we present a multiple participant videoconferencing service that adapts to different kind of devices and access networks while providing an stable communication. By combining network quality detection and the use of a multipoint control unit for video mixing and transcoding, desktop, tablet and mobile clients can participate seamlessly. We also describe the cost in terms of bandwidth and CPU usage of this approach in a variety of scenarios.

Processing of ultra-wideband low-frequency signals, for application in Foliage Penetration (FOPEN) Synthetic Aperture Radar (SAR) systems

Foliage Penetration (FOPEN) radar systems were introduced in 1960, and have been constantly improved by several organizations since that time. The use of Synthetic Aperture Radar (SAR) approaches for this application has important advantages, due to the need for high resolution in two dimensions. The design of this type of systems, however, includes some complications that are not present in standard SAR systems. FOPEN SAR systems need to operate with a low central frequency (VHF or UHF bands) in order to be able to penetrate the foliage. High bandwidth is also required to obtain high resolution. Due to the low central frequency, large integration angles are required during SAR image formation, and therefore the Range Migration Algorithm (RMA) is used. This project thesis identifies the three main complications that arise due to these requirements. First, a high fractional bandwidth makes narrowband propagation models no longer valid. Second, the VHF and UHF bands are used by many communications systems. The transmitted signal spectrum needs to be notched to avoid interfering them. Third, those communications systems cause Radio Frequency Interference (RFI) on the received signal. The thesis carries out a thorough analysis of the three problems, their degrading effects and possible solutions to compensate them. The UWB model is applied to the SAR signal, and the degradation induced by it is derived. The result is tested through simulation of both a single pulse stretch processor and the complete RMA image formation. Both methods show that the degradation is negligible, and therefore the UWB propagation effect does not need compensation. A technique is derived to design a notched transmitted signal. Then, its effect on the SAR image formation is evaluated analytically. It is shown that the stretch processor introduces a processing gain that reduces the degrading effects of the notches. The remaining degrading effect after processing gain is assessed through simulation, and an experimental graph of degradation as a function of percentage of nulled frequencies is obtained. The RFI is characterized and its effect on the SAR processor is derived. Once again, a processing gain is found to be introduced by the receiver. As the RFI power can be much higher than that of the desired signal, an algorithm is proposed to remove the RFI from the received signal before RMA processing. This algorithm is a modification of the Chirp Least Squares Algorithm (CLSA) explained in [4], which adapts it to deramped signals. The algorithm is derived analytically and then its performance is evaluated through simulation, showing that it is effective in removing the RFI and reducing the degradation caused by both RFI and notching. Finally, conclusions are drawn as to the importance of each one of the problems in SAR system design.

Diseño de una red de acceso mediante fibra óptica

Con el objetivo de consolidar los conocimientos en Sistemas de Telecomunicación, se pretende diseñar una red para la distribución de servicios avanzados, como televisión, internet de banda ancha y telefonía, mediante el uso de la tecnología FTTH. La red será totalmente pasiva, óptica, y de gran ancho de banda, Tipo PON (Passive Optical Network), de manera que el haz de luz del emisor se distribuye hacia múltiples fibras siguiendo diferentes direcciones, o las confina en el sentido opuesto usando técnicas WDM y TDMA. En primer lugar, es preciso realizar un estudio teórico sobre las características de la fibra óptica, junto con las propiedades de los elementos activos y pasivos que interactúan con ella, para poder comprender la tecnología en la que se basa y así ofrecer una solución final acorde a las necesidades que se presenten. Tras un vistazo general a la tecnología de fibra óptica, se procede a estudiar las características y topologías de las redes de acceso basadas en la misma, junto con los requisitos de cara al diseño de la redes y a la gestión de proyectos. Se definirán los objetivos de la red, ya que la complejidad de la red depende de factores como la extensión y cobertura de la misma, o el ancho de banda. Posteriormente se irá diseñando la red en una arquitectura descendente hasta destinar una única fibra óptica para cada hogar dentro de la cobertura de la red. Se detallarán todas las especificaciones necesarias para definir la red, (potencias, modulaciones y tipos de fibra) así como el instrumental y demás medios necesarios para operar con la misma. Aunque el diseño de una red FTTH contempla muchos más aspectos de los estudiados en el presente proyecto, se tomó como objetivo el diseño y planificación correspondientes a una sección de un área de escasa población donde la instalación se tomó como viable, obviando así pequeños detalles y centrándose en el despliegue de fibra óptica. Se pretende así ofrecer una solución de infraestructura doméstica de telecomunicaciones, apta para las futuras necesidades que implican la creciente demanda de servicios como internet de banda ancha o almacenamiento y procesado de aplicaciones en nube. La fibra óptica tiene mucho que ofrecer a las telecomunicaciones, y cada vez es más frecuente encontrar redes de fibra óptica como parte de un servicio de telecomunicaciones, tanto como para particulares como empresas. ABSTRACT. Aiming to strengthen knowledge in Telecommunications Systems, is intended to design a network for advanced services broadcasting, including digital TV, broadband internet and telephony, by using FTTH technology. This network will be entirely passive optic, and high bandwidth, PON type (Passive Optical Network) so that the transmitter beam is broadcasting to multiple optical fibers, branching out in different ways or joining them in the opposite. First, it is necessary to perform a theoretical study on the characteristics of the optical fiber, along with the properties of the active and passive elements that interact with it, to understand the technology that is based and offer a final solution according needs that arise. After an overview of the optical fiber technology, we proceed to study the characteristics and topologies access networks based on that, together with the requirements to face the network design and project management. System objectives will be determined, since the complexity of the network depends on factors such as the size and scope of it, or bandwidth. Later, the network will be designing in downstream architecture to deliver a single optical fiber to each household within the network area. All necessary specifications to define the network (power, modulation and fiber types) will be determined, as instruments and other means to operate it. Although FTTH network design includes many more aspects of those studied in this project, it was taken as objective the network design and planning corresponding to a section of a sparsely populated area where the facility was taken as feasible thus obviating small details and focus on the deployment of optical fiber. This is intended to provide a solution of household telecommunications infrastructure suitable for future needs involving the growing demand for services such as broadband internet or processing storage and cloud applications. The optical fiber has much to offer to telecommunications, and it is increasingly common to find fiber optic networks as part of a telecommunications service, both to individuals and businesses.

Despliegue de la tecnología de fibra óptica hasta la vivienda

El presente Proyecto Fin de Grado, expone un estudio detallado del despliegue de una red FTTH para una determinada zona de viviendas. En él se podrá observar paso a paso los elementos que forman parte de las redes G-PON y las técnicas utilizadas para calcular las necesidades de cada vivienda. Este tipo de redes permite el despliegue de fibra óptica desde la central hasta la propia vivienda del abonado. La fibra óptica es el medio de transmisión de información que ofrece mejores prestaciones en cuanto a velocidad de transmisión y distancia, permitiendo ofrecer servicios que requieren de un gran ancho de banda. De esta manera, la tecnología FTTH se sitúa a la cabeza en cuanto a prestaciones frente a otras tecnologías. El principal objetivo de este despliegue es analizar el recorrido que lleva la fibra hasta llegar a la vivienda del abonado, para ello se explicará los elementos por los que pasa, los materiales y equipos que deben instalarse, las canalizaciones a utilizar y el diseño final del trazado de la fibra por las diferentes viviendas a las que queremos dar servicio. Este documento se organiza en distintos capítulos. Comienza con un capítulo donde se explican los principales objetivos de este proyecto. En el segundo capítulo se explicará la arquitectura y las principales características de las redes FTTH. En el tercer capítulo se explicaran los criterios, estructura y elementos que compone una red FTTH desde que sale de la central hasta que llega a la vivienda. Y por último, se realizará un caso práctico y real del recorrido de la fibra con sus correspondientes planos. ABSTRACT. The present Final Degree Project expounds a detailed study for the deployment of an FTTH network, for a particular housing area. We will see step by step the elements that are part of the G-PON and the techniques used to calculate the needs of each place. FTTH networks allow the deployment of optical fiber from the central office to the subcriber´s home. The optical fiber is the medium of transmission that offers the best performance in terms of speed and distance, allowing us to offer services that require high bandwidth. So, the FTTH technology takes the lead in performance over other technologies. The main objective of this deployment is to analyse the itinerary of the fiber optic to arrive to the house of the client, in order to this, it will be explained the parts that are crossed by the fiber optic, the materials and equipments that have to be instaled, the scorings and the final design of the route of the fiber optic around the houses. This document is divided in different chapters. In the first one it is explained the main objectives of this project and in the second one the architecture and main characteristics of FTTH networks. In the third chapter are described the rules, structures and elements that composed this network in order to arrive to houses. Finally, I will exemplify the previous theory with a practical case, with a real route with its plans.

Examining TCP parallelization related methods for various packet losses

The diversity of the networks (wired/wireless) prefers a TCP solution robust across a wide range of networks rather than fine-tuned for a particular one at the cost of another. TCP parallelization uses multiple virtual TCP connections to transfer data for an application process and opens a way to improve TCP performance across a wide range of environments - high bandwidth-delay product (BDP), wireless as well as conventional networks. In particular, it can significantly benefit the emerging high-speed wireless networks. Despite its potential to work well over a wide range of networks, it is not fully understood how TCP parallelization performs when experiencing various packet losses in the heterogeneous environment. This paper examines the current TCP parallelization related methods under various packet losses and shows how to improve the performance of TCP parallelization.

Performance analysis of multi-radio AODV in hybrid wireless mesh networks

Wireless Mesh Networks (WMNs), based on commodity hardware, present a promising technology for a wide range of applications due to their self-configuring and self-healing capabilities, as well as their low equipment and deployment costs. One of the key challenges that WMN technology faces is the limited capacity and scalability due to co-channel interference, which is typical for multi-hop wireless networks. A simple and relatively low-cost approach to address this problem is the use of multiple wireless network interfaces (radios) per node. Operating the radios on distinct orthogonal channels permits effective use of the frequency spectrum, thereby, reducing interference and contention. In this paper, we evaluate the performance of the multi-radio Ad-hoc On-demand Distance Vector (AODV) routing protocol with a specific focus on hybrid WMNs. Our simulation results show that under high mobility and traffic load conditions, multi-radio AODV offers superior performance as compared to its single-radio counterpart. We believe that multi-radio AODV is a promising candidate for WMNs, which need to service a large number of mobile clients with low latency and high bandwidth requirements.

Superstring: A scalable service discovery protocol for the wide-area pervasive environment

Arguably, the world has become one large pervasive computing environment. Our planet is growing a digital skin of a wide array of sensors, hand-held computers, mobile phones, laptops, web services and publicly accessible web-cams. Often, these devices and services are deployed in groups, forming small communities of interacting devices. Service discovery protocols allow processes executing on each device to discover services offered by other devices within the community. These communities can be linked together to form a wide-area pervasive environment, allowing processes in one p u p tu interact with services in another. However, the costs of communication and the protocols by which this communication is mediated in the wide-area differ from those of intra-group, or local-area, communication. Communication is an expensive operation for small, battery powered devices, but it is less expensive for servem and workstations, which have a constant power supply and 81'e connected to high bandwidth networks. This paper introduces Superstring, a peer to-peer service discovery protocol optimised fur use in the wide-area. Its goals are to minimise computation and memory overhead in the face of large numbers of resources. It achieves this memory and computation scalability by distributing the storage cost of service descriptions and the computation cost of queries over multiple resolvers.

A thermally wavelength-tunable photonic switch based on silicon microring resonator

Silicon photonics is a very promising technology for future low-cost high-bandwidth optical telecommunication applications down to the chip level. This is due to the high degree of integration, high optical bandwidth and large speed coupled with the development of a wide range of integrated optical functions. Silicon-based microring resonators are a key building block that can be used to realize many optical functions such as switching, multiplexing, demultiplaxing and detection of optical wave. The ability to tune the resonances of the microring resonators is highly desirable in many of their applications. In this work, the study and application of a thermally wavelength-tunable photonic switch based on silicon microring resonator is presented. Devices with 10μm diameter were systematically studied and used in the design. Its resonance wavelength was tuned by thermally induced refractive index change using a designed local micro-heater. While thermo-optic tuning has moderate speed compared with electro-optic and all-optic tuning, with silicon’s high thermo-optic coefficient, a much wider wavelength tunable range can be realized. The device design was verified and optimized by optical and thermal simulations. The fabrication and characterization of the device was also implemented. The microring resonator has a measured FSR of ∼18 nm, FWHM in the range 0.1-0.2 nm and Q around 10,000. A wide tunable range (>6.4 nm) was achieved with the switch, which enables dense wavelength division multiplexing (DWDM) with a channel space of 0.2nm. The time response of the switch was tested on the order of 10 μs with a low power consumption of ∼11.9mW/nm. The measured results are in agreement with the simulations. Important applications using the tunable photonic switch were demonstrated in this work. 1×4 and 4×4 reconfigurable photonic switch were implemented by using multiple switches with a common bus waveguide. The results suggest the feasibility of on-chip DWDM for the development of large-scale integrated photonics. Using the tunable switch for output wavelength control, a fiber laser was demonstrated with Erbium-doped fiber amplifier as the gain media. For the first time, this approach integrated on-chip silicon photonic wavelength control.

Digital surveillance based on video CODEC System-on-a-Chip (SoC) platforms

Today, most conventional surveillance networks are based on analog system, which has a lot of constraints like manpower and high-bandwidth requirements. It becomes the barrier for today's surveillance network development. This dissertation describes a digital surveillance network architecture based on the H.264 coding/decoding (CODEC) System-on-a-Chip (SoC) platform. The proposed digital surveillance network architecture includes three major layers: software layer, hardware layer, and the network layer. The following outlines the contributions to the proposed digital surveillance network architecture. (1) We implement an object recognition system and an object categorization system on the software layer by applying several Digital Image Processing (DIP) algorithms. (2) For better compression ratio and higher video quality transfer, we implement two new modules on the hardware layer of the H.264 CODEC core, i.e., the background elimination module and the Directional Discrete Cosine Transform (DDCT) module. (3) Furthermore, we introduce a Digital Signal Processor (DSP) sub-system on the main bus of H.264 SoC platforms as the major hardware support system for our software architecture. Thus we combine the software and hardware platforms to be an intelligent surveillance node. Lab results show that the proposed surveillance node can dramatically save the network resources like bandwidth and storage capacity.

Monetary cost -efficient query distribution in ISDN -connected heterogeneous databases

Current technology permits connecting local networks via high-bandwidth telephone lines. Central coordinator nodes may use Intelligent Networks to manage data flow over dialed data lines, e.g. ISDN, and to establish connections between LANs. This dissertation focuses on cost minimization and on establishing operational policies for query distribution over heterogeneous, geographically distributed databases. Based on our study of query distribution strategies, public network tariff policies, and database interface standards we propose methods for communication cost estimation, strategies for the reduction of bandwidth allocation, and guidelines for central to node communication protocols. Our conclusion is that dialed data lines offer a cost effective alternative for the implementation of distributed database query systems, and that existing commercial software may be adapted to support query processing in heterogeneous distributed database systems. ^

Two-Path All-pass Based Half-Band Infinite Impulse Response Decimation Filters and the Effects of Their Non-Linear Phase Response on ECG Signal Acquisition

This paper is based on the novel use of a very high fidelity decimation filter chain for Electrocardiogram (ECG) signal acquisition and data conversion. The multiplier-free and multi-stage structure of the proposed filters lower the power dissipation while minimizing the circuit area which are crucial design constraints to the wireless noninvasive wearable health monitoring products due to the scarce operational resources in their electronic implementation. The decimation ratio of the presented filter is 128, working in tandem with a 1-bit 3rd order Sigma Delta (ΣΔ) modulator which achieves 0.04 dB passband ripples and -74 dB stopband attenuation. The work reported here investigates the non-linear phase effects of the proposed decimation filters on the ECG signal by carrying out a comparative study after phase correction. It concludes that the enhanced phase linearity is not crucial for ECG acquisition and data conversion applications since the signal distortion of the acquired signal, due to phase non-linearity, is insignificant for both original and phase compensated filters. To the best of the authors’ knowledge, being free of signal distortion is essential as this might lead to misdiagnosis as stated in the state of the art. This article demonstrates that with their minimal power consumption and minimal signal distortion features, the proposed decimation filters can effectively be employed in biosignal data processing units.

Error correcting codes for visible light communication systems

Over the past few years, the number of wireless networks users has been increasing. Until now, Radio-Frequency (RF) used to be the dominant technology. However, the electromagnetic spectrum in these region is being saturated, demanding for alternative wireless technologies. Recently, with the growing market of LED lighting, the Visible Light Communications has been drawing attentions from the research community. First, it is an eficient device for illumination. Second, because of its easy modulation and high bandwidth. Finally, it can combine illumination and communication in the same device, in other words, it allows to implement highly eficient wireless communication systems. One of the most important aspects in a communication system is its reliability when working in noisy channels. In these scenarios, the received data can be afected by errors. In order to proper system working, it is usually employed a Channel Encoder in the system. Its function is to code the data to be transmitted in order to increase system performance. It commonly uses ECC, which appends redundant information to the original data. At the receiver side, the redundant information is used to recover the erroneous data. This dissertation presents the implementation steps of a Channel Encoder for VLC. It was consider several techniques such as Reed-Solomon and Convolutional codes, Block and Convolutional Interleaving, CRC and Puncturing. A detailed analysis of each technique characteristics was made in order to choose the most appropriate ones. Simulink models were created in order to simulate how diferent codes behave in diferent scenarios. Later, the models were implemented in a FPGA and simulations were performed. Hardware co-simulations were also implemented to faster simulation results. At the end, diferent techniques were combined to create a complete Channel Encoder capable of detect and correct random and burst errors, due to the usage of a RS(255,213) code with a Block Interleaver. Furthermore, after the decoding process, the proposed system can identify uncorrectable errors in the decoded data due to the CRC-32 algorithm.

Architectural-Physical Co-Design of 3D CPUs with Micro-Fluidic Cooling

The performance, energy efficiency and cost improvements due to traditional technology scaling have begun to slow down and present diminishing returns. Underlying reasons for this trend include fundamental physical limits of transistor scaling, the growing significance of quantum effects as transistors shrink, and a growing mismatch between transistors and interconnects regarding size, speed and power. Continued Moore's Law scaling will not come from technology scaling alone, and must involve improvements to design tools and development of new disruptive technologies such as 3D integration. 3D integration presents potential improvements to interconnect power and delay by translating the routing problem into a third dimension, and facilitates transistor density scaling independent of technology node. Furthermore, 3D IC technology opens up a new architectural design space of heterogeneously-integrated high-bandwidth CPUs. Vertical integration promises to provide the CPU architectures of the future by integrating high performance processors with on-chip high-bandwidth memory systems and highly connected network-on-chip structures. Such techniques can overcome the well-known CPU performance bottlenecks referred to as memory and communication wall. However the promising improvements to performance and energy efficiency offered by 3D CPUs does not come without cost, both in the financial investments to develop the technology, and the increased complexity of design. Two main limitations to 3D IC technology have been heat removal and TSV reliability. Transistor stacking creates increases in power density, current density and thermal resistance in air cooled packages. Furthermore the technology introduces vertical through silicon vias (TSVs) that create new points of failure in the chip and require development of new BEOL technologies. Although these issues can be controlled to some extent using thermal-reliability aware physical and architectural 3D design techniques, high performance embedded cooling schemes, such as micro-fluidic (MF) cooling, are fundamentally necessary to unlock the true potential of 3D ICs. A new paradigm is being put forth which integrates the computational, electrical, physical, thermal and reliability views of a system. The unification of these diverse aspects of integrated circuits is called Co-Design. Independent design and optimization of each aspect leads to sub-optimal designs due to a lack of understanding of cross-domain interactions and their impacts on the feasibility region of the architectural design space. Co-Design enables optimization across layers with a multi-domain view and thus unlocks new high-performance and energy efficient configurations. Although the co-design paradigm is becoming increasingly necessary in all fields of IC design, it is even more critical in 3D ICs where, as we show, the inter-layer coupling and higher degree of connectivity between components exacerbates the interdependence between architectural parameters, physical design parameters and the multitude of metrics of interest to the designer (i.e. power, performance, temperature and reliability). In this dissertation we present a framework for multi-domain co-simulation and co-optimization of 3D CPU architectures with both air and MF cooling solutions. Finally we propose an approach for design space exploration and modeling within the new Co-Design paradigm, and discuss the possible avenues for improvement of this work in the future.

Physical Design Methodologies for Low Power and Reliable 3D ICs

As the semiconductor industry struggles to maintain its momentum down the path following the Moore's Law, three dimensional integrated circuit (3D IC) technology has emerged as a promising solution to achieve higher integration density, better performance, and lower power consumption. However, despite its significant improvement in electrical performance, 3D IC presents several serious physical design challenges. In this dissertation, we investigate physical design methodologies for 3D ICs with primary focus on two areas: low power 3D clock tree design, and reliability degradation modeling and management. Clock trees are essential parts for digital system which dissipate a large amount of power due to high capacitive loads. The majority of existing 3D clock tree designs focus on minimizing the total wire length, which produces sub-optimal results for power optimization. In this dissertation, we formulate a 3D clock tree design flow which directly optimizes for clock power. Besides, we also investigate the design methodology for clock gating a 3D clock tree, which uses shutdown gates to selectively turn off unnecessary clock activities. Different from the common assumption in 2D ICs that shutdown gates are cheap thus can be applied at every clock node, shutdown gates in 3D ICs introduce additional control TSVs, which compete with clock TSVs for placement resources. We explore the design methodologies to produce the optimal allocation and placement for clock and control TSVs so that the clock power is minimized. We show that the proposed synthesis flow saves significant clock power while accounting for available TSV placement area. Vertical integration also brings new reliability challenges including TSV's electromigration (EM) and several other reliability loss mechanisms caused by TSV-induced stress. These reliability loss models involve complex inter-dependencies between electrical and thermal conditions, which have not been investigated in the past. In this dissertation we set up an electrical/thermal/reliability co-simulation framework to capture the transient of reliability loss in 3D ICs. We further derive and validate an analytical reliability objective function that can be integrated into the 3D placement design flow. The reliability aware placement scheme enables co-design and co-optimization of both the electrical and reliability property, thus improves both the circuit's performance and its lifetime. Our electrical/reliability co-design scheme avoids unnecessary design cycles or application of ad-hoc fixes that lead to sub-optimal performance. Vertical integration also enables stacking DRAM on top of CPU, providing high bandwidth and short latency. However, non-uniform voltage fluctuation and local thermal hotspot in CPU layers are coupled into DRAM layers, causing a non-uniform bit-cell leakage (thereby bit flip) distribution. We propose a performance-power-resilience simulation framework to capture DRAM soft error in 3D multi-core CPU systems. In addition, a dynamic resilience management (DRM) scheme is investigated, which adaptively tunes CPU's operating points to adjust DRAM's voltage noise and thermal condition during runtime. The DRM uses dynamic frequency scaling to achieve a resilience borrow-in strategy, which effectively enhances DRAM's resilience without sacrificing performance. The proposed physical design methodologies should act as important building blocks for 3D ICs and push 3D ICs toward mainstream acceptance in the near future.

COMPRESSIVE QUANTIZATION FOR SCALABLE CLOUD RADIO ACCESS NETWORKS

With the proliferation of new mobile devices and applications, the demand for ubiquitous wireless services has increased dramatically in recent years. The explosive growth in the wireless traffic requires the wireless networks to be scalable so that they can be efficiently extended to meet the wireless communication demands. In a wireless network, the interference power typically grows with the number of devices without necessary coordination among them. On the other hand, large scale coordination is always difficult due to the low-bandwidth and high-latency interfaces between access points (APs) in traditional wireless networks. To address this challenge, cloud radio access network (C-RAN) has been proposed, where a pool of base band units (BBUs) are connected to the distributed remote radio heads (RRHs) via high bandwidth and low latency links (i.e., the front-haul) and are responsible for all the baseband processing. But the insufficient front-haul link capacity may limit the scale of C-RAN and prevent it from fully utilizing the benefits made possible by the centralized baseband processing. As a result, the front-haul link capacity becomes a bottleneck in the scalability of C-RAN. In this dissertation, we explore the scalable C-RAN in the effort of tackling this challenge. In the first aspect of this dissertation, we investigate the scalability issues in the existing wireless networks and propose a novel time-reversal (TR) based scalable wireless network in which the interference power is naturally mitigated by the focusing effects of TR communications without coordination among APs or terminal devices (TDs). Due to this nice feature, it is shown that the system can be easily extended to serve more TDs. Motivated by the nice properties of TR communications in providing scalable wireless networking solutions, in the second aspect of this dissertation, we apply the TR based communications to the C-RAN and discover the TR tunneling effects which alleviate the traffic load in the front-haul links caused by the increment of TDs. We further design waveforming schemes to optimize the downlink and uplink transmissions in the TR based C-RAN, which are shown to improve the downlink and uplink transmission accuracies. Consequently, the traffic load in the front-haul links is further alleviated by the reducing re-transmissions caused by transmission errors. Moreover, inspired by the TR-based C-RAN, we propose the compressive quantization scheme which applies to the uplink of multi-antenna C-RAN so that more antennas can be utilized with the limited front-haul capacity, which provide rich spatial diversity such that the massive TDs can be served more efficiently.