Damage detection in civil structures using high-frequency seismograms

The dynamic properties of a structure are a function of its physical properties, and changes in the physical properties of the structure, including the introduction of structural damage, can cause changes in its dynamic behavior. Structural health monitoring (SHM) and damage detection methods provide a means to assess the structural integrity and safety of a civil structure using measurements of its dynamic properties. In particular, these techniques enable a quick damage assessment following a seismic event. In this thesis, the application of high-frequency seismograms to damage detection in civil structures is investigated.

Two novel methods for SHM are developed and validated using small-scale experimental testing, existing structures in situ, and numerical testing. The first method is developed for pre-Northridge steel-moment-resisting frame buildings that are susceptible to weld fracture at beam-column connections. The method is based on using the response of a structure to a nondestructive force (i.e., a hammer blow) to approximate the response of the structure to a damage event (i.e., weld fracture). The method is applied to a small-scale experimental frame, where the impulse response functions of the frame are generated during an impact hammer test. The method is also applied to a numerical model of a steel frame, in which weld fracture is modeled as the tensile opening of a Mode I crack. Impulse response functions are experimentally obtained for a steel moment-resisting frame building in situ. Results indicate that while acceleration and velocity records generated by a damage event are best approximated by the acceleration and velocity records generated by a colocated hammer blow, the method may not be robust to noise. The method seems to be better suited for damage localization, where information such as arrival times and peak accelerations can also provide indication of the damage location. This is of significance for sparsely-instrumented civil structures.

The second SHM method is designed to extract features from high-frequency acceleration records that may indicate the presence of damage. As short-duration high-frequency signals (i.e., pulses) can be indicative of damage, this method relies on the identification and classification of pulses in the acceleration records. It is recommended that, in practice, the method be combined with a vibration-based method that can be used to estimate the loss of stiffness. Briefly, pulses observed in the acceleration time series when the structure is known to be in an undamaged state are compared with pulses observed when the structure is in a potentially damaged state. By comparing the pulse signatures from these two situations, changes in the high-frequency dynamic behavior of the structure can be identified, and damage signals can be extracted and subjected to further analysis. The method is successfully applied to a small-scale experimental shear beam that is dynamically excited at its base using a shake table and damaged by loosening a screw to create a moving part. Although the damage is aperiodic and nonlinear in nature, the damage signals are accurately identified, and the location of damage is determined using the amplitudes and arrival times of the damage signal. The method is also successfully applied to detect the occurrence of damage in a test bed data set provided by the Los Alamos National Laboratory, in which nonlinear damage is introduced into a small-scale steel frame by installing a bumper mechanism that inhibits the amount of motion between two floors. The method is successfully applied and is robust despite a low sampling rate, though false negatives (undetected damage signals) begin to occur at high levels of damage when the frequency of damage events increases. The method is also applied to acceleration data recorded on a damaged cable-stayed bridge in China, provided by the Center of Structural Monitoring and Control at the Harbin Institute of Technology. Acceleration records recorded after the date of damage show a clear increase in high-frequency short-duration pulses compared to those previously recorded. One undamage pulse and two damage pulses are identified from the data. The occurrence of the detected damage pulses is consistent with a progression of damage and matches the known chronology of damage.

Developing and characterizing bulk metallic glasses for extreme applications

Metallic glasses have typically been treated as a “one size fits all” type of material. Every alloy is considered to have high strength, high hardness, large elastic limits, corrosion resistance, etc. However, similar to traditional crystalline materials, properties are strongly dependent upon the constituent elements, how it was processed, and the conditions under which it will be used. An important distinction which can be made is between metallic glasses and their composites. Charpy impact toughness measurements are performed to determine the effect processing and microstructure have on bulk metallic glass matrix composites (BMGMCs). Samples are suction cast, machined from commercial plates, and semi-solidly forged (SSF). The SSF specimens have been found to have the highest impact toughness due to the coarsening of the dendrites, which occurs during the semi-solid processing stages. Ductile to brittle transition (DTBT) temperatures are measured for a BMGMC. While at room temperature the BMGMC is highly toughened compared to a fully glassy alloy, it undergoes a DTBT by 250 K. At this point, its impact toughness mirrors that of the constituent glassy matrix. In the following chapter, BMGMCs are shown to have the capability of being capacitively welded to form single, monolithic structures. Shear measurements are performed across welded samples, and, at sufficient weld energies, are found to retain the strength of the parent alloy. Cross-sections are inspected via SEM and no visible crystallization of the matrix occurs.

Next, metallic glasses and BMGMCs are formed into sheets and eggbox structures are tested in hypervelocity impacts. Metallic glasses are ideal candidates for protection against micrometeorite orbital debris due to their high hardness and relatively low density. A flat single layer, flat BMG is compared to a BMGMC eggbox and the latter creates a more diffuse projectile cloud after penetration. A three tiered eggbox structure is also tested by firing a 3.17 mm aluminum sphere at 2.7 km/s at it. The projectile penetrates the first two layers, but is successfully contained by the third.

A large series of metallic glass alloys are created and their wear loss is measured in a pin on disk test. Wear is found to vary dramatically among different metallic glasses, with some considerably outperforming the current state-of-the-art crystalline material (most notably Cu₄₃Zr₄₃Al₇Be₇). Others, on the other hand, suffered extensive wear loss. Commercially available Vitreloy 1 lost nearly three times as much mass in wear as alloy prepared in a laboratory setting. No conclusive correlations can be found between any set of mechanical properties (hardness, density, elastic, bulk, or shear modulus, Poisson’s ratio, frictional force, and run in time) and wear loss. Heat treatments are performed on Vitreloy 1 and Cu₄₃Zr₄₃Al₇Be₇. Anneals near the glass transition temperature are found to increase hardness slightly, but decrease wear loss significantly. Crystallization of both alloys leads to dramatic increases in wear resistance. Finally, wear tests under vacuum are performed on the two alloys above. Vitreloy 1 experiences a dramatic decrease in wear loss, while Cu₄₃Zr₄₃Al₇Be₇ has a moderate increase. Meanwhile, gears are fabricated through three techniques: electrical discharge machining of 1 cm by 3 mm cylinders, semisolid forging, and copper mold suction casting. Initial testing finds the pin on disk test to be an accurate predictor of wear performance in gears.

The final chapter explores an exciting technique in the field of additive manufacturing. Laser engineered net shaping (LENS) is a method whereby small amounts of metallic powders are melted by a laser such that shapes and designs can be built layer by layer into a final part. The technique is extended to mixing different powders during melting, so that compositional gradients can be created across a manufactured part. Two compositional gradients are fabricated and characterized. Ti 6Al¬ 4V to pure vanadium was chosen for its combination of high strength and light weight on one end, and high melting point on the other. It was inspected by cross-sectional x-ray diffraction, and only the anticipated phases were present. 304L stainless steel to Invar 36 was created in both pillar and as a radial gradient. It combines strength and weldability along with a zero coefficient of thermal expansion material. Only the austenite phase is found to be present via x-ray diffraction. Coefficient of thermal expansion is measured for four compositions, and it is found to be tunable depending on composition.

Avaliação da microestrutura, microdureza e resistência à corrosão de juntas soldadas de uma liga de Ni-Cr obtidas através de diferentes processos de soldagem

Este trabalho avaliou o comportamento eletroquímico do metal de base (MB) de uma liga a base de níquel-cromo em relação a juntas soldadas desta liga obtidas pelos processos de brasagem (BRA) e Tungsten Inert Gas (TIG), imersos em saliva artificial com pH 2,5 e 5,5. Foram também realizados ensaios de microdureza e caracterização microestrutural, por meio de microscopia óptica e eletrônica de varredura e análise química semi-quantitativa por EDS, nos grupos MB, TIG, BRA e no cordão de solda a laser (LAS). O MB apresentou uma matriz rica em níquel e cromo, distribuída em um arranjo dendrítico típico, apresentando inclusões metálicas de silício e titânio, além de porosidades. As soldas TIG e LAS revelaram uma microestrutura mais refinada que o MB, mostrando, entretanto, uma mesma composição química e distribuição de seus elementos. A solda BRA apresentou diferenças marcantes em sua microestrutura, composição química e distribuição de seus elementos em relação ao MB. Os dados de microdureza Vickers (HV), potencial de corrosão (Ecorr) e densidade de corrente de corrosão (jcorr) foram analisados com ANOVA e teste de Tukey (p<0,05). Para determinação da influência do pH quanto a resistência à corrosão dos grupos MB, TIG e BRA, empregou-se o teste t de Student (p<0,05). O MB apresentou menor média de microdureza (256,13 9,39 HV), seguido pelos grupos TIG (271,53 8,07 HV), LAS (303,73 13,93 HV) e BRA (551,99 37,73 HV). Em pH 2,5 as médias do Ecorr (mV) para o MB, TIG e BRA foram, respectivamente, -67,9 8,43, -52,78 16,74, e -284,33 19,04; e em pH 5,5, médias de -54,03 21,15, -62,08 20,16 e -278,8 28,96. Os valores médios de jcorr (A.cm-2) para o MB, TIG e BRA em pH 2,5 foram, respectivamente, 2,49 0,95, 5,584 1,64 e 27,45 4,9; e em pH 5,5, médias de 1,929 0,83, 4,267 1,51 e 54,2 11,96. Os grupos MB e TIG apresentaram boa resistência à corrosão, com maior módulo de impedância em relação ao grupo BRA. As diferenças no pH da saliva artificial não alteraram o comportamento corrosivo dos grupos MB e TIG. Entretanto, observou-se uma redução marcante na jcorr e no módulo de impedância nas soldas obtidas pelo processo de brasagem. O grupo BRA apresentou corrosão galvânica ao ser analisado formando par com o MB, mostrando uma jcorr de 5,3 A.cm-2. Entretanto, o mesmo não foi observado quando o MB foi associado à solda TIG, onde a jcorr foi cerca de 150 vezes menor. O grupo BRA, além de apresentar um comportamento eletroquímico muito diferente do MB, revelou diferenças marcantes quanto a composição química, aspecto microestrutural e microdureza. As juntas TIG e LAS mostraram semelhanças químicas e microestruturais em relação ao MB, sendo que na solda TIG esta semelhança foi ainda mais evidente. Além disto, a solda TIG apresentou um comportamento eletroquímico muito semelhante ao MB e, portanto, parecendo ser mais recomendável para soldar ligas odontológicas de níquel-cromo em relação aos demais processos de soldagem aqui avaliados.

Bericht über vergleichende Untersuchungen zur Lagerung von Fischfilet in konventionellen und mit Silbernanopartikeln beaufschlagten Verpackungen

Kurzfassung Die Lebensmittelbranche erwartet durch den Einsatz von Nanotechnologien hervorragende Fortschritte bei der Verbesserung der Produktqualität und der Lebensmittelsicherheit. Vor diesem Hintergrund wurde 2009 am Max Rubner Institut der Fach- und Institutsübergreifende Forschungsschwerpunkt „Nanotechnologie“ etabliert, um Grundlagen zu erarbeiten, aufgrund derer die Auswirkungen der Nanotechnologie auf Lebensmittel und damit die Ernährung und Gesundheit der Verbraucher beurteilt werden können. In diesem Forschungsprojekt wurde der Einfluss neuer, mit Nanopartikeln beaufschlagter Verpackungsfolien auf Fischfilet untersucht. Abstract: The food industry expects by the application of nanotechnology excellent progress in the improvement of the product quality and the food safety. On this background the Max Rubner Institute established in 2009 an interdisciplinary focus on nanotecchnology research to formulate principles upon which the impact of nanotechnology on food and thus the nutrition and health of consumers can be assessed. In this research, the impact of new, nanoparticles containing packaging films was examined for fish fillet.

PCR-SSCP and Isoelectric Focusing as Screening Methods for Identification of (Sub-) Tropical Fish Species

To ensure the authentication of fishery products lacking biological characters, rapid species identification methods are required. Two DNA- and protein-based methods, PCR-SSCP (polymerase chain reaction - single strand conformation polymorphism) of a 464 bp segment of the cytochrome b – gene and isoelectric focusing (IEF) of water-soluble proteins from fish fillets, were applied to identify fillets of (sub-) tropical fish species available on the European market. Among the samples analysed were two taxonomically identified species from the family Sciaenidae and one from Sphyraenidae. By comparison of DNA- and protein patterns of different samples, information about intra-species variability of patterns, and homogeneity of batches (e.g. fillet blocks or bags) can be obtained. PCR-SSCP and IEF may be useful for pre-checking of a large number of samples by food control laboratories. Zusammenfassung Zur Sicherstellung der Authentizität von Fischerei-Erzeugnissen ohne biologische Merkmale sind schnelle Verfahren zur Speziesidentifizierung hilfreich. Zwei Methoden der DNA- bzw. Protein-Analyse wurden eingesetzt, um Filets (sub-) tropischer Fischarten, die auf dem europäischen Markt angeboten werden, zu identifizieren. Bei diesen Methoden handelt es sich um die PCR-SSCP (Polymerase-Kettenreaktion – Einzelstrang-Konformationspolymorphismus) – Analyse der PCR-Produkte und die IEF (isoelektrische Fokussierung) der wasserlöslichen Fischmuskelproteine. Unter den untersuchten Proben waren zwei taxonomisch bestimmte Arten aus der Familie Sciaenidae und eine Spezies aus der Familie Sphyraenidae. Durch Vergleich der DNA- bzw. Proteinmuster lassen sich Informationen über die intra-spezifische Variabilität solcher Muster und die Einheitlichkeit von Partien (beispielsweise Filetblöcke oder Filetbeutel) gewinnen. PCR-SSCP und IEF können in Laboratorien der Lebensmittelüberwachung als Vortest gerade bei hohen Probenzahlen sinnvoll eingesetzt werden.

Análise multielementar em peças de ouro antigo utilizando fluorescência de raios X por dispersão em energia

Os métodos de análise não destrutiva vêm sendo largamente empregados na área de Arqueometria. Estes métodos analisam artefatos históricos e obras de arte fornecendo informações da composição, das técnicas utilizadas e do local de manufatura da época. Assim, é possível fazer a datação, estabelecer a autenticidade e avaliar técnicas de conservação e restauração. A Fluorescência de Raios X por Dispersão de Energia (EDXRF) é um método que permite fazer análises quantitativas e qualitativas multielementares dos artefatos de forma não destrutiva. Neste estudo foram analisados artefatos compostos por ouro de diferentes épocas através da técnica de Fluorescência de Raios X por Dispersão em Energia (EDXRF). Dentre os artefatos, encontram-se brincos, pingentes, estatuetas e adornos de roupa cedidos pelo Instituto de Pesquisa Histórica e Arqueológica do Rio de Janeiro (IPHARJ). As análises foram realizadas através do sistema comercial ARTAX 200. Este sistema possui ânodo de Molibdênio. Foi utilizado um filtro de alumínio com 315 μm de espessura e foi operado em 40 kV, 250 μA com 300 s de aquisição. As concentrações de Cu, Au e Ag foram obtidas através da curva de calibração feita com padrões de ouro de 24k, 18k, 16k, 14k, 12k e 10k. Os resultados mostram que todas as peças contêm ligas metálicas e ouro em diferentes concentrações em sua composição. A partir das diferenças nas concentrações de ouro, foi possível classificar as peças quanto à pureza do ouro (quilatagem). Além disso, foi possível estimar a época em que estas peças foram manufaturadas a partir da comparação dos resultados encontrados com aqueles encontrados na literatura.

Nutritional properties of the invasive lionfish: A delicious and nutritious approach for controlling the invasion

Lionfish, Pterois volitans and P. miles, are native to the Indo-Pacific and have recently invaded the Western Atlantic Ocean. Strategies for control of this invasion have included limited removal programs and promotion of lionfish consumption at both local and commercial scales. We demonstrate that lionfish meat contains higher levels of healthy n-3 fatty acids than some frequently consumed native marine fish species. Mean lionfish fillet yield was 30.5% of the total body wet weight, a value that is similar to that of some grouper and porgy species. A sensory evaluation indicated that lionfish meet the acceptability threshold of most consumers.

Wear of hardfacing white cast irons by solid particle erosion

The response of three commercial weld-hardfacing alloys to erosive wear has been studied. These were high chromium white cast irons, deposited by an open-arc welding process, widely used in the mineral processing and steelmaking industries for wear protection. Erosion tests were carried out with quartz sand, silicon carbide grit and blast furnace sinter of two different sizes, at a velocity of 40 m s-1 and at impact angles in the range 20° to 90°. A monolithic white cast iron and mild steel were also tested for comparison. Little differences were found in the wear rates when silica sand or silicon carbide grit was used as the erodent. Significant differences were found, however, in the rankings of the materials. Susceptibility to fracture of the carbide particles in the white cast irons played an important role in the behaviour of the white cast irons. Sinter particles were unable to cause gross fracture of the carbides and so those materials with a high volume fraction of carbides showed the greatest resistance to erosive wear. Silica and silicon carbide were capable of causing fracture of the primary carbides. Concentration of plastic strain in the matrix then led to a high wear rate for the matrix. At normal impact with silica or silicon carbide erodents mild steel showed a greater resistance to erosive wear than these alloys. © 1995.

Some biochemical constituents and the calorific values of different regions of the body musculature of pond murrel Channa punctatus Bloch

A study of the distribution of some chemical constituents in the musculature of Channa punctatus Bloch showed it to be fairly heterogeneous. The increase in the levels of protein, fat, ash, total carbohydrates, glycogen, RNA, DNA and cholesterol towards the posterior region of the fillet was the result of increase in the number of cells per unit weight of the sample and in the concentration of myocommata. The distribution of water in the musculature was inversely related to that of the fat. The concentration of protein appeared to be associated with the RNA level. The posterior region of the fillet exhibited more calorific value than the anterior region.

Statistical quality control charts on attributes in fish processing technology

Apart from the use of statistical quality control chart for variables or attributes of food products in a food processing industry, the application of these charts for attributes of fishery products is explained. Statistical quality control chart for fraction defectives is explained by noting defective fish sausages per shift from a sausage industry while control chart for number of defectives is illustrated for number of defective fish cans in each hour of its production of a canning industry. C-chart is another type of control chart which is explained here for number of defects per single fish fillet sampled a1l random for every five minutes in a processing industry. These statistical quality control charts help in the more economic use of resource, time and labour than control charts for variables of products. Also control charts for attributes exhibit the quality history of finished products at different times of production thereby minimizing the risk of consumer rejection.

Investigations on long distance transportation of fish. 5. Transportation of filleted and round seer fish (Scomberomorus sp.) from Kakinada to Calcutta by rail

Iced seer fish (Scomberomorus sp.) was transported by rail in expanded polystyrene insulated plywood boxes from Kakinada to Calcutta in round and fillet forms. While both withstood the rigors of transportation squarely, the fillets fetched only half the price of round fish in the auction conducted at the Calcutta market.

Effect of box stowage on quality fish

Quality of boxed cod and haddock was compared with that of penned fish in terms of organoleptic grading, trimethylamine values, Intelectron Fish Tester readings and fish and fillet yield. Boxed fish showed a higher percentage of grade one fish than penned fish. TMA values, however, did not differ greatly. There was less physical damage due to squeezing with boxed fish and consequently a greater yield of landed round fish and fillets.

Studies on frozen storage of cuttle fish fillets

The freezing and cold storage characteristics of cuttle fish fillets have been studied. The yield of fillets from cuttle fish was about 35% and the fillet had an average moisture content of 76.85% and fat 0.82% During storage at -20 ± 1°C for 16 months the salt soluble nitrogen of the fillets decreased from 85.1to35.36%, the non-protein nitrogen from 24.61 to 20.84% and alpha amino nitrogen from 252 to 140mg/100g. Initially the fillets were white in colour, showed signs of desiccation by 4 months storage which increased on further storage and the fillets finally became dull white with yellow discolouration inside. The firm and chewy texture of the cooked fillets changed to rubbery even though the product was slightly sweet at the end of that storage period of 16 months.