Death or taxes? The political economy of sanitation expenditure in nineteenth-century Britain

This thesis consists of three papers studying the relationship between democratic reform, expenditure on sanitation public goods and mortality in Britain in the second half of the nineteenth century. During this period decisions over spending on critical public goods such as water supply and sewer systems were made by locally elected town councils, leading to extensive variation in the level of spending across the country. This dissertation uses new historical data to examine the political factors determining that variation, and the consequences for mortality rates.

The first substantive chapter describes the spread of government sanitation expenditure, and analyzes the factors that determined towns' willingness to invest. The results show the importance of towns' financial constraints, both in terms of the available tax base and access to borrowing, in limiting the level of expenditure. This suggests that greater involvement by Westminster could have been very effective in expediting sanitary investment. There is little evidence, however, that democratic reform was an important driver of greater expenditure.

Chapter 3 analyzes the effect of extending voting rights to the poor on government public goods spending. A simple model predicts that the rich and the poor will desire lower levels of public goods expenditure than the middle class, and so extensions of the right to vote to the poor will be associated with lower spending. This prediction is tested using plausibly exogenous variation in the extent of the franchise. The results strongly support the theoretical prediction: expenditure increased following relatively small extensions of the franchise, but fell once more than approximately 50% of the adult male population held the right to vote.

Chapter 4 tests whether the sanitary expenditure was effective in combating the high mortality rates following the Industrial Revolution. The results show that increases in urban expenditure on sanitation-water supply, sewer systems and streets-was extremely effective in reducing mortality from cholera and diarrhea.

Beyond Q-Resolution and Prenex Form: a Proof System for Quantified Constraint Satisfaction

We consider the quanti fied constraint satisfaction problem (QCSP) which is to decide, given a structure and a first-order sentence (not assumed here to be in prenex form) built from conjunction and quanti fication, whether or not the sentence is true on the structure. We present a proof system for certifying the falsity of QCSP instances and develop its basic theory; for instance, we provide an algorithmic interpretation of its behavior. Our proof system places the established Q-resolution proof system in a broader context, and also allows us to derive QCSP tractability results.

The use of object oriented modelling and simulation tools in constraint satisfaction for embodiment design

The software package Dymola, which implements the new, vendor-independent standard modelling language Modelica, exemplifies the emerging generation of object-oriented modelling and simulation tools. This paper shows how, in addition to its simulation capabilities, it may be used as an embodiment design tool, to size automatically a design assembled from a library of generic parametric components. The example used is a miniature model aircraft diesel engine. To this end, the component classes contain extra algebraic equations calculating the overload factor (or its reciprocal, the safety factor) for all the different modes of failure, such as buckling or tensile yield. Thus the simulation results contain the maximum overload or minimum safety factor for each failure mode along with the critical instant and the device state at which it occurs. The Dymola "Initial Conditions Calculation" function, controlled by a simple software script, may then be used to perform automatic component sizing. Each component is minimised in mass, subject to a chosen safety factor against failure, over a given operating cycle. Whilst the example is in the realm of mechanical design, it must be emphasised that the approach is equally applicable to the electrical or mechatronic domains, indeed to any design problem requiring numerical constraint satisfaction.

Genetic evidence of a strong functional constraint of neurotrypsin during primate evolution

Neurotrypsin is one of the extra-cellular serine proteases that are predominantly expressed in the brain and involved in neuronal development and function. Mutations in humans are associated with autosomal recessive non-syndromic mental retardation (MR). We studied the molecular evolution of neurotrypsin by sequencing the coding region of neurotrypsin in 11 representative non-human primate species covering great apes, lesser apes, Old World monkeys and New World monkeys. Our results demonstrated a strong functional constraint of neurotrypsin that was caused by strong purifying selection during primate evolution, an implication of an essential functional role of neurotrypsin in primate cognition. Further analysis indicated that the purifying selection was in fact acting on the SRCR domains of neurotrypsin, which mediate the binding activity of neurotrypsin to cell surface or extracellular proteins. In addition, by comparing primates with three other mammalian orders, we demonstrated that the absence of the first copy of the SRCR domain (exon 2 and 3) in mouse and rat was due to the deletion of this segment in the murine lineage. Copyright (C) 2005 S. Karger AG, Basel.

Mechanical constraint and loading on ferroelectric memory capacitors

The influence of mechanical constraint imposed by device geometry upon the switching response of a ferroelectric thin film memory capacitor is investigated. The memory capacitor was represented by two-dimensional ferroelectric islands of different aspect ratio, mechanically constrained by surrounding materials. Its ferroelectric non-linear behaviour was modeled by a crystal plasticity constitutive law and calculated using the finite element method. The switching response of the device, in terms of remnant charge storage, was determined as a function of geometry and constraint. The switching response under applied in-plane tensile stress and hydrostatic pressure was also studied experimentally. Our results showed that (1) the capacitor's aspect ratio could significantly affect the clamping behaviour and thus the remnant polarization, (2) it was possible to maximise the switching charge through the optimisation of the device geometry, and (3) it is possible to find a critical switching stress at zero electric field and a critical coercive field at zero residual stress. © 2009 Materials Research Society.