Optimization of electroless copper plating on polyethylene films modified by surface grafting of vinyl ether of monoethanolamine

Metallized plastics have recently received significant interest for their useful applications in electronic devices such as for integrated circuits, packaging, printed circuits and sensor applications. In this work the metallized films were developed by electroless copper plating of polyethylene films grafted with vinyl ether of monoethanoleamine. There are several techniques for metal deposition on surface of polymers such as evaporation, sputtering, electroless plating and electrolysis. In this work the metallized films were developed by electroless copper plating of polyethylene films grafted with vinyl ether of monoethanoleamine. Polyethylene films were subjected to gamma-radiation induced surface graft copolymerization with vinyl ether of monoethanolamine. Electroless copper plating was carried out effectively on the modified films. The catalytic processes for the electroless copper plating in the presence and the absence of SnCl2 sensitization were studied and the optimum activation conditions that give the highest plating rate were determined. The effect of grafting degree on the plating rate is studied. Electroless plating conditions (bath additives, pH and temperature) were optimized. Plating rate was determined gravimetrically and spectrophotometrically at different grafting degrees. The results reveal that plating rate is a function of degree of grafting and increases with increasing grafted vinyl ether of monoethanolamine onto polyethylene. It was found that pH 13 of electroless bath and plating temperature 40°C are the optimal conditions for the plating process. The increasing of grafting degree results in faster plating rate at the same pH and temperature. The surface morphology of the metallized films was investigated using scanning electron microscopy (SEM). The adhesion strength between the metallized layer and grafted polymer was studied using tensile machine. SEM photos and adhesion measurements clarified that uniform and adhered deposits were obtained under optimum conditions.

Investigation of cadmium alternatives in thin-film coatings - art. no. 62860C

The health risks associated with the inhalation or ingestion of cadmium are well documented([1,2]). During the past 18 years, EU legislation has steadily been introduced to restrict its use, leaving a requirement for the development of replacement materials. This paper looks at possible alternatives to various cadmium II-VI dielectric compounds used in the deposition of optical thin-films for various opto-electronic devices. Application areas of particular interest are for infrared multilayer interference filter fabrication and solar cell industries, where cadmium-based coatings currently find widespread use. The results of single and multilayer designs comprising CdTe, CdS, CdSe and PbTe deposited onto group IV and II-VI materials as interference filters for the mid-IR region are presented. Thin films of SnN, SnO2, SnS and SnSe are fabricated by plasma assisted CVD, reactive RF sputtering and thermal evaporation. Examination of these films using FTIR spectroscopy, SEM, EDX analysis and optical characterisation methods provide details of material dispersion, absorption, composition, refractive index, energy band gap and layer thicknesses. The optimisation of deposition parameters in order to synthesise coatings with similar optical and semiconductor properties as those containing cadmium has been investigated. Results of environmental, durability and stability trials are also presented.

Conductance of amyloid β based peptide filaments: structure–function relations.

Controlling the morphology of self-assembled peptide nanostructures, particularly those based on amyloid peptides, has been the focus of intense research. In order to exploit these structures in electronic applications, further understanding of their electronic behavior is required. In this work, the role of peptide morphology in determining electronic conduction along self-assembled peptide nanofilament networks is demonstrated. The peptides used in this work were based on the sequence AAKLVFF, which is an extension of a core sequence from the amyloid b peptide. We show that the incorporation of a non-natural amino acid, 2-thienylalanine, instead of phenylalanine improves the obtained conductance with respect to that obtained for a similar structure based on the native sequence, which was not the case for the incorporation of 3-thienylalanine. Furthermore, we demonstrate that the morphology of the self-assembled structures, which can be controlled by the solvent used in the assembly process, strongly affects the conductance, with larger conduction obtained for a morphology of long, straight filaments. Our results demonstrate that, similar to natural systems, the assembly and folding of peptides could be of great importance for optimizing their function as components of electronic devices. Hence, sequence design and assembly conditions can be used to control the performance of peptide based structures in such electronic applications.

Ab Initio Calculations of Structural Evolution and Conductance of Benzene-1,4-dithiol on Gold Leads

By performing at) initio density functional theory (DFT) calculations and electronic transport simulations based on the OFT nonequilibrium Green`s functions method we investigate how the conformational changes of a benzene-1,4-dithiol molecule bonded to gold affect the molecular transport as the electrodes are separated from each other. In particular we consider the full evolution of the stretching process until the Junction breaking point and compare results obtained with a standard semilocal exchange and correlation functional to those computed with a self-interaction corrected method. We conclude that the inclusion of self-interaction corrections is fundamental for describing both the molecule conductance and its stability against conformational fluctuations.

Probing the functionalization of gold surfaces and protein adsorption by PM-IRRAS

The control of morphology and coating of metal surfaces is essential for a number of organic electronic devices including photovoltaic cells and sensors. In this study, we monitor the functionalization of gold surfaces with 11-mercaptoundecanoic acid (MUA, HS(CH(2))(10)CO(2)H) and cysteamine, aiming at passivating the surfaces for application in surface plasmon resonance (SPR) biosensors. Using polarization-modulated infrared reflection-absorption spectroscopy (PM-IRRAS), cyclic voltammetry, atomic force microscopy and quartz crystal microbalance, we observed a time-dependent organization process of the adsorbed MUA monolayer with alkyl chains perpendicular to the gold surface. Such optimized condition for surface passivation was obtained with a systematic search for experimental parameters leading to the lowest electrochemical signal of the functionalized gold electrode. The ability to build supramolecular architectures was also confirmed by detecting with PM-IRRAS the adsorption of streptavidin on the MUA-functionalized gold. As the approaches used for surface functionalization and its verification with PM-IRRAS are generic, one may now envisage monitoring the fabrication of tailored electrodes for a variety of applications.

Influence of different solvents on the structural, optical and morphological properties of CdS nanoparticles

CdS is one of the most important II-VI semiconductors, with applications in solar cells, optoelectronics and electronic devices. CdS nanoparticles were synthesized via microwave-assisted solvothermal technique. Structural and morphological characterization revealed the presence of crystalline structures presenting single phase with different morphologies such as ""nanoflowers"" and nanoplates depending on the solvent used. Optical characterization was made by diffuse reflectance and photoluminescence spectroscopy, revealing the influence of the different solvents on the optical properties due to structural defects generated during synthesis. It is proposed that these defects are related to sulfur vacancies, with higher concentration of defects for the sample synthesized in ethylene glycol in comparison with the one synthesized in ethylene diamine. (C) 2011 Elsevier B.V. All rights reserved.

Ink-Jet Printing of Color Optical Filters for LCD Applications

At the age of multi-media, portable electronic devices such as mobile phones, personal digital assistant and handheld gaming systems have increased the demand for high performance displays with low cost production. Inkjet printing color optical filters (COF) for LCD applications seem to be an interesting alternative to decrease the production costs. The advantage of inkjet printing technology is to be fast, accurate, easy to run and cheaper than other technologies. In this master thesis work, we used various disciplines such as optical microscopy, rheology, inkjet printing, profilometering and colorimetry. The specific aim of the thesis was to investigate the feasibility of using company-A pigment formulation in inkjet production of COF for active matrix LCD applications. Ideal viscosity parameters were determined from 10 to 20mPa·s for easy inkjet printing at room temperature. The red pigments used are fully dispersed into the solvent and present an excellent homogenous repartition after printing. Thickness investigations revealed that the printed COF were equal or slightly thicker than typically manufactured ones. The colorimetry investigations demonstrated color coordinates very close to the NTSC red standard. LED backlighting seems to be a valuable solution to combine with the printed COF regarding to the spectrum and color analysis. The results on this thesis will increase the understanding of inkjet printing company-A pigments to produce COF for LCD applications.

Road network and GPS tracking with data processing and quality assessment

GPS technology has been embedded into portable, low-cost electronic devices nowadays to track the movements of mobile objects. This implication has greatly impacted the transportation field by creating a novel and rich source of traffic data on the road network. Although the promise offered by GPS devices to overcome problems like underreporting, respondent fatigue, inaccuracies and other human errors in data collection is significant; the technology is still relatively new that it raises many issues for potential users. These issues tend to revolve around the following areas: reliability, data processing and the related application. This thesis aims to study the GPS tracking form the methodological, technical and practical aspects. It first evaluates the reliability of GPS based traffic data based on data from an experiment containing three different traffic modes (car, bike and bus) traveling along the road network. It then outline the general procedure for processing GPS tracking data and discuss related issues that are uncovered by using real-world GPS tracking data of 316 cars. Thirdly, it investigates the influence of road network density in finding optimal location for enhancing travel efficiency and decreasing travel cost. The results show that the geographical positioning is reliable. Velocity is slightly underestimated, whereas altitude measurements are unreliable.Post processing techniques with auxiliary information is found necessary and important when solving the inaccuracy of GPS data. The densities of the road network influence the finding of optimal locations. The influence will stabilize at a certain level and do not deteriorate when the node density is higher.

A internet como ferramenta para venda de veículos: o caso Vitória Webcar

A possibilidade de interagir em tempo real com o consumidor, ao contrário dos monólogos que normalmente caracterizam os tradicionais meios de marketing, alterou drasticamente o jeito como o Customer Service pode ser oferecido, pois permite pesquisas e compras de produtos e serviços on-line, o que representa um maior conforto para o homem contemporâneo, cujo tempo é bem escasso. O mercado representa um papel central na economia de qualquer nação, facilitando a troca de informações, bens, serviços e pagamentos, além de criar valores econômicos para compradores, vendedores, intermediários e para a sociedade de modo geral. Os mercados provêem a infra-estrutura física que permite que as transações entre os compradores e os vendedores ocorram. Dessa forma, entende-se que Mercado e Negociação eletrônica são especializações dos conceitos gerais de Mercado e Negociação. O uso de meios eletrônicos e, mais especificamente, o uso da Internet como recurso para promover o comércio, tem revolucionado todas as formas de comercialização existentes, promovendo o surgimento de novos tipos de mercados eletrônicos, os mercados baseados em Internet. Com tais vantagens, os mercados eletrônicos geram novas oportunidades de negócios, proporcionam novas estratégias para se atingir o consumidor, o fornecedor e os intermediários que estejam dispostos a somar valores na integração cliente/fornecedor. Mercados eletrônicos melhoram as informações compartilhadas entre compradores e fornecedores e ajudam a reduzir o custo de logística permitindo promoções rápidas, entregas imediatas e inventários reduzidos. É a infra-estrutura da informação substituindo sistemas de distribuição física. Foi, portanto, sobre esta temática que buscou-se desenvolver todo o trabalho de pesquisa, enfocando-se um caso real: Vitória Web Car, por ser uma organização que direcionou o seu foco para a qualidade dos serviços, como base para o seu crescimento e diferenciação no mercado do varejo virtual brasileiro.

Fahrenheit 451, de Ray Bradbury e de François Truffaut : da alienação pós-moderna à oralidade homérica

Este trabalho analisa o Fahrenheit 451 de Ray Bradbury e o de François Truffaut, em sua proposição de utilizar a oralidade (discurso oral) como forma de manutenção do literário e resistência à imposição e à censura ideológica. Efetua também uma análise comparatista das Utopias Negativas do século XX (obras Distópicas). Ao longo deste projeto, é feita uma análise do surgimento da escrita (alfabético-fonética), e sua estreita relação com o discurso oral. Tenta-se reproduzir a trajetória traçada pelo discurso oral, passando pelo desenvolvimento da tecnologia escrita, assim como a produção cultural tanto no meio oral quanto no escrito, junto com suas conseqüências e influências sobre pensamento humano. Da oralidade dos poemas homéricos à oralidade advinda com o desenvolvimento de aparelhos eletrônicos como o telefone, que, em plena modernidade, voltam a valorizar o discurso oral. Neste projeto a oralidade é vista como algo cíclico.

WalkNRide: contextualising feedback in physical activity trackers

Increasing levels of sedentarism and obesity, along with advances in sensor technologies have instigated a market for wearable activity trackers, electronic devices that sense users’ physical activity levels with the goals of self-monitoring and behaviour change. Nowadays, activity trackers are one of the most desirable technologies, making up for a market of over $230 million in 2013. However, despite the spike of users’ interest, activity trackers have been shown to lose their appeal over time, with a recent survey suggesting that one out of three users discard the tracker in the course of the first six months of use. The question we pose is: how can we design activity tracker so that users’ interests is sustained over the long term? Our design approach focuses on contextualising physical activity. We do this through sensing users’ locations and activities (such as being still, walking or commuting through a car, bus or other means) and thus providing innovative ways of presenting feedback on users. This thesis presents the design and evaluation of WalkNRide, a physical activity tracker for Google Android. Through a longitudinal field study of WalkNRide, we attempt to inquire into the factors that drive the adoption (or non-adoption) of the tool as well as the ways in which the use of the tool contributes towards habit formation.

Caracterização de compósitos Nb-20%cu obtidos por moagem de alta energia e sinterizados por fase líquida

In this work, was studied the formation of a composite of the refractory metal niobium with copper, through the process of high-energy milling and liquid phase sintering. The HEM can be used to synthesize composite powders with high homogeneity and fine size particle distribution. It may also produce the solid solubility in immiscible systems such as Nb-Cu, or extend the solubility of systems with limited solubility. Therefore, in the immiscible system Cu-Nb, the high-energy milling was successfully used to obtain the composite powder particles. Initially, the formation of composite particles during the HEM and the effect of preparation technique on the microstructure of the material was evaluated. Four loads of Nb and Cu powders containing 20%wt Cu were synthesized by MAE in a planetary type ball mill under different periods of grinding. The influence of grinding time on the metal particles is evaluated during the process by the withdrawal of samples at intermediate times of milling. After compaction under different forces, the samples were sintered in a vacuum furnace. The liquid phase sintering of these samples prepared by HEM produced a homogeneous and fine grained. The composite particles forming the sintered samples are the addition of a hard phase (Nb) with a high melting point, and a ductile phase (Cu) with low melting point and high thermal and electrical conductivities. Based on these properties, the Nb-Cu system is a potential material for many applications, such as electrical contacts, welding electrodes, coils for generating high magnetic fields, heat sinks and microwave absorbers, which are coupled to electronic devices. The characterization techniques used in this study, were laser granulometry, used to evaluate the homogeneity and particle size, and the X-ray diffraction, in the phase identification and to analyze the crystalline structure of the powders during milling. The morphology and dispersion of the phases in the composite powder particles, as well the microstructures of the sintered samples, were observed by scanning electron microscopy (SEM). Subsequently, the sintered samples are evaluated for density and densification. And finally, they were characterized by techniques of measuring the electrical conductivity and microhardness, whose properties are analyzed as a function of the parameters for obtaining the composite

Dispositivos flexíveis de monitoramento de pH e de deflexão mecânica à base de polianilina

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Iron phthalocyanine in non-aqueous medium forming layer-by-layer films: growth mechanism, molecular architecture and applications

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeito Peltier em estruturas semicondutoras quasiperiódicas

There is nowadays a growing demand for located cooling and stabilization in optical and electronic devices, haul of portable systems of cooling that they allow a larger independence in several activities. The modules of thermoelectrical cooling are bombs of heat that use efect Peltier, that consists of the production of a temperature gradient when an electric current is applied to a thermoelectrical pair formed by two diferent drivers. That efect is part of a class of thermoelectrical efcts that it is typical of junctions among electric drivers. The modules are manufactured with semiconductors. The used is the bismuth telluride Bi2Te3, arranged in a periodic sequence. In this sense the idea appeared of doing an analysis of a system that obeys the sequence of Fibonacci. The sequence of Fibonacci has connections with the golden proportion, could be found in the reproductive study of the bees, in the behavior of the light and of the atoms, as well as in the growth of plants and in the study of galaxies, among many other applications. An apparatus unidimensional was set up with the objective of investigating the thermal behavior of a module that obeys it a rule of growth of the type Fibonacci. The results demonstrate that the modules that possess periodic arrangement are more eficient