On thermodynamics in the primary power conversion of oscillating water column wave energy converters

The paper presents an investigation to the thermodynamics of the air flow in the air chamber for the oscillating water column wave energy converters, in which the oscillating water surface in the water column pressurizes or de-pressurises the air in the chamber. To study the thermodynamics and the compressibility of the air in the chamber, a method is developed in this research: the power take-off is replaced with an accepted semi-empirical relationship between the air flow rate and the oscillating water column chamber pressure, and the thermodynamic process is simplified as an isentropic process. This facilitates the use of a direct expression for the work done on the power take-off by the flowing air and the generation of a single differential equation that defines the thermodynamic process occurring inside the air chamber. Solving the differential equation, the chamber pressure can be obtained if the interior water surface motion is known or the chamber volume (thus the interior water surface motion) if the chamber pressure is known. As a result, the effects of the air compressibility can be studied. Examples given in the paper have shown the compressibility, and its effects on the power losses for large oscillating water column devices.

Performance improvements of mooring systems for wave energy converters

In the development of wave energy converters, the mooring system is a key component for a safe station-keeping and an important factor in the cost of the wave energy production. Generally, when designing a mooring system for a wave energy converter, two important conditions must be considered: (i) that the mooring system must be strong enough to limit the drifting motions, even in extreme waves, tidal and wind conditions and (ii) it must be compliant enough so that the impact on wave energy production can be minimised. It is frequently found that these two conditions are contradictory. The existing solutions mainly include the use of heavy chains, which create a catenary shaped mooring configuration, allowing limited flexibility within the mooring system, and hence very large forces may still be present on mooring lines and thus on anchors. This solution is normally quite expensive if the costs of the materials and installation are included. This paper presents a new solution to the mooring system for wave energy converters within the FP7 project, ‘GeoWAVE’, which is a project aiming to develop a new generation of the moorings system for minimising the loads on mooring lines and anchors, the impact on the device motions for power conversion, and the footprint if it is applicable, and meanwhile the new types of anchors are also addressed within the project. However this paper will focus on the new mooring system by presenting the wave tank test results of the Pelamis wave energy converter model and the new developed mooring system. It can be seen that the new generation of mooring system can significantly reduce the loads on mooring lines and anchors, and reduce the device excursions as a result of the new mooring system when compare to the conventional catenary mooring.

A new latching control technology for improving wave energy conversion

Extracting wave energy from seas has been proven to be very difficult although various technologies have been developed since 1970s. Among the proposed technologies, only few of them have been actually progressed to the advanced stages such as sea trials or pre-commercial sea trial and engineering. One critical question may be how we can design an efficient wave energy converter or how the efficiency of a wave energy converter can be improved using optimal and control technologies, because higher energy conversion efficiency for a wave energy converter is always pursued and it mainly decides the cost of the wave energy production. In this first part of the investigation, some conventional optimal and control technologies for improving wave energy conversion are examined in a form of more physical meanings, rather than the purely complex mathematical expressions, in which it is hoped to clarify some confusions in the development and the terminologies of the technologies and to help to understand the physics behind the optimal and control technologies. As a result of the understanding of the physics and the principles of the optima, a new latching technology is proposed, in which the latching duration is simply calculated from the wave period, rather than based on the future information/prediction, hence the technology could remove one of the technical barriers in implementing this control technology. From the examples given in the context, this new latching control technology can achieve a phase optimum in regular waves, and hence significantly improve wave energy conversion. Further development on this latching control technologies can be found in the second part of the investigation.

Performance study of the Galway Bay wave energy test site floating power system

The Galway Bay wave energy test site promises to be a vital resource for wave energy researchers and developers. As part of the development of this site, a floating power system is being developed to provide power and data acquisition capabilities, including its function as a local grid connection, allowing for the connection of up to three wave energy converter devices. This work shows results from scaled physical model testing and numerical modelling of the floating power system and an oscillating water column connected with an umbilical. Results from this study will be used to influence further scaled testing as well as the full scale design and build of the floating power system in Galway Bay.

Biomass, quality traits and methane production of extensive grassland: biodiversity effects and sensor approaches

Energy policies around the world are mandating for a progressive increase in renewable energy production. Extensive grassland areas with low productivity and land use limitations have become target areas for sustainable energy production to avoid competition with food production on the limited available arable land resources and minimize further conversion of grassland into intensively managed energy cropping systems or abandonment. However, the high spatio-temporal variability in botanical composition and biochemical parameters is detrimental to reliable assessment of biomass yield and quality regarding anaerobic digestion. In an approach to assess the performance for predicting biomass using a multi-sensor combination including NIRS, ultra-sonic distance measurements and LAI-2000, biweekly sensor measurements were taken on a pure stand of reed canary grass (Phalaris aruninacea), a legume grass mixture and a diversity mixture with thirty-six species in an experimental extensive two cut management system. Different combinations of the sensor response values were used in multiple regression analysis to improve biomass predictions compared to exclusive sensors. Wavelength bands for sensor specific NDVI-type vegetation indices were selected from the hyperspectral data and evaluated for the biomass prediction as exclusive indices and in combination with LAI and ultra-sonic distance measurements. Ultrasonic sward height was the best to predict biomass in single sensor approaches (R² 0.73 – 0.76). The addition of LAI-2000 improved the prediction performance by up to 30% while NIRS barely improved the prediction performance. In an approach to evaluate broad based prediction of biochemical parameters relevant for anaerobic digestion using hyperspectral NIRS, spectroscopic measurements were taken on biomass from the Jena-Experiment plots in 2008 and 2009. Measurements were conducted on different conditions of the biomass including standing sward, hay and silage and different spectroscopic devices to simulate different preparation and measurement conditions along the process chain for biogas production. Best prediction results were acquired for all constituents at laboratory measurement conditions with dried and ground samples on a bench-top NIRS system (RPD > 3) with a coefficient of determination R2 < 0.9. The same biomass was further used in batch fermentation to analyse the impact of species richness and functional group composition on methane yields using whole crop digestion and pressfluid derived by the Integrated generation of solid Fuel and Biogas from Biomass (IFBB) procedure. Although species richness and functional group composition were largely insignificant, the presence of grasses and legumes in the mixtures were most determining factors influencing methane yields in whole crop digestion. High lignocellulose content and a high C/N ratio in grasses may have reduced the digestibility in the first cut material, excess nitrogen may have inhibited methane production in second cut legumes, while batch experiments proved superior specific methane yields of IFBB press fluids and showed that detrimental effects of the parent material were reduced by the technical treatment

Estimating Bat and Bird Mortality Occurring at Wind Energy Turbines from Covariates and Carcass Searches Using Mixture Models

Environmental impacts of wind energy facilities increasingly cause concern, a central issue being bats and birds killed by rotor blades. Two approaches have been employed to assess collision rates: carcass searches and surveys of animals prone to collisions. Carcass searches can provide an estimate for the actual number of animals being killed but they offer little information on the relation between collision rates and, for example, weather parameters due to the time of death not being precisely known. In contrast, a density index of animals exposed to collision is sufficient to analyse the parameters influencing the collision rate. However, quantification of the collision rate from animal density indices (e.g. acoustic bat activity or bird migration traffic rates) remains difficult. We combine carcass search data with animal density indices in a mixture model to investigate collision rates. In a simulation study we show that the collision rates estimated by our model were at least as precise as conventional estimates based solely on carcass search data. Furthermore, if certain conditions are met, the model can be used to predict the collision rate from density indices alone, without data from carcass searches. This can reduce the time and effort required to estimate collision rates. We applied the model to bat carcass search data obtained at 30 wind turbines in 15 wind facilities in Germany. We used acoustic bat activity and wind speed as predictors for the collision rate. The model estimates correlated well with conventional estimators. Our model can be used to predict the average collision rate. It enables an analysis of the effect of parameters such as rotor diameter or turbine type on the collision rate. The model can also be used in turbine-specific curtailment algorithms that predict the collision rate and reduce this rate with a minimal loss of energy production.

Renewable energy scenarios for South Karelia – non-industrial energy demands

Tässä diplomityössä tarkastellaan täysin uusiutuvaa energiajärjestelmää Etelä-Karjalan maakunnan alueella, mikä onkin jo tällä hetkellä Suomen uusiutuvin maakunta. Diplomityössä tarkastellaan julkisen sektorin, liikenteen ja rakennusten energian kulutusta mutta teollisuuden energiankäyttö jätetään tarkastelun ulkopuolelle. Työssä tutustutaan tämän hetken Etelä-Karjalan energiajärjestelmään ja sen perusteella tehdään referenssi-skenaario. Tulevaisuuden skenaariot tehdään vuosille 2030 ja 2050. Tulevaisuuden skenaarioissa muutos keskittyy järjestelmän sähköistymiseen ja uusiutuvien tuotantomuotojen integroimiseen järjestelmään. Sähköistyminen kasvattaa sähkönkulutusta, joka pyritään kattamaan uusiutuvilla tuotantomuodoilla, lähinnä tuuli- ja aurinkovoimalla. Liikennesektori rajataan kumipyöräliikenteeseen ja sen muutos tulee olemaan haastavin ja aikaa vievin. Muutokseen pyritään liikennepolttoaineiden tuotannolla maakunnassa sekä sähköautoilulla. Uusiutuva energiajärjestelmä tarvitsee tuotannon ja kysynnän joustoa sekä älyä järjestelmältä. Työssä tarkastellaan myös järjestelmän kustannuksia sekä työllisyysvaikutuksia.

Spain and Investment Arbitration: The Renewable Energy Explosion

In the past decade, Spain’s generous incentive system for renewable energy production attracted substantial foreign and national investment. However, when the global financial crisis hit, and the consequent reduction of electricity consumption, the incentives began to cause a tariff deficit in the electricity system, leading the Spanish government to cut back and then eliminate the incentives. In the wake of losses, international investors turned to investment arbitration, while national investors could only present their claims before Spanish courts. The result was a potential for differential treatment between national and foreign investors. This paper examines the incentive regime and the government’s changes to it in order to understand the investors’ claims and the reasoning that resulted in their rejections, both in national courts and in the only arbitration award issued up to now. The paper concludes with a discussion of the effect of the renewable energies situation on the investment arbitration debate within Spanish civil society.

An empirical investigation of the impact of global energy transition on Nigerian oil and gas exports

18 months embargo on the thesis and check appendix for copy right materials

Modelling of a Stirling engine with parabolic dish for thermal to electric conversion of solar energy

Stirling engines with parabolic dish for thermal to electric conversion of solar energy is one of the most promising solutions of renewable energy technologies in order to reduce the dependency from fossil fuels in electricity generation. This paper addresses the modelling and simulation of a solar powered Stirling engine system with parabolic dish and electric generator aiming to determine its energy production and efficiency. The model includes the solar radiation concentration system, the heat transfer in the ther- mal receiver, the thermal cycle and the mechanical and electric energy conversion. The thermodynamic and energy transfer processes in the engine are modelled in detail, including all the main processes occur- ring in the compression, expansion and regenerator spaces. Starting from a particular configuration, an optimization of the concentration factor is also carried out and the results for both the transient and steady state regimes are presented. It was found that using a directly illuminated thermal receiver with- out cavity the engine efficiency is close to 23.8% corresponding to a global efficiency of 10.4%. The com- ponents to be optimized are identified in order to increase the global efficiency of the system and the trade-off between system complexity and efficiency is discussed.

Assessment of the Availability of Forest Biomass for Bioenergy Production in Southwest Portugal.

In 2014, Portugal was the seventh largest pellets producer in the World. Since the shortage of raw material is one of the major obstacles that the Portuguese sellets market faces, the need for a good assessment of biomass availability for energy purposes at both country and regional levels is reinforced. This work uses a Geographical Information System environment and remote sensing data to assess the availability and sustainability of forest biomass residues in a management unit with around 940 ha of maritime pine forest. The period considered goes from 2004 to 2015. The study area is located in Southwestern Portugal, close to a pellets factory; therefore the potential Contribution of the residual biomass generated in the management unit to the production of pellets is evaluated. An allometric function is used for the estimation of maritime pine above ground biomass. With this estimate, and considering several forest operations, the residual biomass available was assessed, according to stand composition and structure. This study shows that, when maritime pine forests are managed to produce wood, the amount of residues available for energy production is small (an average of 0.37 t ha -1  year -1 were generated in the study area between 2004 and 2015). As a contribution to the sustainability of the Portuguese pellets industries, new management models for maritime pine forests may be developed. The effect of the pinewood nematode on the availability of residual biomass can be clearly seen in this study. In the management unit considered, cuts were made to prevent dissemination of the disease. This contributes to a higher availability of forest residues in a specific period of time, but, in the medium term, they lead to a decrease in the amount of residues that can be used for energy purposes.

Numerical modelling and structural optimization of multifunctional maritime structures aimed to protect harbours and produce energy

The main objective of this PhD thesis is to optimize a specific multifunctional maritime structure for harbour protection and energy production, named Overtopping Breakwater for Energy Conversion (OBREC), developed by the team of the University of Campania. This device is provided with a sloping plate followed by a unique reservoir, which is linked with the machine room (where the energy conversion occurs) by means of a pipe passing through the crown wall, provided with a parapet on top of it. Therefore, the potential energy of the overtopping waves, collected inside the reservoir located above the still water level, is then converted by means of low – head turbines. In order to improve the understanding of the wave – structure interactions with OBREC, several methodologies have been used and combined together: i. analysis of recent experimental campaigns on wave overtopping discharges and pressures at the crown wall on small – scale OBREC cross sections, carried out in other laboratories by the team of the University of Campania; ii. new experiments on cross sections similar to the OBREC device, planned and carried out in the hydraulic lab at the University of Bologna in the framework of this PhD work; iii. numerical modelling with a 1 – phase incompressible fluid model IH – 2VOF, developed by the University of Cantabria, and with a 2 – phase incompressible fluid model OpenFOAM, both available from the literature; iv. numerical modelling with a new 2 – phase compressible fluid model developed in the OpenFOAM environment within this PhD work; v. analysis of the data gained from the monitoring of the OBREC prototype installation.

Strategies for lowering the environmental impact of different electrochemical energy storage system

The continuous growth of global population brings an exponential increase on energy consumption and greenhouse gas emission in the atmosphere contributing to the increase of the planet temperature. Therefore, it is mandatory to adopt renewable energy production systems like photovoltaic or wind power: unfortunately, the main limit of these technologies is the natural intermittence of the energy sources that limits their applicability. The key enabling technology for a widespread usage of clean power sources are electrochemical energy storage systems, most commonly known as batteries. Batteries will enable the storage of energy during overproduction period and the release during low production period stabilizing the power outcome, allowing the connection to the main grid and increasing the applicability of renewable energy sources. Despite the high number of benefits that the widespread use of batteries will bring, starting from the reduction of CO2 emitted in the atmosphere, it is necessary also to take care of the environmental impact of processes and materials used for the production of electrochemical storage systems. In addition, there are many different battery systems, with different chemistries and designs that require specific strategies. Nowadays, the most part of the materials and chemicals used for battery production are toxic for humans and the environment. For this reason, this Ph.D. thesis addresses the challenging scope of lowering the environmental impact of manufacturing processes of different electrochemical energy storage systems using natural derived or low carbon footprint materials while increasing the performances with respect to commercial devices. The activities carried out during my Ph.D. cover a high number of different electrochemical storage systems involving a wide range of electrochemical processes from capacitive to faradic. New materials, different production processes and new battery design, all in view of sustainability and low environmental impact, increased the innovative and challenging aspects of this work.