Nanostructured organic layers via polymer demixing for interface-enhanced photovoltaic cells

Significant progress is being made in the photovoltaic energy conversion using organic semiconducting materials. One of the focuses of attention is the morphology of the donor-acceptor heterojunction at the nanometer scale, to ensure efficient charge generation and loss-free charge transport at the same time. Here, we present a method for the controlled, sequential design of a bilayer polymer cell architecture that consists of a large interface area with connecting paths to the respective electrodes for both materials. We used the surface-directed demixing of a donor conjugated/guest polymer blend during spin coating to produce a nanostructured interface, which was, after removal of the guest with a selective solvent, covered with an acceptor layer. With use of a donor poly(p-phenylenevinylene) derivative and the acceptor C-60 fullerene, this resulted in much-improved device performance, with external power efficiencies more than 3 times higher than those reported for that particular material combination so far.

Polymer light emitting devices with Langmuir Blodgett (LB) films of a polyfluorene derivative

Polyfluorenes are promising materials for the emitting layer of polymer light emitting devices (PLEDs) with blue emission. In this work, we report on PLEDs fabricated with Langmuir-Blodgett (LB) films of a polyfluorene derivative, namely poly(9,9-di-hexylfluorenediyl vinylene-alt-1,4-phenylenevinylene) (PDHF-PV). Y-type LB films were transferred onto ITO substrates at a surface pressure of 35 mN m-1 and with dipping speed of 3 mm min -1. A thin aluminum layer was evaporated on top of the LB film, thus yielding a sandwich structure (ITO/PDHF-PV(LB)/Al). Current-voltage (I vs V) measurements indicate that the device displays a classical behavior of a rectifying diode. The threshold value is approximately 5 V, and the onset for visible light emission occurs at ca. 10 V. From the a.c. electrical responses we infer that the active layer has a typical behavior of PLEDs where the real component of ac conductivity obeys a power-law with the frequency. Cole-Cole plots (Im(Z) vs. Re(Z)) for the device exhibit a series of semicircles, the diameter of which decreases with increasing forward bias. This PLED structure is modeled by a parallel resistance and capacitance combination, representing the dominant mechanisms of charge transport and polarization in the organic layer, in series with a resistance representing the ITO contact. Overall, the results presented here demonstrate the feasibility of LEDs made with LB films of PDHF-PV.

Reproductive cycle, ovarian development, and vertebrate-type steroids profile in the freshwater prawn Macrobrachium rosenbergii

This study is intended to characterize the ovarian development and hemolymph vertebrate-type steroids concentration during the reproductive cycle of the freshwater prawn, Macrobrachium rosenbergii. A five-stage classification based on the external observation of the ovary's size and color as seen through the tegument was used. The results showed the existence of a direct correspondence between the ovarian stages and the gonadosomatic index, the oöcyte diameter, and the characteristics of ovarian histology. In each stage total bleeding of the prawns was conducted and the hemolymph concentrations of 17β-estradiol (E 2), testosterone (T) and 17α-hydroxyprogesterone (17-OHP; conjugated and unconjugated) were determined by solid-phase radioimmunoassay (RIA). High levels of unconjugated 17-OHP, relatively constant concentrations of unconjugated T, and null concentration of unconjugated E 2 were found throughout the five stages considered. Nonetheless, low levels of E 2 were determined in all stages, in conjugated (glucoronide) form. The highest levels were obtained in stage II and III (18.14 ± 14.52 pg/ml hemolymph) and progressively declined in the other stages (7.53 ± 6.76 pg/ml hemolymph). These results point out the possible involvement of vertebrate-type steroids in the endocrine regulation of the Macrobrachium rosenbergii's ovarian cycle. To our knowledge this is the first study concerning the vertebrate-like steroid levels throughout the ovarian cycle and is a step needed to characterize the hemolymph profile of these steroids in order to elucidate the possible role in the regulation of the reproductive crustacean cycle.

Hydrophobic effect of amphiphilic derivatives of chitosan on the antifungal activity against aspergillus flavus and aspergillus parasiticus

Low molecular weight amphiphilic derivatives of chitosan were synthesized, characterized and their antifungal activities against Aspergillus flavus and Aspergillus parasiticus were tested. The derivatives were synthesized using as starting material a deacetylated chitosan sample in a two step process: the reaction with propyltrimethylammonium bromide (Pr), followed by reductive amination with dodecyl aldehyde. Aiming to evaluate the effect of the hydrophobic modification of the derivatives on the antifungal activity against the pathogens, the degree of substitution (DS1) by Pr groups was kept constant and the proportion of dodecyl (Dod) groups was varied from 7 to 29% (DS2). The derivatives were characterized by 1H-NMR and FTIR and their antifungal activities against the pathogens were tested by the radial growth of the colony and minimum inhibitory concentration (MIC) methods. The derivatives substituted with only Pr groups exhibited modest inhibition against A. flavus and A. parasiticus, like that obtained with deacetylated chitosan. Results revealed that the amphiphilic derivatives grafted with Dod groups exhibited increasing inhibition indexes, depending on polymer concentration and hydrophobic content. At 0.6 g/L, all amphiphilic derivatives having from 7.0 to 29% of Dod groups completely inhibited fungal growth and the MIC values were found to decrease from 4.0 g/L for deacetylated chitosan to 0.25-0.50 g/L for the derivatives. These new derivatives open up the possibility of new applications and avenues to develop effective biofungicides based on chitosan. © 2013 by the authors.

Rheological behavior of binary aqueous solutions of poly(ethylene glycol) of 1500 g·mol-1 as affected by temperature and polymer concentration

The rheological behavior of poly(ethylene glycol) of 1500 g·mol -1(PEG1500) aqueous solutions with various polymer concentrations (w = 0.05, 0.10, 0.15, 0.20 and 0.25) was studied at different temperatures (T = 283.15, 288.15, 293.15, 298.15 and 303.15) K. The analyses were carried out considering shear rates ranging from (20 to 350) s-1, using a cone-and-plate rheometer under controlled stress and temperature. Classical rheological models (Newton, Bingham, Power Law, Casson, and Herschel-Bulkley) were tested. The Power Law model was shown suitable to mathematically represent the rheological behavior of these solutions. Well-adjusted empirical models were derived for consistency index variations in function of temperature (Arrhenius-type model; R2 > 0.96), polymer concentration (exponential model; R2 > 0.99) or the combination of both (R 2 > 0.99). Additionally, linear models were used to represent the variations of behavior index in the functions of temperature (R2 > 0.83) and concentration (R2 > 0.87). © 2013 American Chemical Society.

Investigação da transição isolante-metal do CDM via algoritmos computacionais e estudo de nano-dispositivos orgânicos

Apresentamos neste trabalho um estudo teórico sobre polímeros orgânicos conjugados. É conhecido que estes sistemas, em geral semicondutores ou isolantes, sob dopagem química podem vir a adquirir propriedades elétricas de material condutor. E ainda, sob ação de campo elétrico, pequenos oligômeros podem apresentar comportamento equivalente ao de dispositivos usuais, mas com inúmeras vantagens como, por exemplo, tamanho extremamente reduzido (alguns nanômetros). Dessa forma no primeiro capítulo faremos uma breve introdução sobre polímeros orgânicos conjugados mostrando alguns resultados experimentais obtidos para o polímero 4-dicianometileno-4,4-ciclopenta [2,1-b: 3,4b’] ditiofeno – CDM, que é o objeto central de estudo desta dissertação. O capítulo 2 trata dos métodos quânticos utilizados. Citaremos a Teoria de Hartre-Fock (HF) e suas derivações semi-empíricas. A técnica de Interação de configuração (CI) e a Teoria do Funcional da Densidade (DFT) também serão tratadas neste capítulo. O capítulo 3 é dedicado a descrever as características de alguns dispositivos usuais como diodos e transistores. Aqui o fundamental é entender a composição, o funcionamento e principalmente, como se comportam suas curvas características corrente versus voltagem (IxV). Citaremos ainda alguns dispositivos eletrônicos extremamente pequenos. No capítulo 4 começa nossos resultados e discussões referentes a análise da transição isolante-metal em CDM sob ação de dopagem. Primeiramente a nível semiempírico, obtivemos a caracterização ótica de oligômeros de CDM neutro e na presença de defeitos conformacionais do tipo bipólarons negativo e positivo. Partindo de geometrias otimizadas via métodos AM1 e PM3 obtivemos o espectro de absorção para sistemas com e sem carga. A nível Hartree-Fock calculamos a Estrutura de Bandas e a Densidade de Estados (DOS) para o PCDM no estado neutro e dopado. O cálculo da DOS e da Dispersão foram realizados através de programas computacionais desenvolvidos aqui no Grupo de Física de Materiais da Amazônia (GFMA). Apresentamos ainda neste capítulo o espectro de absorção teórico para oligômeros de CDM com diversas configurações com geometrias totalmente otimizadas pelo DFT. No capítulo 5 temos os resultados relativos à análise de nanodispositivos baseados em tetrâmeros de CDM com e sem carga. As curvas do deslocamento de carga versus voltagem apresentam características de curvas de dispositivos usuais. Analisamos também o espectro de absorção teórico dos nanodispositivos para valores de tensão nula e em pontos de saturação de corrente nas regiões direta e reversa.

Efeito da adição de moléculas anfifílicas na formação de filmes Langmuir e Langmuir-Blodgett de derivados alquilados do politiofeno: aplicação em sensores

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Polymer Matrix-Based Piezoelectric Composite for Structural Health Monitoring

Structural health monitoring (SHM) refers to the procedure of assessing the structure conditions continuously so it is an alternative to conventional nondestructive evaluation (NDE) techniques [1]. With the growing developments in sensor technology acoustic emission (AE) technology has been attracting attention in SHM applications. AE are characterized by waves produced by the sudden internal stress redistribution caused by the changes in the internal structure, such as fatigue, crack growth, corrosion, etc. Piezoelectric materials such as Lead Zirconate Titanate (PZT) ceramic have been widely used as sensor due to its high electromechanical coupling factor and piezoelectric d coefficients. Because of the poor mechanical characteristic and the lack in the formability of the ceramic, polymer matrix-based piezoelectric composites have been studied in the last decade in order to obtain better properties in comparison with a single phase material. In this study a composite film made of polyurethane (PU) and PZT ceramic particles partially recovered with polyaniline (PAni) was characterized and used as sensor for AE detection. Preliminary results indicate that the presence of a semiconductor polymer (PAni) recovering the ceramic particles, make the poling process easier and less time consuming. Also, it is possible to observe that there is a great potential to use such type of composite as sensor for structure health monitoring.

Measurement of Radiant Energy using Pyroelectric Polymer/Ceramic Composite

Monitoring non-ionizing radiant energy is increasingly demanded for many applications such as automobile, biomedical and security system. Thermal type infrared (IR) sensors can operate at room temperature and pyroelectric materials have high sensitivity and accuracy for that application. Working as thermal transducer pyroelectric sensor converts the non-quantified thermal flux into the output measurable quantity of electrical charge, voltage or current. In the present study the composite made of poly(vinylidene fluoride) -PVDF and lead zirconate titanate (PZT) partially recovered with polyaniline (PAni) conductor polymer has been used as sensor element. The pyroelectric coefficient p(T) was obtained by measuring the pyroelectric reversible current, i.e., measuring the thermally stimulated depolarization current (TSDC) after removing all irreversible contribution to the current such as injected charge during polarization of the sample. To analyze the sensing property of the pyroelectric material, the sensor is irradiated by a high power light source (halogen lamp of 250 W) that is chopped providing a modulated radiation. A device assembled in the laboratory is used to change the light intensity sensor, an aluminum strip having openings with diameters ranging from 1 to 10 mm incremented by one millimeter. The sensor element is assembled between two electrodes while its frontal surface is painted black ink to maximize the light absorption. The signal from the sensor is measured by a Lock-In amplifier model SR530 -Stanford Research Systems. The behavior of the output voltage for an input power at several frequencies for PZT-PAni/PVDF (30/ 70 vol%) composite follows the inverse power law (1/ f) and the linearity can be observed in the frequency range used.

Effect of the length of alkyl side chains in the electronic structure of conjugated polymers

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Phenomenological model for the interpretation of impedance/admittance spectroscopy results in polymer light-emitting electrochemical cells

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Obtenção e estudo de polímeros supramoleculares derivados de ácidos carboxílicos-meglumina em fase aquosa

Pós-graduação em Química - IQ

Synthesis, Characterization, and Antifungal Activities of Amphiphilic Derivatives of Diethylaminoethyl Chitosan against Aspergillus flavus

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Extraction of natural red colorants from the fermented broth of Penicillium purpurogenum using aqueous two-phase polymer systems

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Gamma-ray dosimetric properties of conjugated polymers in solution

The effect of gamma radiation on poly{[2,5-bis(3-(N,N-diethylamino)-1-oxapropyl)-1,4-phenylene]-alt-1,4- phenylene} (PPP); poly{[2,5-bis(3-(N,N-diethylammonium bromide)-1-oxapropyl)-1,4-phenylene]-alt-1,4-phenylene} (PPP-Br); and the polymerized dye poly-1-ethyl-2-[3-(1-ethyl-1,3-dihydro-3,3-dimethyl-2H-indol-2-ylidene)-1-propenyl]- 3,3-dimethyl-3H-indolium perchlorate (Poly-CyC) has been investigated. The stability and response of poly [2-methoxy- 5-(2'- ethyl-hexyloxy)-p-phenylenevinylene] (MEH-PPV) in mixed solutions have also been explored. To this end, samples with concentrations ranging from 0.005 to 0.500 mg/mL were irradiated with a 60Co gamma-ray source at room temperature, using doses up to 1 kGy, and the response was analyzed by UV-Vis spectroscopy. The obtained results reinforce the previously proposed mechanism and suggest that the effect depends on specific structural characteristics of the main chain of the polymers. Moreover, the polymerized dyes display interesting dosimetric properties. Additionally, it has been noted that, contrary to what happens in other solvents, MEH-PPV is degraded in bromoform solution. Protective effects have also been observed for bromoform+toluene mixtures (1:1 vol/vol) and solutions containing molecular dyes. - See more at: http://www.eurekaselect.com/117251/article#sthash.gHFnYvJk.dpuf